Search Documents

By Reno Sales

THE present-day application of geological knowledge to mine opera-tions owes much to Survey activities. Early publications covering developed deposits at Comstock and Eureka in Nevada, and Leadville in Colorado, aroused great interest in mine geology among mine owners and operators. In later years personal contacts between Survey geologists, notably Lindgren, Spurr, Emmons, Weed, and Ransome, to name only a few, and mine managers, mine superintendents and mine foremen, brought directly home the importance of geological mapping and study in connection with mine operations. However, the Survey had recognized from the beginning that it was not practicable, either from the viewpoint of cost or policy, to supply direct help to the miner. The situation was met by many large mining companies through the organization of geological departments to deal with problems of geology which concerned not alone the every-day mine operation but also the life expectancy of the ore deposit. The mine owner therefore looked to the mine geologist to apply the "laws of ore deposition" in estimating the future of his mine. The examination of outside properties also became a duty of the company geologist where replacements were needed or where expansion of operations was contem-plated. And finally, out of this situation there developed the inde-pendent consulting geologist, specializing in geological examinations of prospects, mines, and mining districts, whose duties included the highly important but often difficult task of appraising ore reserves and ore possibilities. Thus, while it may be considered by many that the work of the mine geologist overlaps that of the Survey geologist, their respective fields of endeavor are not in conflict. The appearance of the mine geologist has lessened in no manner the need of intensive field and research work by the Geological Survey and related organizations.

Jan 1, 1934

By John D. Ridge

For mining geologists, the most important trends during 1962 have been the increased concentration of the exploratory activities of American mining companies in the United States and Canada and the greater use of the combined techniques of geology, geophysics and geochemistry in searches over larger areas for wider varieties of metals and minerals. The principal reasons for these changes in approach have been the deterioration of the political-economic climate in many areas of the globe of equal or greater geologic promise and the realization that modern exploration is most efficiently and economically conducted through the use of all available means of detecting ores in areas sufficiently large to raise to a maximum the chances of success. The attitude of certain major U.S. metal-producing companies can be shown by the officially ex- pressed positions of their principal officers. Early in 1962, Clyde E. Weed, Chairman of the Board of Anaconda, remarked that "because of unsettled conditions and disruptive influences in many of the copper-producing areas of the world, it is imperative that domestic copper-producing capacity be improved and made as efficient as possible in order to meet consumer demands at reasonably stable prices." In November, Robert G. Page, President of Phelps Dodge, pointed out that his company is not only concentrating most of its exploratory effort on this continent but is also increasing the number of metals for which it is searching. Frank R. Milliken, President of Kennecott, recently said that "most of our exploration money is going into the northern part of the Western Hemisphere."

Jan 2, 1963

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Herbert Hoover

THE desire of the engineers over the last few years, growing out of their contact with public affairs, that this Institute should take a wider vision than the narrower field of technology and should apply its skill to the development of civic problems which must lay in their foundation on engineering, has led to this discussion today. Some of us in San Francisco, in discussing this question of the relation of the engineers to civic problems, raised the question as to whether or not in this national emergency it was not the duty of the Mining Engineers to bring, forward their combined skill and knowledge and experience to bear upon the problems of the coal industry. This industry, considered as a whole, is one of the worst functioning industries in the United States. It is equipped with capital, with machinery, plants and labor to a peak load at least 20 per cent. above the average necessity. This peak load, therefore, involves the use of probably 100,000 men diverted from other productive industries; it involves an intermittency of employment through its whole personnel that results not only in a long train of human woe, but results also in a higher cost of coal -to the general public. The problem of whether the industry can, by any device, be cured or even partially cured of its intermittency, is solely an engineering problem. It is therefore an apropos problem for this Institute. Your President and myself and others thought that we could best develop this discussion by calling upon men of large experience in the particular branches of the soft coal industry, to bring the facts in front of this general committee, with a view to an exhaustive discussion and perhaps subsequently the appointment of a committee to formulate those facts and such remedies as may be developed into a report that would be of constructive value.

