Search Documents

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The discovery of nickel sulphide deposits at Kambalda in 1966 heralded the development of ò an industry with a capital value of over $1.5 billion producing about 10% of the western world's nickel. ò an unprecedented exploration boom in which over $200 mil- lion was expended in 10 years in the search for nickel deposits. ò a major new class of nickel deposits stimulating exploration for similar deposits overseas. and rapidly propelled a struggling small mining and exploration company to become one of Australia's corporate giants, provid- ing a much-needed stimulus to economic activity in a region suffering from a severe downturn in its principal industry, gold mining. Production of nickel in Western Australia commenced at Kam- balda in 1967 and grew rapidly to a rate of over 30,000 t of con- tained nickel per annum in 1970, 40,000 t in 1973 and 50,000 t in 1975. Early production was aided by a shortage of nickel on the world market due to disruption of supply from the major Canadian producers, resulting in high free market prices for the metal. Since these early years, the industry has experienced a number of cycles of indifferent health due principally to market developments overseas, although the level of production of nickel in Western Australia remained fairly consistent. The two most serious of these, in 1977-8 and 1985-6, forced the closure of a number of mines. Current nickel prices are allowing remaining producers to enjoy a measure of relative prosperity, although there is little general speculation that this will be long-lived. Nickel deposits discovered in the exploration boom were almost exclusively related to ultramafic rocks. Volcanic peridotite (komatiite)-associated deposits, exemplified by the Kambalda ore- bodies, were the targets of initial exploration which was concen- trated on ultramafic sequences near lower stratigraphic contacts with underlying mafic rocks. Subsequently, discoveries made in coarse-grained dunites in interpreted intrusive settings broadened the search parameters.

Jan 1, 1988

By S Garnes, W Austerberry, S Fraser

Despite significant investment in safety in the mining industry (mostly focused on processes and systems), many companies are unable to sustain and further improve their performance resulting in continued workplace incidents. The problem persists despite the best efforts of companies and allocation of resources to achieve Zero Harm. A DSS survey in 2019 found that two out of five companies that cannot manage risks and face disaster, leave the market within five years. All safety/risk management systems have the common steps of risk identification, prioritisation, design of controls consistent with risk tolerance, and verification of implementation/operability of controls. This is then complimented with improvement to one or more of the above elements through learnings obtained from incident investigations. In principle, the above process should work to reduce risks to, and keeping them at, a risk level consistent with risk tolerance in the organisation.

May 5, 2022

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

By K Nilsson, G Cheong

Troy Resources NL acquired a 70 per cent interest in the Mina Sertpo gold project in Goißs State, Brazil, in 2001 following a successful bid for the highly competitive international tender of a tenement package put out by Western Mining Corporation (WMC). The Sertpo deposit is located on cleared grazing land 380 km west of Brasilia and is 30 per cent owned by Amazonia Mineracao Ltda, a private Brazilian company. It is a small high grade open-pittable orebody with a measured and indicated resource of 108 000 tonnes at a grade of 49.7 g/t for 172 500 ounces using a 2.0 g/t cut-off. Troy undertook the project management and development of the project while Amazonia managed the exploration activities and provided other services as required. The project development involved drilling metallurgical test holes, scouring the world to locate an available and suitable second-hand plant, and arranging shipping to andreconstruction in Brazil.

Jan 1, 2004

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

By White PJ, Worrad C

The Hunter Valley Coal Preparation Plant and associated materials handling facilities commenced operation in mid 1982. The new plant and coal handling system were designed to integrate with existing mining and preparation plant operations, but also to be flexible to future mining and marketing developments. The system includes: raw coal stockpiles, a 900 tph dense medium/water washing cyclone preparation plant, clean coal stockpiles, a 7.8 km overland conveyor, large finished product stockpiles and a high capacity train loading plant.The plant's development is described with reference to the original planning objectives. Features aimed at providing operational flexibility and performance are emphasised, including the use of; automated stackers and reclaimers, modular plant, distributed PLC control, a single flight overland conveyor, a network of automatic samplers and blending options to assist quality control.Details are also provided of an innovative technique for control of reclaimer rail track forces, stacker and reclaimer anti-collision systems and the use of DC injection braking.

Jan 1, 1985

By A N. Terblanche, D S. Smit

The paper discusses the improvements achieved after an external sparger flotation column, 1.42 m diameter by 9.5 m high, was installed as a re-recleaner unit at the Northam Platinum LtdÆs UG 2 plant in South Africa. The paper also evaluates the pilot plant data prior to the industrial size column installation as well as the accuracy of scale up from pilot to full-scale operation. Since the installation of the PrepQuip flotation column, the final concentrate upgrade ratio improved from 83 to 105, the 3PGM+Auå recovery improved from 79.7 per cent to 81 per cent and the Cr2O3 content in the final concentrate decreased from five per cent to 2.8 per cent. The upgrade ratio can be improved to 125 with an overall 3PGM+Au recovery of 80 per cent. Conventional mechanically agitated flotation cells achieved only 74 per cent recovery at an upgrade ratio of 125.

