Search Documents

By J Seccatore, G Sadao, M Cardu, G De Tomi, L Finoti, F Galvão, J Romero Huerta, A Rezende, J Bettencourt

In the mining industry, rock blasting can be considered as the first phase of comminution. The downstream phases of comminution are mechanical, and consist in consecutive stages of crushing and milling for grain size reduction. The total energy of mechanical comminution depends on grain size and on the resistance of the material to grindability. Usually, the first is quantified by the grain size distribution or one of its KPIs (such as the diameters X50 or X80), while the latter by the working index (WI), representing the amount of energy necessary to reduce the size of grains of a determined amount of material to the desired equivalent diameter (usually expressed in kilowatt hours per tonne – kWh/t). It is widely recognised that it is possible to manage the output of a blast in terms of grain size distribution varying specific charge (powder factor – PF) and charge distribution; specific algorithms such as the KUZ-RAM or the SWEBREC have been created to predict such output. It has also been demonstrated how higher PFs weaken the blasted material by creating micro-fractures that reduce its WI. This paper focuses on a related aspect: the influence of charge distribution on the specific comminution energy in crushing and milling. Small-scale blasts have been performed on 14 marble blocks with different PFs and charge distribution. For every PF, charges have been designed to simulate concentrated and distributed geometries. Concentrated charges simulate opencast blasts with large-diameter holes, with large burdens and spacings. Distributed charges simulate bench blasts with small-diameter holes and reduced burden and spacing. Three control blocks have been fragmented by mechanical means for comparison. For every sample the grain size distribution and the WI in ball mill has been determined. Results show the correlations between charge distributions and the specific energy of mechanical comminution in milling. Finally, the opportunity of adjusting charge diameters and distributions in opencast blasts to improve the output of the comminution circuits is discussed.CITATION:Seccatore, J, Romero Huerta, J, Sadao, G, Cardu, M, Galvão, F, Finoti, L, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The influence of charge distribution on the grindability of the blasted material, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 749–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Developments in the technology of explosive production and deliveryallow a greater amount of flexibility in rock fragmentation by blasting. The rock fragmentation efficiency of an explosive is currently given by a rating which is determined by the explosive manufacturers using proprietary formulae and methodology. Hence, comparison of explosives from different manufacturers may be misleading. Modeling of explosive energy, using a thermochemical code such as CHEETAH provides an objective standard by which the likely performance of different explosive formulations can be determined. Such modeling can be used for optimisation of explosive composition to match specific rockfragmentation objectives.

Jan 1, 2001

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

An extensive series of tests was carried out on a ball mill-rake classifier circuit in the New Broken Hill Consolidated Ltd. concentrator. The data were used to develop a mathematical model of the operation of a rake classifier and this model has been used in the simulation of the performance of a ball mill-rake classifier circuit on a digital computer. As a result of this simulation it has been possible to develop a technique for the optimization and control of a circuit which includes these units.

Jan 1, 1967

The GPS and information technology industries are now applying considerable development effort to what is being termed machine control and machine information systems, in particular focusing on the industries the of mining construction and agriculture. GPS based systems are demonstrably finding common acceptance and adding commercial value to many machine applications in industry. This has been the first step in the evolution of the information age that is now reforming mining practices. Adding the technologies of wireless data communication, modem computer databases, and networked PC's mining is on the verge of a new era in overall process management. This paper is a general discussion of what the information age means to miners and a general description of new mining operation technologies available to day from the Caterpillar technology alliance.

Jan 1, 1999

Industries in the Kwinana area have embarked on a journey of improving the eco-efficiency of Western AustraliaÆs primary heavy industry area. The Kwinana Industrial Area has some unique characteristics that provide both opportunities and barriers. The Kwinana Industries Council and the Chamber of Commerce and Industry are working with the industries to identify a range of projects that can deliver improvements for both environmental and economic æbottom linesÆ, and to progress these projects using internal and external resources. The evolution of the process, its relationship to the ethos of operating companies, and the availability of resources to pursue projects, is an interesting study with lessons for others interested in taking the same course.

