Search Documents

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By Charles L. Mantell, Kurt Straler

The hydrogen reduction of Cr2O3 to chromium metal was found to be feasible at very low water-vapor concentrations, corresponding to dew points of -38° to -24°C, over a temperature range of 1130" to 1490°C. Hydrogen reduction under these conditions was predicted by the calculated equilibrium curves which also indicated that CrzOs is reduced directly to chromium without forming the intermediate oxide, CrO. This reduction path was confirmed by X-ray diffraction analysis. The percent reduction of Cr2O3 at each reaction temperature was constant with time, suggesting an inhibiting effect of water vapor. A small increase in the residual water-vapor concentration of a single temperature, 1490°C, strongly retarded the rate of reduction This effect was expressed by an empim'cal equation which indicated a direct relationship between "distance from equilibrium" and the rate of reduction. me effect of temperature over the range of 1130" to 1490°C was expressed in an Arvhenius plot of log rate vs reciprocal absolute temperature. From this curve the apparent enthalpy of activation was found to be 29,600 cal. Based on the hypothesis that the rate of reductiun is contvolled at the oxide-metal interface, an over-all rate equation consistent with the experimental data and the thery of absolute reaction rates was formulated. A simplification of this expression to an Arrhenius equation was justified by the overriding effect of temperature on the rate of reaction for the minimum water-vapor concentration range. MOST of the metals in Subgroup V1 of the periodic table can be prepared commercially by direct reduction of their oxides by hydrogen or carbon monoxide, at temperatures considerably below the melting points of both the metals and their oxides. Chromium is an exception, being generally reduced from its ore, Cr2O3 . FeO, by silicon in an electric arc furnace which operates above the melting point of the Fe-Cr alloy or above the melting point of chro- mium if a chromium oxide be the starting material. In reduction of chromium oxide by hydrogen, either reduction does not occur at all or the rate of reduction is extremely slow. Theoretical considerations based on the high, exothermic, free energy of formation of Cr2O3 compared to the oxides of the other Subgroup VI metals, molybdenum, tungsten, and uranium, would also suggest a slow rate of reaction and a high activation energy. Interest in the direct gaseous reduction of fine-powdered ores in fluidized beds was considered justification for examination of this reaction. In order to develop a basis for a continuing study of the commercial feasibility of the direct gaseous reduction of chromite, a study of the kinetics of the reduction of Cr2O3 with hydrogen was undertaken. To the authors' knowledge no accurate kinetic data for this reaction have been obtained. Neither has an activation energy been determined nor has an attempt been made to establish a mechanism of reaction. LITERATURE Maier10 compared the data of I. Y. Granaat,6 H. von Wartenburg and S. Aoyama, and G. Grube and M. Flad7 with that derived from calorimetric and ther-modynamic properties for the equilibria for the reduction of Cr2O3 with hydrogen. These results, plotted as the log of the equilibrium constant vs absolute temperature for the reduction of Cr2O3 and the intermediate oxide, CrO, to chromium, show agreement between the differently derived data. In both cases the equilibrium constants were extremely low. Maier showed that, over a temperature range of 1000° to 2000°K, Cr2O3 is more readily reducible than CrO. Granat assumed that CrO was preferentially formed from Cr2o3 above 1100°C. Grube and Flad's analysis of their reaction products in the 895" to 1000°C range indicated the coexistence of only Cr2O3 and chromium. The hydrogen reduction of the other Subgroup VI metals, molybdenum, tungsten, and uranium, shows that reduction of the higher oxide proceeds through all of the intermediate oxides before being reduced to the metal. Since evidence pointed to an anomaly in the reduction behavior of Cr2O3, the authors investigated the reduction path of Cr2Os.to chromium. This was done theoretically with more recently available free-energy data and experimentally by X-ray diffraction analysis. This work reinforces Maier's conclusion.

Jan 1, 1964

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates' have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.' Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By Allan E. Martin, Harold M. Feder, Irving Johnson

