Search Documents

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

An important consideration in any mining operation is waste disposal management. Tailings management at Macraes gold mine allows for the disposal of tailings into fully engineered embankment dams and overburden material to be incorporated as construction material into those embankment dams. This paper outlines the current tailings management practices.

Jan 1, 1992

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

At Pasminco Mining's South concentrator. which was commissioned in 1952. an expansion. modernisation and efficiency improvement program commenced in 1986 with a coarse ore stockpile and grinding circuit expansion. the replacement of small flotation cells and the upgrading of reagent mixing and metering equipment. The program continued with the installation of a TDC 3000 based process control system (1988) and concentrate thickeners (1990). By mid-1991 a further grinding expansion and the installation of zinc flotation feed regrind ball mills and zinc recleaner column cells will be complete. leaving the use of ceramic disc fillers and development of process control strategies as probably the remaining major avenues for improved process efficiency at present.

Jan 1, 1991

By M Passmore, N Poznik

Olympic Dam is a world-class deposit and is unquestionably one of the most geologically, structurally and texturally complex orebodies in the world. As development advances into the Southern Mine Area (SMA) the geological understanding is rapidly evolving as underground drill rigs are prioritised to provide the additional data necessary to convert Indicated and Inferred Resources into Measured Resources. The SMA represents approximately 70 per cent of Olympic Dam’s total resource and is significantly more complex when compared to the Northern Mine Area with respect to the diverse nature and origin of lithotypes, rock mass characteristics and the extent of major structures controlling primary mineralisation trends.Recent mine development into the central SMA has been impacted by a major structural gouge zone. Sound geological interpretation allowed mine geologists to successfully integrate their local understanding of the distribution of lithotypes with critical geotechnical data, chiefly rock quality designation (RQD), to delineate and better predict this major structural gouge zone. As a direct result, development rates improved whilst also increasing awareness for the importance of sound geological interpretation utilising all available data. In order to maximise predictability across all systems in place through the mining geology value chain, the integration of geological and geotechnical data in a geotechnical RQD block model provides an additional tool to assist in preventative solutions for complex problems to achieve a proactive mining environment.This paper details the methods used to build the RQD block model, the geostatistical estimation parameters, 3D geotechnical domain wireframes, challenges regarding legacy approaches, and collection of geotechnical information and incorporating/linking geotechnical data with geological features, including the use of grade and lithotype domains. Although the geotechnical block model proved difficult and complex to construct, the resultant product has seen successful integration of geological and geotechnical data into mine planning providing higher resolution of critical parameters for local mining areas.CITATION:Clark, J M, Passmore, M and Poznik, N, 2017. Olympic Dam rock quality designation model – an integrated approach, in Proceedings Tenth International Mining Geology Conference 2017, pp 27–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By G Tripp, G Lorusso

The Velvet gold orebody (153 Koz Au) is located near the Kanowna Belle gold deposit in the Boorara Domain of the Kalgoorlie Terrane, a subdivision of the Archaean Eastern Goldfields Superterrane (Swager et al, 1990). Gold mineralisation at Velvet is hosted within an intrusion of intermediate composition that broadly follows a sub vertical hanging wall splay of the Fitzroy Shear Zone.Velvet was discovered in 2003 during an underground exploration drilling program targeting potential strike extensions to the Kanowna Belle deposit. Diamond drill hole KDU1595 returned a downhole intercept of 36 m grading 4.6 ppm Au approximately 500 m west of the deposit and at a vertical depth of 700 m below surface in the immediate hanging wall of the primary Kanowna Belle host structure, the Fitzroy Shear Zone. Subsequent drilling completed following the initial discovery, from both surface and underground collar positions, failed to replicate this result.In 2014, KDU1595 was resurveyed gyroscopically and the mineralised intercept correctly located. Additional drilling was undertaken to follow-up the repositioned discovery hole. Challenges included poor drilling angles through the Fitzroy Shear Zone, excessive deviation during drilling and the unknown geometry of the target. Navigational drilling helped to successfully penetrate the Fitzroy Shear Zone and in April 2015, drill hole KDU3234 returned a significant downhole intercept of 45 m grading 5.6 ppm Au.Additional drilling success resulted in a decision to develop a 600 m drive to serve as a dual-purpose access for further exploration and mining. This was a potential risk considering that the orebody geometry was unknown and all significant drilling results were clustered within a 50 m × 50 m panel. Development commenced in June 2015 and the first ore cut taken in April 2016. Geological mapping and structural interpretation, together with multi-element and spectral analysis of drill samples has enabled several other target areas to be identified for exploration. The Velvet mining area is critical to continued production at Kanowna Belle. Geological understanding must advance as mining progresses to ensure continued resource growth and optimal extraction of reserves.CITATION:Lorusso, G, Rogers, J and Tripp, G, 2017. Velvet underground exhumed – discovery and development of a new mining front at the Kanowna Belle gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 169–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By B Cope, Y Churi

