Search Documents

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

THIS paper proposes to give a general description of the pumping and other machinery in use at the Thames Hauraki Pumping Station, situated on the Thames goldfields of the North Island, New Zealand. An idea of the general arrangement of the pumping engines and pumps can be obtained, together with a certain amount of detail, by reference to the illustrations. The history of the pump is rather interesting, and is as follows: -In 1894 the Government decided that a subsidy of £1 for £1up to an amoUllt not exceeding £25,000 be granted towards the erection of suitable machinery to exploit the Thames low levels.With a guarantee of such assistance a company was floated in London, with a capital of £300,000, to develop several properties at Thames. As the old Queen of Beauty Company had produced bullion worth £400,000 prior to closing down on account ofa breakdown to its pumping gear, their shaft was chosen as the site of the principal work. As soon as the company was floated, operations were commenced at the Queen of Beauty shaft, situated at the entrance of the Waio-Karaka Creek, and not more than about half a mile distant from the principal mines on the field.

Jan 1, 1912

The Autogenous Fine Grinding Kelsey Axial Displacement (KAD) Mill The marginal improvements which continue to be made to fine grinding practices have exposed the limits of conventional technologies and highlighted the need for a radically new approach. The patented autogenous Kelsey Axial Displacement (KAD) Mill design consists of a rotating spherical grinding chamber, which shares the same spherical centre as the shaft-mounted counter-rotating disc assembly. The axis of the disc assembly can be inclined to the axis of the spherical grinding chamber by pivoting the disc shaft about the common spherical centre. The inter-particle energy transfer required for breakage results from particle velocity differentials created by the discs intercepting the rotating mass. Particle size reduction is concentrated in high shear zones, which envelop the outer surface and periphery of the discs. This paper traces the development of the KAD Mill from pilot to commercial scale. Pilot work covers a range of minerals including magnetite, calcite, dolomite, barite, limestone and talc. Test results include open and closed circuit operation in wet and dry modes. Conventional milling constraints and energy consumption issues are addressed while new dimensions are added to the feed size range acceptable for wet and dry grinding to fine and ultra-fine sizes.

Sep 13, 2010

Radio Detection and Ranging is an active form of remote sensing. The-imaging system sends out a source of electromagnetic energy to 'illuminate' the terrain and then records the energy returned. The wavelengths used by radar are in the microwave region and vary from a few millimetres to about a metre. Radar systems are independent of lighting conditions and weather. In addition, targets may be illuminated in the optimum direction to enhance features of interest. New Zealand was one of the principal investigators on the Shuttle Imaging Radar (SIR-B) experiment, part of the payload on Challenger Mission 41-G in October 1984. Data collected over New Zealand was restricted to two very poor quality optical images and one poor quality digital data take. The digital image covered the ranges between the Hawke Bay-Wairoa Basin and the Volcanic Plateau. Variations of texture in this image frequently were indicative of variations in lithology and induration. The image also clearly depicted major faults where these had had a significant effect on the topography.

Jan 1, 1986

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June) 1896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to the works, the fuewoodbeing of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides). The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by, many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall, which averages about 110 in per annum. The areas so far exploited aggregate a total of about42 square miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cubic feet per ton, 60 tons per acre being considered a good average yield. The gross amount...

Jan 1, 1910

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

Differentiation of a basaltic (?) magma occurred in an active volcanic area during the late Miocene and Pliocene, and a change in the general mode of extrusion from fissure flow for the basalt to explosion for the andesite reflects an accompanying increasing magmatic viscosity. A caldera formed after the flow phase was completed and was filled with coarse agglomerate, much of which has a fused appearance. After an erosion interval its shape was modified and it became gradually deeper as repeated explosions from growing andesitic volcanoes caused large quantities of pyroclastic material to be deposited. At the close of this phase the floor abruptly collapsed when a, large block of the underlying crust was engulfed. The incompetent pyroclastics filling the caldera steepened in dip and the ensuing fractures were filled by the rising magma as dykes and sills and a chonolith formed below the caldera at a shallow depth. The ensuing activity reveals a further stage in differentiation and biotite is an important new ferromagnesian to be observed in the new rocks.Fracturing of the surrounding basalts was most intense in the rocks forming the periphery of the caldera where steeply and flatly dipping faults resulted from increasing horizontal pressure directed towards the caldera.Further differentiation resulted in the increased crystallization of orthoclase felspar, as evidenced by the numerous intrusives of trachy andesitic composition. Magmatic freezing caused mineralizers to accumulate at the top of the chonolith. These eventually escaped and auriferous pyrites, tellurides, quartz, and calcite were deposited in the surrounding rocks.The flatly dipping fractures are the most important and can be expected at various depths in a zone about 4,000 ft wide surrounding the caldera. Latest movement along these was controlled by magmatic consolidation rather than the shape of the caldera. Some flat faults were able to remain open during mineralization and acted as a feeder for the shallower fractures, thus limiting the depths to which the steeper dipping fractures were mineralized with the possible exception of one particular Nw.-striking lode (the Crown-Crescent).INTRODUCTIONThe gold deposits of the Tavua district were discovered in 1932 and from 1935 to June, 1961, 1,985,041 fine ounces of gold were produced from 4,202,504 tons of ore. Of the original three producers, only the Emperor remains active in the...

