Search Documents

By J. P. Caulfield

THE Hudson Bay Mining and Smelting Company's underground mine at Flin Flon, Manitoba, has in the past been serviced by two working shafts-the North Main shaft, and the No. 3 shaft. The North Main shaft is used to hoist the total production from under-ground, and handles the greater part of the mine supplies and crews. The shaft is five-compartment design, rectangular in cross-section, and is equipped entirely with steel shaft sets from the surface to the finished depth of 2,210 feet. Hoisting equipment in the surface plant will not permit the North Main shaft to be extended below its present finished depth. The No. 3 shaft, located approximately 2,300 feet from the North Main shaft, is used primarily as a ventilation shaft, and for hoisting lower-level development waste to the 390 level, where this material is used as mine fill. The No. 3 shaft is of standard rectangular design, timbered with 8-in. by 8-in. creosoted fir sets, hung on 6-foot centres. From the surface to the 1,430 level, the No. 3 shaft consists of three 5 ft. by 5 ft. compartments, and below this level to the completed depth of 2,300 feet, the shaft is increased to four compartments. To service the mine and to expedite development below the 2,210 level, a one and one-half compartment winze was sunk from the 2,210 level to a depth of 766 feet, or approxima tel y the 3,000 level.

Jan 1, 1941

By J. Yue

"Mount Milligan mine is located in northern British Columbia. The concentrator employs conventional SABC grinding circuit with bulk sulphide flotation processes. Commissioning started in September of 2013 and nameplate production of 60,000 TPD was reached in the fourth quarter of 2015. As is typical with many mill ramp ups, bottlenecks developed as throughput increased. Since then, plant modifications and new control philosophies in the comminution and flotation circuits have been implemented and evaluated. The mine-to-mill collaboration played a key role in reaching target throughput rates by improving blast fragmentation and implementing temporary pre-crushing. Results of the projects as well as ongoing challenges/bottlenecks and solutions will be discussed.IntroductionMount Milligan Mine is a copper-gold producer located approximately 253 km northwest of Prince George in British Columbia. Production commenced in September 2013 and reached nameplate capacity of 60,000 TPD in December 2015. Average head grades for the mine life average 0.18% Cu and 0.39 g/t Au.Circuit DesignOriginal process design began with run-of-mine ore from the pit crushed through a 60-110 gyratory crusher, conveyed to a live ore stockpile and fed to the mill via four variable apron feeders. The concentrator circuit employs SAG mill - Ball mill - Pebble Crusher (SABC) grinding configuration to grind the ore down to a target P80 of ~200µm. It is then fed to two parallel trains of flotation tanks, each consisting of five 200 m3 tank cells with the first two being roughers and last three being scavengers. Concentrate streams from roughers and scavengers are separately reground with a closed circuit Tower mill and two open circuit ISA mills operating in parallel, respectively.Three stages of cleaners upgrade roughers/scavenger products to 25% Cu followed by a cleaner scavenger stage. The final concentrate is then thickened and filtered to approximately 9% moisture and shipped off site (Figure 1)."

Jan 1, 2017

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008

By V. “Ram” Ramachandran

"In view of the increasing number of environmental regulations that have been promulgated all over the world in the last thirty years, non-ferrous smelters and refineries have had to learn and adapt to treating process bleed waste streams containing heavy metals. The result of such treatment invariably yields a gypsum-saturated solution containing salts such as alkali metal sulfates, chlorides and fluorides. Presence of anions such as sulfates, chlorides and fluorides in the discharge streams – presently not a major problem- are coming under increasing scrutiny and will have to be addressed in the near future. It is envisaged that discharge limits for sulfate ions will be in place in the near future. Treatment of brackish water to produce drinking water also results in brine streams containing alkali salts that have to be addressed for proper disposal. This paper reviews treatment options for such streams containing high levels of total dissolved solids with emphasis on sulfate removal. Areas covered would be: a) chemical treatment for removal of various constituents that make up the total dissolved solids b) processes for sulfate removal processes –thermal and non-thermal-to recover and reuse of treated water and c) brine use and treatment options.INTRODUCTIONThe rising cost of water and meeting the ever-changing stringent environmental discharge regulations make water recycling and reuse essential. The metallurgical industry has used water as a medium for dissolving and/or rejecting metals and chemicals in addition to removing thermal energy. Any excess process effluent is collected and sent to end-of-pipeline treatment and ultimately discharged to surface water for disposal under a permit. The conventional- and probably the cheapest way -of treating metal-bearing process effluent streams is lime neutralization followed by sulfide polishing for elimination of heavy metals to produce a stream that meets NPDES discharge limits. This results in a stream containing dissolved solids.These dissolved solids normally comprises of inorganic salts. The possible constituents are cations calcium, magnesium, sodium and potassium. The anions are sulfate, chloride, fluoride, nitrate, carbonate and bicarbonate. In addition to these constituents, the treated effluent streams contain very small amounts of heavy metals, oxyanions such as arsenites, arsenates, selenites and selenates. Process streams from gold operations contain residual cyanide. Small amounts of ammonium ions are also present in these streams based on the pH of the solution."