Jan 3, 1920

By R. L. Fleischer, B. Chalmers

In order to observe size effects associated with a grain boundary, aluminum single crystals and bicrystals of various cross-sectional dimensions were deformed in tension. Typical stress-strain curves are presented in conjunction with measurements of the effects of changes in crystal dimensions. Some effects of the growth rate used in preparation of crystals are also described. It is indicated that the macroscopic constraints at a grain boundary are responsible for the most prominent grain-boundary effect, the production of multiple slip. Two measurements of the width of the region of double slip are in agreement. It is concluded that the yield stress of aluminum is affected markedly by the inherent oxide coating. THE general problem to be examined is that of dimensional effects in the plastic deformation of metal crystals. These effects will be termed "size effects" and are here defined as follows: A size effect occurs in a series of crystals if their plastic-deformation properties are a function of crystal dimensions. Clearly then size effects depend on the nature of the boundary conditions imposed on the crystal. Crystal boundaries can be of three types: interphase, inter-crystalline, and free surface. Such deformation effects as are caused by distribution of phases, grain size, lineage structure, and single crystal external geometry are specific types of size effects. This discussion will be confined primarily to grain-boundary and single-crystal size effects, though in practice most "single crystals" not only have a number of small angle boundaries but also have one or more surface phases, so that the boundary conditions appropriate to a free surface do not necessarily apply. Hence, to this extent interphase size effects will be considered. The question of size effects associated with grain boundaries (called here intercrystalline size effects)

Jan 1, 1959

By J. L. Huitt, B. B. McGlothlin

The introduction of new fracture propping agents that are brittle but much stronger than sand created the problem of what loading strength is required for a propping agent to be effective in a given formation. It is shown that the load at which the propping agent crushes should exceed the load at which total embedment in the fracture faces is possible. Simple laboratory tests to determine loading strength of the propping agent and embedment in the fracture faces, and use of these data in selecting a propping agent for a given formation, are discussed. INTRODUCTION One of the most important factors in the design of hydraulic fracturing treatments is the selection of a propping agent that can effectively provide the fracture flow capacity needed for stimulation of a well. Sand, once generally accepted as being synonymous with propping agent in hydraulic fracturing, is now recognized as having limited effectiveness in many formations because of its low resistance to crushing. Sand particles are brittle and have relatively low strength. Because of this property, sand particles are crushed in rocks that offer high resistance to the penetration of fracture faces by the proppant particles when the fracture attempts to close under the action of the overburden load. For rocks that offer a high resistance to penetration, deform able particles are more effective propping agents than sand. However, for this same type of rock, a propping agent that does not deform, yet does not crush, is often more effective. Thus, a rigid propping agent with sufficient strength to prevent crushing is desirable. A method for determining the strength required for a rigid propping agent to function effectively in given formations is discussed. BEHAVIOR OF RIGID PROPPANTS AND FRACTURE FACES RELATED STUDIES An early qualitative description of the reaction of propping sand in fractures was given by Hassebroek et al.' In discussing fracturing in deep wells, the authors mentioned that even though propping sand entered the fractures, a high flow capacity did not result due to crushing or embedding of the propping sand. Dehlinger et al.2 in discussing the reaction of propping sand surmised that, because of the hardness of sand particles, deformation occurred in the fracture faces contacting the propping sand. In later studies,3,4 methods of determining the embedment of propping sand in fracture faces of soft rock and the critical load at which propping sand is crushed by the fracture faces in hard rock were discussed. In working with de-formable proppants, Kern et al. considered proppant particles to be deformed into cylindrical disks by action of the overburden and then pressed slightly into the fracture faces by further action of the overburden. Rixie et al.'0 reported on embedment pressure and presented a method of selecting a propping agent for use in given formations. The propping agents included sand, walnut shells and aluminum pellets. All these studies have contributed materially to a better understanding of propping agent behavior; however, the strength of brittle proppants (sand, glass and ceramics) required to result in embedment rather than crushing has not been discussed. This topic will be covered in the ensuing discussion. PROPPANT PARTICLE CRUSHING—-EMBEDMENT For this discussion, a rigid propping agent is considered to be one that is brittle and fails under tensile stress when loaded to a critical value. In an earlier study4 it was shown that the Hertzian4 loading theory could be applied to a spherical brittle propping agent if the propping agent and fracture faces behaved elastically. At the failure of the proppant, the ratio of the load to the square of the diameter of the particle should be constant for a given material combination, or: Lc/dp2=C ............(1) A partial derivation of this equation from proppant and formation properties is included in the Appendix. Should a rigid particle not be crushed as a load is applied, it embeds in the fracture faces. A study3 of particle embedment in fracture surfaces has been published. The embedment can be described by an equation based on Meyer's metal penetration hardness relationships: d1/dp=B 1/2[L/dp2]m/2..........(2) In Eq. 2, B and m are constants that are characteristic of the rock; the significance of the other terms is shown in Fig. 1. A STANDARD DEFINITION FOR PROPPANT LOADING STRENGTH Eq. 1 is useful in appraising propping agent strength," but it is strictly applicable only when the area of contact between a particle and a fracture face (or loading plate)

