Search Documents

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By Robert Halupka

The industrial minerals sector represents a broad range of products involving a variety of technologies serving a diversity of markets and end uses. Unit values of products vary widely, reflecting the peculiarities of each product/market sector. Generalizations are therefore understandably difficult to make and borrowers may need to take extra time to "educate" lenders on the key aspects of their business and industry sub-sector. This paper will examine the factors and the thinking that lenders apply when considering financing proposals to companies in the industrial minerals sector. If you understand the lender's perspective and their concerns, then you can make better use of your own time and resources when arranging financing for your company or project.

Jan 1, 2001

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By K. Schrijver, G. Beaudoin

"Four occurrences of galena-cemented sandstones, exposed in the Lower St. Lawrence - Gaspésie area, are described. They constitute a new, insufficiently explored type of deposit in Quebec.One mineralized body, a minor occurrence, is hosted in Lower Devonian rocks deposited in an estuarine, intertidal river channel during a marine regression; major cements are dolomite and sulphides. Another occurrence, a drilled prospect, is hosted in Upper Silurian rocks deposited unconformably on Cambro Ordovician basement during a marine transgression. With galena and quartz as main cementing minerals, it is similar to some well-known, economic sandstone-lead deposits. A third and fourth, a drilled prospect and a minor occurrence, are hosted in Upper Cambrian rocks deposited on continental slopes. In both, sulphides mainly occupy a secondary porosity. The differences between the third and fourth occurrences are: (1) cementing translucent minerals (carbonates and barite in one; chlorite in the other); (2) chronology of final subsurface dissolution (prior and subsequent to sulphide precipitation, respectively); and (3) important fracture porosity only in the barite-bearing deposit.The diversity of the four occurrences, and the unequal geological knowledge of their respective features, prohibit the formulation of uniform guidelines for further exploration.IntroductionThe attention of the mineral exploration community is drawn to four occurrences of galena-cemented sandstones (Fig. 2A) in the Cambrian of the Taconian Orogen and in the Siluro-Devonian basin of the Lower St. Lawrence and Gaspésie area (Fig. 1). In view of the fact that sandstone-lead deposits (Bjerlykke and Sangster, 1981) are, or have been, mined in several countries (e.g . Laisvall in Sweden: see Rickard et al., 1979; Largentiere in France: see Foglierini et al., 1980), the mere presence of occurrences in Quebec indicates that the mineral potential of some parts of the Appalachians requires further evaluation.Exploration for the deposits considered here is essentially restricted to geological methods and drilJing (e.g . Mainguet Suares and Samama, 1969), since the response to geophysical methods is virtually nil, at least in the initial, surficial stage of an exploration program. As the particular disciplines of geology utilized in exploration depend a great deal on the geological setting of a mineral occurrence, the diversity of the Quebec deposits is of prime importance. Therefore, the four occurrences (Fig. I, Table 1) studied by the authors are herein briefly described with emphasis on their stratigraphic and tectonic setting, and on the evolution of pore space and sequential occlusion of pores and fractures. Prior to further research in and around the occurrences, now in progress (e.g. Beaudoin, 1987; Beaudoin et al., 1987), it is hoped that the following outline will be useful to the explorationist."

Jan 1, 1987

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By H. P. Jacobi

"The last 25 years have seen tremendous economic pressure placed upon the base metal processor. Industry has responded with technological innovations that have contributed to significant reductions in capital and operating costs. Major changes in processing machinery and philosophy are highlighted for the main unit operations of a base metal mill. Changes in our attitudes on what is environmentally acceptable are also discussed.INTRODUCTIONNewton's law of motion paraphrased states that nothing will change unless there is a pressure to do so.Aase metal processing as a primary commodity related industry has been under severe economic pressure over the last 25 years. This has been brought on by over capacity from new operations in the L.D.C. 's, through material substitution in a host of traditional base metal applications and generally reduced world-wide economic activity. In addition to shrinking markets our collective environmental consciousness has raised effluent standards and workplace hygiene and the employee's as well as government's economic expectations of how much ought to be derived from ''nature's riches''.Industry has responded with technological changes which, it was hoped, would counteract the cost squeeze in which it found itself.I would like to briefly enumerate the major changes, as I see them, that have taken place in the main unit operations that form the normal processing chain for base metals.While the following paper will mention several brands of products, I would like to emphasize that these are the ones that I am most familiar with and is not to say that they are the only manufacturers which have contributed to changes. In fact it ls fair to say that all makers of mining and processing equipment have made improvements to their products, to a greater or lesser degree; they have had to, to still he in business in 1986."