Jan 1, 1962

By J J. Van Wijk, A R. Penney

Successful management of geotechnical risk at a mining operation is more than just having a good ground control management plan or using advanced numerical modelling and the latest monitoring technologies. The fundamental requirements for effective geotechnical risk management include identification of potential failure modes, identifying and implementing appropriate controls, and demonstrating the effectiveness of those controls. Effective geotechnical risk management requires an integrated approach by confirming that appropriate risk management systems have been identified and implemented (management plans, procedures etc), and that these systems are executed consistently in the field across all working areas. Development of a thorough integrated auditing process executed by an experienced team of technical subject matter experts with substantial operational knowledge, provides a more complete picture of catastrophic hazard management. Following consistent evaluation criteria allows benchmarking of systems and implementation compliance between the sites being audited, and the results can then be ranked against other operations in an industry database.

Nov 29, 2022

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE AWARD TO ELLIOTT SYLVESTER TIMOTHY O'DRISCOLLTim O'Driscoll comes from a mixture of Irish and Scottish stock. His family on the paternal side settled on land in Western Australia in the middle of the last century. His family on the maternal side were part of the W.A. goldfields scenc, including places such as Kanowna, and the Great Fingal mine, near Cue, where his grandfather lies buried.The combination of land and mining environments may perhaps have contributed to an innate interest in geology shared by Tim and his two brothers, all of whom became geologists.Tim showed an early liking for mathematical and geometric subjects, and in his B.Sc. studies at the University of Western Australia he took a major in mathematics along with geology in 1940.His first job was on the Kalgoorlie Golden Mile, and then at Norseman. After serving as a flying boat navigator in the north and south Pacific theatres in World War II he returned to Kalgoorlie and thence to Broken Hill.

Jan 1, 1977

By Selby J

South Australia's economic development has relied heavily on the mineral industry. In the late 1840s the rich copper deposits at Kapunda and Burra saved the Colony's economy when South Australia became a world copper producer. Copper lodes developed at Moonta-Wallaroo during the 1860s brought further prosperity when mining activities at Kapunda and Burra were in decline. In addition to those large mines there were many smaller workings scattered through the Flinders and Mount Lofty Ranges producing copper, gold, silver, lead and zinc. Most of the mines of this period were worked by Cornish immigrants who brought their own technology and mining methods with them. These people have left a cultural legacy unique in Aus- tralia. In this Jubilee 150 year (1986) the Department of Mines and Energy, working in conjunction with the Department of Environment and Planning, is helping to preserve and interpret selected historic mining sites, most of which have been neglected since their closure. This work is designed to draw people's interest to mining history by providing interpreted sites for them to visit and to demon- strate the importance of the mining industry in South Australia's cultural and economic develop- Ment.

Jan 1, 1987

R. C. BUCKETT (Lake View and Star Limited) : At the outset I should like to add my congratulations to those already extended to Mr..Norwood on his excellent paper, which has given us all an inspiration to strive further to improve our plant recoveries. In some respects this paper has left us so little to discuss without considerable time spent on. further research work. At all points one is met by a baffling array of facts which leave one feeling hesitant to speak.The careful and methodical way in which Mr. Norwood went along step by step until all channels of research presenting themselves were tested to his own satisfaction leaves me with but a few comments to make. Particularly striking to me is the explanation of the residual gold values in calcines by recrystallization of haematite and here is a line to be attacked by future studies. This will be mentioned again later.Particularizing on the paper, the first point that struck me was the method of change of pyrite through to the final haematite. I have never been able to satisfy myself that a sample taken from various positions along a roaster when cooled, as described on p. 397, represented a fair sample of the conditions at that point, but I must confess that I have not found a substitute that did satisfy me.However, the following figures are illuminating... But to fill dry a receptacle of known volume with calcines, as described by Mr. Norwood, gives the following apparentspecific gravities:

Jan 1, 1940

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

COMPRESSED air is held in high esteem by the mining engineer as a medium for the transmission of power. The transmission, however, is accompanied by a high percentage of loss. Of the total work done by the steam cylinder'in compressing the air inthe air cylinder, less than 50% is ultimately utilized by the machines underground. These losses are due to its essential and inherent properties as a gas. One of the sources of loss is that due to transmission through the pipes which distribute the air from the receiver to the various places where it is used. As the capacity and economic design of air-compressing plant are influenced by this source of loss, it may be of interest to give an outline of how estimates may readily be made'in practice of thediameter of pipes, quantity of air discharged, and the drop in pressure occasioned.In hydraulics we have a general formula given M Rankine's "Civil Engineering" :It was suggested, the writer believes, in the first instance by D'Arcy, that this formula could be made to apply to an elastic...

Jan 1, 1918

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u'ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

By S F. Simmons, J Fleming

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyilite alteration zone forms an upward flaring cone, largely hosted within a breccia body that cross-cuts the Co, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid-mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

The necessity for good management and economic working in our mines and ore-dressing sheds is impressed upon us by the present low prices of all our metals. Silver, lead, copper, and tin have all suffered a heavy decline during the last six or twelve months, and many mines have been shut down simply on account of the low market value of the ore produced. After fully considering the position of the mining industry. I am convinced that considerable improvements will have to be made to make it as prosperous as it ought to be. The most obvious of these improvements are good management, good machinery, and as little interference by directors as possible. If these conditions are insisted upon and carried out efficielltly a poor mine may have a chance to weather the storm.There is no doubt that the present depression is the refilult of over-speculation and general loss of confidence by which the whole commercial system has been affected, and every branch has suffered more or less, mining not excepted. It has suffered heavy losses in the past, and the future is not over bright we are, therefore, compelled to be careful in everything by which mining is affected and savings can be secured.

The Phoenix mine on the Mararoa Reef at Norseman, Western Australia, provides an outstanding: AUstralian instance of the recurrence of payable ore beneath the bottom of an abandoned mine, and an interesting and instructive example of the development ofideas with regard to ore recurrence in a particular district. The Mararoa Reef is the most productive of several hypothermal goldquartz vains in pre-Cambrian basic volc81olics which strike northsouth and dip on the average, 45 degrees east. The Phoenix minewas abandoned at 500 ft. vertical depth after producing 342,000 tons of 9.9 dwt. recovery grade (equivalent to nearly half of the total production of the Norseman field) from a 2,500 ft.. long, horizontally disposed oreshoot, which is reported to have had an ore outcrop only 30 ft. in length.Interest in the field was revived in 1933, and by 1941 new ore mined and developed on the Mararoa Reef by Central Norseman Gold Corporation N.L. amounted to approximately 700,000 tons of 6.7 dwt. recovery grade. In the same period another oreshoot of similar size and grade was developed by Norseman Gold Mines N.L., south of the old Mararoa company's site. As shown by the plans, the ore occurs in discontinuous shoots. The intervening area of shear is poor in quartz as well as in gold. Geological work on behalf of Western Mining Corporation Ltd., and Central Norseman Gold Corporation N.L. has been in progress in the mine and in the field more or less continuously from 1913 to 1941 and again since 1946. This paper describes the successive advances in the understanding of the exploratory problem up to late 1941, to which several investigators have contributed. It is published by permission of the Board of Directors of Central Norseman Gold Corporation N.L., owners and operators of the Phoenix and other mines.Development of the Prospect.In 1933 Western Mining Corporation acquired an option over the Phoenix property and adjacent leases. H. E. McKinstryl visited the mine and recognised that the ore occurred primarily on the flatly dipping sections of the vein, as distinct from the steeply dippingsections, in a wide shear zone with reverse movement. Many of the flatly dipping fractures were seen to exhibit tension phenomena and to link one shear plane to the next below on the footwall side. The flat links carried much more quartz than the steeper shears.Later, H. J. C. Conolly, assisted by J. D. Campbell, examined the prospect and by contouring the vein with reference to an inclined...

Jan 1, 1950

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010