Search Documents

Recovery Process of Carbon Dioxide with Metal Oxides and Metal Hydroxides

Sep 13, 2010

By J Tien, J Huang, N Haque, M O’Brien

Coal preparation is an integral part of producing coal for thermal powerplants and metallurgical processing plants. Coal processing plants use various unit processes to separate gangue and ash content from mineral coal, thus increasing the specific energy content.A flow sheet and a simulation model was established for a typical coal processing plant using Microsoft Excel. This model used the mass balance and split factors for run-of-mine (ROM) coal, tailings and water usage from a typical, generic coalmine.The common method of coal preparation initially involves several stages of crushing to reduce the size of coal. It is then sent to the processing plant for further washing. The typical method in Australia for coarse coal material processing is the use of dense medium cyclone (DMC) (Kininmonth and Baafi, 2009). Flotation cells are used for processing of fine coal. The fine products are utilised for coking coal only. In our case study, the intended coal product is for thermal powerplants. Therefore, the fine coal processing utilised spirals instead of flotation, which is typical for the industry.CITATION:Huang, J, Haque, N, O'Brien, M, O'Brien G and Tien, J, 2016. Development, simulation, economic and environmental evaluation of a coal processing flow sheet, in Proceedings Life-of-Mine 2016 Conference , pp 48–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By P W. Wypych

The iron ore industry faces significant challenges in the control of dust to meet emissions regulations and goals, as well as ensuring sustainable operations. This paper describes some of the different techniques and innovative technologies that are being developed and implemented to improve the suppression of airborne dust, specifically through the use of high energy micromist sprays. The utilisation of computational fluid dynamics (CFD) modelling and simulation is identified and described as a key enabling technology for an improvement in dust suppression solutions both from a level of understanding the source and flow of dust emissions, and for the development of new systems that can be used in the iron ore industry. CFD modelling is shown to be effective for modelling both spray dispersion and cross-wind effects, allowing designers to develop high-efficiency dust suppression systems with a greatly improved level of confidence when compared to traditional techniques. New high energy micromist technology is also outlined as a key element in developing high-efficiency dust suppression systems. Experimental results and industry applications are presented to demonstrate the significant improvements that can be achieved in suppressing or reducing airborne dust emissions.CITATION:Roberts, J M and Wypych, P W, 2017. Research into improving the efficiency of water spraying airborne dust control techniques in the iron ore industry, in Proceedings Iron Ore 2017, pp 359–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

Reason Analysis of Impurity Containing and Technology Discussion of Quality Improvement for Low-Quality Iron Concentrate

Sep 13, 2010

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30 km along strike, although economic resources are confined to a seven kilometre section in the vicinity of the Macraes  township. The shear zone, which typically dips at a low angle (~20¦) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, 'lode schists' and quartz-vein stockworks. Mine geology and grade control activities are designed to ensure accurate definition of ore and waste as well as the accurate prediction of ore grade. Grade control involves an integrated process of blast hole sampling, geological mapping and geostatistical modelling. Geological mapping is carried out post blasting by means of excavating trenches across are zones defined by assay data. Conditional Simulation is used to model raw assay data to define ore-waste contacts and estimate ore block grade, although, geologically defined contacts have precedence. Low angle ore zones impart a wedge shaped geometry to many ore blocks. These ore blocks are bounded by contacts that can be selectively mined to, thereby reducing misallocation of ore and minimising grade dilution.

Jan 1, 2001

Gold was first discovered in the Shotover by Thomas Arthur in 1862. He left his job as a shearer and soon there were up to 3000 miners working over the length of the river. Some parts were extremely rich and a few early miners recovered as much as 300 ounces in a day. From these early days of hand working the operations progressed through to hydraulic elevating once water races and pipes were installed after the Skippers road was completed about 1890. The riverbed was worked in paddocks with .the gravel being sluiced to a central suction which elevated the material over a sluice box. Use of this system continued intermittently through until 1977 when Joe Schieb retired û the last of the hydraulic miners. Many bucket ladder dredges worked on the lower Shotover near Big Beach where the Sew Hoy family recovered a lot of gold. Just after 1900, at least three worked further upstream, one on the beach where Shotover Jet now operates and one further up below the Moonlight. All the sections for this were transported in over the Moonlight Track and the boiler, steam engine and bucket ladder are still sitting at the edge of the river. up near Maori Point a dredge operated from Dredge Slip upstream. Records are poor on these dredges but they all suffered from the frequent floods and large boulders which damaged the bucket line. The last dredging attempt was about 1930 when a suction dredge was constructed on Maori Beach. This failed as seems to be normal for most suction dredging ventures. The river can drop to very low levels in the middle of a dry summer, and in winter when the water is tied up in the mountains as ice and snow. During 1863 when heavy rain melted snow in the high country, the river rose 35 feet overnight and drowned many miners camped on the banks. The ever present risk of flooding dominates the method of working and plant design.

