Search Documents

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

By D W. Wall, J P. Vagenas

Questions of sampling precision and accuracy affect every process plant in differing ways and to differing extents. To address these perceived issues, chemists, metallurgists and engineers are often asked to check their results to confirm their reliability. However, it is not possible to achieve the level of detail required to check every sample, especially if the event has already occurred. No operation has the resources to frequently sample every point in the process for the purpose of verification.One way to address this scenario is by generating a sufficiently detailed comparative data set from a dynamic mass balance simulation of the processing plant. This mass balance uses both sample and plant instrument data to model every flow, while also taking inventory changes and process chemistry into account.The mass balance data can be used to identify any bias present in plant sampling and analysis. It can also be used to verify any unexpected assay results by taking a holistic view of the process. Improving the precision and accuracy of sampling data helps support operational decision-?making and understanding. It also improves the accuracy of the dynamic mass balance used in this process, facilitating further improvements.CITATION:Vagenas, J P and Wall, D W, 2017. The benefits of automated metallurgical accounting for plant sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Determining the controls of high-grade mineralisation at Vera Nancy requires careful data collection and assessment on a global and specific deposit basis. The techniques developed over 60 years ago to analyse structure, grade and width data are just as applicable today and can be enhanced using modern geological modelling software. High ore grades at Vera Nancy are controlled by both the primary geometry of the mineralised structure and the intersections of the main mineralised veins with subordinate splay veins. The main mineralised structure dilated as a consequence of extensional tectonics while the splays acted as conduits bringing oxidising surficial fluids into mixing zones precipitating high gold grades. Near-mine exploration is focussed on identifying zones of vein flexure and splay interaction to locate the relatively small high-grade shoots. Data modelling in a 3D environment is an essential process for understanding the geometry of the system being explored.

Jan 1, 2000

By M Dusci, A Trueman, S Poos, R Baumgartner, M Brittan

The Canahuire epithermal Au-Cu-Ag deposit in southern Peru is a complex and challenging deposit for metallurgical studies. It has issues of gold locking in sulfides and non-sulfides, deleterious elements and acid rock drainage (ARD). From scoping study to feasibility study, there has been considerable improvement in the understanding of the important geometallurgical characteristics that need to be measured and modelled. This paper presents the current understanding and the requirements to continue to provide optimal models for mining studies.Significant effort has been put into understanding the genesis of the deposit. Improved spatial and temporal understanding of lithology, alteration, structure and mineralogy was used to build a geological and alteration model of the deposit.Early metallurgical programs quantified the effect of head grade on process plant recoveries, but the geometallurgical and statistical analyses did not identify other physical characteristics that influence these recoveries. The studies improved the understanding of the nature of locked gold which can occur as minute inclusions (< 5 ¦m) in sulfides (primarily pyrite with lesser arsenopyrite, pyrite being 100 times more abundant than arsenopyrite) and gangue minerals (quartz and carbonates) as well as solid solution in arsenopyrite and pyrite.The presence of pyrite and the limited buffering capacity of waste rocks increases the potential ARD, which will require mitigation costs before, during and after operations. Waste rock ARD potential has been classified and incorporated in the geometallurgical model. The current classification of waste rock at Canahuire, using international classification standards, is limited due to the complexity of the deposit.Complex deposit metallurgy necessitates a complex process flow sheet, including flotation and cyanidation. Economic recovery will be constrained by the relationships between economic variable grade, other elements and mineralogy. These constraints and inter-relationships are difficult to establish throughout the deposit with a single test. A follow-up geometallurgical program is under investigation and will attempt, with the help of additional test work, to map areas of higher and lower recoveries. It is hoped that metallurgical response can be linked to measurable parameters other than head grade. If this is possible, these factors can be incorporated into future geometallurgical models.CITATION:Baumgartner, R, Dusci, M, Trueman, A, Brittan, M and Poos, S, 2013. Building a geometallurgical model for the Canahuire Epithermal Au-Cu-Ag Deposit, Southern Peru - past, present and future, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By G Zhang, I Glacken