Jan 1, 1967

By W. A. Backofen, M. L. Ebner

SINCE the early work of Gough with Hanson and Wright,l-3 the study of fatigue has been characterized by experiments on single crystals only in recent times.9-10 Now, increasing attention is given to this aspect of fatigue research for the insight that it may provide into details of mechanism. The investigations have concentrated to a large extent on the development of deformation markings on fatigued crystals, and have shown the cracks to originate in slip bands possibly preceded or accompanied by slip-band extrusions. Experiments of special interest to the present work were conducted by paterson5 on copper crystals and involved both metallographic examination and measurement of change in flow stress. Crystals were cycled in alternating tens ion-compress ion with a constant plastic shear-strain amplitude of approximately 0.8 pct, and were particularly revealing for their demonstration of hardening with accumulated strain similar to that in unidirectional straining, through an easy-glide stage I followed by a stage II of rapid hardening; deformation was not continued beyond 40 cycles, however, so that the eventual course of the hardening curve could not be decided. For the conditions used by Paterson, surface slip markings were similar to those observed in unidirectional straining, but there were no X-ray asterisms and no deformation bands on the surface. In current thinking about the nature of fracture in fatigue, two views relative to mechanism are generally acknowledged, with the reservation that both could apply simultaneously in some measure. As one possibility, fracturing across a slip plane is regarded as a result of loss of cohesion from the creation of many point defects by dislocation movement under the cyclic loading.'' On the other hand, fracture has also been taken to follow as a consequence only of the geometry of slip at a free surface, consisting of offsets and crevices which eventually become fatigue cracks.12, l3 The work of McCammon and Rosenbergl4 showing fatigue in polycrystals at 4.2oK makes clear that any long-range diffusion of point defects is unnecessary, yet studies such as those of Forsyth and stubington15 show that accelerated diffusion may be a characteristic of deformation under fatigue loading. Interest in obtaining data of possible use for resolving such questions led to the experiments described below. Copper crystals were conveniently loaded in alternating four-point bending at constant deflection, a test condition shown to approximate a constant plastic strain amplitude for a wide range of axial orientations. The method of testing was not readily adapted to extensive study of temperature effects, but an investigation of the geometry of crack formation could simply be made by orienting,the slip direction at different angles to the surface. EXPERIMENTAL PROCEDURES Single crystals were grown by a modified Bridgman method in a stationary gradient furnace under an atmosphere of purified dry nitrogen. Purity of as-grown crystals was 99.999 pct as determined by spectrographic analysis plus vacuum fusion and gravimetric analyses for oxygen and sulfur, respectively. Crystals were of reasonable perfection as evidenced by a critical resolved shear stress at 10 deg from (110) of 60 g per sq mm and half-width of a (400) X-ray diffraction line from one crystal of