Roxgold was a small exploration company when it discovered the Zone 55 orebody at the Yaramoko project in Burkina Faso in 2010. Since this time, it has actively progressed the project with the completion of a preliminary economic assessment in 2013, a feasibility study in early 2014 and obtained full permitting for construction in January 2015. With no other underground gold mine in Burkina Faso, developing a modern and productive modern gold mine in West Africa was considered a significant challenge as Roxgold moved from explorer to producer.To facilitate this development, Roxgold engaged an international underground mining contractor to partner this development. This has enabled Roxgold to successfully develop the mine over a relatively short time frame with construction commencing in April 2015, first gold being poured in May 2016 and commercial production being achieved in October 2016.This paper discusses key elements of the project development and highlights some of the challenges faced with operating in a remote poorly developed area with a limited mining culture. Furthermore, the authors highlight the key technical and operational aspects that make the Yaramoko project a very successful development project.CITATION:Cope, B and Churi, Y, 2017. The development of the Yaramoko gold project in Burkina Faso, West Africa, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R E. Myers, G N. Phillips

Many of the worldÆs larger iron ore deposits are hosted by rock sequences of Archaean to early Proterozoic age. Most models for the genesis of these deposits are influenced, either directly or indirectly, by the nature of the atmosphere at the time of their formation, and more specifically by the presence or absence of oxygen in the early atmosphere. Since the early-1950s, the geological literature suggests that the Archaean atmosphere was æreducingÆ, and that it may not have contained significant amounts of free oxygen until ca 2 Ga. There are many different definitions of the term æreducingÆ, but the criterion adopted here is whether crustal iron was limited to Fe2+, or whether Fe3+ was also widespread, ie was there scope for redox changes in the state of iron? Significantly, major Australian banded iron formations span this period of inferred atmosphere transition, eg Mt Goldsworthy, Mt Tom Price, Middleback Ranges. Geological evidence for a reducing Archaean atmosphere is both ambiguous and controversial (see review by Phillips, Law and Myers, 2001). Many earlier ideas (eg no Archaean redbeds; all very large iron ore deposits being post-Archaean) have been disproved by dating, whereas other evidence (eg homogeneous detrital gold grains, inferred palaeosols) has not withstood geological scrutiny. The interpretation of some data sets (eg inferred detrital uraninite and pyrite in some Archaean meta-sedimentary rocks) is still controversial. In fact, some lines of evidence now suggest that oxygen was present in the atmosphere well before 2.5 Ga (eg sulfates in the Pilbara craton, carbon distribution in clastic sedimentary rocks). An oxidising Archaean atmosphere has important implications for the development of iron formations. First, the atmosphere is an obvious potential source of oxygen to stabilise ferric iron minerals. Second, reduced fluids in equilibrium with ferrous iron are commonly inferred to transport iron in solution to the depositional site. The redox state of the atmosphere thus provides critical constraints on the solution chemistry of surface waters, effective transport paths for iron and particularly on viable precipitation mechanisms. Iron formations developed from fluids in equilibrium with the atmosphere also have the potential to provide important constraints on the evolution of EarthÆs early atmosphere. If an oxygenated atmosphere is a necessary condition for the development of iron formations, then the Archaean atmosphere must have been oxidising since at least 3.5 Ga. If the redox state of the atmosphere is not a necessary condition, then the time distribution of iron formations cannot be used to provide constraints on atmospheric evolution. Given these uncertainties, models for the genesis of iron ore deposits of Archaean or early Proterozoic age should not rely on a reducing atmosphere in the absence of independent evidence and the alternative of an oxidising atmosphere should also be considered.

Jan 1, 2002

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

By G Sparrow

The Murray Basin is being heralded as the next major mineral sands province in Australia. Already exploration programs have delineated extensive commercial deposits and several companies are progressing with plans to produce zircon, rutile and ilmenite in the Basin. As these deposits are developed consideration will need to be given to several key issues of the Murray Darling Basin; the availability of fresh water and management of salinity in the area being two of them. In this paper ideas being developed in CSIRO that link the processing of mineral sands with the salinity problem in the Basin are presented. The proposal presented here is to process saline water to produce industrial minerals with large volume applications and to produce value-added products from the mineral sands in the Basin using reagents produced from the saline waters. Processes to produce titania pigment and zirconia consume chlorine, caustic soda, soda ash and hydrochloric acid, all derivatives of salt (sodium chloride). There may be a good economic incentive if these processing plants were located in the close vicinity of each other.

Jan 1, 2001

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

Last evening, in Auckland, I heard the Chairman of Heinz US, Dr Tony O'Reilly (who, in addition to Heinz's ownership of our largest food processor, also has substantial personal investments in this country), advocate New Zealand as a 'regional corporate capital'.   Why would someone like Dr O'Reilly hold that view? No doubt, as one of Ireland's great rugby players of the 50s and 60s, he admires at least one thing that we do very well (confirmed again in Dublin over the past weekend). But that's not sufficient to support such a view.   He cited many reasons for preferring New Zealand over, say, Sydney, Australia, calling this 'the most rational in which to locate [an] international headquarters', including û +         we have no capital gains tax; +         a more 'pro-business environment'; +         a 'first class' legal and banking system; and +         a 'simple political system'.   I can find no better 'text for today's address.