Jan 1, 1987

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By C. Jay Hodgson

Hydrothermal systems form on land where and when an impermeable cap-rock unit ( either natural or self-sealed) , a permeable aquifer. and permeable discharge and recharge channels (cross-stratal permeability) develop in an anomalously hot part of the crust. A consideration of the relationship between magmatic and tectonic events in volcanically active areas indicates these conditions arise during: (1) the resurgent doming stage of the resurgent caldera cycle; (2) following movement on the bounding faults of tilted fault blocks ; and (3) as a result of hydrothermal boring associated with the intrusion of major sills. On the assumption that the submarine hydrothermal systems which deposit volcanogenic massive sulphide ores are comparable to subaerial hydrothermal systems, it is suggested that: (1) the horizon of mineralization corresponds to the time period when conditions favour the development of hydrothermal systems, as outlined above; (2) exploration for Cu-rich Cu-Zn-Pb or Cu-Zn ores should be directed to paletopographically high areas near discharge conduits , whereas exploration for Cu-poor ZnPb ores should concentrate on paleotopographically low areas down slope from conduits; (3) deposits with stringer zones lying above normally permeable units may be underlain by regionally extensive weakly mineralized and altered zones (self-seal caps) ; (4.) in the absence of a self -sealed cap, the ore horizon may be underlain by a naturally impermeable unit (e .g. a fine clastic sediment) ; (5) the condition of cross-stratal permeability may be evidenced by features such as dykes. alignment of vari ous magmatic and hydrothermal phenomena, abrupt thickness changes in stratiform units indicative of ponding against syn-volcanic faults, and fault-scarp slump deposits; (6) the condition of high heat flow may be evidenced by near-surface magmatism and steep thermal gradients preserved in metamorphic mineral assemblages.

Jan 1, 1977

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By Gordon Sproule

THE papers presented to the Institute, and published in the BULLETIN, in the past three years, may be classified as follows: Geology, Mining, and Milling 89 or 58.5 per cent Smelting, Refining, and Refractories 17 " 11.2 " Mechanical and Physical Metallurgy 7 " 4.6 " General (Economics, Welfare, etc.) 39 " 25.7 " Total 152 100 These figure~ should be excuse enou.gh for. the present paper. As indicated by the title it is proposed: I.-To review briefly some of the more recent developments of Physical Metallurgy; and 11.-To show how Physical Metallurgy functions as the link between mining and production metallurgy on the one hand, and consumption engineering on the other hand. Io these days of specialization, papers of the kind being considered mostly gravitate to the American Society for Metals, the American Society for Testing Materials, the Institute of Metals, and the Iron and Steel Institute. In proof that there is a place for the newest and most specialized of these societies, the American Society for Metals, it may be said that in the Montreal Chapter there are 200 active members, and in the Ontario Chapter more than 200. Yet the overshadowing glamour of the mining industry proper, and the publicity it receives, result in an almost continuous dearth of students in metallurgical engineering at our universities. There are more jobs than graduates.