Jan 1, 1960

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

EXPERIMENTAL results of the last decade have shown that both accelerator particles and reactor radiations produce significant changes in the properties of metals. These changes, called radiation damage, are important from both academic and engineering viewpoints. An understanding of the radiation damage produced by reactor radiations is difficult, because many kinds of particles having varying energies are present. Therefore, many fundamental studies are being conducted using accelerators in order to obtain nearly mono-energetic beams of various charged particles. Furthermore, many of these experiments are conducted at low temperatures in order to freeze in the radiation-produced lattice defects, after which the specimens are annealed to study the movement of the defects. It is found that although much of the low temperature radiation damage disappears by annealing at room temperature, a significant amount remains. Because there is no assurance that irradiation followed by annealing at a higher temperature will produce the same effect as irradiation at the higher temperature, and because there is an immediate interest in reactor radiation effects during exposures at and above room temperature, a major program is in progress at this laboratory to investigate some of these effects. This paper, representing a part of the program, compares the radiation damage to a group of metals which were exposed under nearly identical irradiation conditions. The metals, representing the three major crystal systems, include copper, nickel, titanium, zirconium, iron, molybdenum, and type 347 stainless steel. The effects of reactor radiations have been treated from a theoretical viewpoint by Seitz' and Ozeroff.' The problem considered by them has been the atomic displacements produced in an infinite medium by mono-energetic beams of both neutrons and charged particles. For reactor experiments, this treatment is not wide enough in scope, because specimens and reactor components are finite, and there are continuous energy spectra of the various particles. Therefore, the theoretical considerations will be extended in this paper to cover reactor conditions and the findings will be compared with the observed radiation damage. Experimental Materials—The six basic metals for this investigation were of commercial or higher purity, and the type 347 stainless steel was of commercial quality. These materials were supplied in various forms ranging from ingots to finished rods, and were fabricated to rods approximately % in. in diam and annealed for specimen stock. A summary of data pertinent to these materials is shown in Table I. The values for chemical compositions include both actual analytical values and typical values supplied by the manufacturer. More information concerning typical

Jan 1, 1957

By S. R. Seagle, R. Schuhmann, N. A. Parlee

Rates of CO evolution and CO absorption were measured for liquid-iron alloys containing from 0.15 to 4.4 pet C, using a modified Sieverts apparatus. The alloys were held in alumina crucibles, so that both crucible-metal and gas-metal reactions occurred simultaneously. The data are interpreted on the hypothesis that the C-O reaction rate is controlled by oxygen diffusion across the boundary layers at the gas-metal and crucible-metal surfaces. CARBON-monoxide evolution from liquid Fe-C-0 alloys is a key reaction in steelmaking processes, both in the steelmaking furnace and in the ingot mold. Also, this reaction probably is an essential step in the desulfurization of iron under blast-furnace conditions, for which carbon is the principal reducing agent or deoxidizer present in the iron. The thermodynamic properties of the solutions of C and 0 in Fe and the equilibria of these solutions with gaseous CO and CO, have been investigated in some detail and are reasonably well understood. However, while these equilibrium data have accumulated in the laboratory, other data have accumulated to show that equilibrium conditions are often not achieved under plant operating conditions. Thus, an understanding of the rate and mechanism of the carbon-oxygen reaction not only has theoretical interest, but ultimately may assume considerable practical importance. Reaction Mechanisms and Rate Equations The over-all reaction under consideration is C (in liquid Fe) + 0 (in liquid Fe) + CO (gas) [I] Although this appears to be a straightforward heterogeneous reaction, involving just two phases (liquid metal and gas), a wide variety of reaction mechanisms has been proposed. Different authors have expressed divergent views as to the nature of the rate-controlling steps. Accordingly, a brief discussion of the possible reaction steps will be given. 1) Homogeneous Reaction Within Liquid Iron— Feild' and Jette2 have applied chemical reaction-rate theory as if the C-0 reaction were a homogeneous, second-order reaction occurring within the liquid-metal phase. This mechanism necessarily produces CO "molecules" dissolved in liquid iron. In order to yield CO gas, the dissolved CO must nucleate CO gas bubbles, and the dissolved CO also must be transported to the bubble surface where it enters the gas phase. However, this mechanism is inconsistent with present concepts of the structure of liquid-metal solutions. 2) Reaction at Gas-Metal Interface—At the surface of contact between gas and metal, a second-order reaction between dissolved C and 0 may occur to produce a CO molecule which enters the gas phase. This reaction presumably involves an "activated complex" structure in the interface. Some such surface mechanism appears essential because the carbon and oxygen do not occur in the same species in the two phases and therefore must react in some way at the surface. At liquid-iron temperatures, calculations based on reaction-rate theory indicate that the surface reaction must proceed extremely rapidly and thus cannot be a rate-determining step in the C-O reaction under ordinary conditions.3 ccordingly when the over-all reaction is measurably slow, the surface reaction may be considered at equilibrium; that is Cc* Co* = m'Pco [2] in which Co* and Co* are the concentrations of carbon and oxygen (weight per unit volume of metal), respectively, in the liquid-metal phase at the interface, Poo* is partial pressure of CO in the gas phase at the surface (atmospheres), and m' is the mass-action constant for Reaction [I]. Since activities of C and 0 are not strictly proportional to concentrations, m' is not a true thermodynamic equilibrium constant but varies with carbon content.' 3) Mass Transport—If the reaction is to proceed at the gas-metal surface, as described above, dissolved carbon and oxygen in the liquid iron must come to the surface and gaseous carbon monoxide must move away from the surface. Details of the mass-transport mechanisms depend on the kind of system under consideration. For a stirred metal bath in contact with a CO gas phase, the transport of C and 0 to the surface can be described by 1 Do Mols CO evolved per sec = — 1/16— Do/do Agm (CO-Co*) = 1/12 Do/do Agm *(Co-Co*) [3] In this equation, Do and D, are the diffusion constants for oxygen and carbon in liquid iron, 6, and 6,. are the boundary-layer thicknesses, A,,,, is the

