Search Documents

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

By Sergeant G. D, Norman J. R

The importance of reducing the moisture content of fine coal, the nature of the retained water and the means of its removal are discussed. A statistical technique, using a balanced block design, was used to isolate the significant factors determining water content of a coal filter cake, The most significant factor was particle size distribution. A simplex evolutionary operation (evop) was used to determine the optimal quantities of additives required to produce the lowest moisture content for a selected coal size. For this optimum condition (18.6 lb xÇ20 per 100 lb dry coal), additions of 0.045 lb magnesium ion, 0.0026 lb separan A.P. 30, and 0.098 lb aerosol O.T., per 100 lb dry coal were required. The work illustrated the uses of statistical evop technique for the determination of optimal conditions in industrial research projects.

Jan 1, 1969

Mining is a high risk, high capital and potentially high reward undertaking. A large proportion of the risk comes from a lack of definition of the orebody (which also provides some of the potential) and the unpredictable nature of the market. This makes the planning process difficult but encourages the development of a robust yet flexible mining system. The system should be capable of absorbing some deviation from the anticipated concept without a significant impact on profitability. The mine planning process tends to consist of a series of related but discrete stages. For instance, the pit shells are designed, a schedule for the pit shells is created, a plant fleet is chosen to achieve the schedule and a financial analysis is carried out on that scenario. It is likely a few iterations are carried out using various mill throughputs to produce a favoured financial result. The problem is that handing results from stage æBÆ for use in æCÆ doesnÆt encourage a flexible system. æCÆ is likely to be built for exactly æBÆ. Unfortunately, in mining, æAÆ (the orebody) has the highest potential for variability and impacts everything else downstream. æDÆ the market also has high potential for unplanned variability. These variations can spread and æreverberateÆ through the whole mine process. For example an unexpected increase in ore oversize impacts all downstream mine processes to the primary crusher which may in turn create problems back æupstreamÆ by restricting throughput rate. Also an unexpected drop in demand or price could require modifications to the planned production rates. This paper looks at how mining process simulation can be used to support the development of strategies to counteract unforseen circumstances or alter production to match fluctuations in demand and price.

Jan 1, 2003

By F Mwijage

"The benefits of measuring blast movement to reduce ore loss and dilution have been recognised by many people for many years and various methods have been used with limited success. Geita Gold Mine is running the pilot study on the blast movement monitoring (BMM) system which is a revolutionary method developed and patented by the University of Queensland and Blast Movement Technology (BMT). The system consists of directional transmitters placed within the shot prior to blasting, which are then located after the blast with a special detector and then the data is processed with purpose-designed software.As part of continuous improvement on grade control, Geita Gold Mine is running a research project in all operating pits with the objective of: quantifying the three-dimensional blast muck pile movement and finally utilise the movement data to define post-blast ore polygons and incorporate the movement dynamics during block modelling,quantify the potential savings for ore loss and dilution,improve mine geologists knowledge of blast dynamics, andstimulate greater co-operation between drill and blast engineers and geologists to achieve optimum blast designs.To any operation with selective mining, it is critical to the economics of an operation to control ore loss and dilution; getting it wrong will result in significant lost revenue. Implementation of ongoing pilot study on electronic balls as determinant on blast movement dynamics on ore would be of longer term solution and big investment pay back.CITATION:Mwijage, F, 2012. Pilot study on blast movement monitoring at Geita gold mine, in Proceedings Narrow Vein Mining 2012 , pp 49-58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992

