Search Documents

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002

By Kurihara K, Tanimoto C

Construction and mining sites are often subject to unexpected flooding and extensive delays may occur in locating and installing emergency pumps. This particularly applies to sites located in remote areas. A simple and effective pump, called an air-lift pump, can be built from the equipment available at the working site. The basic req- uirements are a compressed air supply, air hose and conventional water pipes. The air-lift pump is comparatively in- efficient but approximately 35 per cent of the available compressed air power at the site can be applied to pumping. Suprisingly high liquid discharge rates may be obtained in suitable applications. The theoretical and practical consider- ations of the air-lift pump are evaluated and a suggested procedure for the emergency design and construction is outlined. INTRODUCTION. Sudden inundations of water into mine and development excavations require the immediate removal of the water if extensive and often irrepairable damage is to be avoided. Pumps installed in shafts or tunnels may become un- servicable due to being totally submerged during the flooding. The emphasis is on rapid

Jan 1, 1976

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

By J Battista, J Grace, I Brunton

The need to better understand and develop strategies to improve instantaneous shovel productivity at the Cadia Hill Open Pit Mine (CHM) instigated the development of the æShot to ShovelÆ project. This project has involved the implementation of a drill and blast (D&B) information management system to capture current and future experience. Equally important has been the manual monitoring of shovel productivity and direct use and analysis of high precision GPS and productivity data logged by ModularÆs Dispatch System. The analysis of this type of data was facilitated with the application of GIS based software (ie MapInfo). This has shown to be a powerful medium to display, interpret and assess this type of spatial information on a blast-by-blast basis. Cadia HillÆs well-defined D&B processes supplemented with the application of the above systems are providing a unique capability to assess and better understand the impact of both muckpile conditions and operator proficiency on instantaneous loading productivity. This is facilitating the definition of appropriate optimisation strategies in both drilling and blasting and operator proficiency training. This paper gives a summary of the work conducted in the æShot to ShovelÆ project, describes the engineering tools being implemented and discusses preliminary findings and their practical implications.

Jan 1, 2004

By S Thomas, S Ricketts, R Hassell

Northern Star Resources (NSR) operates several operations utilising narrow vein stoping operations in the Kundana area. Stope dilution performance is variable across these operations, with unplanned dilution reducing individual stope economic viability, increasing risk to personnel and machinery operating in and around the stope and delaying the overall stoping sequence. Technical investigations were undertaken to objectively understand the variables which had the largest impact on stope performance and then use the findings to help develop mining strategies to reduce dilution. A stope reconciliation process was developed to compile key stope performance information such as stope design parameters, geotechnical and drill and blast factors. These were compared against the measured dilution. Production targets necessitated a high turnover of stopes in the operations, and hence a requirement for an expeditious process and mine design software with automated tools. The output of these results, together with numerical variables from geological, geotechnical and drill and blast data were analysed via multivariate regression. The analysis identified the factors with the greatest influence over stope dilution, and a forecast model was consequently created. Confidence was gained in the model when the subsequent stopes performed in line with prediction. Different drill and blast designs were subsequently trialled and found to reduce dilution. The model was then updated with the new practices, facilitating further regression analysis to identify revised key controlling factors. The subsequent production results however, displayed a poor correlation with the prediction from the revised model. Inconsistencies in drill and blast designs and execution were identified as key factors in the dilution performance. This was an important finding as the correct implementation of the design is critical and this has become a key focus for future stoping. Overall the technique presents an objective process to identify causal factors of stope dilution resulting in improved economic metrics for stope production. The process will be applied to other similar Northern Star operations.

