Search Documents

By Ramsay WRH

The Mount Stavely Volcanic Complex compri- ses one of a number of northerly trending fault bounded greenstone occurrences in Western Vict- oria, of probable Cambrian or older age. The greenstone belt is coincident with several linear positive aeromagnetic anomalies, which outline the surface and subsurface extensions of these greenstones. Mapping at Mount Stavely has identified serpentinite, variolitic basalt, two-pyroxene and pyroxene-hornblende andesite, dacite, rhyodacite and their pyroclastic equiv- alents. Chemically and mineralogically the volcanics constitute a calc-alkaline assemblage. The mineral potential of the region has been enhanced following a discovery by Pennzoil of Australia Limited near Ararat, of sulphide min- eralisation containing approximately 1 million tonnes at 2.7 percent copper. The volcanic environment of the Mount Stavely Volcanic Complex is discussed in terms of similar environments found in Canada.

Jan 1, 1982

Fluid bed sulphation roasting of bismuth concentrates began at Warrego in 1980 in con- junction with the recommissioning of the Tennant Creek Smelter. This process, develop- ed by Peko Mines, is used to separate copper and bismuth by converting copper minerals to a water or weak acid soluble form and then leaching. Pilot scale testwork conducted at the Australian Mineral Development Laboratories (AMDEL) and by Dorr Oliver Pty Ltd in the USA indicated that close control of bed teaper- atures and exhaust gas composition was required to ensure high levels of soluble copper. After overcoming some initial problems, the plant now achieves typically 89 percent copper extraction. Plant capacity is 2.7 tonnes/h by design but in practice this is limited by feed analysis, air requirements, cyclone operation and calcine particle size Consideration.

Jan 1, 1984

Boring of a 7.5Km long tunnel under the city of Stockholm commenced in January, 1987. The 3.5m diameter tunnel will pass under the buildings and as no ground settlement is allowed, the regulation for water leakage into the tunnel is very strict. Probe drilling will be carried out continuously ahead of the boring and when water is encountered the rock has to be grouted before passing with the TBM. The tunnelling system enables probe drilling to be carried out during boring with the TBM. This has earlier been a capacity reducing factor as the whole operation has been stopped during probe drilling. The project is using a new generation TBM especially developed for hard rock formations which require higher thrust per cutter to get a high penetration rate.

Jan 1, 1987

Pan Australian Mining lid installed a milling and gold leaching plant designed to process 2 million tonnes per annum of breccia sulphide ore. This plant was commissioned in January 1989. Since commissioning, increased ore reserves have been established and the plant has been expanded by the addition of one ball mill and several tanks to increase the design capacity to 3 million tonnes per annum. This additional plant was commissioned in May 1990, bringing the total number of mills up to three, each 4.5 m diameter x 7 m long. The paper details how milling rates have been increased at the expense of grind size to increase the capacity of the original plant from 2 million to 3.1 million tonne per year rate before the additional ball mill was Commissioned.

Jan 1, 1991

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Larsson, K Niiranen

The Palaeoproterozoic Leveäniemi iron oxide apatite (IOA) deposit of the so-called Kiruna type is currently mined by Luossavaara-Kiirunavaara AB (publ.), commonly known as LKAB. The mineralogy of iron oxides, ie magnetite, hematite, maghemite, and goethite is more complicated compared to the neighbouring and more famous IOA deposits of Kiirunavaara and Malmberget. Furthermore, the mineral chemistry of the iron oxides in the Leveäniemi deposit is also slightly different. Especially, the information about the deportment of titanium and vanadium in iron oxides and distribution in the deposit is essential since they can have an impact in the steelmaking process. For this study 50 samples were selected from exploration drill cores and investigated by optical microscopy, FE-SEM-EDS and EPMA at LKAB and the Geological Survey of Finland. Investigations revealed that magnetite is the predominant iron oxide mineral with secondary hematite being the second most abundant mineral. Primary hematite, maghemite, and goethite seem to be less abundant. It should be noted, however, that this investigation focused on magnetite which currently is the only mineral with economic value. Vanadium occurs as a substitution element in the crystal lattice of iron oxide minerals in the Leveäniemi deposit and not as discrete stochiometric vanadium minerals. In the investigated samples vanadium concentration in magnetite ranges from 0.12 to 0.32 wt per cent V2O3 with higher concentration in the southern part of the deposit. Contrary, titanium does not substitute for iron in the crystal lattice of magnetite or secondary hematite (less than 0.018 wt per cent TiO2). It either occurs as tiny inclusions of titanium oxide minerals or as exsolution lamellae of ilmenite in magnetite. The spatial distribution for titanium in the deposit, however, remains unknown. Furthermore, results of this study indicate that alteration of primary magnetite to secondary hematite has had no significant effect on the trace element chemistry of these minerals in the Leveäniemi deposit.