Cannington is a Broken Hill type deposit discovered by BHP Minerals, now BHP Billiton, in 1990. The deposit is located south east of Cloncurry, Queensland, Australia. The deposit occurs in the Eastern succession of the Mount Isa Inlier within the Soldiers Cap Group. The mineralisation is interpreted to be confined to two limbs of a synform wrapped around a core amphibolite. The silver, lead and zinc mineralisation is zoned within silicic and mafic units. There is a strong association between silver and lead. The combination of mafic and silicic zoning, differing relative grades of silver, lead, zinc and iron, the relative position of the mineralisation on the synform limbs and differing metallurgical performances have resulted in the identification of ten different ore types, four of which are currently extracted. Ordinary Kriging (OK) is used as the resource estimation methodology for the silver, lead and zinc mineralisation. This modelling approach has performed quite well for resource reporting and long term mine planning. However the limitations of this modelling technique to adequately provide information on a local stope scale has lead to the geological staff to consider alternatives to this approach. Limitations of the current modelling method apply to both the geometry of the orebodies and the grade variability. Since early-2000 the Cannington geologists have been experimenting with modelling both the distribution of the mineralisation types using Probability Field conditional simulation (PF) and the distribution of grade using Sequential Gaussian Simulation (SGS). This approach to local modelling of mineralisation type and metal grades using conditional simulation (CS) has undergone a full evaluation by comparing grades estimated for stopes using both the (OK) resource model and conditional simulation (CS) models. The mine planning staff have used the CS derived models, and have found improvements in grade predictions over the currently utilised Ordinary Kriging û derived resource model.

Jan 1, 2003

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By Tyson G. R

A novel system has been developed using computer imaging techniques to make on-line measurements of material on a moving conveyor. Meas- urements of the mass or volume of conveyor materials are important in large open pit mining operations such as those operated by the State Elec- tricity Commission of Victoria (SECV). Such on-line measurements can be used for monitoring and controlling the production and transport of coal or overburden, and to assist in maintaining production levels. This paper describes a conveyor burden volume measurement system which is currently under development at the Research and Development Department of the SECV and although targeted initially for use in the Commission's open cut mines, the system is suitable for use on any open conveyor system. A basic developmental system has been built to demon- strate the viability of the technique used and further work on the system is planned. The measurement technique and the major components which have been developed as part of the system are described, some comparisons are drawn with other existing measurement systems and potential errors and future development are discussed.

Jan 1, 1989

By B Roach, P M. Ashley, B Hooper

Mineral occurrences of the Hillgrove Au-Sb-W district are hosted in late Palaeozoic polydeformed, hornfelsed metasediments and Permo-Carboniferous granitoids of the NewEngland Orogen. In excess of 204 individual occurrences have been identified to date with the mineralisation developed as strike extensive (>20 km of known veining) and potentially depth extensive steeply dipping fissures. These are contained within an elongate area measuring some 9 km by 6 km in surface dimensions. Recorded gold production of 720 000 ounces along with current resources in the order of 340 000 ounces highlight the significance of this district. Historical antimony production is estimated at in excess of 50 000 metric tonnes. Significant tungsten of over 2000 t in the form of scheelite has also been produced from the field. Mineralisation is developed in veins, vein breccias, sheeted veins, network stockworks and as alteration sulfide haloes to the main structures. The vast majority of fissures are subvertical and vary in widths of up to 20 m in places. Paragenetic studies have previously indicated that the earliest mineralising event was a scheelite-bearing phase of quartz veining. Subsequent phases of arsenopyrite-pyrite-quartz-carbonate veining were accompanied by gold and minor base metal sulfides. Alteration is typically sericite-ankerite-quartz. Overprinting stibnite-quartz veining with gold-electrum, aurostibite and arsenopyrite form an important subsequent phase. Veining can be inferred from historical records to extend for vertical depths of over 1 km.

Jan 1, 2004

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

Comminution of solids is surely one of the oldest technologies which even in this day and age of DNAs, chips and space exploration continues to challenge our scientific acumen and engineering ingenuity. In essence, this challenge is two-fold. One, as much as three to four per cent of all electric power generated world-wide is consumed in crushing and grinding primarily because the utilisation of energy is woefully poor. Studies have shown that the efficiency of mechanical size reduction processes is of the order of 1.5 to 12 per cent only (Schoenert 1986). Two, with the grinding technologies available to us, we have, at best, inadequate and, at worst, almost negligible control over the shape of the comminuted particles, size dispersion of the ground mass, and the sharpness of mineral liberation. Low energy efficiency and lack of control in the sense mentioned above have far-reaching implications for resource conservation, performance of down stream unit operations, and damage to the environment. Our problem is in fact central to the mineral-energy resources triangle shown in Figure 1 which depicts the close interrelationships among mineral resources which are becoming poorer in content and more complex in mineralogy each day, energy resources which are depleting rapidly without any viable alternate on the horizon, and environmental concerns which can no longer be ignored. It is evident that any improvement in the efficiency of the comminution process impacts directly on the control of environmental damage, conservation of energy and the economics of the operation. These concerns have special relevance for the processing of non-ferrous ores.

