Search Documents

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

By S E. Box, J L. Mauk

The Middle Proterozoic metasedimentary rocks of the Belt Supergroup contain important metallic mineral deposits like the diagenetic sediment-hosted stratiform copper mineralization, including the Troy (Spar Lake) deposit and the epigenetic hydrothermal veins in the lower Belt and Ravalli Group in the Coeur d'Alene district. Magnetite (Fe3O4) is a common and widespread accessory mineral in these rocks and can have multiple origins including ore stage in deposits, mobilization stage in source rocks, metamorphism of red beds and alteration mineral in thin halos enveloping Ag-rich veins in the Coeur dÆAlene district. As shown in several classic studies, the composition of magnetite from igneous rocks varies significantly in response to controlling factors such as melt composition, temperature, silica activity, and oxygen and sulphur fugacity. Therefore, the distinctively different geologic settings within the Belt Supergroup strongly suggest that there may be differences in the magnetite compositions. However, initial microprobe analyses detected no variation in magnetite composition.   Three possibilities may give an adequate explanation for these initial results: 1.      the magnetite formed primarily as pure Fe3O4, 2.      one or more tectonothermal events led to regional scale re-equilibration that affected all rocks in the field area, and 3.      the variations in the composition are below the detection limit of the microprobe.

Jan 1, 2007

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By Watson D. F

Armstrong's (1983) criticisms of PhiIip and Watson's (1982b) note on optimal drilling patterns are based on misinterpretation, supported by errors in geometry. Furthermore, Armstrong argues conceptually from the perspective of Matheronian geostatistics, as does also Rudenno (1983a, b). Thus, both authors embrace a global, probabiIistic method of assessing spatial data sets, an approach that must be contrasted strongly with local, deterministic interpolation methods. Some of the important assumptions of geostatistics are outlined and the non-unique nature of the method discussed. A probabilistic approach can be judged appropriate when exploration data are erratic, or known to be unreliable, or when extrapolation is desired. Where data are treated as exact, kriging can give the most biased result if tested against other interpolation methods. We reiterate our previous conclusion that the equilateral triangular grid is approximately 30 per cent more efficient (in terms of numbers of drill holes) compared with a square grid for the same maximum interpolation distance. This is simply due to the improved isotropy of sampling. New, locally-based, deterministic methods for computing ore reserves seem to be required.

Jan 1, 1984

In contrast with mining in areas close to the main centres, mining in remote areas is characterised by comparatively high initial investment and relatively high running cost for the life of the mine. This is because of:the real cost of establishing and running the operation at a location distant from the necessary infrastructure; and the perceived risks priced into their costs by the multitude of suppliers involved in the project. Optimal co-operation between the mine and the supplier in developing the right rela tionship and the correct technical solution permit both cost elements to be reduced. This re duction may well mean the difference between success and failure. This paper examines the possibilities for optimising the contribution of the equipment supplier to the overall success of the process. Issues covered include the necessity to provide more than merely equipment fit for the purpose , but also the need to maximise the benefits of equipment ownership over the life of the mine. A simple method of determining the optimum timing for equipment replacement or rebuilding is proposed . Furthermore the maintenance contract (or performance agreement) is suggested as a means of leveraging the supplierÆs commitment to the mining operation. The specific examples are based on experience with mobile equipment but the methodology has relevance to other equipment and supplies.

Jan 1, 1998

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

By Dunne R, Defilippi J

Dump leaching began at Teller in late-1988 at a rate of 4 MTPA and has been progressively expanded to the present rate of 10 MTPA. Teller's on-going commitment to dump leaching is driven by the amenability of gold ores to the process and the availability of large tonnages of low grade gold ore. The sequence of evaluating ores for dump leaching involves rolling bottle tests on coarsely ground ore, followed by small and large column leaching and finally trial heaps. Trial heap tests are very expensive and an alternative approach to this is large diameter column leaching.A four-column permanent facility was built at Teller to specifically evaluate the leaching characteristics of new dump leach ores. Details of construction, operation and dismantling are discussed in the paper. Capital cost for the four column facility was some $45 940, while operating costs are about $24 800 per column.

Jan 1, 1992

By Linge H. G

The effect of the presence of ore pulp on the adsorption rate of gold on activated carbon has been studied. A substantial reduction in the rate occurs when the pulp is present. The reduction in rate appears to be caused by two effects: permanent carbon pore blocking by ore particles and temporary shielding of the carbon particle surface, slowing gold access to the carbon due to the physical presence of the fine pulp. There is no significant effect arising from the presence of a pulp viscosity modifier even for conditions when mass transport dictates the loading rate of carbon in clear Solution.

Jan 1, 1987

WITH the exception of the deposits of the Milburn Cement Co near Dunedin, Wilson's Portland Cement Co., on the Mahurangi River (a short distance north of Auckland), and those of the New Zealand Portland Cement Co., at Limestone Island, the cement. Tesources of New Zealand remain practically undeveloped. The Milburn Company utilizes a mixture of limestone and mud for the manufacture of cement, while Wilson's and the New Zealand Portland Cement companies both have the advantage of a natural cement stock which requires but small additions of highgrade limestone to give the mixture required. The plant and deposits of the New Zealand Portland Cement Co are located in Whangarei Harbour, some six miles from thetownship of Whangarei. The works and dwelling-houses are situated on Limestone Island, which, with an area of 92 acres, and rising to a height of 212 ft., supplies the bulk of the raw material required. In addition to the island, the company possesses a high-grade limestone area of, roughly, four acres, situated on the mainland, 11 miles to the south. A better location for a cement works could not well have been chosen. On the east side of the island there is a deep channel, which never shows less than 18 ft. of water alongside the company's...

