Search Documents

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

THIS paper deals with the handling of the various materials used in the 100-ton zinc plant at Risdon, and, in view of the magnitude of the works, the configuration of the ground covered by these works, the variety of the rnaterials used, and the large quantities, a very attractive and interesting subject is opened.The works are situated on the right bank of the River Derwent, about four miles above Hobart, the capital city of Tasmania. The Risdon works cover a space of 149 acres, the area being :3800 yards long by 2800 yards wide, and the elevations vary from 6 ft. above high-water mark at the wharf and foreshore to 163 ft. above high-water mark at the power station, these being the limiting points as regards elevation which are considered in this paper. Throughout the paper elevations are given in feet above high-water mark. Fig. 1 shows a general view of the works taken from the opposite bank of the River Derwent. The wharf is clearly shown, with SS Kekerangu loading residue; behind the wharf is seen the inclined conveyor leading to the cakine bin; further up the hill is the leaching division. No. 1 haulage runs to the left of this up to a point on the left of the power station, the large reinforced concrete building at the top of the hill. Below this is the cell room, the largest building on the plant. The roasting division, not very clearly seen, lies at the foot of the main stack, and the casting division lies to the left of this, between the leaching division and the cell room. A large wharf has been construl'ted alongside the works. This wharf is 880 ft. long and 60 ft. wide. It is capable of berthing large overseas steamers, as at low tide there is a depth of :30 ft. of water. The rise and fall of the tide at the wharf is 4 ft. 6in., and the river is navigable at all states of the tide. Just above the company's wharf...

Jan 1, 1923

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

The City of KalgoorlieBoulder is situated approximately 600 kilometres to the east of Perth, and as the major regional centre of the Eastern Goldfields, supporting a population of approximately 25 000. The formation of Kalgoorlie Consolidated Gold Mines in 1989 brought the existing operating entities adjacent to the city under common ownership and management. The Joint Venturers forming the management company are Homestake Gold of Australia and Gold Mines of Kalgoorlie (a Normandy/Poseidon company).This traditional underground mining centre has been worked since 1893, yielding 40.5 million ounces of gold ore with an average head grade of TEN grams per tonne. Historically the heart of the operation has been the famous Golden We located on the Eastern perimeter of the city, in the area known as Fimiston. The other significant operations that form KCGM are the Mt Percy Open Pit and the Mt Charlotte Underground Operation.

Jan 1, 1992

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

The Devonian Mount Morgan gold-copper deposit was situated on the western margin of the Calliope Volcanic Are assemblage, in the northern New England Orogen. Recorded production from commencement of mining in 1882 to mine closure in 1989 stand

Jan 1, 1994

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By Stanley I. M, Brett D, Dickson R

The Mt Lyell Mine, situated in Queenstown on the west coast of Tasmania, has a production history of more than 100 years. Previous mining activities have resulted in substantial modifications to environmental conditions at Mt Lyell and disposal of sulphidic waste rock across the lease has left a legacy of on-going environmental impacts including acid drainage (AD). In 1995 Copper Mines of Tasmania (CMT) was granted a mining lease Irons the Tasmanian State Government for redevelopment of Mt Lyell and indemnity from actions concerning pollution from previous occupation and use of leased land. The Environmental Management Plan (EMP) for the Mt Lyell redevelopment committed CMT to be responsible for waste rock dumps generated from their activities and to ensure that management is in-line with best practice environmental management principles. CMT commenced commercial production in December 1995 with sulphidic material from development of the underground Prince Lyell mine reporting to a single waste rock dump constructed according to a management plan developed in July 1995 and superseded by a management plan for extension in May 1997. The CMT waste rock dump currently has a total capacity of 220 000 m- and approximately 120 000 m3 of rock have been placed to-date. Material reporting to the dump is placed in a densely compacted state to a controlled surface profile. The dump is clay capped and a final revegetated soil layer placed on top. A rock pitched drain extends down to a wetland area in order to remove stormwater and minimise possible soil erosion on the revegetated sections. An integral part of the management plan for the waste rock dump involves characterisation of waste rock to identify geochemical rock types according to acid forming potential with provision for selective placement within the dump. High-risk materials are selectively placed and covered within the core of the waste rock dump, where possible, to control sulphide oxidation. Monitoring equipment has been installed in the waste rock dump by the Australian Nuclear Science and Technology Organisation (ANSTO) and an on-going monitoring program has been established to demonstrate the integrity of the dump cover as a barrier to the influx of atmospheric oxygen into the dump. The overall objectives of this program of work are to control the oxidation of sulphidic waste rock in the waste rock dump, minimise the risk of AD, prevent pollution of the aquatic environment and thereby demonstrate the integrity of the CMT waste rock dump management Strategy.

Jan 1, 1997

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

Roadheaders have had a chequered history in hard rock excavation in Australia since their introduction into the country in 1972. This has resulted in a poor reputation among both clients and contractors and subsequent reluctance to design tunnels and underground space around their performance characteristics.This has now changed because of the introduction into Australia of a new breed of Roadheader, the Mitsui. This paper sets out the history of development of the Mitsui range of Roadheaders. It describes the process which resulted in the introduction of this new machine, its performance to-date and the characteristics which have contributed to the success of the machine. The combination of these factors have led to a change in attitude to the use of Roadheaders in underground excavations.