Jan 1, 1997

By R Valenta

Most developing projects face a range of technical and non-technical challenges, and examination of development histories can potentially provide insights into improved approaches to project development. The Kestanelik project in the Canakkale region of Western Turkey was acquired by Chesser Resources Ltd in 2008. Turkey is a significant and growing source of gold production, with sector participation by both domestic and international companies. While the broad ranges of challenges faced by developing projects is well known, there are relatively few case studies in which the range of technical, environmental, social and governance challenges are presented in a single contribution. Recent studies of undeveloped complex orebodies have particularly shown the extent to which environment, social and governance (ESG) complexities contribute to project delays and failures. The Kestanelik project faced a full range of technical and ESG complexities, and provides an illustrative example of the associated challenges. CITATION: Valenta, R, 2018. A case study of technical, social and environmental challenges for a gold project development in Western Turkey, in Proceedings Complex Orebodies Conference 2018, pp 73–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By G S. Anderson, N W. McDonald

"The IsaMill™ was originally developed to address liberation issues at Mount Isa Mines (now Glencore) operations, McArthur River and Mount Isa in the early 1990s. Following on from the industrial success at those operations, the IsaMill™ was commercialised. In the year 2000, Kalgoorlie Consolidated Gold Mines (KCGM) became the first external user of the technology with a 1.1 MW M3000 IsaMill™ installed to supplement the roaster capacity at its Gidji Processing Plant. The IsaMill™ was used to ultra-fine grind about 10 t/h of pyrite flotation concentrate to 10–12 µm prior to gold cyanide leaching. Based on the success of the Gidji installation, another was installed at the processing plant at KCGM’s Fimiston operation in 2002 in a similar duty.In 2014, a 3 MW M10 000 IsaMill™ was selected to replace the roasters at Gidji as part of the A$98 M emissions reduction project. The mill was commissioned in April 2015 at the design 30 t/h, allowing the immediate shutdown of the two roasters. Replacement of roasting with ultra-fine grinding completely eliminated air emissions at Gidji while maintaining overall plant production rates.This paper details the history of the IsaMill™ at KCGM from the original M3000 to the latest M10 000. It covers the basis of the process selection, circuit design, operating and maintenance data.Citation:Anderson, G S and McDonald, N W, 2016. IsaMill™ at Kalgoorlie Consolidated Gold Mines - from the M3000 to the M10 000 and Replacement of the Roasters at Gidji Processing Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 29–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The Epithermal and Mesothermal Gold Prospectivity modelling projects carried out by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250,000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, to stimulate mineral exploration and investment in exploration, has been successful with eight new companies acquiring new tenement positions and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were done at a national scale and consequently not all exploration data were compiled into the prospectivity models. Several of the new companies recognised the value of the prospectivity modelling work and committed exploration funds to continue the modelling process. They recognised a need to compile the remaining data and run the models again to allow detailed exploration targeting. Detailed data compilations including digitising historic exploration stream sediment sample, rock chip sample, soil sample and drilling data has been completed. New models have been completed in Otago for mesothermal gold mineralisation and in the Coromandel and Northland for epithermal gold. The new models have been compared with the original regional scale models and used to target prospect scale exploration. This work has allowed exploration models for epithermal and mesothermal mineralisation in New Zealand to be refined. More importantly this work has identified significant areas with potential to host gold mineralisation with little or no systematic geochemical data including soil sampling or drilling. Exploration work programs have been designed to acquire these missing data and exploration funds have now been committed to test the areas highlighted by the prospectivity modelling. In summary, the Epithermal and Mesothermal Gold Prospectivity modelling work has successfully attracted new investment and ideas to the exploration scene in New Zealand. The projects had an estimated cost of NA$250 000 and will in the next two years, just through exploration expenditure, attract more than NZ$10 M in investment. If a mine is discovered the return on investment will be considerably greater.

Jan 1, 2004

The BHP Billiton Cannington Mine uses paste as the principal method of backfill. The paste consists of mine tailings and cement. The pastefill process at Cannington includes a surface plant where the thickened total tailings stream is filtered using two vacuum disc filters operating in parallel. The filter cake is mixed with Portland cement in a spiral mixer to produce a paste at a specified yield stress and cement content. The initial system design only required paste to be delivered under gravity. In July 2001, Cannington Mine expanded to 1.8 million tonnes per annum. In order to achieve this, production commenced on five new levels underground, 350 metres horizontally from the paste plant. Due to the high viscosity of paste, this distance was too far to transport by gravity. Traditionally, paste has been transported only short distances (50 m) using positive displacement pumps, with very limited success. At Cannington, a conveyor was installed which was designed to achieve zero spillage into the environment. This paper discusses the innovative design strategies used to attain zero harm on the environment whilst conveying a material, which is difficult to transport.

Jan 1, 2002

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015