Jan 1, 1911

Exploration by Cyprus Minerals Australia Company (formerly Amoco Minerals) has successfully outlined significant Au-(Cu) mineralisation at Starra, 150 kilometres south-east of Mt. Isa. Mineralisation is stratabound and localized in deformed and metamorphosed ironstones (B.I.F?) and iron-oxide bearing schists of the mid-Proterozoic Staveley Formation. Over 90% of the presently outlined potential ore occurs in 4 discrete zones within a strike length of 3.5 kilometres. The inferred geological resource in these zones is approximately 6 million tonnes grading 5 grams per tonne gold and 2% copper. Roughly half of this is open-pittable, but more rigidly applied mining criteria will probably reduce the exploitable tonnage. Detailed infill drilling is in progress and a pre-feasibility study has commenced. The joint venture partners, Cyprus Minerals (75%) and Elders Resources (25%) expect to make a development decision by the end of this year.

Jan 1, 1986

By D R. Lueking

A technology involving separate unit processes for the generation and use of ferric ions for the oxidation of sulphidic minerals has been developed. The technology utilises a stand-alone automated bioreactor for ferric-ion generation (termed SAAB-FIG) and produces a low pH, ferric ion-rich leach liquor with a high oxidation potential. This leach liquor is then employed, in a separate unit process, to oxidise sulphidic minerals and regenerate ferrous iron that may subsequently be recycled to the bioreactor for the continual generation of ferric ions. The technique was successfully applied for the recovery of copper from chalcocite (Cu2S) and chalcopyrite (CuFeS2), as well as other ores and concentrates containing copper sulphide minerals. Coarse ore, ground ore and concentrates were treated with acidic solutions containing 8 to 12 (g/L) Fe(III) ions at a variety of temperatures. This process yielded over 50 per cent of the contained copper from both chalcopyrite and chalcocite samples. Maximum reaction rates and copper recoveries were found to be highly dependent upon temperature and pH and leach liquors containing bacterial cells displayed little difference in their leaching efficiency when compared to cell-free leach liquors.

Jan 1, 2000

This paper gives the background to the development of solvent extraction processes for the recovery of metals from aqueous solutions. Its growing importance in Australia for the recovery of both uranium and copper is dis- cussed, as well as the developments in mixer-settler design as applied to recent plants. The economic significance of solvent extraction as an alterna- tive to cementation is discussed and important features of each process are highlighted by comparison of costs for each process in a hypothetical situa- Tion.

Jan 1, 1971

By Channon W, Dube M, Makwana M, Kerfoot D. G

In early-1995, the Bindura Nickel Corporation commissioned a pressure leach plant at its Smelter and Refinery complex located in Bindura, Zimbabwe. The novel pressure leach process was developed by Sherritt to treat the nickel-copper sulphide residue produced from the original atmospheric leach circuit. The process extracts essentially all the nickel from the nickel-copper sulphide residue under non-oxidising acid pressure leach conditions, thereby producing an upgraded copper sulphide residue suitable for smelting and refining to electrolytic copper. The commissioning of the pressure leach plant was relatively smooth and design conditions were achieved within six weeks of operation. This paper presents a brief description of the process development and the plant design, followed by highlights of the plant start-up activities and summary of the plant performance.

Jan 1, 1996

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

In recent years there have been a number of excellent towns built for mining communities in remote parts of Australia. Planning has been thorough, and very large capital expenditures have been made by companies to provide high standards of accommodation, services and amenities. But so often the phrase 'company town' comes to be applied, expressing the frustrations of the residents, working for a single employer who dominates their lives, and of the company, which would prefer not to have to build and operate a town. The much-vaunted early success of some iron ore, bauxite and coal projects has led to a belief that the success of all mining projects is assured. Those holding this belief ignore the vagaries of mineral deposits and of markets, and the need to amortise large high-risk capital expenditures, much of which is spent on social and industrial infrastruc- ture. This expenditure on infrastructure does not have to be

Jan 1, 1975

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

During mapping in the Bijerkerno area (Fig. 1), well-preserved sedimentary structures were found at three separate localities. The structures are of four varieties, which are 1. small-scale cross-bedding (Fig. 2),2. convolute bedding (Fig. 3),3. minor scour and fill (Fig. 4), and4. flame structures.Ripple-marking is also doubtfully present.These structures are best preserved in what was...

Jan 1, 1971

By J Herbertson

æZero waste steel making productionÆ has already been the subject of several studies and also the successful result of some companies. Regarding waste and by-products, slags are the largest in terms of weight, although among the least hazardous. All steelmakers around the world are presently looking into profitable solutions, according to their local conditions: environment constraints, available markets, and mode of operation. Today the major technical methods of slag value capture include different levels of magnetic separation and screening to remove entrained steel, for production of aggregate in civil works. A survey of different retrieval processes shows that pyrometallurgical processing of steelmaking slags will increase the recovery ratio of iron and other metals. In the process, the remaining part of the material, a mixture of metallic oxides, can be easily transformed into hydraulic binder such as cement. Can steelmakers consider the slag as a co-product, and not only a waste or by-product? The ability of pyrometallurgical processes to treat other wastes and by-products generated in the steelplant is an opportunity for the steelmakers to reach the æzero waste productionÆ status. A technical survey of the experiences and possible solutions of pyrometallurgical processing is presented as well as technical descriptions of technological, economical and profitability analysis in relation with foreseeable markets.

Jan 1, 2002

The city of Kalgoorlie-Boulder is located 595 kilometres east of Perth in Western Australia, and has a population of just over 30 000. Western Australia's third largest city lies on one of the richest goldfields in the world, with over 45 million ounce

Jan 1, 1998