Jan 1, 2002

The Australian metallurgical processing industry has shown great innovation and progressiveness over the past ten years. During the same period, exploration activity, particularly by Australian companies, has increased substantially in Indonesia. Following feasibility studies, the decision was made to establish a metallurgical laboratory and design facility in Indonesia. An Indonesian partner was selected, and legal and corporate matters were determined. The laboratory was established but proved far more difficult than a similar undertaking in Australia. Australian and Indonesian staff were recruited and training programs, including training of Indonesian staff in Australia, were implemented. Difficulties of operating in Indonesia included: ò language difficulties ò _ local pace of life ò culture ò communications. Rewards of the decision to establish the means to present the technology to Indonesia have included: ò a contribution to Australia's export of technology. ò an opportunity to expand Normet's client base. ò the opportunity to learn aspects of a foreign culture. ò the means to establish a sound long term investment. This export of technology from the Australian mining industry to Indonesia is an example of the initiatives and capabilities shown by the Australian mining service industry.

Jan 1, 1989

By AUIMM AUIMM

Continuous Improvement The Council of the AusIMM should expedite the introduction of a continuous professional education policy along the lines of that to be proposed to you by David Pollard today. The Education and Accreditation Committee must continually review the training needs of the next generations of mining industry professionals. It should continue to demand and encourage the creation of the schools for the training of such people. The AusIMM could even put greater onus upon university researchers to accredit university post graduate degrees.

Jan 1, 1994

Flotation of Composite Synthetic Particles

Sep 13, 2010

By H J. Dalstra

High-grade iron ore may be derived from banded iron formation (BIF) through four fundamentally different processes:1. syngenetic precipitation of chert free BIF,2. residual enrichment by removal of gangue minerals from BIF to form bedded (residual) ironore,3. mechanical erosion of iron oxide and chert from bedded iron ore or BIF and re-deposition andupgrading as detrital iron ore, and4. chemical removal of iron from BIF and precipitation elsewhere as a secondary (channel) irondeposit.Finally, the BIF itself may constitute iron ore if a high-grade concentrate utilised for pellets or sinters can be derived from it through mechanical (industrial) separation of iron oxide by means of crushing/milling and mineral separation.Historically, exploration for high-grade BIF hosted iron ores was focused on the residual (bedded) deposits and driven by supergene concepts. Exploration for detrital and channel type iron ores was mostly secondary to exploration for bedded deposits, but recently, a more focused exploration effort has led to the discovery of enormous moderate to low iron grade deposits in the Pilbara region of Western Australia. Exploration for high-grade iron ores using syngenetic concepts has been limited,but together with exploration using hypogene concepts offers the best hope of fi nding concealed deposits. Exploration for BIF sources suitable for concentrate ores commenced in the ‘old’ iron ore provinces after the high-grade resources were depleted and has only recently gained importance in Australian BIF provinces, mainly as a result of high iron ore prices in the last decade.

Jul 11, 2011

By Adeloju S, McQuade CV, Riley SJ

Metal contamination of sediments can be an issue for minesites discharging water. Water sampling of receiving waters is frequently undertaken. Sampling and analysis of sediment is less common. The variability of receiving environments makes the formulation of a generic sediment sampling strategy virtually impossible. Each situation needs to be carefully assessed before sampling is undertaken. This paper outlines the approach taken for one such survey.The main factors that need to be considered in a survey of surficial sediments are sample representativeness and sample variability. A simple data set from one site within a regional survey is used to illustrate the importance of these factors. The metal content of sediment is shown to vary significantly over small spatial scales.The variability associated with the spatial distribution of samples within a site is shown to be the most significant source of variability in the study. This variability could bias the results of a study if not planned for in the sampling methodology. Taking multiple samples from within each site (sub-site samples) and combining the data gives a more representative indicator of overall conditions than a single sample. The optimum number of sub-site samples to be taken from each sampling site was found to be 15.It is shown that a composite of sub-site samples can give a good indication of the average site metal content, while considerably reducing the sample preparation and analysis effort.

