Search Documents

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

The Pasminco mine at Rosebery in north western Tasmania is a medium sized underground base and precious metals mine. In April 1992 a major wedge failure of approximately 5000 t occurred in the backs of a main access drive to the 18 level H Lens orebody. This collapse prevented access to 190 000 t of ore which had been scheduled for production in July - August 1992. At the time of the collapse, the mine was in a transition period between mining small pillar remnants of several other orebodies and developing to the new deeper J Lens orebody.The development at this orebody was behind schedule and it was necessary to find a cost-effective and timely alternative to a 75 m bypass drive around the fall area.A Lysaght- Fletcher multiplate steel arch was available on-site from a deferred surface road project and it was decided to use this arch to regain access through the fall area. Due to the danger of continued minor falls, the entire 18 m long, 3.95 m high x 4.5 m wide tunnel had to be assembled in the 4.7 m wide x 5 m high accesss drive and pushed into the fall area as a single unit.

Jan 1, 1993

Generation and Attachment of Submicron Size Bubbles to Colloidal Solids

Sep 13, 2010

In classical drill and blast underground mining methods, especially narrow vein operations economic quantities of broken ore can be left behind following normal mucking operations on the stope floors. The ore left behind can have significant economic value and if not collected can be lost forever. This paper reviews techniques for cleaning this material from stopes that have been used in the past and reviews possible modern techniques that can be applied to ensure this valuable material is removed from the stopes.

Aug 1, 2010

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

Based on relative CO2, N2, and 3He contents, geothermal systems of the Taupo Volcanic Zone, TVZ, can be subdivided into two major groups: arc-type systems, associated with andesitic magmatism along the eastern boundary of the TVZ, and rift-type systems over its western parts. The highly increased N2/3He, CO2/3He and CO2/Cl ratios of the former are ascribed to entrainment of large proportions of volatiles of subducted, marine sedimentary origin. The largely rhyolitic, rift-type magmas are assumed to have formed from volatile-depleted, residual melts. Correlations of Cl and CO2 with heat contents suggest that formation of the two types of source magmas involves mixing of two end member components: a low-volatile melt with a heat/Cl ratio of 25 Ml/mol (0.7 MJ/g), and a low Cl vapor with a heat/CO2 ratio of 5 Ml/mol. On the basis of these values, the heat associated with andesitic magmas is found to be carried in close to equal parts by both vapor and melt; for the rhyolitic melts the proportion contributed from the vapor is only about 2%. The heat/He ratios of the rhyolitic source magmas for the rift-type geothermal discharges from the TVZ of 0.12¦0.05 Ml/pmol is within the range of 0.05 to 0.2 Ml/pmol of the upper mantle. The higher heat/3He ratios for the arc-related magmas of 0.4¦0.2 Ml/pmol are likely to be due to the high proportions of heat carried in the form of a separate, low 3He vapor phase derived largely from subducted sediments.

Jan 1, 1995

Economically significant gold-silver mineralization occurs in Miocene andesitic flows and tuffs at Golden Cross, eight kilometres northwest of Waihi, New Zealand. The highest grade mineralization occurs in a steeply dipping elongate zone of strong quartz veining and brecciation underlying, but contiguous with, a gently dipping tabular quartz vein stockwork containing potentially open-pittable lower grade gold-silver mineralisation. The stockwork zone is enveloped by argillic alteration and overlain by unaltered Pliocene andesites and recent tephra. Evaluation of the prospect involved underground and surface geologic mapping, rock and soil geochemistry, IP-resistivity, magnetic and gravity surveys as well as 1844 metres of reverse circulation drilling and over 30 000 metres of core drilling. The paper outlines the exploration history of the area and describes the results of the various exploration techniques used at Golden Cross.

Jan 1, 1986

By Yindong Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, a O2- , and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of a O2- , which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions. * Originally published in the Proceedings of MINPREX 2000, published by The AusIMM.

Jan 1, 2001

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002

By D S. Clarke, K B. Sporli

The Thames Goldfi.eld has been a major gold resource in the west of the Coromandel Peninsula, New Zealand, with the Waiotahi quartz vein system forming a large part of the field. Mineralisation is hosted by hydrothermally altered Miocene andesitic volcanic rocks. Both massive columnar-jointed and fragmental volcanic rocks are present. The vein system is dominated by the steeply dipping NE striking Waiotahi-Cambria vein, and associated splays. Hydrothermal alteration increases in intensity from isolated blocks of propylitic altered andesitic material, into the intensely clay altered equivalent. Low rank propylitic alteration is typified by chlorite, calcite and pyrite, with local illite or epidote. Clay alteration is characterised by illite, quartz, kaolinite and pyrite. While broadly forming halos around veining, intense clay alteration also occurs in strongly jointed portions of the hostrock.   Vein textures and the intense illitic clay alteration at Thames are similar to those in some of the other epithermal gold deposits of the Coromandel Volcanic zone, and in deposits of the Philippines, all related to andesitic terranes. Possible causes for textures and alteration being different in these deposits from the more classic Quartz-Adularia-Illite type epithermal systems may be that cooling/mixing rather than boiling dominates fluid evolution. Kaolinite may be also be a product of either of these different fluid types, or has resulted from overprinting of an illitic assemblage by downward percolation of acidic fluid.

