Search Documents

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In 1972, with the West Lyell Open Pit winding down, mining operations transferred underground. All development tunnelling until the end of the decade was carried out by a fleet of ten pneumatic Jumbos.A decision was made in 1980 to purchase an electric-hydraulic Jumbo and a second was purchased in 1982. Their introduction changed the face of development at Mount Lyell. Significant new demands were placed on main-tenance sections, particularly on electrical reticulation.Subsequently, two further electric-hydraulic Jumbos were purchased from Agnew Mining in 1984, and successfully overhauled and commissioned. As well, two electric-nydraulic production drilling rigs have been purchased. Only one of the original pneumatic Jumbos remains in service.

Jan 1, 1985

There is a difference in design aspects between steel linings and rubber linings for grinding mills. The basic design rules for rub- ber are described as well as the liner designs for different applications.

Jan 1, 1978

The characteristics and causes of the spoil pile failures at the Goonyella Mine are described, and research results from investigations of spoil pile instability are discussed. Some effects on spoil stability of the development of deep strip mining projects are considered and recommendations are made for relevant research.

Jan 1, 1981

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

By Bassett N

The Eneabba deposit, located 280 km north of Perth, Western Australia, and 30 km inland (Fig. 1) is one of the most recently developed deposits of mineral sands in the world. The area has been in production since 1974, while the Associated Minerals Consolidated Limited (AMA) operation commenced production in 1976. Total ore reserves of close to 400 million tonnes contain about 40 million tonnes of heavy minerals (proved and probable).

Jan 1, 1979

INDEX OF CONTENTSComposition of the Brown CoalsIntroductionComposition as minedComposition from drilling explorations:Latrobe Valley Area, East Gippsland, Welshpool-Alberton West Area, Altona-Bacchus Marsh Area, Lal Lal Area, Dean's Marsh Area. The Coal Constituents:Vitrain, fusain, detrital coal, resin, Sulphur, types, distribution, Ash, composition, sulphur, phosphorus, chlorine,,titanium, vanadium, distribution in seam, fusibility, source, mineral ash, chemical ash Bitumen, tar. Factors causing Variation in Composition:Pressure of overburden, moisture content, carbon, hydrogen, nitrogen, oxygen, calorific power, density, compression by warping, abnormal moisture, initial differences in vegetation, conditions of sedimentation, weathering before re-burial.Summary and AcknowledgmentsList of References

Jan 1, 1945

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE CERTIFICATE TO ROBERT COLVILLE BRADSHAW, O.B.E.Today it is my privilege and pleasure to introduce to you, Robert Colville Bradshaw. O.B.E., the third New Zealander to be honoured with Honorary Membership of The Institute. Sir William Hudson and Mr. C. H. Benney were the others.Mr. Bradshaw has been an Affiliate Member of The Institute since the formation of the New Zealand Branch in 1966. Like his friend Matt Benney. Bob Bradshaw is an accountant by training. Last June he retired as senior partner of the firm of chartered accountants, now known as Wilkinson Wilberfoss, with which he served from January 1929.Mr. Bradshaw grew up in New Zealand attending the Terrace School in Wellington, the New Plymouth Boys' High School where he was a boarder, and completing a Bachelor of Commerce at the university now known as the Victoria University of Wellington. He is an elected Fellow of the New Zealand Society of Accountants and an Associate of the United Kingdom Institute of Cost and Works Accountants.

Jan 1, 1977

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007

By Mann T

The use of dolomite as a refractory began in England about 1870 when the basic Bessemer process for the removal of phosphorus from steel was developed by Thomas and Gilchrist.Knowledge of dolomite as a refractory in this country goes back to the early part of this century, at the time when the Hoskins Brothers took over the Lithgow Iron and Steel Works from W. Sandford. The practice then was toimport burned dolomite in casks from England. It is reported that much of the material was powdered when received, but was still serviceable. The earliest. used sources of local stone were in the Bathurst and Mudgee areas of New South Wales, and these dolomites were first used raw. Later, dolomite was burned in cupolas at Havilah near Mudgee, coke being obtained from the South Coast of New South Wales. This plant supplied burned dolomite to the Lithgow steel plant, later to the Australil1n Iron and Steel plant at Port Kembla, and also to the electric steel furnaces at Newcastle, Sydney and Melbourne until the plant was closed down in 1946.The Broken Hill Proprietary Company first obtained its dolomite from George's Plains near Bathurst (this was, really a magnesium limestone) and later from Mount Knowles, a deposit near Mudgee, which was eventually taken over by the CO:plpany in 1918. In 1936 Australian.Iron and Steel acquired from the Southern Portland Cement Company a deposit at Mount Fairy in the Federal...

Jan 1, 1951

By R Brake

The Enterprise Mine Project (EMP) is being developed by Mount IsaMines Limited as the future source of copper ore at the Mt Isa miningand processing complex. Environmental engineering is one of the majortechnical challenges facing the project because of the depth of theorebodies, high virgin rock temperatures and hot ambient surfacetemperatures in summer. This paper discusses the engineering principles adopted by EMP to manage the risks associated with working in these adverse thermal conditions.

Jan 1, 1998

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

I feel a little like the Parson delivering his Sunday Sermon, chastizing his parishioners for not coming to Church. Those who need to hear me are absent.Nevertheless, I hope that if you agree with what I am about to say you will go forth and spread the word.We often hear of the impact mining has on the community. I prefer tonight to deal with the impact some community attitudes have on mining, and I want to point out that the results of these attitudes rebound to the detriment of our society. I want to deal particularly with regulation, taxation, and proflts.In a civilization whose standard of living is essentially dependent on an adequate and reliable supply of cheap metals and fuels, it should be evident to Blind Freddie that mining must be encouraged.I must express concern at the constraints inflicted on the mining industry by our community. We tend to blame Government for our difficulties, but we must recognize that Government acts merely as agent for the community. It is fair to say that in a free society, if Government actions do not reflect the demands of the electorate, then it doesn't stay the Government. It is important though for Government, in framing its policies, to ensure that it is not unduly influenced by the loud voices of minority groups.The people of our nation have every right to demand that our industry meet certain criteria to be allowed to operate. We all wish to live in a healthy and congenial environment, and to have our individual comforts protected. It is essential, however, that the community realizes that its demands on the mining industry are affecting Australia's prosperity.Each new regulation and each new tax or impost has its effect on investment, employment, and national revenue. Restraints result in an increase in costs which in turn raises the minimum value of a mineral deposit which is economically mineable. It results in minerals, which could be mined under more favourable circumstances, remaining in the ground, perhaps lost for ever.

Jan 1, 1978

By Lovitt M

Ora Banda Gold Mine is located in the Eastern Goldfields of Western Australia. Mining is carried out underground by sublevel open sloping resulting in large open stopes. A Mass Blast of approximately 250 000 tonnes was carried out in July 1994 to recover a rib pillar between two stopes, and the crown pillar between the underground mine and the abandoned open pit above. Strategic development within 50 m of the blast consisted of two ventilation shafts and the main decline. This development required careful design and prediction of the blast results. This paper describes the design of the blast, the prediction of the likely effects, the measures taken to reduce the risk to important development, and the results of the blast.

Jan 1, 1995

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911