Jan 1, 2005

By H Han, X Wang, T Li, D Duan

"In this paper, the reduction and separation behaviour of iron and slag in carbon composite iron ore pellets has been investigated experimentally using an electric resistance furnace simulating a rotary hearth furnace process. The factors that affect the formation of iron nuggets, such as temperature, holding time, molecular ratio of C/O and basicity, are discussed. Results show that the reduction of iron ore, carburisation of reduced iron and the composition and quantity of slag are very important for producing iron nuggets. Through optimisation of process parameters, iron nuggets can be formed below 1300¦C when holding time is 20 minutes, C/O is 0.7 and basicity less than 0.5. This study provides a theoretical and technical basis for iron nugget production.CITATION:Duan, D, Han, H, Wang, X and Li, T, 2013. Iron nugget production technology in rotary hearth furnace process at lower temperature, in Proceedings Iron Ore 2013, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985

Facies associations in the Okiduse Volcanics, woodlark island, suggest that two major volcanic centres erupted synchronously during the Middle Miocene. These centres are referred to as the Watou Mountain Eruptive Centre and the Uvarakoi Caldera. The Watou Mountain Eruptive Centre, centred on Boganuse Mountain in the Okiduse Range, was a typical, moderate-sized composite volcano (or stratovolcano). The seq-uence is readily divisible into lava (Boganuse lava unit), breccia (Nikuben breccia unit) and epiclastic (Talpas sandstone unit) dominant facies, typical of composite volcanoes. These facies girdle Boganuse Mountain and they are interpreted to represent vent, cone forming and ring plain associat-ions, respectively. These facies indicate a reconstructed volcano of approximately 1,700m height with a basal diameter of 7km. The presence of limited exposures of intrusive associated with the vent facies (Kuike'beimmicrodiorite) suggests that the volcano is only partially dissected. The Uvarakoi Caldera is a felsic volcanic system contrasting with the mafic Watou Mountain centre.

Jan 1, 1994

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

Two examples of risk assessment and risk management in action are discussed. The first is in a management context in relation to Kingsgate Consolidated LtdÆs Chatree operation in Thailand. Kingsgate has conducted an over-riding risk management program to assess and manage risk across its complete business from the Sydney and Bangkok offices through to the Chatree Mine and the companyÆs exploration group. This example addresses how Kingsgate has applied risk management, particularly to the process operation, and the benefits that have been gained. The second is in an operational context in relation to Minara Resources LtdÆs Murrin Murrin operation in Western Australia. The subject is the methodology and outcomes of a risk assessment across the Murrin Murrin operation specifically to identify and assess risks with potential impacts from $1 M to $7 M. This section of the paper then shows how the outcomes of the risk assessment were integrated into MinaraÆs strategic plan to debottleneck the plant and increase nickel production.

Jan 1, 2004

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

Mount Isa Mines Limited has been mining copper ore for 50 years. In recent years, this production has been entirely by open stoping methods with cemented backfill, mostly in the large 1100 orebody.This has been the major ore source for 20 years, with smaller amounts coming from the 400, 500, 650 and 1900 orebodies. At present, the 1100 orebody is the only source, and this situation will continue until the deep 3000 and 3500 orebodies begin producing in late 1992/93. Production rates have increased to almost 6 Mt/yr, and are planned to rise to 7 Mt/yr by 1995/96. In the future, there will be a move towards variations of the open stoping system as production moves to more lensy zones of the southern 1100 orebody and to the deeper 3000 and 3500 orebodies. This paper describes current operations in the 1100 Orebody, with some indications of future directions.

Jan 1, 1993

By S Leary

Diamond drilling since early 2006 has identified an epithermal gold-silver (Au-Ag) deposit beneath 140 m to >400 m of cover. The Fruta del Norte discovery had an inferred resource estimate of 58.9 Mt grading 7.2 g/t Au in October 2007. The mineralisation is hosted by Mid-Late Jurassic andesite and andesite porphyry in a regional fault zone beneath mainly post-mineral but in part syn-mineral Late Jurassic cover. The intermediate sulfidation-style deposit formed before and in part during deposition of epiclastic cover in the fault related pull apart basin. In addition to its size and obvious economic importance, the widespread occurrences of visible gold and exquisitely preserved epithermal textures will make Fruta del Norte an important learning tool for explorationists seeking epithermal mineralisation in theAndes and elsewhere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Lee G, Stitt P

The term "industrial minerals" covers a vary wide field. However in Australia this field tends to be characterised by the follow- ing: (1) Relatively low unit values. (2) Product specifications can be exacting compared to the metalliferous field. (3) Product specifications often have to be tailored to the needs of the end user. (4) Beneficiation plants tend to involve low capital outlays relative to the metalliferous field. However they often have to produce products'to a range of specifications. (5) Technology often influences what can be considered as reserves. (6) Because of low unit values industrial minerals tend to be relatively cost sensitive. This is particularly the case in regard to transport. (7) Location of deposits near to major urban areas (markets) dictates a greater pressure on ecological aspects. (8) In Australia there has been a tendency to vertical integration largely due to the restricted market available. Reserves assessment is shown to be critically dependent upon the above Factors.

Jan 1, 1979