Nov 8, 2021

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In considering the organization of research, it is necessary to know just what research is, what objects are in mind when setting out to conduct research, and what are the functional units which are required to enable a coordinated effort in research to proceed.The dictionary defines research in the following terms: Laborious and patient search, as for truth, diligent inquiry or examination in seeking facts or principles; inquiry, scrutiny; to search or examine with continued care; to seek diligently; to search again; to examine anew.This is, of course, simply a formal definition, but the reference to "labour", "patience" and "diligence" should be noted.The following quotation from an answer to the question "What is Research?", published recently in a technical journal, puts some life into the formal definition:- Essentially, it (Research) is nothing but a state of mind a friendly, welcoming attitude toward change. Going out to look for a change instead of waiting for it to come. Research, for practical men, is an effort to do things better... The research state of mind can apply to anything: personal affairs or any kind of business, big or little. It is the problem-solving mind as contrasted with the let-well-enough-alone mind . . . It is the "to-morrow" mind instead of the "yesterday" mind. Note the statements that: Essentially, it (Research) is nothing but a state of mind, and the research state of mind can apply to anything.

Jan 1, 1950

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B J. Wilde

Evaluating the resources and reserves in a mineral deposit requires many interdependent subjective decisions. The decision of stationarity is arguably the most important. This decision includes: the choice of domains that subset the entire deposit, modelling the boundaries of each domain, and understanding and considering the nature of the contacts between domains. Reasonable choices are made in consideration of the geological context, the available data, the goals of the study and the available resources for the study. This paper reviews aspects of the decision of stationarity in modern resource assessment with a focus on quantifying uncertainty and using numerical/statistical tools to help the geomodeller. The use of volume/distance functions to quantify uncertainty in domain limits is particularly important and is presented in detail. The use of contact plots provides help with the continuity of grades across domain boundaries. Realisations are not assembled as a branching combinatorial of all possibilities, but as a set of realisations that provide a measure of uncertainty. This paper amounts to a definition of stationarity for modern resource assessment.

Sep 26, 2011

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

By J S. Petersen

The occurrence of coarse gold particles leading to grade complexity and sampling challenges is a common feature of many gold deposits. Poorly designed sampling protocols applied to these deposit types can lead to an excessively high fundamental sampling error. Together with other errors, the fundamental sampling error contributes to the nugget effect. Proper sample collection, preparation and assay protocols are required to minimise this error, and hence reduce the total nugget effect. Reduction of the nugget effect is a key requirement for subsequent geostatistical resource estimates to be effective. A case study from the Nalunaq gold mine in Greenland is presented, which is characterised by notable quantities of coarse gold (>30 per cent +100 ¦m gold) hosted in quartz veins. Diamond drilling provides a good measure of gross geological continuity at practical grid spacings, but is not considered to represent the mineralisation effectively. On-reef development with face and bulk sampling, together with detailed geological studies were undertaken during the resource delineation phase. This contribution describes the nature of the Nalunaq deposit, its gold particle size characteristics, how sampling and assay protocols were developed (including QA/QC issues), application of GyÆs sampling theory and its calibration, and how the data was subsequently applied to grade estimation.

Jan 1, 2005

To obtain the best economic results in treating the comparatively high-grade ore of the Kalgurli Mine a good roast is essential, and the effort of this paper will be to briefly describe the plant and the conditions prevailing in roasting, which, on an output of about 360 tons daily, subsequently enable an average extraction of slightly over 94% of the gold to be maintained.The percentage of sulphur in the ore varies between 2'5 and 3'5, the lower figure existing when treating oxidized ore. The average gold value is 13 dwt; this occurs chiefly as sylvanite, containing .a lower percentage of silver than is usually present in that mineral. One ore body in the mine contains hessite (Ag2Te) in considerable quantity, associated with gold telluride, and when ore from this stope is being treated the silver contents rise to as high as 20 dwt, but the usual amount is about 9 dwt. per ton, of which only a small proportion is extracted. Other metallic minerals, in addition to pyrite, occurring more or less commonly, are arsenopyrite, magnetite, chalcopyrite, and the tellurides calaverite (AuTez)and coloradoite HgzTe3). A small proportion only of the value occurs as free gold.

