Search Documents

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By J Seppelt

The Kanmantoo Copper Project is owned and operated by Hillgrove Resources Limited and is situated in the Adelaide Hills region in South Australia. Mining in the area has taken place off and on over the last 140 years to recover metal from both copper and lead-zinc ores. This paper focuses on the commissioning, ramp up and future outlook for the copper concentrator at the Kanmantoo Copper Project with major focus on issues encountered and operating performance achieved to date.CITATION:Seppelt, J, 2012. Commissioning of the Kanmantoo Copper Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 127-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P Walker, I Crnkovic, D Bennett

The Phu Kham deposit represents a copper-gold porphyry system, with mineralisation present in skarn, stockwork and disseminated styles. Significant folding and alteration events have created a complex heterogeneous mineralogy horizon. Weathering and water table contact have created a leached zone, overlying transition zones with supergene chalcocite- dominant secondary copper mineralisation and clay-rich gangue. Primary ore copper mineralisation is mainly chalcopyrite with minor bornite. The major challenges to the copper-gold flotation process are a wide size distribution of chalcopyrite mineralisation and poor primary grind liberation, a high pyrite content in skarn ore requiring aggressive pyrite depression conditions, clay-rich gangue and non-sulfide copper mineralisation in weathered zones, and a significant association of gold with pyrite.The Phu Kham concentrator has been developed as a conventional semi-autogenous grinding (SAG) and ball milling circuit followed by selective rougher flotation, regrinding and cleaner flotation to produce a copper concentrate containing payable gold and silver values. The concentrator flow sheet design offered a capital efficient compromise between high copper recovery bulk sulfide flotation with large cleaning capacity, and lower recovery copper selective rougher flotation to ensure concentrate specification of 24 per cent copper grade could be achieved. This paper will examine and discuss concentrator flow sheet development, including projects implemented since commissioning to improve copper recovery, and future projects designed to maintain and enhance copper in concentrate production with decreasing copper grade and increasing pyrite content of ore feed, and increasing hardness of primary ore.CITATION:Bennett, D, Crnkovic, I and Walker, P, 2012. Recent process developments at the Phu Kham Copper-Gold Concentrator, Laos, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 257-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Rheological Behaviour of Clay-Rich Gangue Mineral Dispersions During Hydrometallurgical Treatment Alumino-silicate minerals invariable may present an intractable challenge in hydrometallurgical operations employed in low grade nickel, copper and gold ore leaching or high level nuclear waste (HLNW) processing. The interactions and reactivity of alumino-silicate clay gangue minerals such as muscovite/sericite, chlorite, kaolinite and smectite under acidic (eg pH <3) or alkaline (pH >13) conditions can have a striking impact on the particle interactions. These may manifest in undesirable pulp rheology, poor extraction rates and challenges in the subsequent "handleability" and solid-liquid separation processes (eg dewatering). In the present work, a review of investigations involving the interfacial chemistry, interactions and rheological behaviour of aqueous dispersions of mica-group, layered alumino-silicate clay (muscovite / sericite) and chalcocite minerals as a function of pH in the range 2 - 9 and time at 25¦C, is presented. Particle zeta potential, reflecting interfacial chemistry, indicated a strong pH-history and particle volume fraction dependency. Pristine particles' zeta potentials measured from high to low pH indicated mineral-specific isoelectric point (iep) at pH range 2 - 5. Subsequent measurements from low to high pH showed pH-history dependency with iep shift to higher pH values, the extent of which also depended upon particle volume fraction and aging time. Pulp pH-mediated particle interactions revealed by shear yield stress analysis displayed a bifurcation behaviour and good compliance with DLVO theory. The maximum pulp yield values occurred at the iep whilst weak rheology was observed where the magnitude of the particle zeta potential was greatest. The pivotal role played by both pulp chemistry and suspension conditions in regulating the particle interactions and concomitant rheological behaviour is highlighted. The implications of the findings with regards to clay-base pulps' handleability and its control during aqueous processing are discussed.  