Jan 1, 1959

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By W. G. Oldham

By monitoring the capacitance of abrupt p-n junctions it is possible to follow the motion of substitu-tional impurities. A p-n junction is formed by growth of silicon from an Al-Si alloy on an n-type silicon sutstrate at a temperature in the range 650" to 750°C. The diodes are etched and sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed to various temperatltres for 10 mm and the capacitance remeasnred. For very heavily doped diodes (-1019 per cm3) observable capacitance changes occur at neutron fluences of >1015 per cm 3. The results may be interpreted in seceral ways, the simplest of which is to assume simple vacancy diffiision with small impurity -racancy interaction (at the diffiision, i.e. annealing temperature of 700°C). In this interpretation it is found that a typical vacancy makes about 1024 jumps and travels about 10-5 cm before disappearing. The required effective annihilation center density is about 1016per cm3 . Estimates of the vacancy-impurity interaction can be made and the above numbers correctecl, but for arty reasonable assumptions the number of vacancy sinks connot be much reduced. ThE complete annealing of radiation induced defects requires that the vacancies and interstitials either recombine, travel to the surface of the crystal, or travel to an annihilation center, e.g., a dislocation or a precipitate. If the interstitial is ignored except as a possible vacancy annihilation center at low temperatures,* the motion of vacancies may be followed by monitoring the corresponding motion of substitutional impurities. pfister2 has measured the enhanced diffusion of impurities in an asymmetric shallow diffused silicon structure by optically monitoring the junction movement. In these experiments we monitor instead the capacitance of a heavily-doped deep symmetric p-n junction. The sensitivity for this method is several orders of magnitude higher than in Pfister's technique, mainly for two reasons: 1) the junction capacitance of a heavily-doped junction is sensitive to impurity movements in the Angstrom range* com- and 2) the junction may be far from the surface which is a major annihilation center for vacancies. THE EXPERIMENT A p-n junction is formed by the epitaxial growth of silicon from an A1-Si alloy on a silicon substrate at a temperature in the range 650° to 750°C. The technique used is the transport of an aluminum melt through a temperature gradient.4 A 10-mil thick aluminum disc is sandwiched between two silicon wafers and the assembly raised to about 650° C with a temperature gradient normal to the sandwich. After about 8 hr the upper (hotter) wafer has been entirely transported and deposited epitaxially on the substrate wafer. The substrate and overgrowth resistivity are measured with a 4-point probe. The as-grown structure is lapped until the wafer is about 1/2 mm thick with the junction in the center. Contacts consisting of electroless nickel covered by electroplated rhodium are applied to both the p and n sides. The wafer is diced into square dice 1/2 to 1 mm on a side and the dice are etched sufficiently to remove approximately 1 mil of silicon. The following results are all for aluminum (p-side) and antimony (n-side) doped specimens with NA =3x 1018 per cm3, ND = 2-8 x 101A per cm3. The diodes are sorted for consistent V-I and capacitance behavior and separated into groups. After irradiation, each set with an unirradiated control set is annealed and the capacitance remeasured. A special capacitance measurement method is used to insure a low sensitivity to shunt resistance. The diode is voltage driven and the current monitored by a phase lock amplifier. It is possible to adjust the detector phase to a point where shunt resistances as low as 100 O have no effect on the reading. The diodes in this study have a capacitance in the range 1000 to 5000 picofarads and a shunt resistance in the range 100 to l06 O depending on the stage of the anneal. THEORY The theoretical problem is twofold: 1) The computation of the amount of impurity diffusion and hence the impurity profile resulting from a given amount of vacancy motion, and 2) the computation of the capacitance from the impurity profile. A comparison of the theoretical and experimental capacitance (in particular the changes) yields the amount of vacancy motion. Vacancy Motion. A convenient parameter to measure the total amount of vacancy motion is Jv the total number of vacancy jumps per unit volume. Although this parameter varies with position in the crystal, owing to vacancy annihilation at the surfaces, it is approximately independent of position far from the surfaces, i.e. in the junction region. In terms of the number of vacancies per unit volume Nv and the vacancy diffusivity given by