Mar 15, 2021

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

By B N. Morrison

In all metallurgical plants metallurgists require analyses of the various intermediate products, eg flotation feeds, flotation concentrates, tailings, mattes, slags, etc to monitor the efficiency of the plant processes and for plant control purposes. Traditionally these samples have gone to off-site laboratories and there can be some considerable delay before analytical data are received. On-line monitors have to be used for plant control purposes and these are difficult to maintain and can give poor quality data. Recent technological advances in automation in analytical laboratories now allow a far quicker turn-around time for analytical data so they can be of more use to the metallurgist. Automation, which involves the use of robots and fewer people in laboratories, has the added benefit of providing higher quality data as the possibility of human error and bias is minimised. Differences between conventional manual laboratories and automated laboratories are described. Automated analytical laboratories are now becoming the laboratories of choice for mining companies which require large numbers of samples to be analysed on a 24/7 basis on similar sample types using the same sample preparation methods and analytical procedures. Automated laboratories have now been installed in platinum, iron ore, copper and aluminium producing mining companies. A further advantage to metallurgical plants is now the possibility of siting automated analytical laboratories in-plant and designing the plant around the laboratory. Concentrator streams, slags, etc can be sampled by automated samplers, the samples transferred by automation to the in-plant laboratories and all sample preparation and analyses carried out by automated processes. These laboratories require a minimum of staff. Such automated in-plant laboratories have been installed on a platinum mine flotation plant, a platinum mine smelter and steel plants. One is in process of being installed on an iron-ore mine with the sampling being carried out by an automated sampling tower. The procedures followed in planning an automated analytical laboratory for a metallurgical plant are described in detail in the paper. The platinum plant smelter automated system which includes rapid transport of samples by air-tube to the laboratory for the analysis of the samples by XRFS is also described in the paper. It is concluded that automated analytical laboratories can be retro-fitted to most metallurgical plants but they are best suited to greenfield sites.

Jan 1, 2008

Two key elements in the design of a pastefill or high density backfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: Vacuum or pressure filters. These represent the ætraditionalÆ approach to the preparation of pastefill. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producingpaste/high density backfills. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach.This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material. No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mines in Canada.

Jan 1, 1998

For over 50 years R W Miller & Co Pty Ltd operated old coal properties abandoned by former owners as uneconomic, some of which dated back to the last century. The companyÆs ability to survive with what were relatively poor quality coal resources required a small efficient management organisation. In 1970 R W Miller was involved in negotiations with other coal companies through coal sales contracts to develop private coal areas under the provisions of the old Coal Mining Act (1906) and these efforts led to the development of Lemington colliery. At the same time development of the Ironbark colliery holding near Newcastle commenced. In 1971, R W Miller approached the New South Wales Government for a resource replacement area to prospect for coal in the Upper Hunter Valley. Authorisation No 33 was finally granted on 30 September 1975, but the company found the area was inaccessible as most of the surface was owned by the Australian Army. Later R W Miller was granted Authorisation 66 of 2167.5 hectares at Mount Thorley near Singleton on 1 November 1976. The development of this coal mining project coincided with the second OPEC oil crisis in 1978 and a short-term boom for coal resources and the unrealistic expectations generated by the boom. This paper gives a broad outline of the development of the Mount Thorley project between 1976 to 1986 including the feasibility study and the many governmental and industrial delays that resulted in a three-year time overrun in the project development period.

Jan 1, 1998

By K Whelan

The Land Access Branch of the Mines Division of the Northern Territory Department of Mines and Energy is responsible for Aboriginal Liaison and cross-cultural matters that affect the Department. In essence, it exists to provide a basis for communication between the Department, industry. Aboriginal organisations and Traditional Owners. The paper outlines the various ways in which this is accomplished including the preparation of detriment submissions for pending land claim hearings, the use of promotional material to support access to Aboriginal Land for NTGS Mapping Programs and field work, and advice/assistance on exploration and mining issues.