Sep 13, 2010

By S Bailey

In-field sampling programs generally take time, equating to money, and unless you have an onsite laboratory, you have the issue of having to wait long periods for your data. Until recently, field portable X-ray fl uorescence (FPXRF) analysers, which can help provide instant indicative results, were not able to detect penalty elements, such as Al and Si, or do so reliably enough to act upon.The purpose then of this field test then was to show that the latest FPXRF devices are capable of producing reliable readings on field samples of variable grain size, in particular for Al and Si, such that the readings still correlate well with the assay for those samples and thus be reliable for an iron ore grade control application.We tested RC chip samples on-site in the Pilbara, Western Australia, with the Niton, analysing for a range of elements including Fe, Mn, Al and Si and then compared the results for those elements against assay data for the same. A strong correlation would tell us that the FPXRF results were reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for the all of the four elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 0.998).The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF.The data showed allowed for two conclusions:1. the FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with assay, is reliable for a fi eld application in drilling and grade control; and2. the greatest limitation to data quality is sample preparation.

Jul 11, 2011

By H Matsuno, N Oyama, T Yamamoto, K Nakajima, Y Iwami, N Saito

Recently, the quality of sinter feed ore used in sintering process has deteriorated. In particular, Fe has decreased and gangue component has increased in the sinter feed ore. Increase of gangue is not only the factor to influence sinter qualities, but also the factor to increase coke ratio in the blast furnace operation as the increase of slag ratio. Therefore, to cope with the deterioration of iron ore qualities, studies on alternative iron ore resources and development of its utilisation technology have been required.In that kind of new iron ore resources, authors focus on high-grade magnetite fine. High-grade magnetite fine decreases sinter productivity by the decrease of permeability of sintering bed. Therefore a new study for using large amount of magnetite fine is required. In the past, there are some studies about the effect of mixing ratio and size of magnetite fine on productivity and quality, but there are few studies about magnetite fine segregation in charging.In this research, the melting behaviour and interfacial reaction calcium-ferrite, which has important role as bonding agent among iron ores, melts into hematite substrate and magnetite substrate was studied. As the results, it was defined that upper segregation of high-grade magnetite fine is suitable for productivity of sintered ore. Based on this knowledge, the control method of high-grade magnetite fine segregation by magnetic force at charging was studied with DEM (discrete element method) and its verification experiments for magnetic segregation control was conducted in the laboratory.CITATION:Iwami, Y, Yamamoto, T, Oyama, N, Matsuno, H, Saito, N and Nakajima, K, 2017. Improvement of sinter productivity by control of magnetite ore segregation in sintering bed, in Proceedings Iron Ore 2017, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Mining One (M1) is often challenged with the task of evaluating deposits considering open cut and/or underground (UG) mining methods. In many near surface deposits a combination of both methods results in the optimum economic means of exploitation. As common as it is to have open pit mines eventually develop into underground mines, theory associated with determining the optimum underground/open pit interface location continues to be subject to refinement. With recent developments in underground software packages, the generation of rudimentary underground mining stopes from basic economic inputs is not only fast, it provides a practical underground mining solution. The determination of the open pit/underground interface is not new to Gemcom's Whittle 4X (Whittle). However, its solution has only ever claimed to be indicative, mainly due the rudimentary nature of how Whittle represents any potential underground mining. The efficient generation of the aforementioned underground mining solution has provided mining engineers with a unique opportunity. Underground mining can now be represented within the Whittle environment to allow the open pit/underground mining scenario to be modelled with increased accuracy. Providing Whittle with the ability to now consider mineable underground stopes combined with the consideration of time value of money (discounting), has delivered a solution with higher credibility than ever before.This paper will elaborate on the potential value gains associated with improved accuracies in the modelling of any potential underground mining in the Whittle environment. Furthermore, it will explain the importance of incorporating time value of money in the optimisation process to provide a consistent solution through to pit selection and final analysis.