The cadmium-uranium system was studied by thermal, metallographic, X-7-ay and sampling techniques; special emphasis was placed on the establishment of the liquidus lines, The single inter metallic phase, identified as the compound UCd11 melts peritectically at 473°C to form a-umnium and melt containing 2.5 wt pct uranium. The cadmium-rich eutectic (0.07 wt pct uranium) freezes at 320.6°C. Solid solubilities in uraizium and cadmium appear to be negligible. Between 473°C and 600°C the liquidus line is retograde. NO publication relating to the cadmium-uranium phase diagram was found in the literature. The establishment of this diagram was of considerable interest to us because of a possible application of the system to the pyrometallurgical reprocessing of nuclear fuels. Analysis of liquid samples, metallographic examination, thermal analysis, and X-ray diffraction analysis were used to establish the phase diagram from about 300° to 670°C. Particular emphasis was placed on the establishment of the liquidus lines. The same system was concurrently studied in this laboratory by the galvanic cell method.' Both studies benefited from a continual interchange of information. MATERIALS AND EXPERIMENTAL PROCEDURES Stick cadmium (99.95 pct Cd, American Smelting and Refining Co.) contained 140 ppm lead as the major impurity. Reactor grade uranium (99.9 pct U, National Lead Co.) was most often used in the form of 20-meshspheres. This form was particularly suitable because it does not oxidize as readily as finer powder. The liquidus lines were determined by chemical analysis of filtered samples of the saturated melts. The liquid sampling technique is described elsewhere2 alumina crucibles (Morganite Triangle RR), tantalum stirring rods, tantalum thermocouple protecthecadmiumtion tubes, Vycor or Pyrex sampling tubes, and grades 60 or 80 porous graphite filters were used. Uranium dissolves in liquid cadmium rather slowly. In order to achieve saturation of the melts it was necessary to modify the procedure of Ref. 2 by the use of more vigorous stirring and longer holding periods (at least 3 hr) at each sampling temperature. The samples were analyzed for uranium by spectro-photometry (dibenzoyl methane method) or by polar- ography. The analyses are estimated to be accurate to 2 pct. Thermal analysis was performed on alloys contained in Morganite alumina crucibles in helium atmospheres. Standard techniques were employed; heating and cooling rates were about 1°C per min. For the determination of the peritectic temperature, Cd-10 pct U charges were first held for at least 50 hr at temperatures in the range 435° to 460°C to form substantial amounts of the intermediate phase. For the determination of the effect of cadmium on the a-p transformation temperature of uranium, charges of Cd-25 pct U (-140+100 mesh uranium spheres) were first held near the transformation temperature, with stirring, to promote solution of cadmium in the solid uranium. The holding times and temperatures for these treatments were 18 hr at 680°C for the cooling run and 28 hr at 630°C for the heating run. Alloy specimens for X-ray diffraction and metallographic examination of the intermediate phase were prepared in sealed, helium-filled Vycor or Pyrex tubes. Ingots from solubility runs and thermal analysis experiments also were examined metallographically. Crystals of the intermediate phase were recovered from certain cadmium-rich alloys by selective dissolution of the matrix in 20 pct ammonium nitrate solution at room temperature. Temperatures were measured with calibrated Pt/Pt-10 pct Rh thermocouples to an estimated accuracy of 0.3°C. However, the depression of the freezing point of cadmium at the eutectic is estimated to be accurate to 0.05°C because a special calibration of the thermocouple was made in place in the equipment with pure cadmium just prior to the measurement. EXPERIMENTAL RESULTS The results of this study were used to construct the cadmium-uranium phase diagram shown in Fig. 1. This diagram is relatively simple; it is characterized by a single intermediate phase, 6 (UCd11), which decomposes peritectically, and which forms a eutectic system with cadmium. The solid solubilities in the terminal phases appear to be negligible. An unusual feature of the diagram is the retrograde slope of the liquidus line above the peritectic temperature. The Liquidus Lines. The liquidus lines above and below the peritectic temperature are based on three separate solubility experiments. The data are shown in Fig. 1 and are given in Table I. It is apparent from the figure that the solubility data obtained by the approach to saturation from higher temperatures fall on substantially the same lines as those obtained

