Search Documents

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering<sub>®</sub> is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The low grade Mount Charlotte orebody was first mined with minimum capital expenditure by mechanised cut and fill stoping. The lower block was prepared simultaneously for open stoping by shaft sinking and installing another crusher and services. Similar development for the third block was discouraged by economic factors and reduced tonnage. Decline develop- ment required less capital and opened up ore reserves commensurate with advance, providing flexibility to stop operations without commit- ment: A 1 in 7 decline measuring 4.25m x 5.5m to accommodate standard Euclid 25 tonne dump trucks was developed south of the orebody. A fleet of four trucks average 12 loads each per shift over a haul distance of 700m.

Jan 1, 1973

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By V Kumar, A S. Venkatesh, R K. Upadhya

The enormous iron ore deposits of eastern India are part of the volcano-sedimentary basins containing iron and to some extent manganese deposits that belong to the Iron Ore Group (IOG) of Archaean Singhbhum Craton, occurring as western and eastern limbs of a broad synclinorium. The eastern iron basin contains typically huge amounts of blue dust and powdery ores. There is a remarkable difference between the western flank ores and the eastern flank ores and the present study is part of the eastern flank ores from Noamundi. Demand for sintered fines as blast furnace feed coupled with the higher export price for lumpy ores that produce enormous amounts of fines during processing has created a situation whereby both primary and secondary fines, such as classifier fines, are being increasingly used as sintered feed for blast furnace. Systematic mineralogical and geochemical characterisation indicates that in many cases the ROM and classifier fines have to be processed to increase their Fe content and at the same time reduce their Al, Si and P contents. The fines which are already at micron sizes are amenable for beneficiation using the Mozley mineral separator and sink float test. It was observed that beneficiation was better and significantly greater by the sink float method than the Mozley mineral separator. Mineralogical and chemical studies of the fines reveal that around 80 per cent of alumina bearing minerals (gibbsite, clay and silicates) are present in the liberated form. Microscopic studies confirmed that the iron minerals are well liberated by controlled grinding to -300 mesh sizes with the beneficiation of iron ore fines and low-grade ores carried out using the Mozley mineral separator and sink float test. Beneficiation using the Mozley mineral separator increased the grade of concentrate with increasing flow rate of water as well as increase in amplitude of oscillation of the tray, but not very significantly with the increase in slope of the tray. In this method, though, iron concentration improved from 47 to 63 per cent with a recovery of around 67 per cent. It is not suitable for industry scale operation as only a small quantity of ores can be handled at a time. Beneficiation using the sink float test produced a better result with the Fe content increasing from 47 - 49 per cent to 66 - 68 per cent with a recovery of approximately 58 per cent. Initial feed Al2O3, SiO2 and Fe contents of 9.85 per cent, 15.3 per cent and 49.8 per cent respectively were beneficiated to 2.13 per cent Al2O3, 1.5 per cent SiO2 and 67.5 per cent Fe in the concentrate, with a recovery of 54.1 per cent. In contrast, using the Mozley table resulted in beneficiable contents 66.3 per cent Fe, 3.01 per cent alumina and 2.05 per cent silica. The combined alumina and silica content for the Mozley Table was >5 per cent, which exceeds the industry requirement of

Jan 1, 2005

By S Farrokhpay, M Zanin

Although it is well understood that in flotation collection zone and froth zone are deeply interconnected, and reagents (and in particular collectors and frothers) cannot be selected without considering their synergistic effect, this concept is rarely applied in plant practice. The feed mineralogy also has an important role in how particles and reagents interact in flotation, which is sometimes overlooked by operators. In this work, a combination of batch flotation tests and froth stability measurements was used to optimise the collector and frother scheme for the flotation of a copper ore. The methodology was applied to an Australian copper plant which was experiencing high variability in froth stability in the roughers when the feed ore mineralogy was changing. It was hypothesised that chalcopyrite in the feed in combination with isobutyl-xanthate had a destabilising effect on the froth phase under the reagents scheme used. Froth stability was restored if a shorter chain length, less hydrophobic, xanthate was employed. It is apparent that the hydrophobicity of adsorbed films at the solid/liquid/air interfaces has a critical role in enhancing or reducing froth stability. Unstable froth causes a reduction in copper recovery in spite of a high collection zone flotation rate. The case study suggests that collection zone and froth zone can rarely be optimised independently of each other. With the laboratory procedure adopted, a more suitable reagents scheme was determined to respond to changes in the feed mineralogy, avoiding fluctuations in plant performance due to unexpected froth instability.CITATION:Farrokhpay, S and Zanin, M, 2012. Synergic effect of collector and frother on froth stability and flotation recovery - An industrial case, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 145-150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By M Behrens

The Melbourne Main Sewer Replacement (MMSR) is a major urban infrastructure project involving approximately 2.3 km of tunnelling and construction works. The works extend from Docklands Precinct, on the southwest edge of the city, southwards to connect with the Hobsons Bay Main Sewer in Port Melbourne. The tunnel boring machine (TBM) tunnelled section of the works terminates at the Yarra River where the delta geology and alignment requirements precluded the use of underground tunnelling methods. The 132 m long river crossing works involve a cut-and-cover excavation within a staged fl ooded cofferdam construction to construct an immersed tube tunnel as an extension of the TBM works.This paper reports on the development of the staged construction method and highlights the geotechnical and structural design aspects involved in building a new sewer in the Yarra River to close the gap between the new TBM driven and pipe-jacked tunnels.