Jan 1, 1936

By W. E. Segsworth

Introduction By far the largest part of the money raised for mining is raised by honest and legitimate means; but a not inconsiderable amount is raised by fraudulent sales methods. It will be conceded without argument that the greatest menace to the mining business is the fraudulent promoter. The sale of worthless mining stocks to the public by high-pressure. salesmen, house to house canvassers, telephone campaigns, fraudulent use of the mails, fraudulent statements, and reloading, has seriously prejudiced the public against even legitimate mining. A very small percentage of the funds raised by such fraudulent means is ever spent on the property, but instead is absorbed by the promoter in illegitimate' profits, enormous commissions, high office rents, and other expenditures, and is just so much subtracted from the fund which the legitimate developer needs to bring new mines to the point of production. The mining fraternity has been at fault in that, while they recognized this situation, they made no adequate attempt to rectify it. They knew that these fraudulent practises were conducted by parasites who attached themselves to the mining business in boom times and claimed to be part and parcel of it, but who were merely professional salesmen and promoters who, when there was not a mining boom, were selling sky-line real-estate, worthless oil stocks, or fraudulent securities which happened to be popular with the public. While mining people had this distinction well in mind, the public did not differentiate between the crooked promoter temporarily selling fraudulent mining stock and the honest promoter who made mining finance his life work; and we did little to make this distinction clear to the public or to sweep these money grabbers out of our house. The historic boom of 1927-8 and '29 brought with it the usual crop of crooked mining promoters, and the scandals resulting from their operations forced the Governments into the enactment of laws to attempt to protect the gullible public against the operations of these meanest of thieves and to appease public clamour.

Jan 1, 1934

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By L. A. Ayres da Silva, J. P. G. Negri, A. L. M. Ayres da Silva

"Rock hardness is dependent on the type and quantity of the various mineral constituents of the rock and the bond strength that exists between the mineral grains. As the book “The Complete ISRM Suggested Methods For Rock Characterization, Testing and Monitoring:1974-2006” explains, hardness is a concept of material property. As such, the quantitative measure of hardness depends on the type of the test employed.Among the three types of tests that have been used to measure the hardness of rocks and minerals: 1) indentation tests; 2) dynamic and rebound tests; 3) scratch tests, the authors of this paper chose indentation tests, more specifically the Vickers test, and complementary verified the correlation between the results of the Schmidt sclerometer tests (rebound tests) and the Vickers microhardness tests in a set of the same 9 (nine) granite rocks.The objective of this research was to verif y the correlation of one created index, based on the Vickers test that can be able to represent the rock material hardness. We know that Vickers tests determine the microhardness of individual rock minerals. A pyramidal shaped diamond is applied to the surface with a specified force. The area of the permanent residual deformation divided by the applied force is a measure of the hardness. Using the relative participation of the mineral components of the rock, we established a hardness index denominated EVM (Equivalent Vickers Microhardness).The correlation of the EVM with others strength properties and application parameters like UCS (Uniaxial Compressive Strength) to study sawability of granite blocks have presented very good results. The association of equivalent microhardness with others strength parameters, allowed to find powerful algorithms for analyzes of the rock materials behavior under diversified circumstances, as the sawability of granite blocks, as we can see in Fig. 1.Other very interesting correlations were found as the EVM values and that were obtained by the use of the Schmidt impact hammer for the superficial hardness determination."

Jan 1, 2015

By Neil H. Brown

Outline ? Cameco - Cigar Lake ? Cigar Lake Mine Development ? MDS #1 ? MDS #1 Improvements ? MDS #2 ? MDS #2 Improvements Pending ? Acknowledgements Mine Development System ? Mining methods tested and developed over the years ? Construction began officially in 2005 ? Water inflow events in 2006 and 2008 ? Successful dewatering and re-entry in 2010 ? Remediation continues ? Production target is mid-2013

Oct 1, 2010

By R. A. Sullivan

I T IS one of the unwritten policies at Preston Mines that we examine closely any method or tool that will help us in our constant battle against rising costs. It is our personal conviction that most work methods can be improved. Therefore even though the job went well yesterday, it does not necessarily follow that it should be done by the same method today. With the arrival of the natural gas pipe line in the Porcupine area it was obvious that we would have to take a good look at the possibilities of using this source of fuel for plant heating. • Steam presently generated at Preston is for heating purposes only, no process steam being required. Prior to the fall of 1960, the heating plant consisted of two low pressure, coal-fired, fire-tube boilers, operating at an approximate pressure of 14 pounds per square inch. These boilers were underfed by stokers and could be operated either singly or together. ~o. 1 unit was a horizontal return tubular boiler, registered at 100 h.p. No. 2 unit was a fire-box boiler, registered at 75 h.p.

Jan 1, 1962