Jan 1, 1962

By H. C. Chao, L. H. Van Vlack

Small MnS inclusions with known crystallographic orientations were placed inside powder compacts of low-carbon steel. After the metal was axially campressed with negligible end friction, the deformstions for the metal and the inclusions were compared. The MnS inclusions deformed more when the [100] direction was aligned with the compression axis than when the [111] direction was parallel to this axis. The deformations of the inclusions in the two principal radial directions were equal for each of the above orientations. Inclusions with [110] compression alignments did not deform with radial symmetry. The relative deformation of the inclusion and metal was closely dependent upon the relatiue hardness of the two phases. The relative deformation of the two phases was not sensitive to the rate of deformation. RECENT studies by the authors1.&apos; suggested that the plastic deformation of MnS in steel would probably be highly sensitive to the orientation of the inclusions and to the temperature of the metal. This paper reports an investigation of these factors upon MnS behavior within steel. Manganese sulfide (MnS) possesses an NaCl-type structure and typically has extensive (l10) {110} slip as a separate (noninclusion) crystal.&apos; A secondary slip system, ( l 10) { l l l}, has also been observed where the major slip system is restricted. In general, MnS inclusions must be rated as a highly deformable second phase.3 The amount of sulfide deformation varies, however, with several composition and processing factors. Some of these have been only partially assigned. For example, it is known that minor amounts (<0.01 pct) of silicon within free-machining steels will increase the amount of MnS deformation,4 but the mechanism of the added deformation can only be surmised at the present. Manganese sulfide and steel have sufficiently comparable deformation characteristics so that slip which is started in steel may be continued through the sulfide inclusions and back into the steel if the crystal orientations are favorable.5 A more detailed discussion of previous work on the plastic deformation of NaC1-type crystals and on the plastic deformation of inclusions within a metal is given in Chao&apos;s work.6 EXPERIMENTAL PROCEDURE The manganese sulfide which was used in this study was prepared by previously described methods.&apos; Single crystals of MnS, both as cleavage cubes and as spheres, were oriented within steel powder compacts so that the desired crystal directions were parallel to the direction of axial compression. A four-stage hydrostatic compaction procedure was used and involved the following steps. In the first stage part of the powder was placed in a metal die 1 in. in diameter with a thick (1 in. OD, 5/8 in. ID) rubber liner which had one end plugged. The steel powder was hand-rammed, making it as dense as possible before placing a carefully sized MnS crystal (either as a sphere or as a cube) near the center. The crystal was oriented with the chosen direction vertical; viz., [001], [011], or [111], with the aid of a X10 microscope. A pair of tungsten wire threads 0.020 in. in diameter was inserted along the side of this (&apos;core compact" to locate the desired plane after the compression tests. After the crystal was positioned in the center of the die, more powder was added and carefully rammed by hand. The die was then capped with a rubber plug of the same hardness and thickness as that of the liner. The whole assembly as shown in Fig. 1 was compacted by a ram load of 54,000 lb (about 70,000 psi). In the second stage a smaller, 3/4-in, rubber-lined die was used to give a stress of approximately 120,000 psi. The above process was repeated with the initial compact serving as a core for a larger compact. The final product after sintering was a cylinder 1 cm long and 1 cm in diameter, having a density of 7.54 g per cu cm. This was close to the theoretical density since the metal contained a non-metallic phase. There was no evidence of MnS deformation during the hydrostatic compaction or subsequent sintering. Elevated-temperature hardness data were obtained by procedures previously described.2 Compression tests for inclusion deformation utilized the cylinders which were described above. The critical problem in these tests was the lubri-

Jan 1, 1965

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe&apos;s formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade&apos;s exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,&apos; catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.&apos; have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By T. I. Moore, L. A. Painter

