Search Documents

By E Werner, B R. Leavitt

The chemistry of acidic mine drainage discharging from flooded coal mines is commonly reported to improve with time after flooding. This investigation describes a 18-year dataset of post-flooding water chemistry for a below-drainage underground coal mine within the northern Pittsburgh coal basin (Pennsylvania, USA). The Montour mine is a 5650-hectare below-drainage coal mine of maximum 260 metres depth. Montour was closed in 1980 and flooded to within 38 metres of land surface within 4.8 years. Pumping averaging 210 L/s was then employed to maintain water levels at this elevation. The flooded proportion of the mine (by volume) at full flooding was 56 per cent. The shaft where water was pumped from Montour for water control is located about 70 per cent of the distance between the mine water table and the back of the mine ù that is, it is close to the back of the mine. The residence time (total water volume at flooding divided by pumping rate for control) is estimated at 5.6 years. Time series of chemical analyses show three phases of chemical behavior in post-flooding discharge. In Phase I (zero to two years after flooding), iron concentrations were high and reached their maximum (1100 mg/L). In Phase II (two to four years after flooding), a transition was begun to alkaline conditions, with decline in iron and other solutes. In Phase III (>4 years), net alkaline conditions began, with iron concentrations declining exponentially to 50 per cent of mined volume. This attainment of net alkalinity in this case may have also depended on abundant calcite in overburden extended up to 30 m above the mine floor.

Jan 1, 2003

By Smith R. N

The Olympic Dam copper-uranium-gold-silver deposit is located approximately 520km north-northwest of Adelaide, South Australia. The deposit was discovered in 1975 by the Exploration Division of Western Mining Corporation (WMC). A joint venture, to facilitate development of the deposit was formed in mid 1979 between WMC (51%) and the British Petroleum Group (BP) (49%).

Jan 1, 1990

By Stewart A. M, Price D

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings are based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations.

Jan 1, 1992

Risk Management has been applied relatively slowly in the mining industry. Except for the risk concept application in financial considerations, the application of Risk Management in safety management has been far from satisfactory. When applied it was treated in a global occupational safety and health sense. Regardless of how much the mining industry has progressed over the years it is still, in many respects, `state-of-the-art' business. The safety aspects of mining are well known and yet little understood by the public. Regardless of what has been achieved so far and how much effort has been put into it, mining is regarded as an unsafe and somehow rude business. Safety records of the mining industry vary from State-to-State. Latest mining related disasters in PNG and Queensland and some other fatal accidents support this public perception. They purport a need for change in managing safety in the mining industry. The latest mining fatalities have raised the issue: What must be done to improve safety standards? Duty of care, risk management and system engineering concepts can provide some answers. Risk Management principles which have been advocated for some time provide many answers and explanations and can make safety management more constructive and workable. What has been missing so far is that this concept has neither been applied nor has been modified for its practical application and purpose on a larger scale. A risk management approach to the management of safety and health in the mining industry is addressed, herein. This approach does not attempt to provide the solution. It does, however, provide a basic understanding of what Risk and Risk Management are all about. Rational management of risk is addressed in the life cycle and system contexts. A system of continuous improvement is applied. There is always a chain of events, outcome, exposure, consequence(s), and consequence(s) value(s). It means that development of an event takes place in time and space. Dynamic circumstances have been created in or within the system. It is a decision-making process designed to provide a methodology which is directed not toward a mathematical model but toward easy use and application in dynamic working environment, by decision-makers who can be anybody from either a risk taker or a risk creator. The emphasis is placed not only on arriving at the best practical, possible and fair decision but also on structured and systematic acquisition of knowledge about the system, its hazards and associated risks, hence increasing the decision maker's ability to manage the decision-making process related to the management of risk.