Multiple indicator kriging (MIK) has been used in the minerals industry for some decades. As one of the non-linear estimation methodologies, MIK has advantages related to resolving multiple or mixed populations, high variability data and strongly skewed distributions. Applying the MIK methodology requires a lot more effort when compared to other non-linear methodologies, for example localised uniform conditioning. This is due not only to the variogram modelling for multiple indicators, but the validation is also very important because the panel model is fundamental for follow-up work, including the generation of recoverable resources at the local or SMU scale. Apart from this, only a few reported case studies of MIK have documented post-processing of the estimated modelled distribution, representing the probability distribution at point scale at un-sampled locations. The MIK post processing should include the change of support from the point scale to the panel scale, and then the extraction of quantile values from the panel conditional cumulative distribution function (CCDF) for localisation of grades into the SMUs within each panel, based on a ranking estimate marking the SMUs from high to low. In this paper, we present a case study on a gold deposit with the MIK method with full-post processing implemented for recoverable resources. The MIK point estimate was carried out with an indirect lognormal change of support from point to panel scale, and localisation was done with a custom script. The localised uniform conditioning (LUC) method was also applied for comparison purposes. The comparison shows that MIK has advantages compared to LUC when comes to capturing the high-grades, especially when mixed or varying anisotropy is present within the mineralisation.

May 24, 2023

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

By M Darvall

Magnetite ore blending has yielded signifi cant performance improvements in OneSteel’s magnetite concentrator. The magnetite concentrator beneficiates magnetite ore from the Iron Magnet Deposit and produces concentrate, which is pelletised, then fed to the OneSteel Whyalla blast furnace. Concentrator feed variability severely detracts from the concentrator’s performance, affecting both concentrate yield and grade, which impacts on all downstream processing costs.A coordinated approach has integrated mine planning, geological modelling and grade control, to minimise concentrator feed variability, through effective ore blending throughout the mining and stockpiling process.Mine planning personnel design shots that extend the full width of the orebody and hence across the stratigraphic profi le. Based on geological information contained in block-outs and in consultation with Geology, the Grade Control team allocates material to each primary stockpile, potentially from every stratigraphic domane in the orebody. This ensures primary stockpiles are designed with maximum practical homogeneity and consistency.Using only primary movement, the allocated ore is stockpiled in a layer-cake fashion. The ore is pimple dumped across the width of the stockpile footprint and on completion of a layer, it is dozed flat with an access ramp that allows dumping to commence on the next lift. The primary stockpiles are reclaimed normal to build direction and the magnetite is crushed, all in, to a concentrator feed stockpile.The ore is sampled at the crusher from a falling stream cut. These assay data, are used for benchmarking and control charting the grade and variability of concentrator feed stockpiles. The concentrator feed stockpiles have demonstrated a statistically signifi cant reduction of within pile variation, between pile variation and pile to pile variation, primarily attributable to the development of ore blending. The concentrator has seen sustained, improved performance as a direct result, which translates into lower concentrate cost per tonne and improved yield and quality.

Jul 11, 2011

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

By A Tawadrous, D S. Preece

Cave mining is of interest to the mining community as it offers a chance to extract large, deep orebodies with low operating costs and high production rates. It allows for extracting large low-grade orebodies, which may not have previously been considered for mining. Cave mining is done either top down (ie sublevel caving) or bottom up (ie block/panel caving). Both approaches rely on gravity, stresses and weakness of the rock to fracture and achieve a controlled collapse.Block caving starts at the base of the orebody. It progresses upward and across through continuous collapse of the roof. To achieve this, a critical hydraulic radius must be exceeded. This is accomplished by blasting drawbells, through which the caved ore passes to the production level. An entire level above the drawbells (undercut level) is excavated to help initiate the cave. The undercut level ensures the connection between drawbells and achievement of the required hydraulic radius.Conventionally, drawbells are generated by drilling and blasting several times from the production level as well as the undercut level. Mucking between each shot is required to generate enough void space for the rock to swell. The need for several blasts necessitates some downtime between each blast. Also, the cost of developing and maintaining the undercut level can constitute up to 35 per cent of the cost of mining the panel.A new blasting technique was developed to create the drawbells in a single blast from the production level. The technique ensures the connection of the drawbell to the neighbouring ones, thus, the critical hydraulic radius is reached and propagation of the cave achieved without the need for the undercut level. The technique has the potential to reduce the capital cost of a block caving operation, increase its feasibility and reduce time to reach the ore and consequently the payback period. This paper presents the modelling of a traditional drawbell excavation process, the philosophy of the developed technique, the modelling of that new design and its implementation.CITATION:Tawadrous, A and Preece, D S, 2015. A novel blasting technique to create drawbells and eliminate the undercut level in block cave mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 617–624 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Suzuki