Jan 1, 1993

This paper covers the key issues such as orebody geometry and grade, geotechnical data and metallurgical response. These must be considered in selecting a mining system for a new orebody. It then focusses on the advantages of open pit mining over underground mining particularly in the areas of costs, speed of development and safety. Environmental issues with waste storage is the only negative which emerges. Consequently, the majority of new large mine developments continue to be open pits. It is also demonstrated that underground mining continues to play an important role, particulary for high-grade deposits at depth. The impact on ore recoveries of recent developments in stabilised fill technology in underground mining is also highlighted. The importance of economics to the decision on mining method is continually emphasised as maximising orebody value should be the prime objective of this Work.

Jan 1, 1997

By Tozawa K, Nishimura T, Sasaki K

Liquidus surfaces in a part of the systems ZnO-PbO-Si02 and ZnO-"FeO"-SiO 2 were constructed by the quenching method. The ex- periments were carried out in air in the system ZnO-PbO-Si02. In the part investigated the primary phases were three ternary compounds (PbO.ZnOòSiO2, 2PbOòZnO.2SiO2 and barysilite), three lead silicates, Zn2SiO4 and SiO2. Iso- therms on the liquidus surface of each primary phase field were determined from 750 to 1300¦C. In the system ZnO-"FeO"-SiO 2 the experiments were carried out in an atmosphere of purified nitrogen. In the part investigated the primary phases were Fe2SiO4, Zn2SiO4 and Si02. Iso- therms on the liquidus surface of each primary phase field from 1150 to 1300¦C and the ternary eutectic (1130¦C, 15.9% ZnO, 48.2% "FeO" and 35.9% Si02) were determined.

Jan 1, 1980

By Torabi S. R, Daly C. R

Wind blast is the sudden movement of air displaced by the massive collapse of roof rock in underground openings and is experienced as a high velocity flow of air through adjacent workings. The initial flow in the outbye direction is often followed by 'suck back', that is a reverse flow of air towards the newly created void. As part of the Wind Blast Project, undertaken by The University of New South Wales, Department of Mining Engineering, a physical model was constructed. One of the functions of the laboratory wind blast model is to provide insight into the dynamics of the interaction between the falling strata and the air being compressed below. During a collapse, some air is expelled into the surrounding roadways while the remainder penetrates towards the top of the roof elements. In this paper two aspects of the rock mass properties which influence the phenomenon are considered: - Flow paths through the falling roof element, ie the permeability of the roof element; - Bed separation prior to the fall which introduces a void above the roof element. A series of tests was carried out utilising the physical model in order to investigate the relationships between the flow of air through the simulated roadways, the variations in gauge pressure above and below the falling roof element, and the acceleration and terminal velocity of the latter, all as a function of the flow paths through the roof element and of the extent of the void above. The results of comprehensive tests using the wind blast physical model suggested that the time history of outbye air flow in the simulated roadway comprises two distinct phases. a) A primary phase, characterised by a high velocity flow of air which exhibits a peak and corresponds to the period during which the roof element is accelerating. The peak air velocity is related to the acceleration of the roof element. b) A secondary phase, characterised by a residual air flow of a lesser velocity than in the primary phase and corresponding to the period during which the roof element is falling at its terminal velocity. The velocity of the residual air flow is directly proportional to the terminal velocity of the roof element. In a monolithic collapse of a roof element it was shown that the presence of flow paths in the roof element increased the air velocity in the roadway in both the primary and the secondary phases. The presence of an air-filled void above the roof element, on the other hand, influenced the air velocity only in the primary phase by increasing the peak air velocity. The overall duration of the process was however decreased as a result. 'plug type' collapses, where roof failure extends to the ground surface, potentially generate the highest peak air velocities likely to be encountered during wind blasts.

Jan 1, 1995

The Coal Corporation of New Zealand Ltd (CoalCorp) is the largest coal producer in New Zealand, with extensive properties in both the North and South Islands. CoalCorp's North Island operations are kilcmetres to the south of Auckland. opencasts, are located in the catchment wildlife, historical and scenic values. in this catchment is the single most mining operations. centred on Huntly, a town some 80 Five coal mines, four of which are of Lake Waahi, a lake with significant The discharges of mine lodgement water important environmental constraint on Throughout New Zealand the use of water is controlled by a statute called the Water and Soil Conservation Act 1967. All industrial water users are required to hold Water Rights, which are in effect licences to take, use, dam, divert or discharge water. Water Rights are obtained through a legally defined process and any potentially affected party has the per to object to their granting. A special tribunal hears the evidence for and against an application, and issues its decision, which is reviewable in a higher court on Appeal. Rights, if granted, are issued subject to conditions and, in the case of mining discharges, limits would be set on flaw rate, suspended solids concentrations, turbidity, pH and the concentrations of any potential toxicants. This paper presents a case study of an integrated, catchment wide water management plan for Lake Waahi, that was prepared by the author, and others while the author was in the employ of CoalCorp, and its predecessor, State Coal Mines. The author is grateful to CoalCorp for their permission to submit this paper.

Jan 1, 1988

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992