Jan 1, 1995

The application of reinforcement techniques to enhance the stability of underground coal mine roadways subject to high stresses is discussed. Research conducted in the Illawarra Coal Measures has been aimed to delineate the factors which influence the behaviour of rock above roadways and the performance of the reinforcement placed. Design considerations for the reinforcement of mine roadways in the Bulli coal are based on a quantification of the rock response together with a reinforcement strategy to enhance the structural integrity of the roof strata.

Jan 1, 1986

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

Life inside the mining family was regulated by the mine. The whistle shrieked the change of shift to the Cornish, Welsh and German miners digging the alien soil for copper at Burra in the 1840s and the deep quartz gold mines at Bendigo in the 1880s.During the golden years of alluvial mining in the 1850s, and later out on the frontier fields of Kalgoorlie and Jarrahdale in Western Australia, the lure of the mine dominated family life. How could it do anything else? The canvas tent, bark hut or weatherboard cottage in which the mining family lived close by the mine facilitated prompt access. The working man of the family attended to the demands of the mine first, and those of his family afterward. Who then organized and nurtured the mining family? The role of the mining wife was multi-fold. She played the traditional roles of home-maker and comforter, raising her children, tending her house and vegetable garden and supporting those friends and acquaintances who had lost children to disease, or menfolk to the mine. Epidemics of measles, the whooping cough or influenza carried away children in infancy or at too young an age. The death of a husband through accident or disease (pthisis was a likely killer) forced upon the mining wife another role, that of provider. When Elizabeth Vigus' husband died in a Bendigo mine accident in March 1880 Elizabeth set up a grocery business to support her young children.' But in other cases the mining wife supplemented the family earnings by part time work, not in the mines for the Mines Act legislation of 1842 forbade the working of women underground, but in auxilfiary occupations which were in demand.2 Ann Mitchell, a herbalist ,found plenty of work in the goldfield towns of Daylesford and Maldon in the 1860s and 1870s.3 So too did Susan Rule and her daughter Catherine who conducted a sewing and millinery establishment in Beechworth in the 1870s.4 The making of the family's clothes was another task of the mining wife and mother.Until the wonderful invention of the sewing machine, this was a tedious and time-consuming task. James Slater Edmonson bought his wife a Wertheim for the sum of 12 pounds in June 1886, just before leaving her and his chil- dren in the Adelaide suburb of Goodwood whilst he went alone to the goldfields of the West. In October of that year he wrote to Louise telling her how he missed the childrens' wondering "whether Slater wore my old shirt now. I always think of him as he sat on my knee at breakfast in that old shirt; and how pleasant it would be if I could rock both of them and sing as I used to do".5

Jan 1, 1988

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

By Breen AM, Phelan JM, Doherty RJ

Early in 1990, Pancontinental Resources (Base Metals) Pty Ltd commenced flotation treatment of ore from the complex copper-lead-zinc sulphide orebody at Thalanga, 65 km west of Charters Towers in North Queensland. The orebody consists mainly of primary sulphide ore but also contains a substantial proportion of supergene ores which are being processed during the first year of operations. The supergene ores are of three main types, designated as A, B, and C. Supergene A ores are essentially copper ores, containing little lead and zinc, while B and C ores are copper-lead-zinc ores with different degrees of alteration of the original chalcopyrite and different ratios of copper to zinc content. Copper is present in the supergene ores mainly as chalcocite, digenite and covellite. Lead and zinc occur mainly as galena and sphalerite respectively. This paper describes the development of flotation plant practice, aided by laboratory testing, to process the supergene ores. The major challenge in treating these ores is that a varying proportion of the sphalerite is naturally activated and is not easily depressed in flotation by the conventional zinc depressants.

