Search Documents

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

The elements of consistent structural de sign models for underground structures are explained. Such models should comprise at least ground properties, excavation and support methods, computational models for analysis, failure hypotheses, and in-situ monitoring. The fundamental characteristics of the interaction between ground and support are investigated. Then, plane strain models for soft ground tun- nelling and design models for rock tunnelling employing stress release at the tunnel face are elaborated. Some numerical evaluations are gi- ven in diagrams, comparing approaches of dif- ferent authors. Comments are presented on nume- rical three-dimensional models (visualized by structural models for mining in rock salt), on the interaction of in-situ monitoring and design, on structural safety for underground structures, and finally on the general develop- ment of structural design models in geo- Techniques.

Jan 1, 1987

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

By Collins M. J, Ozberk E

A major advantage of the Sherritt Zinc Pressure Leach Process is the conversion of sulphide sulphur in zinc concentrate to elemental sulphur during pressure leaching. Elemental sulphur can be recovered as a marketable byproduct by flotation of the leach residue, and melting and filtration of the sulphur flotation concentrate. The behaviour and deportment of sulphur during pressure leaching, flotation, and melting and filtration are discussed in this paper using data obtained from the treatment of a wide variety of zinc concentrates in the laboratory miniplant at the Sherritt Research Centre. The quality of the elemental sulphur byproduct and a process for purifying the sulphur are also Presented.

Jan 1, 1993

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

Numerical simulation by a finite element computer code has bee* used to identify key stages in the initiation of confined bulk explosive by cast primers. The simulations have been verified by comparison with experimental field measurements of shock arrival time versus distance above the primer for a relatively sensitive emulsion doped with ammonium nitrate prills. Further simulations were performed examining the effect of primer size in a relatively insensitive blend of ANFO and emulsion. Immediately above the primers, changes in shock velocity in the explosive were caused by the interactions between shocks originating from different surfaces of the cylindrical primers. At a distance up the explosive column corresponding to about one to two borehole diameters, the arrival of shock reflections off the borehole walls caused a sudden acceleration up to the confined steady state detonation velocity. The simulations reproduced experimental observations that primer size has only a weak effect on changes of shock velocity with distance for confined explosives. However, it was predicted that primer size has a strong influence on the intensity and duration of the pressure pulses that bulk explosive send into the rock surrounding the primer region.

Jan 1, 1990

Nickel WestÆs Kalgoorlie Nickel Smelter operates three Peirce-Smith converters, each processing 110 tonnes of matte per charge. The vessels are lined with chrome-magnesia refractory with a mouth traditionally constructed from steel liner plates, protected with cast refractory. Mouth refractory is damaged by molten material and the action of cleaning solid buildup off the mouth. Once damage has accumulated, the mouth must be frequently maintained with hot refractory gunning or a mouth leak may occur. Such a leak requires a 32 hour repair period. A converter mouth redesign program was undertaken with the aim of reducing the rate of mouth damage during operation, eliminating mouth leaks and shortening mouth replacement times during vessel rebuild periods. An overview of the redesign process and operational performance is contained herein.

Jan 1, 2005

By Blight P

There is today widespread concern about the future of the mining industry. In attempting to understand the underlying causes the paper probes in some detail, the long term structural changes affecting growth of metal demand and the development of excess mineral supply capacity. This examination reveals an industry characterised by an unfavourable combination of high barriers to exit and low entry barriers. While rising entry barriers are expected to herald some improvement in the profitability of mining over the next decade, this adjustment is likely to be slow and will require a more economically rational assessment of the industry by corporations and governments Alike.

Jan 1, 1986

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

By Dickin FJ

Advances in the development and application of in situ imaging of mineral processing operations using electrical tomography techniques are reviewed and illustrated with case studies relating to pneumatic conveying, mixing and centrifugal separation processes. The potential for applying these methods to full three-dimensional visualisation of the dynamic behaviour of flow in pipelines and separators, and the resulting consequences for process-modelling strategies, are discussed.