Jan 1, 1992

By Sneddon J

This Is not a highly technical paper, but rather an attempt to give a general outline of coal mining for the benefit of those present who may have little or no experience in the industry, and is intended to give some general knowledge which may help to a better understanding of the problems of the industry. A knowledge of the disposition of workable material is necessary to give a comparison with other mining practices. Coal Is usually found in comparatively fiat seams of varying thickness, whereas other minerals are generally found in highly inclined lodes of variable width. However, even in comparatively flat seams unaffected by faulting, grades can, and do, vary greatly over short distances.This variation causes many local problems in working the small area affected. Even very steep seams, and some are much steeper than 1 in 1, vary considerably not only in grade, but also in direction of grade and level course. This is probably caused by folding during alteration of the shape and form of the basins after deposition.These swellies are common to most coal seams and vary only in extent. This type of variation in grade and direction of grade, while common to most ore bodies, is a matter of great importance in coal mining when it is considered that roadways are driven in the seam itself and have to be graded and made suitable for haulage purposes.The area of ground involved in an individual coal mining operation is often very large; many times larger than most metal mining propositions, and often comprises many thousands of acres.When it is considered that the specific gravity of coal may be only one-fifth of that of some ores mined, and the coal seam may be five or six feet in thickness, the vastness of the area necessary for continuous mining operations over many years will be realised.To achieve comparable outputs, with about five times the bulk of material to handle, much more ground and working places must...

Jan 1, 1947

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By Sulanto J, Talonen T

In the mid 1960's Outokumpu considered building a lead Flash Smelter on the basis of Flash Smelting technology developed first in the late 1940s for smelting copper concentrates. Pilot scale tests were carried out and the process was found technically sound. The project was however not economically viable under Finnish conditions and it was cancelled. In 1981 pilot plant tests were restarted after many enquiries from the primary lead producers. All the know-how and development made in copper and nickel smelters was applied to the Lead Flash Smelting process and the tests were successful. Outokumpu has so far tested several types of lead concentrate with lead contents ranging from 28 to 75 per cent. The concentrate is oxidized and smelted to metallic lead and slag directly in the Flash Smelting Furnace using high oxygen enrichment of tonnage oxygen. Fossile fuel is used in the Flash Smelting Furnace in cases when the feed material does not contain enough latent heat to smelt the furnace products even though pure oxygen is used for oxidation. Thus the process results in a low consumption of extraneous energy. Use of oxygen results in a small gas flow but it is rich in sulphur dioxide. The gas treatment facilities and sulphur recovery plant will be small in size and low in investment cost. The process is flexible and can produce stable quality of products from different types of raw materials. Quality of lead bullion especially the sulphur content can be regulated over wide a range, from 0.1 per cent upwards according to the needs of the refinery.

Jan 1, 1984

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

Aluminium, the third most abundant element in the earth's crust, has been regarded by some people as the metal of the 20th century. A metal symbolising another great leap forward in man's technological development.From the stone age man advanced to the bronze age, the iron age and now the age of aluminium.The 19th Century discovery of elec-tricity was quickly followed by the discovery of the Hall-Heroult process of smelting aluminium. It is this same basic process we use today.

Jan 1, 1985

The object of this paper is to show in some detail the mining challenges that have been presented and overcome during the successful development of the main exhaust ventilation drive that will service the Ballarat East mine during its 20+ year lifespan. Topics to be discussed in this paper include the ground support regimes employed, the ground conditions encountered during construction, how the heading was recovered after falls of ground and the effectiveness of geotechnical probe drilling at Ballarat.

Jan 1, 2006

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

In mid-1998 Atlas Copco Rock Drills AB introduced the first member of a new family of drill rigs. This new family, Rocket Boomer L1C/L2C/L3C, is based on modern computer technology and also on what is characterised as information technology. The design of the drill rigs are modularised both in hardware as in the software. This means that the functionality of the drill rigs is upgradable step by step. Added upon the basic drill rig functions are the new options as ABC Regular (known also as Contour Control), ABC Total, drillplan generator and communication products. The main objectives of these functions are to facilitate real quality drilling.

Jan 1, 2003