Jan 1, 1994

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By N Petropoulos and M J Thurley, E Righetti, M Wimmer

Fragmentation in sublevel caving (SLC) is vitally important. Both gravity flow and any downstream processes are affected. Reasonably coarse fragmentation may lead to larger draw bodies (isolated extraction zones) and hence potentially higher primary ore recovery and depressed/delayed waste rock inflow from above. Fewer flow disturbances are expected by mitigating oversize. In addition, it requires less boulder handling and reduces wear and possible hang-up problems in orepasses. To assess the present-day functionality of large-scale SLC, a multiyear, comprehensive measurement program was initiated. It covers the main elements for SLC, namely blast function, fragmentation and gravity flow. The present paper focuses on fragmentation measurements. An image acquisition system was used to document the drawpoint and the load-haul-dump (LHD) bucket for each mucking cycle. At the beginning, four buckets (about 70 t total) were sieved to validate the results of both 2D and 3D image analysis techniques. The fundamental and specific problems are discussed herein. At the moment, fragmentation of the SLC rings is evaluated using a quick rating system and a 2D fragment delineation software. The results enable a description of fragmentation and its variation during mucking but also – combined with the gravity flow measurements – conclusions on the fragmentation for different parts of the SLC ring. Possible influences on flow disturbances and ore recovery/dilution are investigated. The recent findings allow a better understanding of breakage and flow and support future process improvements.CITATION:Wimmer, M, Nordqvist, A, Righetti, E, Petropoulos, N and Thurley, M J, 2015. Analysis of rock fragmentation and its effect on gravity flow at the Kiruna sublevel caving mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 775–792 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By L Rachmad

Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) deposit which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. Evaluations were made on former block caving mines at PT Freeport Indonesia (IOZ, GBT Area I and II) in order to design a more appropriate support system. As a permanent support, the thread bar bolt support system is widely used in the DOZ mine. The advantages of this system are ease of operation, quality control and high bond strength. The main problem of this system is the curing time of about 28 days to achieve maximum strength, necessitating the installation of a temporary support for its implementation. In this instance, the system was inefficient in operation and studies were required to find an alternative grouting system. This paper examines the evaluation of thread bar bolt support system and compares the performance of two types of grouting (resin cartridge and cement cartridge) with cement grouting performance. The evaluation is conducted with a pull out test. The advantages and disadvantages for each grouting method, comparison of cost estimation and grouting application in mine scale are presented in this paper.

Jan 1, 2002

Professional engineers of today require a wide array of experience and knowledge. It is true that commonly engineering degrees do teach the technical requirements well, but do fall short in the way of teaching other non-technical issues of professionalism to the student. Today calls for an engineer who does not only have a high standard of the technical knowledge required for their degree, but also has a broad range of experience in areas that are becoming increasingly important in engineering. The importance of social responsibility, liability and interpersonal relations is high. Through the face of the changing world, it has become clear that there is a need for a new type of engineer, who has a broad range of expertise, as well as the typical technical abilities required. This paper will outline these non-technical issues and propose ways of combining these ideas into the mainstream engineering degree.

Jan 1, 2004

By T Takayama, R Muroi, M Matsumura

The steel industry occupies 14 per cent of CO2 emissions in Japan, and the sintering process is one of the major emitters. Since most of CO2 released from the sintering process comes from coke fine combustion, replacement of coke fines with biomass char as bonding agent is a potential countermeasure. In order to explore the effective use of biomass char, we chose char made from Palm Kernel Shell (PKS) as a sample. First, the char’s combustion behaviour was examined with varying the char’s particle size by means of admixing the char in alumina ball packed bed placed in an electric furnace. As a result, the finer the PKS char the faster the burning rate and reaching a higher temperature compared to coke fine. In addition, it is also concluded that the optimum size of PKS char was larger than coke fines. Next, the effect of different heat profiles on sinter structure was examined by sintering tablet made of chemical reagents. In this experiment, the chemical composition is designed based on sinter composition. By this sintering test, even at high temperature, rapid cooling is effective to make fine sinter matrix and fine pores, which has possibility for high sinter reducibility. Based on these two experiments, using PKS char as a sinter fine source has the possibility to improve sinter reducibility.

Nov 8, 2021

Selective continuous surface mining is a rapidly developing system of mining which will have a significant impact on many present and future open cut mines. In many aspects the technology is in its infancy, whilst in other facets concepts drawn from other sectors of engineering are well proven. Full development of the potential and benefits of this technology will only be achieved if the mining companies and manufacturing companies work together to produce machines which the end user really wants.

Jan 1, 1986