Jan 1, 1991

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

This paper reviews the geochemistry of weathered nickeliferous sulphidic and lateritic profiles, the supergene behaviour of nickel and ore-associated elements, and their implications for exploration in an attempt to distinguish between barren and mineralised nickeliferous profiles. Nickel is an abundant accessory element in ultramafic rocks with background concentrations in some units up to 0.25 weight per cent. Ore-grades in fresh rock are mostly associated with massive and disseminated sulphide zones within magnesium-rich layered ultramafic sequences. In lateritic weathered terrain, nickel is also concentrated in the regolith profile. This process not only upgrades nickel in the gossanous weathered product of sulphidic deposits, but for sub-economic sulphide zones and some ultramafic rocks, is sufficient to result in a supergene resource. Ore-grade accumulations of nickel in regolith after sulphide-poor ultramafic rocks are referred to as lateritic deposits. Nickel sulphide zones and their ferruginous weathering products are collectively referred to as sulphidic deposits and are the major source of nickel in Western Australia. Mineral exploration in the Yilgam Block is hampered by deep lateritic weathered profiles (eg Butt and Sheppy, 1975; Smith, 1977; 1982). During the nickel boom of 1967 - 1972, most discoveries resulted from the location of outcropping nickeliferous gossan and ironstone. Exposed ultramafic terrain with nickel sulphide potential were explored intensively, mostly by gossan and soil sampling. However, up to 85 per cent of the area of the Yilgarn Block is buried by transported regolith. In these covered areas, barren and mineralised rock responses at the surface are similar and soil sampling produced unreliable results due to many false anomalies. A statistical, multi-element approach to regional geochemical exploration has evolved. Potential trace element indicators investigated, include Co, Cr, Cu, Ir, Mn, Pb, Pd, Pt, Sc, Se, and Zn. In recent years, trace element ratios have also been tested with varying degrees of Success.

Jan 1, 1996

Valuers will often intuitively express the probability that property value will exceed a certain amount . . . 'I think the chances that the value will exceed $50 million are excellent. The chances that they will exceed $80 million are poor'. This paper shows how it is possible to combine the uncertainties of the value of several key items to provide an estimate of the probability of a certain overall value being achieved. The valuation of a large copper/gold deposit was naturally influenced by uncertainties in the base assumptions of costs and metal prices. Potential acquisition of the property through share purchase raised the issue of what was a reasonable intrinsic value for the shares. Market considerations could be used to appropriately adjust the intrinsic value. After a range of possible metal prices and operating costs were determined, estimates were made of their probable distributions. By combining these probabilities in a random selection, a range of property values was calculated. Each value had its respective probability of occurrence. This allowed a most likely value of shares to be calculated. This paper demonstrates how the valuer's intuition is complemented by numerical analysis.

Jan 1, 1994

By Skinner J, Brackenbury K

The AuPlus" Systems have been applied in the gold mining industry to achieve improved gold recoveries, faster leach kinetics and reduced cyanide consumptions. Calcium or hydrogen peroxide, collectively known as peroxygens, can be used. The choice depending on plant design and the nature of the ore. Laboratory test work and plant trials are included in this paper to illustrate the benefits of peroxygen usage in extractive gold metal- lurgy.

Jan 1, 1991

By Johnson G. D

The typical management systems used to address the issue of operating risk centre around technologies that identify, analyse and evaluate the risk factors. These logical systems such as HAZOPs, Fault Tree Analyses, etc rely heavily on technical considerations and process flow analysis. However, several research projects, across industries and countries have clearly shown that up to 80 per cent `operating risk' is determined by the actions of workers, supervisors and managers. Yet, most of the focus of risk management is on technical and procedural issues. This suggests that a significant imbalance exists in our management systems and that industries are unlikely to show significant improvement on current levels of safety performance. Effective risk management must include the intangible element of the organisation psychology towards risk. A practical and theoretically sound approach had been researched and developed in and for the mining industry. This paper describes the approach and methodologies applied at the Cosmo Howley Gold Mine in the Northern Territory, where an inclusive approach to managing financial and operating risk was followed. The Cosmo Howley Mine showed a dramatic reduction in lost time injuries and improvements in financial indices - providing conclusive evidence of the link between management effectiveness, safety and productivity. This `triangle' has often been the subject of speculation and theory. It is demonstrated in this paper how the management team of Cosmo Howley focused their practices and systems on the improvement of organisational dynamics, ensured tangible and clear focus on parameters of costs and safety and how the improvement process was managed. It is concluded that the improvement process did not require a `major re-engineering' of the organisation. The organisation culture changes that occurred were incremental, planned and effective. It entailed the implementation of sound risk management methodologies, and ensured that a significant emphasis was placed on an aspect that is defined as `organisational dynamics'.