Jan 1, 1991

By G Collecutt, T O’Beirne, D Humphreys, J Greenwood

Much of our knowledge of the behaviour of underground coal dust explosions has been derived from less than full-scale experimental explosions in facilities as small as 0.25 m diameter pipes. Although a substantial body of research has been undertaken in larger galleries approaching the size of full-scale modern mine roadways, there are still questions regarding the scaling of results to full-sized roadways in modern coalmines. Questions also surround the issue of comparing or scaling results between smooth and rough walled galleries, round and rectangular galleries and galleries with differing wall thermal properties due to different materials of construction.This paper will examine the influence of gallery size, cross-section area and wall roughness and thermal properties upon the characteristics of a coal dust explosion. Data from past explosion research will be examined and assessed for its application to the problem along with theoretical considerations for these factors.Recommendations on the design and minimum appropriate size of explosion galleries for assessing the performance of explosion inerting strategies, passive and active explosion barrier performance and determination of appropriate pressure ratings for ventilation structures will be made.CITATION:Humphreys, D, Collecutt, G, Greenwood, J and O’Beirne, T, 2015. The impact of facility construction and scale on the characteristics of experimental coal dust explosions, in Proceedings The Australian Mine Ventilation Conference, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By R Wilson, R Williams, B Freeburn

McLanahan RSS14x50 scrubber screens have individually processed over 50 Mt of Pilbara iron ore. The first stage of separation in these plants with abrasive, high specific gravity, large lumps is an extremely arduous duty with high wear rates. With the Scrubber Screen layout this occurs in the attached trommel section. The initial supply of the replaceable trommel panels were of steel-backed rubber with a service life of approx. six weeks. Site Personnel established a goal of 26 week wear life in conjunction with 100 per cent reliability and while field trials were undertaken using a variety of hardened and cast steels that demonstrated wear life to the nominated requirement some unpredicted failures still occurred. With a long evaluation time and challenges to create repeatable conditions with field testing, a purpose built test unit was designed and constructed to allow controlled evaluation of a number of materials and designs. During 2016 tests were conducted with eight different materials, of varying thickness to simulate impact conditions and a number of aperture profiles to evaluate both impact and abrasion effects. From these results two designs were selected for full scale implementation to confirm the nominated goals. This paper will present details of both testing procedures and results of all materials, as well as conclusions of successful field implementation.CITATION:Wilson, R, Freeburn, B and Williams, R, 2017. Trommel panel development for iron ore applications, in Proceedings Iron Ore 2017, pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Improved roof control in high deformation tailgate environments has been achieved over the last decade through development of stiffer and increased capacity standing support products. æThe CanÆ is one such development, being a steel cylinder containing a weak cementitious fill, designed to essentially fold in upon itself whilst maintaining strength. A laboratory study to better define the relative load contributions of the steel cylinder and fill, the confining interaction between these components and most importantly, the potential impact of varying the steel and/or fill properties is described. This would enable the support engineer to ædial-upÆ the desired strength and stiffness properties and optimise the standing support design with respect to load capacity, stiffness, weight (handling) and cost. Design curves to optimise strength based on steel casing thickness, fill strength (confined and unconfined) and æCanÆ geometry were established. Scaled-down (one-third) samples were used in the test program and found to adequately reflect the loading behaviour of full-scale versions, thereby providing significantly greater scope for further product development at less expense compared with testing full-scale products.

Jan 1, 2005

In February 1995, Falconbridge Limited approved the construction of a nickel mining and milling facility on its Raglan property situated in the Nunavik region of northern Quebec, Canada. The construction period successfully terminated with the commissioning and start-up of the plant and concentrator in early-December 1997. The estimated life of the project is 20 years with an annual mining rate of 800 000 tonnes of ore, producing 21 000 tonnes of nickel per year. This paper discusses the subject of æRemote Mining in the Canadian ArcticÆ as it applies to the Raglan mine process and people. During the feasibility stage of the project, many assumptions were made which influenced the design and operating parameters of the facilities and the equipment. Transportation, communication, remote logistics techniques and standard industry practices required to support a æfly-in/fly-outÆ operation were reviewed and either adopted or rejected for use at Raglan. These assumptions were æmade to fitÆ the uniqueness of our planned operation. It was also acknowledged that many of them would ultimately impact on the people required to staff the operation following construction. Therefore, their suitability and applicability were examined from an economic, operational and human perspective. In a continuing effort to improve the quality of life for Raglan employees, as well as the economics of our mine operations, these assumptions are under constant review and scrutiny. There is no doubt that experiences gained, and willingly shared by other North American arctic mining operations, proved invaluable and are a big reason for RaglanÆs overall success thus far. The mining industry is being challenged technically to develop lower grade orebodies at the lowest possible cost. In addition to environmental constraints, serious social, political and moral questions are being asked and added to this list of challenges. Miners throughout the world must improve their operating standards and public image if we want to attract the best possible employees. Remote mining operations provide a unique opportunity to experiment with various human resource concepts as well as demonstrate the industryÆs commitment to environmental and community concerns.