Although several models for the surface tension of molten oxide slag have been proposed, suitably accurate predictions of this property are not yet possible. The surface tension, or surface excess free energy, of molten oxides is largely determined by the ionic coordination induced by surface relaxation. However, the associated mechanism of surface structural relaxation for molten oxide mixtures such as slag is complex and not yet fully understood. To allow a better evaluation of surface relaxation characteristics, the present work analysed the ionic coordination associated with the surface-relaxed states of several oxide mixtures. This work especially focused on calcium aluminate slags because these materials exhibit complex relationships between composition and surface tension. The effects of incorporating low concentrations of SiO2 as a surface active component on the surface ionic coordination were also examined. X-ray absorption techniques were used to assess oxygen and cationic elements in glassy samples after surface relaxation treatments, and molecular dynamics simulations based on a polarisable ion model of molten slag with vacuum/melt interfaces were also performed. The X-ray absorption techniques provided data related to electron yields (which are primarily associated with surface features) and fluorescence yields (which evaluate the bulk material). Thus, the ionic coordination characteristics of both regions were investigated. The results of molecular dynamics calculations allowed statistical analysis of the distributions of Al- or Sicentred polymorphs as well as the bond angles between cations and oxygen anions in the vacuumexposed and bulk regions in the equilibrated melt. The results indicated that bridging oxygen ions were preferentially distributed in the relaxed surface region rather than non-bridging oxygens. These bridging oxygen ions represented vertex connections between AlO4 or SiO4 tetrahedra. In the case of the calcium aluminate slags, the addition of one Ca2+ ion as charge compensation for two Al3+ ions was found to be necessary to form two AlO4 tetrahedra. This specific feature of surface ionic coordination could be responsible for the complex trends observed in surface tension data. The incorporation of low concentrations of SiO2 reduced the proportion of tetrahedrally-coordinated Al ions such that higher coordination states become dominant in the bulk of the material, whereas AlO4 tetrahedra were preferentially distributed in the surface region. SiO4 tetrahedra were the preferred Si-centred polymorph and were likely connected to one another to form bridging oxygen ions at the surface. On the basis of these results, a model to predict slag surface tension was proposed, and the energy of the formation of the ionic clusters resulting from surface relaxation was taken into account.

Aug 21, 2024

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

Current NSW Government policy requires searching for more than just minerals during an exploration program - add endangered fauna and archaeological relics for a start.

Jan 1, 1995

This paper looks at the development in management education for engineers at the undergraduate level with particular reference to mining engineers. The management core content of the engineering degree course at Ballarat C.A.E. is described is some Detail.

Jan 1, 1986

In 1952 when universities imposed fees on students and most students won either Commonwealth or Government department or private scholarships to study, I won a scholarship to study mining engineering at the University of Technology in Sydney. The univ

Jan 1, 1994

By Mukherjee R, Bandopadhyay S

Three applications of fuzzy logic in mineral exploration show the possibility of providing feasible solution and allow greater freedom in decision-making processes for geoexploration data which may be ill- defined, biased or where apriori infor

Jan 1, 1998

I will confine my remarks to normal computers that people interact with, rather than built-in processors which exist in every watch and washing machine these days. I will also confine myself to computing in the technical side of mining. Bu

Jan 1, 1998

Jan 1, 2004

Mineral resource and ore reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential hazards and pitfalls are to be avoided however, there are two other requirements which are of equal, if not greater importance:

Jan 1, 1990