Jan 1, 1970

By C. A. Heiland

I. Description of reflection equipments.................. 412 A. Design features of present types.................. 412 B. Reflection equipment designed by writer.............. 418 11. Characteristics of reflection seismographs............... 421 A. Types of coupling in electromagnetic seismographs.......... 421 B. Action of pickup, amplifier and galvanometer............. 424 C. Combined action of pickups, amplifiers and oscillographs....... 433 D. Static and dynamic constants................... 434 E. Desirable values for static and dynamic constants.......... 435 111. Calibration of reflection apparatus.................. 442 A. Dynamic tests without shaking table................ 442 B. Calibration methods....................... 445 C. Various other tests........................ 451 INTRODUCTION In the past five years, the reflection method of seismic prospecting has been developed to a high degree of perfection. Its success in mapping oil structure is due to the unique and definite nature of the depth data obtained. While articles on the principle and results of this method continue to appear in increasing number, there is virtually nothing published about the instruments used in this work. Several years ago, the writer started an experimental and theoretical investigation with the object of determining which characteristics would be best adapted to the problem at hand. As a result, an equipment was developed which has proved its usefulness in a great number of field tests. W. E. Pugh, now with the Empire Oil and Refining Co., joined the writer, in 1931 and 1932, in the laboratory experiments and field tests. In 1933, a paper was written on Certain Instrument and Field Problems in Reflection Seismology, and submitted to the Institute. The part of that paper dealing with field tests was published as Contribution 34 (reprinted in this volume, p. 455). Since then, considerably more labora-

Jan 1, 1934

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-' the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:' and, if some simplifying assumptions about particle shape are allowed, the total number of particles.'2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.' Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By S. S. Marsden, S. A. Khan