Dec 6, 2010

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By V P. Elpatyevskaya, V S. Arzhanova

Main geochemical problems concerning the environment and mining industry interrelation are connected with the transformation of natural water chemistry by mining wastes. The investigation of many mines in Primorye, the southern part of the Russian Far East, showed that their mining waters have high concentrations of heavy metals and aluminium. Water acidity is primarily connected with the amount of acid-forming sulphide minerals in ores and also depends on the neutralising capacity of rocks. Considerable quantity of metals occur in the waters in dissolved form. Metal concentrations in mining waters exceeds the natural levels by two to five orders of magnitude and can't be reduced to the background levels even after multiple dilution. It is necessary to develop and put into practice new technologies so that to reduce the geochemical impact upon the environment.

Jan 1, 1995

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

A Study of Extracting Vanadium from Stone Coal Using Cyclic Oxidation

Sep 13, 2010

By V Salamakha, K Tang, G Si, J Oh, X Wu, Z Yu

The development of machine learning (ML) algorithms has led to promising advances in lithology classification from geophysical logs, which is indispensable in various underground engineering applications. Due to the resolution and availability of logging data, ML models can recognise lithology change in a definitive form at a fine scale (0.01 m). While the results from previous models indicated promising performance in the classification, the robust capability of generalising lithology prediction to unseen data may not be true for those models due to: (1) data bias caused by borehole selections, and (2) logging data mismatches among boreholes. To this end, this paper aims to investigate the generalisability of ML models and seek potential improvements. Four ML models were selected to be trained on single reference boreholes to test the other (as unseen) in the same region, which includes Support Vector Classifier (SVC), Random Forest (RF), eXtreme Gradient Boosting (XGBoost) and Residual Neural Network (ResNet10). The data set involves 11 boreholes from a coalmine in north-western Bowen Basin (Queensland, Australia): density, gamma ray, neutron, and sonic logs are selected as inputs. Additionally, a data adaptation method is applied for better generalisability. The results show that there is an accuracy trade-off between the same borehole and unseen boreholes across the models. It also indicates a 16–43 per cent reduction in model performance when generalising the predictions (in marco-F1 score), while the adapted data sets can contribute to a around 12 per cent improvement. This study provides a fundamental understanding of the model generalisability when using a single borehole, essential for further correlating boreholes for regional lithology classification; the adaptation method can improve the generalised accuracy, and reduces the labour to label lithology, which facilitates the identification of gas storage mechanisms, geological/geophysical modelling, and stratigraphic analysis.

Sep 1, 2024

By B B. Du, Y N. Lu, L X. Wang, S L. Wu

The cohesive zone in the blast furnace is largely affected by the softening and melting behaviour of ferrous burden because of its vital role in the blast furnace process. The Visual High Temperature Methodology (VHTM) has been given to study the softening and melting behaviour of sinter, two kinds of lump ores and acid pellet intuitively. Before softening, both two kinds of lump ore swelled and more serious for lump ore B because of its denser structure than lump ore A. The softening and melting temperature intervals are different from one another and this phenomenon contributed to the gas permeability of ore layer in the cohesive zone since the ‘ore window’ has formed. Besides, the softening and melting behaviour of mixed burdens have been studied, where it has been found that the softening and melting characteristics of mixed burden A (consisting of sinter and lump ore A) is better than mixed burden B (consisting of sinter and lump ore B) and mixed burden C (consisting of sinter and acid pellet) despite the poorest characteristics of lump ore A. The reason is that the high temperature interactivity between lump ore A and sinter is much better than lump ore B and acid pellet. The high temperature interactivity is mainly influenced by the chemical compositions, porosity and contact condition. This paper provides a new research method for the softening and melting behaviour of iron ore and an important technical basis for the optimisation of blast furnace burden.CITATION:Wang, L X, Wu, S L, Lu, Y N and Du, B B, 2017. The softening and melting behaviour of single and mixed iron ore burdens, in Proceedings Iron Ore 2017, pp 605–610 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Bush, F Goddard