Jan 1, 1994

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005

By Standish N

The heterogeneous reactions of carbonaceous materials with oxidising gases are basic to all combustion phenomena and to many gasification processes. The carbon- carbon dioxide reaction at elevated temperatures (Reactivity) plays important roles in many metallurgical operations like iron blast furnace and ferro-alloys smeltings, zinc and lead smelting, alumina reduction, cupola operation and direct reduction processes. The stoichiometry but not the mechanism of the reaction between CO2 and carbon is represented by the equation (Boudouard reaction) CO2 + C 2CO (1) This reaction is more complex than that between carbon monoxide and metal oxides, which involves essentially a transfer of oxygen from the oxide to carbon monoxide to generate carbon dioxide without any change in gas volume, whereas the volume of the product gas of Equation (1) is twice that of the reactant gas. In the present paper an attempt has been made to review critically the reactivity measurements of various carbonaceous materials in carbon dioxide atmosphere. Steps in C-CO2 reactions, surface reaction mechanism, role of mass transfer on reaction kinetics, dynamic oxygen exchange reaction and rate equations and rate controlling steps are discussed. Various methods of reactivity measurements with their pros and cons are also presented. Effects of pertinent process variables on the reactivity of carbon are also described in detail.

Jan 1, 1986

Mineral resource and ore reserve classification defines the risk associated with quoted resource tonnes and grades, allowing the interested party to make a judgement as to the `worth' of the resource statement. The JORC Code and Guidelines (1992) are now well entrenched as the foundation upon which gold and base metal deposits in particular are publicly reported. There are three categories of resource, namely Measured, Indicated or Inferred reflecting decreasing levels of confidence. The ore reserve, that is the economically mineable part of the resource, is classified as Proven or Probable and can only be drawn from the Measured and Indicated resource categories. As summarised by Stephenson (1995), resource/reserve classification has been an issue ever since the earliest days of mining in Australasia where, like elsewhere in the world, the industry, for a long time, lacked firm reporting guidelines. Those currently adopted in Australasia as the minimum standards for companies reporting to the Australian Stock Exchange (ASX) have been developed and revised since 1972 by The Australasian Institute of Mining and Metallurgy (The AusIMM), the Australian Institute of Geoscientists (AIG) and Australian Mining Industry Council (AMIC). Debate is now underway in terms of adopting an international code. The Code specifically does not attempt to regulate either the classification technique nor the method of estimation of the resource/ore reserve, but rather places the responsibility for this task on a `Competent Person' whose experience will decide the appropriate approach for a given commodity/orebody. The Competent Person must be a Corporate member of either The AusIMM or AIG with five years experience `relevant to the style of mineralisation' under consideration.

Jan 1, 1996

By Caigen Wang, Wending Ma, Xiexin Mi

The urgent need for the control of surface subsidence caused by longwall coal mining in densely populated areas of China has led to a feasibility study on the effectiveness of longwall goaf cemented backfill. The study is focussed on exploring the potential of longwall goaf cemented backfill practice for surface subsidence control. Specific backfill geometry was designed in view of the characteristics of the longwall coal mining system. Laboratory physical simulated tests were carried out with different backfill material properties and pack size. The tests achieved a marked reduction in surface subsidence by the use of goaf cemented backfill. The system has been shown to be effective in laboratory tests, the challenge now is to overcome the engineering problems to put it into practice.

Jan 1, 1998