Externally generated foam was injected continuously into short porous media. Both flow rate and pressure drop were measured. Liquid saturation was determined by electrical conductivity. Foam yuality I, expressed as the ratio of gas volume to total volume, was varied from 0.70 to 0.96. As measured with a modified fann VG Meter, apparent viscosity of this foam µa decreases with increasing shear rate but usually falls within the range of 50 to 500 cp. At a given shear rate, µa increases almost linearly with I-. When measured with a Bendix Ultraviscoson, kinematic pa is independent of V but absolute pa increases with T from about 3 to 8 cp. The effective permeability -apparent viscosity ratio ke/µa decreases almost linearly with V for porous media of high permeability, but the rate of decrease becomes less for tighter ones. The relative permeability-apparent viscosity ratio kr/µa us V data does not fall on a single line. The kr/µa ratio increases with liquid saturation in the porous medium and with surfactant concentration. Estimates of pa for foam in porous media vary from 30 to 100 cp. INTRODUCTION Although research on the development of a foam-drive, oil recovery process has been going on for almost a decade, most of the significant publications have appeared within the last several years. This illustrates well the rate at which interest in this process is accelerating. Bond and Holbrook 1 were the first to describe the use of foam to improve oil recovery in their patent of 1958. They proposed that an aqueous foaming agent slug be injected into the formation and that this be followed by gas to produce a foam in situ. Fried 2 studied the injection of foam into porous media which had already been subjected to conventional gas or water drives and found that gas could be used to drive a foam bank which would, in turn, displace additional oil in the form of an oil bank. He attributed the increased oil recovery to the high effective viscosity of foam flowing in porous media. His microscopic observations showed the importance of foam generation and regeneration within the porous medium. By injecting both air and aqueous surfactant solution, Bernard3 generated foams within the porous medium in which oil displacement was being studied. In a separate empirical test, he also measured the dynamic foaming characteristics of the same surfactants in water and/or oil. With some exceptions and for the seyen surfactants studied, there seems to be a qualitative relationship between the efficiency of liquid rlisplacrment and the dynamic foaming testtsed. This relationship was not consistent enough to eliminate the necessity of actual foam flood tests in porous media for surfactant selection. In a study basic to gas storage in aquifers, Bennett4 described the displacement of brine by foam in consolidated porous media. Among other things, he stated that the ability of a surfactant solution to foam is more important than the stability of its foam. The presence of a foam bank between the displacing air and the displaced brine improved both breakthrough and ultimate recovery. In a continuation of this work Kolb5 attributed the great reduction in surfactant solution production rate as displacement by air progressed to a decrease in relative permeability to gas. These several effects reported by both Bennett and Kolb can all be attributed to the high apparent viscosity of foam which was obviously flowing in the porous media. Bernard and Holm6 observed that gas permeability in the presence of foam was much less than in the absence of foam when both were measured at the same gas saturations. This reduction in permeability was proportionately greater for more permeable sands and sandstones than for the less permeable. Viscosities of the surfactant solution and air were used for their calculations rather than apparent foam viscosities. The foam stability increased with decreasing permeability, which was probably due to the natural regenerative properties of porous media, and the permeability reduction increased

Jan 1, 1967

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By Harmon F. Fisher

In the course of a comprehensive investigation for the development of the electrical process for the dehydration of oil-field emulsions, the writer has had an unusual opportunity to direct and execute a number of related, parallel studies concerning crude oil emulsions and extending over a period of nearly six years. Among these was an investigation utilizing the microscope for studying both the general characteristics of crude oil emulsions, the nature of their electrical charge and the action of an alternating current field in causing coalescence of the finely dispersed, more or less permanently suspended, emulsion particles into larger droplets of such mass that subsequent dehydration would follow by the ordinary process of settling, further agglomeration of the water droplets and, finally, separation into commercially dry, pipe line oil and a clean water discharge. It is not the purpose of this paper to enter into a detailed discussion of the highly specialized subject of microscope technique, nor into a theoretical discussion concerning the origin of the electrical charge on the emulsion particle or concerning the mechanism of the electrical phenomena occurring during the electrical treatment of oil-field emulsions. In a short paper of this character one can hope to touch on only a very limited discussion of the theoretical aspects of crude oil emulsions. The subject of emulsions and colloids is comprised in a comparatively young science in which, however, very rapid progress is being made and consequently it is undergoing many changes; a tentative conclusion valid today may be overthrown tomorrow. Nor would it be a simple science even if it were no longer undergoing this rapid progress; a thorough study of emulsions is based upon a knowledge of such fundamental subjects as molecular structure, ionization and other electrical phenomena, surface chemistry, surface and interfacial tension phenomena, viscosity and other factors too numerous to discuss here and the fundamental theories of which are still undergoing more or less change. Therefore this paper will confine itself largely to a generally descriptive discussion, a sufficiently detailed outline of the microscope technique and a brief comment on

Jan 1, 1931

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside ; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920