Jan 1, 1993

By Regan R

Appin Colliery mines the Bulli Seam with a gas composition of 98.5% methane and 1.5% carbon dioxide. Relaxation of the strata generally occurs to below the base of the Wongawilli Seam, some 40 m below the Bulli Seam, and approxim- ately 125 m above the Bulli Seam, for longwall face widths of 135 m or more. Previous exper- ience showed that when longwall faces were mined for a distance approximately equal to the face width, the mine ventilation could not provide sufficient dilution due to methane emissions from the underlying measures. Postdraining downholes were drilled to intersect the Wongawilli Seam below the operat- ng longwall. These holes were connected to an underground to surface gas range and various suction levels were applied to improve gas drainage. The resulting gas flow rates and purity from all the downholes were regularly monitored and peak flows in some holes exceeded 160 1/sec. The surface plant drained almost 20 million m3 of gas for the period July 1981 to January 1982 at an average methane purity of approximately 70%. Distinct patterns emerged for different downholes from curves illustrat- ing their variations in flow rate with distance subsequent to passage of the longwall face. The difference between free flow characteristics and those obtained with the application of

Jan 1, 1982

By Haslam C. O, Los V. L, Abramson G. J

The technology applied by lonex Pty Ltd provides an important breakthrough in geochemical exploration, enabling the discovery of concealed mineral deposits to great depths below surface. Most mineral discoveries have been made in areas of outcrop or relatively shallow cover; deposits at greater depth have been beyond the range of conventional geophysical and geochemical methods. Quite apart from the need to explore to greater depths in regions of major current or past production, most continents have vast areas where prospective host rocks are concealed by more recent material. There are numerous case studies where Ionex methods have located deeply-buried metal deposits, up to 500 m below surface, beneath thick younger sedimentary, volcanic, or transported cover. Research leading to the development of this technology was initiated by Dr I S Goldberg at the Rudgeofizika Institute in St Petersburg (CIS), and the methods have been employed there - and in other countries - for many years. Ionex technology became available in Australia in 1993. It comprises: ò geochemical and geoelectrochemical sampling and ultra-high-sensitivity analysis for mobile and weakly-bonded elements (I S Goldberg); ò the delineation and interpretation of regional zones of enrichment and depletion of the prime elements within geoelectrochemical systems (GES) (I S Goldberg); ò the investigation and interpretation of the three-dimensional geochemical zoning within geochemical anomalies (G J Abramson); and ò multi-variate computer modelling of the geochemical fields and systems (V L Los). lonex technology has been adapted to the environmental conditions in Australia with the participation of C 0 Haslam.

Jan 1, 1997

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By Ramani R. V

In this paper, a comparative performance evaluation of geostatistical, spectral, and fractal methods is made for short-scale variability prediction. The algorithms compared are: sequential Gaussian simulation method; a random fractal algorithm based on the generalised stochastic subdivision method; and a spectral simulation approach adopted for direct multi-dimensional simulation. The data for this study have been obtained from a mined out coal property. As this property was being mined, a 7315 m by 7315 m (24000 ft by 24000 ft) coal block was extensively sampled at an approximate spacing of 107 m (350 ft) and the 60-ton samples were analysed for sulphur in the 1.50 float gravity fraction. This data set is used here with the three methods to generate the simulated realisations, which are analysed for semivariogram reproduction and for simulation errors. Although all three methods converge to the true semivariogram in an average sense, the coefficient of variation of the average semivariogram for the Fourier integral method is minimum. The realisations generated by the sequential Gaussian method have minimum mean simulation error. The choice of a simulation method based on variability reproduction and simulation errors remains difficult.

Jan 1, 1995

Until early-1997, Mount Isa Mines Limited (MIM) generated electrical power for most of north-west Queensland. The discoveries of many new orebodies in the region meant the inevitable increase in power generation requirements for the new mines. In addition, the expansion at Mount Isa itself meant that MIM had to invest in new generating capacity or utilise the existing generating plant more effectively. Using its generating plant more effectively required MIM to undertake rigorous energy management within its own operations. A personal computer based system with a wide area network was installed as the basis for energy management. The result was that energy consumption was reduced, the need for additional generating plant was curtailed, and capital outlay for the generating plant that was required was delayed. As a direct result of energy management, carbon dioxide emissions were reduced substantially.

Jan 1, 1998

By Waqinwright M. S

The underlying principles of dewatering theory have recently achieved considerable practical application in the washing and dewatering of alumina trihydrate in Bayer plants. In particular, the influence on residual cake moisture contents of trace amounts of surfactant added to the wash water reveals that significant energy savings can be achieved. The influence of organic compounds produced by the caustic extraction of bauxite in the Bayer process is shown to be significant. These humic species reduce the cake permeability and the effectiveness of certain surfactants in dewatering operations.

Jan 1, 1989