Jan 1, 1911

Broken Hill has a long history of mining and it is without doubt a world-class deposit. It has seen production since 1885, notwithstanding the strikes that made the city infamous in days gone by and has given rise to three of the nation's leading mining companies; BHP, North and CRA. Prior to the formation of Pasminco in 1988, the mining and exploration activities were undertaken by separate companies who were business competitors and tended to operate in relative isolation. There were a few notable exceptions such as the Central Geological Survey of 1936 - 38 (Gustafson, 1939; Gustafson et al, 1950) and the Mine Managers' Association. The latter sponsored many university based research projects. At a local level there was good communication and cross fertilisation within this remote outback centre through personal contacts and professional bodies such as The AusIMM. Pasminco was formed by the merging of the lead-zinc interests of CRA Ltd and North Broken Hill Ltd. In Broken Hill this meant the joining together of North Mine and ZC Mines, the two largest mines then operating on the Line of Lode, to form Pasminco Mining Broken Hill Operations. The exception was the central part of the orebody, the original BHP, South Mine and

Jan 1, 1997

The appearance of the Cornish miner in South Australia was, in the simplest terms, the result of resource development economics. In Cornwall in the middle of the 19th century tin and copper mining was declining, while in the new colony of South Australia copper mining was booming. Experienced hard rock miners in Cornwall there- fore escaped unemployment at home by accepting an assisted passage to South Australia. There, in a colony where they were needed, they made their skills available and received good wages. There are many testimonies which support this simple thesis. Take for example the following extracts from contemporary newspapers in Corn- wall: Persons of small capital will find this an excellent opportunity for emigrating to the young and thriving colony ... The miner will find a rich and unbroken field for his operations. The Colony abounds with minerals... (West Briton, 19 July 1844) Miners make a great deal of money here (South Australia). All of them earn ú2 to ú3 per week and in many cases when they have a portion of the mine on tribute one person has cleared ú100 in a couple of months or so. (Cornwall Royal Gazette, 21 July 1848)

Jan 1, 1987

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

Optimising a mining or a quarrying operation about the overall cost is quite a challenge as there never is a situation where we have exactly the same conditions regarding rock properties, explosives' performance, mining equipment or evironmental restrictions. The amount of endless influencing parameters and variables make the evaluation process difficult. The enormous progress we have seen during the recent two decades in computing has however significantly increased our ability to evaluate and process the information gathered, and refine our existing prediction models. Refined models demand an increasing volume of good quality information to show reliable conformity with reality. There is a great need for co-operative work in the mining and quarrying society if we shall be able to screen all available data, systematically find the key-parameters influencing the results and to build robust scientific models. No organisations today have all the skilled people needed or can afford to hire the necessary specialists in all the overlapping branches. This paper highlights some on-going work where the Dyno Explosives Group is adding some new pieces to the giant jigsaw puzzle representing the ultimate model of the mining and quarrying operations we all of this society would like to see completed.

Jan 1, 1995

The applicability of Bieniawski and Hoek-Brown empirical strength criteria has been assessed for different groups of coal and various types of intact rocks by using a vast number of published triaxial test data from various places. Analysis of individual data sets revealed that the traditional forms of the criteria do not have a perfect agreement with the data. A strong negative correlation has been observed between B in Bieniawski's criterion and m in Hoek and Brown's criterion with uniaxial compressive strength of materials. Both criteria have been modified and empirical relationships have been introduced for coal as follows:m = 62.903 - 34.213 (log pc) 0.9772B = 10.152 - 4.709 (log pc )0.8889Similar relationships have been developed for different rock types as well.A comparison between the applicability of each of the above approaches with the conventional criteria reveals a very significant advantage for new approaches and a supremacy for the Bieniawski criterion in all cases particularly in the case of coal.The modified Bieniawski criterion fits coal as well as different types of rocks with excellent accuracy.The modified Hoek-Brown criterion gives a good result for rocks but does not fit coal data quite well. In other words, Hoek-Brown criterion is not an suitable one for coal.

Jan 1, 1998

By Lyman G. J

The volumetric distribution of valuable mineral, or phase, within a set of particles is called the liberation distribution. To optimise a mineral processing plant it is necessary to know the liberation distribution in most of the streams, especially those adjacent to separation devices. Possibly the most common method of analysing ore particles is to section sets of similarly-sized particles. However, the observed sections can appear liberated even if the particle is composite. This means that the 'apparent' liberation distribution can be very different to the 'actual' liberation distribution. This discrepancy is called stereological error. One must then somehow estimate the actual liberation distribution using the apparent liberation distribution. This problem is called the liberation distribution problem and its solution is the subject of this paper. The solution is based on a sorting algorithm which uses geometric probability equations. These equations are based on the assumption that sectioning is isotropic and uniform. Apart from these assumptions the equations are completely independent of particle shape or texture. The algorithm is verified by numerical simulation and experimental methods. For the numerical simulations the correspondence between the actual and estimated liberation distributions is excellent. For the experimental methods, the agreement is not as good and appears to be due to experimental errors.

Jan 1, 1995