Jan 1, 1998

Laboratory testwork was carried out on an overall orebody composite, of 2.9 per cent Cu and 4.2 per cent Zn, prepared from drill core taken from the Currawong fine-grained, copper-zinc massive sulphide deposit near Benambra in Victoria. While 90 per cent of the copper was readily recovered in a concentrate of 20 per cent Cu, after grinding to 95 per cent passing 38 microns, zinc responded poorly to conventional flowsheet/reagent regimes. Experience elsewhere with the use of reverse cleaning, to separate pyrite from sphalerite, led to a series of tests in which better (but still modest)metallurgical results were obtained. The best result was a zinc recovery of 55 per cent in a concentrate of 50.5 per cent Zn. The major loss of zinc occurred in the reverse cleaning stage where the unit recovery of zinc was similar to pilot plant results achieved at Mount Isa Mines on similar feedstock. Diagnostic mineralogy suggested that an overall zinc recovery of 70 per cent was probably the practical upper limit, at a 50 per cent Zn grade.

Jan 1, 1999

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the "carbon monoxide ratio") it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure· indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

The passage of chloroform vapour in a carrier of oxygen through two nickel sulphide ores heated to 380°C converted the nickel to the water soluble chloride form. In one ore the nickel (2·75 per cent) was presentas violarite ((Ni, Fe)3S4) whereas in the second it was present as pentlandite, ((Fe, Ni)9S8) (4·9 per cent Ni).A similar technique was utilized to convert nickel in nickeliferous laterites (1·6 per cent Ni) into a soluble chloride using town gas instead of oxygen as a carrier.With both techniques greater than 90 per cent extraction was achieved.

Jan 1, 1972

By O Haavisto, N Khajehzadeh, L Koresaar

Online analysis of metal content can be used to optimise the grade and recovery of a flotation circuit. Compared to conventional laboratory analyses, the benefit of an online analyser is the speed of the measurement, therefore disturbances (eg changes in feed grade and decrease in recovery) can be reacted to in real time by an operator or automatic process control system. In some cases traditional X-ray fluorescence analysers can be applied to silica analysis in iron ore when the SiO2 grades are high enough and have a negative correlation with iron; however, generally a laser-induced breakdown spectroscopy (LIBS) analyser is more suitable for low Z elements.The Outotec Courier 8® analyser is a LIBS based analyser able to measure elements starting from lithium (Z = 3), thus being able to measure impurities; eg silica and aluminium directly in iron ore slurries. Besides online elemental analysis, the analyser can be combined with optical measurements for rapid continuous measurement of each sample line. Laboratory testing has also shown potential for mineralogical analysis using the combination of LIBS and reflectance spectroscopy.CITATION:Koresaar, L, Khajehzadeh, N, Haavisto, O and Timperi, J, 2017. Online elemental and mineral measurement of slurries in iron ore beneficiation, in Proceedings Iron Ore 2017, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967

Crandallite and millisite in Christmas Island 'B' and 'C' phosphate ores are rapidly decomposed by sodium hydroxide solutions at about 80QC. As these phosphates generally contain less than 1% silica, an alkaline extraction process can be designed, in which up to 95% of the sodium hydroxide used, may be recycled. The insoluble residue consists of an impure, highly reactive apatite, which in pot trials, has given good responses as a direct application fertiliser; alternatively this residue can be underacidulated to give a granular product with fertiliser potential. The hot leaching solution contains up to 95% of the alumina and approx- imately half of the phosphate from the original ore. Simple crystallising techniques have been developed on a laboratory-scale to use this leaching solution for producing smelter-grade alumina and detergent-quality trisodium phosphate. As the demand for detergents is limited, an investigation was made of the reaction between trisodium phosphate and slaked lime, derived from a high-grade New Zealand limestone occurring near Oamaru. The product is calcium phosphate, containing up to 40% P205, and less than 0.2% each of iron, aluminium and fluorine, and it should be a useful raw material for phosphoric acid manufacture. A preliminary economic evaluation of the whole process looks promising, And warrants further investigations, including pilot-plant work.