Mar 8, 2011

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W D. Erskine, M J. Saynor

Ranger Uranium Mine, surrounded by Kakadu National Park is located in the Alligator Rivers Region (ARR) in the wet-dry monsoonal tropics, 250 km east of Darwin, Northern Territory. A trial landform (TLF), measuring approximately 200 m by 400 m (8 ha) was constructed during late 2008 and early 2009 by Energy Resources of Australia (ERA), adjacent to the northwestern wall of the tailings storage facility at the Ranger Mine. A collaborative research program involving the Environmental Research Institute of the Supervising Scientist (eriss) and ERA, has been underway to measure long-term (five to ten year) rainfall, run-off, sediment and solute losses, seepage and vegetation establishment on the TLF (Saynor et al, 2012; Lowry et al, 2014). This paper reports on bed load losses from four erosion plots built on the TLF. These were achieved by physically isolating approximately 30 × 30 m areas from the surrounding landform on three sides with sidewalls along with an open polyvinyl chloride (PVC) pipe on the downslope side. Each plot was instrumented with a range of sensors. Two plots, 1 and 2 were constructed on waste rock material, while plots 3 and 4 were constructed on waste rock mixed with approximately 30 per cent lateritic material. Plots 1 and 4 had tube stock planted in early 2009, and plots 2 and 3 were initially planted by direct seeding in July 2009 and were infill planted with tube stock in January 2011.CITATION:Saynor, M J and Erskine, W D, 2016. Bed load losses from experimental plots on a rehabilitated uranium mine in northern Australia, in Proceedings Life-of-Mine 2016 Conference , pp 168–171 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By K C. Corin, N Ndamase, M Tadie

Mining operations in arid regions are compelled to reduce their consumption of fresh water. Closed water circuits are an attractive solution and, in addition to reducing freshwater consumption, have the added benefit of reducing reagent consumption as well as the environmental impact by eliminating effluent discharge. Accumulating ionic species have been shown to hinder collector adsorption which reduces the recovery of valuable minerals. Numerous studies have investigated the effect of degrading water quality on collector adsorption however there is very limited understanding as to how this takes place from an electrochemical perspective. This study therefore aims to investigate how the presence of accumulating ionic species at varying concentrations affects the electrochemical adsorption of sodium ethyl xanthate onto galena. The synthetic plant water used in this study comprised of single salt solutions to isolate the effects of the ionic species of interest. The ionic strengths were varied between 0.0242 M, 0.0727 M, 0.1212 M and 0.2426 M which correspond to University of Cape Town (UCT) Centre for Minerals Research (CMR) synthetic plant waters of 1, 3, 5 and 10SPW, respectively. Mineral rest potentials indicated how changing water quality affected xanthate-mineral interactions. Microflotation observed the impact of changing water quality on mineral floatability.

Aug 24, 2022

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

By N Barnett, M Dello-lacovo, J Oh, S Saydam, T Pelech

In-Situ Resource Utilisation and Off-Earth mining require the application of horizontal drilling. The stability of such openings is challenging when excavating in the lunar regolith. Excavations on the Moon will encounter unconventional operational conditions such as different material properties, low gravity, and a moonquake. Micro-tunnelling or drilling to support lunar exploration and development of infrastructure on the Moon requires stability analysis to ensure its desired performance. The discrete element method (DEM) modelling technique has been utilised to investigate the optimum opening sizes on the lunar soil. From the literature, the mechanical properties of the lunar regolith have been reviewed and used for numerical model development. The model has been calibrated by simulating numerical triaxial tests with the Mohr–Coulomb failure criterion. Then, detailed parametric studies have been performed to investigate the influence of confinement, opening dimensions and moonquakes on the stability of openings. The findings have led to the development of a simple stability chart of the relationship between unsupported opening sizes and lunar regolith properties at different depths.

Nov 29, 2022

By S M. Gover

Estimating the probability of failure for embankments is not intuitive. It requires not only an appreciation of the strength of the embankment, but an understanding of the variability and uncertainty in the strength parameters as well. These additional aspects are, in themselves, relatively new to most practicing engineers, and therefore require some discussion.This paper discusses the concepts of probability and uncertainty, and presents a reliability-based numerical experiment, together with a literary study and collation of some of the author’s historical slope stability analyses, to investigate whether a direct relationship between safety factors and probabilities of failure exists for certain levels of uncertainty in strength parameters. In doing so, a useful tool is presented whereby knowing the safety factor of a simple slope or embankment with a consistent level of uncertainty, one can infer an approximate probability of failure.CITATION:Gover, S M, 2018. Linking safety factor to probability of failure, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 384–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018