Jan 1, 1998

This paper identifies the challenges and opportunities for mining companies and communities in investing in human rights compatible, credible, effective and representative company-community relationships.   The paper draws on the work of Professor John Ruggie, Special Representative to the United Nations Secretary General on Business and Human Rights, and his Protect, Respect and Remedy framework for business and human rights, The CDA Collaborative Learning Project, and the experience of Oxfam Australia. This paper begins with the premise that Australian companies commence operations offshore with high expectations and a willingness to work harmoniously with local communities. However, as companies increasingly engage in global operations - particularly in weak governance and conflict zones - the challenge to establish and sustain rights compatible, meaningful, corporate community relationships and grievances mechanisms becomes both more complex and necessary. Establishing trust and honouring commitments made to communities, including legacy issues, is a critical component in good corporate community relations.   The second part of the paper will identify some of the impacts and challenges of mining that need to be addressed in corporate community negotiations and consultation. Respect for indigenous people's rights and their right to give or withhold consent for a project to proceed is increasingly evident, as is the growing global expectations with regard to revenue transparency. As such, key challenges include: grievance mechanisms; free prior and informed consent; transparency and accountability; the gender impact of mining; resettlement, compensation and benefit sharing; and security issues.   Finally, the paper will provide practical guidance to companies on how to establish effective corporate community relationships. It will include examples, such as human rights impact assessments, gender impact assessments, and establishing local level grievance procedures. The paper will include an Oxfam Australia case study of a dialogue mechanism at Tintaya copper mine in Peru.

Jun 1, 2010

By D Pastars, J L. Mauk

Located at the southern end of the Awhitu Peninsula, the Waikato North Head ironsand mine is approximately 50 km southwest of Auckland . The ironsand deposit consists of Quaternary sands, clays and peats, formed by aeolian and marine processes. We sampled on widely- and closely-spaced intervals to test variability within the mining area. X-Ray powder diffraction shows that samples contain feldspars, quartz, pyroxenes, amphiboles, clays and titanomagnetite. Densities range from 1.6 to 2.5 grams/cubic centimetre, with porosities from 30 to 43 percent. The percentage of magnetic minerals values range from 0 to 75 percent, slimes (clay minerals) values of 0 to 26 percent and non-magnetic minerals from 20 to 95 percent. Mineralogical differences in the Mitiwai Formation and Waiuku Blacksand Member cause bimodal populations in the density, magnetic minerals, nonmagnetic minerals and slimes plots. The Mitiwai Formation has higher non-magnetic mineral values and lower density, slimes and magnetic mineral values than the Waiuku Blacksand Member.

Jan 1, 2001

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

By L Reynolds

Oceana Gold (New Zealand) Limited (OceanaGold) has commenced mining operations at the Globe-Progress mine in the Reefton Goldfield, an area that historically produced 2.1 million ounces of gold from underground quartz lode deposits. During the construction phase of the operation, advanced exploration programmes targeting near-mine prospects commenced. The focus of this ongoing exploration is the discovery of near surface, refractory gold deposits that are amenable to open-pit mining methods and treatment through the Globe-Progress process plant.   One such discovery is the Supreme deposit, located along strike approximately 3 kilometres to the south of the Globe-Progress mine. The Supreme area was tested extensively with diamond drilling in 2006, defining a deposit with similar mineralisation styles and grade to the Globe-Progress deposit. The mineralisation comprises a central core of gold-bearing quartz veins, locally containing visible gold, surrounded by a more extensive halo of refractory, disseminated gold associated with an arsenopyrite-pyrite sulphide mineral assemblage. Three subparallel mineralised structures host the mineralisation. These structures are highly oblique to the country rock orientations, extending approximately 250 metres along a northeast-southwest strike and at least 220 metres down-dip, with an average thickness of 12 metres and moderate dip to the southeast. Records of historical workings indicate that mineralisation extends further down-dip and remains open at depth. 5175 ounces of gold were mined historically at the Supreme deposit. OceanaGold have defined an Inferred Resource for the Supreme deposit of 0.84 million tonnes at 1.46 grams per tonne for a total of 40 000 ounces (at a 0.8 grams per tonne cut-off). Higher-grade zones of mineralisation exist within the deposit and further drilling is planned to test the extent, continuity and geological controls of the mineralised structures.

Jan 1, 2007