Jan 1, 1971

By D Craw

Bulk ore tailings from the Macraes gold mine gold extraction process are stored in a large (ca 0.6 km2, 80 m deep) mixed tailings impoundment whose pH is maintained near 8 by natural rock neutralizing capacity. The mixed tailings will be stored in this impoundment in perpetuity after mining ceases. Confidence in the long term environmental stability of these tailings can be gained from examination of mineralogically and chemically similar geological situations in the immediate vicinity. A sequence, typically about 5 m thick, of sands and gravels derived from the Macraes mineralized zone 12 000 to 28 000 years ago contains rounded detrital sulphide mineral grains which are unoxidized despite close proximity to the surface and occasional incursion of oxygenated waters. Saturating water pH is currently 7-8. Sands with 0.2 to 0.8 wt % organic carbon host sulphate-reducing bacteria (SRB), and localized cementation by authigenic framboidal pyrite has occurred. Comparison of the 28 000 year-old sediments with the modem tailings suggests that similar chemistry will prevail, possibly with deposition of authigenic pyrite in the tailings, in the long term. As long as the present slightly anoxic and circumneutral pH environmental conditions are maintained in the mixed tailings dam, sulphide decomposition and acidification are unlikely. These sediments provide a plausible geological analogue for long-term benign storage of the mixed tailings impoundment.

Jan 1, 2000

By X-F Zhao, J-W Li, L-P Zeng

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of Kiruna-type deposits has been ascribed to either immiscible iron phosphate melt separated from silicic magma or precipitation from magmatic-hydrothermal fluids. The early Cretaceous Ningwu volcanic basin in Eastern China contains tens of Kiruna-type iron deposits. The orebodies are mainly hosted within the top zones of subvolcanic dioritic intrusions and along the contacts between these intrusions and adjacent volcanic rocks/strata.The orebodies are commonly associated with widespread brecciation and wall rock replacement. Magnetite formation was closely associated with extensive hydrothermal alteration that may extend kilometres, with both vertical and horizontal zonation. Field and textural data indicate that magnetite formed slightly later than albitisation but coeval with apatite and actinolite. Elemental analysis of magnetite and apatite from ores shows distinct features to those as igneous accessary minerals in the host dioritic intrusions, suggesting a genetic relationship to magmatic-hydrothermal processes. Magnetites have elevated TiO2 (up to 5 wt per cent) and V2O3 (up to 0.7 wt per cent), which implies that they are derived from incipient high-temperature magmatic fluids. It is concluded that the Kiruna-type deposits in the Ningwu basin most likely formed from high-temperature magmatic-hydrothermal fluids. The emplacement of dioritic intrusions into a subvolcanic setting likely plays a critical role in the development of Kiruna-type deposits.CITATION:Zhao, X-F, Zeng, L-P and Li, J-W, 2015. Kiruna-type iron deposits in the Mesozoic Ningwu volcanic basin, Eastern China – origin and relationship to subvolcanic dioritic intrusions, in Proceedings PACRIM 2015 Congress, pp 657–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Y Tang, G Si

The analysis of rock fragment sizes plays a pivotal role in various stages of geotechnical and mining engineering. Traditional case-based methods often falter in addressing the variability in rock fragment images due to fluctuating geological conditions and imaging environments. To counter this challenge, AI-based models necessitate training on expansive and diverse data sets, encompassing a wide range of conditions and fragment types. However, the creation of such data sets is often hampered by financial and environmental constraints. This paper introduces a novel approach for rock fragment recognition, which leverages the power of AI for data augmentation, automated annotation and prediction. The methodology integrates three key components: Style-Based Generator Architecture for Generative Adversarial Networks (StyleGAN) for data augmentation, the Segment Anything Model (SAM) for automated annotation, and the multiscale version of you only look once (YOLO-MS) real-time instance segmentation model. The proposed method begins by training a new StyleGAN model using the original data set. It then delves into exploring the latent vectors of different rock fragment images to generate specific ‘style representations’. These latent vectors form the foundational elements of each image in a high-dimensional space, encapsulating critical features such as size, shape, texture, and colour variations. The next step involves conducting quality checks on the generated images to ensure their realism and suitability as training data. Subsequently, the augmented image set is annotated using modified SAM module, followed by training the YOLO-MS real-time instance segmentation model. The performance of this model, trained on the augmented data set, is compared with a model trained on the original data set, particularly in terms of generalisation abilities in new scenarios. The results exhibit a significant enhancement in accuracy, robustness, and generalisability of the model trained on the augmented data set, underscoring the potential of StyleGAN as a powerful tool for data augmentation in geotechnical engineering image analysis.

Sep 1, 2024