Jan 1, 1987

Optical sensors have emerged during the telecom boom in the late 1900s, due to the availability to low-cost telecom-grade optical components. It's only after the telecom industry's fall in 2004 that optical sensors became sufficiently developed to be a viable technology for real-world applications. Geotechnical applications have long relied on electrical sensors such as thermocouples, strain, and the venerable vibrating wire to measure physical phenomena. Although these are well suited for a large variety of applications, electrical sensors cannot be used for all applications: these are vulnerable to noise, hazardous voltages and corrosion, limiting the environments in which they can be used. In addition, electrical wires can also become an issue when sensors require external excitation or are distant from the measurement system. Finally, changes in physical properties of electrical sensors and systems over time makes regular calibration a necessity - not easy to do when these are permanently mounted on structures. Optical sensing systems are non-conducting and use light to perform various measurements. There are several optical sensor technologies available, each with different strengths and weaknesses. In addition, there are different methods of interrogating optical sensors, each of which also present different strengths and weaknesses. To make matters worse, configuring the interrogation and scaling to physical units can also be challenging to the unprepared engineer. This paper will present a holistic view of optical sensing, presenting the different optical sensor technologies and interrogation techniques. Sample optical sensing systems will be revealed and top considerations for optical sensing will be presented.

Nov 25, 2010

By J E. Askew

The rapid expansion of gold production in Australia over the last five years can be attributed in part to the development of selective mining techniques for open pit gold operations. These techniques allow an increase in head grade with a substantial reduction in mill feed tonnage, as compared with traditional open pit designs. As a result, the capital requirements for mine development and mill construction are substantially reduced, improving the cash flow profile in the early years of operations. To put such a design into effect, the emphasis of mine production must be on producing gold, rather than tonnes of ore. Mine planning at Martha Hill has been based on such a philosophy. After the quantity and grade of the resource had been defined, the exploration programme was increasingly concerned with the local variability of ore zones, and with determining the position of values within broad ore-definition envelopes. The purpose of this work has been to allow the prediction of the tonnages and grades achievable from various levels of the pit when mining selectively using hydraulic excavators. The studies have so far indicated that the Martha Hill deposit can be mined selectively during the early years of production. The additional costs for detailed grade control and a reduced digging efficiency are more than compensated by the exclusion from the mill feed of much valueless material.

Jan 1, 1986

Topography, location of coal bearing land and existing built-up areas severely restrict locations for overburden disposal and dumping sites north of the Latrobe River clear of the coalfields are assumed until internal dumping areas can be established.

Jan 1, 1982

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

Macraes Mining Company Limited operates a 2.1 million tonnes per annum gold processing plant at Macraes Flat, Otago. This uses a conventional CIL route to treat oxide ore, and a flotation, grind, CIL route for sulfide ore. This paper describes the design and operation of this process plant.

Jan 1, 1992

By B K. Hebblewhite, G Sharrock

The strength and deformation properties of a rock mass are important parameters influencing the design of civil and mining excavations or structures. The mechanical behaviour of jointed rock masses are controlled by the characteristics of discontinuities and the strength of intact rock bridges between discontinuities. To date, analytical, empirical and experimental methods have not captured the key mechanisms controlling the mechanical properties of actual rock masses with non-persistent joints. The emergence of the synthetic rock mass (SRM) in 2007 provides a promising approach for this purpose. In this paper a rock mass with non-persistent joints is analysed with the SRM model based on PFC3D. The influence of joint geometrical parameters on the uniaxial compressive strength (UCS), rock mass deformation modulus (Em) and failure mode is studied. Joint parameters include joint orientation, persistency, spacing and step angle. Prismatic numerical samples with dimensions 300 mm × 150 mm × 50 mm were generated and a sensitivity analysis of each joint parameter on UCS and Em was undertaken. The results show that of the parameters tested, joint orientation has the greatest influence on UCS. Minimum UCS occurs when the angle between the major principal stress and joint surface is approximately 60°. The joint step angle was found to have a significant effect on failure mode and a joint step angle of 90° is the most favourable joint orientation for step-path failure. The importance of joint step angle is highlighted in the discovery of a failure mode bifurcation point at joint step angles of 60° and 90° for joint orientations of 75° and 90°, respectively. For these parameters the failure mode transitions from block rotation to a new failure mode where the coalescence of cracks results in the formation of new small regularised blocks.

Sep 26, 2011

The Role of Mineral Processing in the Development of Cement with Low Carbon Emissions

Sep 13, 2010

The gold salting fraud at Busang on the island of Kalimantan, Indonesia was exposed in early 1997 and resulted from the independent drilling, sampling and assaying of PT Freeport Indonesia which reported assays from the South East Zone with negligible concentrations of gold. Since then, a number of legal actions directed at former Bre-X directors, consulting firms and financial or broking institutions are at various stages and are based on numerous allegations surrounding the supposed existence of obvious and numerous warning signs or æred flagsÆ. These include: the absence of references to visible gold in the drill logs; the alluvial nature of the gold grains; the high gravity recoveries; the invalid comparison with Kelian; the absence of outside scrutiny and the lack of external review/audit and surface depletion of gold. The focus on the red flags has been at the expense of the numerous positive indications or ægreen flagsÆ. These include the morphology and chemistry of the gold grains, the gravity testwork, the amalgamation results, the role of external consultants, the results of a review by one of North AmericaÆs leading minerals auditing groups, the behaviour of the gold at surface and the presence of references to visible gold in the drill logs. The flawed nature of the discussion of the technical facts surrounding Busang has prevented a meaningful and informed discussion about what actually happened and has, therefore, prevented the formulation of meaningful remedies for the future.

Jan 1, 2002

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Direct and Indirect Effects of the Reagent Suite on Froth Stability in Laboratory Scale Batch Flotation Tests

Sep 13, 2010