The electrification of Australian mine sites will see a boom in the use of batteries of all chemistries. Lead acid batteries, a traditional mainstay of the mining industry, are expected to nearly double by 2030, however their use will be eclipsed by the explosive growth in lithium batteries. By 2030 the lithium battery market is forecast to be nearly four times the size of the lead acid battery market. Unfortunately, this will result in a corresponding avalanche of waste batteries to be disposed of. Barely a day goes by without battery generated fires being reported in the media and they have become an increasing nightmare for waste management companies and waste facilities. The safe recycling of batteries will also become increasingly important for mine sites to achieve their sustainability goals and reduce their environmental footprint. What are the risks posed by waste batteries, what are the regulatory requirements and how can you manage or eliminate these risks? What current practises does your mine site currently have for the safe management and disposal of batteries from your site? How prepared are you for the coming avalanche of waste batteries?

Apr 16, 2024

By T J. McGavin

This paper examines the fire life systems implemented in two existing tunnels and discusses whether the standards used were appropriate. It focuses on the Terrace Tunnel as this upgrade and refurbishment is complete.The New Zealand Transport Agency (NZTA) manages six tunnels on the State Highway network with two of these built in the last seven years. The Terrace Tunnel, opened in 1978, was refurbished with modern fire life safety systems in 2010–2012. An interim upgrade of the Mt Victoria Tunnel, opened in 1931, was also carried out at this time.In present times, few existing tunnels have undergone significant upgrades and refurbishments. The Terrace Tunnel required: new power supplies, control buildings, lighting, wall panels and jet fans, a deluge system, emergency exit lights and way-finding lights, a public address (PA) system, a radio rebroadcast system, lane control sign (LCS) and variable message sign (VMS), an over-height detection system (OHD) and a new tunnel management system.In the absence of suitable guidelines, various standards were used to carry out the refurbishment. The Austroad Guide to Road Tunnels and AS4825 Tunnel Fire Safety, although designed for new tunnels and not specifically intended for existing tunnels, provided a framework. A multi-criteria assessment of risk (MCAT) was carried out to determine the systems to be provided.The Terrace Tunnel has perhaps set a benchmark for refurbishing existing tunnels as few projects of this type have been completed recently. This paper examines the process and the outcomes.CITATION:McGavin, T J, 2014. The refurbishment of the Terrace and Mt Victoria Tunnels, Wellington, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 87–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S M. Stewart

Building and Maintaining Community Relationships   In mining terms, the town of Waihi is distinctive with the Martha mine situated right in the heart of the town. MarthaÆs central location and other mining activity nearby means there is an increased community focus on the happenings at the mine and the effects and impacts of mining. While WaihiÆs proximity to the mine is unique, all mines have a community context that they operate within.   Issues of proximity simply heighten awareness and emphasise the need for building and maintaining good community relationships. In the three years we have been working alongside the Waihi community, we have worked together with concerned and supportive residents, representatives of Newmont Waihi Gold and representatives of Hauraki District Council, to develop a collaborative framework for addressing the economic, social, environmental, cultural and spiritual wellbeing of the people of Waihi. This could not have occurred without the genuine commitment of all participants.   This collaborative focus has resulted in some tangible progress in Waihi which, in part, stems from people taking an interest in the town because the town is taking an interest in itself. As we have worked and learned within the process of building and maintaining a collaborative and sustainable community environment, we have tried to adhere to a philosophy and a set of basic principles. We believe that this approach, combined with a teachable skill set, helped to create the opportunity to develop a truly collaborative community environment which continues to grow. Our paper will describe this philosophy, these principles and the skill set that we have applied.   The application of the process in Waihi has resulted in a series of outcomes unique to Waihi. These outcomes include formation of the Waihi Community Vision committee, the Vision Waihi Trust and the subgroups set up to further the interests of particular groups, for the collective benefit of all the community.   Based on our experience of other situations, and on the way the Waihi process has developed, we believe that the identified principles and skills can be transported and used in other cultures and contexts. While the resultant outcomes may differ, the underlying principles will still apply. Progress will come from creating a sustainable environment within which the community (including residents, industry and regulatory authority) can determine its own internal relationships and the vibrant growing sense it has of itself.

Jan 1, 2006

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995