Jan 1, 2012

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By Jean M. Richardson, Steven R. Williams

"Geometallurgical mapping is a new team-based approach that documents variability within an orebody and quantifies the impact of geology (host rocks, alteration and structure) and mineralogy on grinding, metallurgical response and metal recovery processes. The quantitative, spatially constrained database that results can be readily integrated into 3-D block models and mine planning activities. Thus it is an important tool to reduce the technical risk associated with new mine developments or expansions.Normally undertaken during pre-feasibility or feasibility planning stages, the first step of geometallurgical mapping is to review the geology, mineralogy and other critical parameters and construct a geometallurgical matrix. This matrix provides an objective base to then guide sampling and/or compositing activity for physical property and metallurgical testing. Depending on the project, an array of testing techniques can be used to characterize the ore and feed data into the geometallurgical model.While the range and number of tests needed is project-dependant, the geometallurgical mapping approach allows the development of empirical models or interdependent relationships, grounded by spatially-constrained real data. Extensive data sets collected using less expensive testing methods can be meaningfully correlated with results from complex specialty tests to yield realistic metallurgical recovery data.With geometallurgical mapping completed, the resulting database can be integrated into an overall 3-D block mine model. This means that metallurgical response can be used to realistically forecast the recoveries of specific blocks, perhaps sampled only by drilling. Mine planning can then incorporate the forecasted metallurgical response and generate future project cash-flows; opening the door to economic optimization of the mine exploitation."

Jan 1, 2004

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003

By B. Pewkliang, K. Ehrig, E. Macmillan, M. Smith, V. Liebezeit, Y. Li

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is the largest publicly declared uranium, fifth largest copper and third largest gold resource. Currently, the operation consists of an underground mine and integrated processing plant. Uranium is produced from leaching of flotation tailings and is a co-product to copper cathode with by-product gold and silver bullion. The Olympic Dam geometallurgy team began studying ore from the Southern Mine Area (SMA) in 2006 and soon discovered uranium behaviour was far more variable than the behaviour in the Northern Mine Area, which had been mined from the start of the operation in 1988. The primary objective of Olympic Dam geometallurgy is to develop metallurgical performance predictors that reliably describe the process performance of different ore types and distribute these into the resource block model for use as a fundamental input into mine planning. The nature of the uranium mineralisation (compositionally and texturally complex and highly variable) meant that classic mineralogy techniques alone could not provide the resolution required for prediction of uranium extraction. However, the combination of quantitative mineralogy, results from laboratory-scale leach tests and modelling within the geometallurgy program has enabled prediction of both uranium flotation recovery (via association with sulphides) and uranium leach extraction, including at variable leach conditions. These stope-based predictions have supported trade-off decisions between operating costs and uranium revenue, and have predicted the changing recovery as the mining operations have moved into the Southern Mine Area in recent years.

Jan 1, 2020

By Robert Gannicott

??A mining company without the burden of operating a mine ??Management focused on marketing a high-quality, run-of-mine range of Canadian diamonds ??Robust revenue stream ??Specialist diamond knowledge ??Canadian exploration and development expertise ??BUT ??Single asset revenue base from depleting ore reserve ??Limited influence on production plans

Apr 1, 2005

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.  This is the result of the social and financial accountabilities that the industry is faced with because of the world’s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).  To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.  In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.  It follows that comminution is the major greenhouse gas emission process of the mine.  All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.  In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.  This paper makes a definitive contribution to that discussion.  The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.  Major emission contributors, steel, natural gas and electricity are discussed in detail.  The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.  The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.  Emerging steel making technologies are presented and discussed.  The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.  Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.  The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.  Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

IDS: The Company IDS Ingegneria Dei Sistemi, founded in 1980, is a world leader as a high technology solution provider in selected niche defense and civil market sectors ? Private and Independent ? IDS?s Quality System is certified ISO 9001 Ed. 2000 ? IDS has the highest Military Clearance ? Continuously measure (24x7) mine wall movements with sub-millimetric accuracy at long distance (up to 4 Km) ? Provide reliable early warning for progressive slope movements potentially leading to mining wall failures ?Map the long term evolution of slow moving slopes to get a better knowledge of the rock mass strength

Aug 1, 2013