THE electrolytic zinc plant of the American Zinc Co. of Illinois was described by Davidson&apos; in 1944. Since then, improvements as well as expansion of the plant facilities have been made. In order to increase the production of high grade zinc which was needed for war purposes, an expansion program designed to double the slab zinc capacity was started in 1942 and completed in March 1943. This expansion was propagated by a contract between the American Zinc Co. of Ill. and the Defense Plant Corp. The contract included the facilities of the Fairmont City, Ill., property of the American Zinc Co., where a suspension-type roaster with contact acid plant, cadmium distillation furnace, Waelz oxide and densifying plant, and horizontal retort furnaces were installed. The expanded Monsanto, Ill., plant and the additional facilities of&apos; the Fairmont plant were designed to integrate the metallurgical treatment of zinc concentrates for the production of special high grade zinc at Monsanto with the production of acid, cadmium, high grade zinc from furnace skimmings and the Waelz treatment of leach residue at Fairmont. In general, the original flowsheet was not changed, except for the addition of the filtering, drying and reclaiming of leach residue, and the treatment of purification cake for the recovery of copper, cadmium sponge, and zinc. Fig. 1 is a flow diagram of present operations. The original plant facilities, desi-gned for 50 tons daily production of slab zinc, had some units which were more than adequate. Therefore, in expanding the facilities to 100 tons per day, it was not necessary to double all operating components. Table I gives the comparison of the changes made in the unit operating components for the original facilities, 1941, the 1943 expansion, and the 1951 facilities. During the past 11 years a number of improvenients have been made resulting in: 1—an increase in slab production, 2—higher recoveries on the calcine treated, 3—better quality of slab zinc produced, 4—higher current efficiencies, and 5—less man hours Table I. Changes in Operating Facilities Operating Unit 1941 1943 1951 Calcine unloading (pneumatic), 10 tons per hr 12 calcine unloading track hpr. and elev., 60 tons per hr 1 Calcine storage, tons 1,000 2,000 2,000 Leach tanks, 35 vol. tons. No. 3 5 6 slurry mixing 6x6 ft stainless tank, No. 1 Ball mill. 4.5 rt x 16 in. conical. No. 1 CLassifier duplex, No. 1 1 Thickeners. 50 it diam. No. 2 9 2 Filter thickeners, sq ft &apos;-- Moore filters, sq ft 5.760 11,520 Drum filters, 10 ft diam x 16 ft, No. 3 3 Rotary arlers, No. 1 2 1st stage Cu-As purificatlon tank. 90 vol. tons, No. 3 Solution heaters, No. 3 Filter press, 30x30 bronze, No. 4 Zinc dust purification tanks, 45 vol tons. No. 3 5 4 Filter press, 36x36 bronze, No. 3 5 3 Cadmium recovery plant: Process tank. No. 5 2 Cake roaster, 20 ft diam x 4 hearth. No. 1 Filter press, 24x24, No. 4 1 Sponge wash box, 4x6 ft, No. 1 Evaporative cooling unit (vacuum), No. 1 Purified storage tank, vol. tons 400 400 400 Cell acid storage, vol. tons 400 400 400 Electrolytic cells, No. 180 372 372 Cell room ventilation, cu ft per min 35,000 125,000 125,000 Cell cooling water. gal per min 1,500 2,300 2,300 Deep well 16 in. x 95 ft, 1500 gal per min, No. 2 3 3 Melting and casting furnace, 130 ton. No. I Furnace fume scrubber unit, No. 1 Dross drums, No. 2 Dross roaster, 8 ft diam x 8 hearth, No. 1 Electrolysis power conversion, kw 6,250 23,750 23,750 Power transformers, 13,800/440, kva 1,000 1,500 2,000 Steam boilers fire tube, 15 psi, lb per hr 12,000 18,000 18,000 Steam boilers water tube. 125 psi, Ib per hr 30,000 Air compressor, 2 stage. 300 cu ft per min. 100 psi, No. 1 2 Air compressor, 1 stage, 300 cu ft per min, 20 psi, No. 1 Vacuum pumps, 18x7, 720 cu ft per day, No. - - . Vacuum pumps, 24x11, 1.633 cu ft per day, No. 3 3 Building area, sq ft 60,854 113,568 115,000 per ton of metal produced. In the summer of 1944, the "reverse" leaching process was placed in operation and since it has been described,&apos; no further description will be given. Other facilities and changes which have contributed to the process improvements were the scrubbing of fume from the melting and

Jan 1, 1953

By N. A. Gokcen, John Chipman

SILICON is the most commonly used deoxidizer and an important alloying element in steelmak-ing; hence a detailed study of this element in liquid iron containing oxygen is of considerable interest. The equilibrium between silicon and oxygen in liquid iron has been studied by a number of investigators but generally with inconclusive or incomplete results. The variation of the activity coefficients of silicon and oxygen with composition is entirely unknown. Published investigations deal with the reaction of dissolved oxygen with silicon in liquid iron and the results are expressed in terms of a deoxidation product. For consistency and convenience in comparison of the published information, the deoxidation product as referred to the following reaction is expressed in terms of the percentage by weight of silicon and oxygen in the melt in equilibrium with solid silica: SiO (s) = Si + 2 O; K&apos;l = [% Si] [% 012 [I] Theoretical attempts to calculate the deoxidation constant for silicon in liquid iron from the free energies of various reactions yielded results which were invariably lower than the experimental values. Thus, the deoxidation "constants" calculated by McCance,1,2 Feild,3 Schenck, and Chipman were of the order of 10, which is below the experimental values by a factor of more than 10. Experiments of Herty and coworkers" in the laboratory and steel plant resulted in an average deoxidation constant of 0.82x10 &apos; at about 1600°C. The technique employed in their investigation was crude and the reported temperature was quite uncertain. The concentration of silicon was obtained by subtracting silicon in the inclusions from the total. Since at least some of the inclusions resulting from chilling must represent a fraction of the silicon in solution at high temperatures, such a subtraction is not justifiable. Results of Schenck4 for K&apos;1 from acid open-hearth plant data yielded a value of 2.8x10-5, which was later revised as 1.24x10 at 1600°C. Similarly Schenck and Bruggemann7 obtained 1.76x10-5 at 1600OC. The discrepancies and errors involved in the acid open-hearth plant data as compared with the results of more reliable laboratory techniques were attributed by these authors to the lack of equilibrium and the impurities in liquid metal and slag, and are sufficiently discussed elsewhere." Korber and Oelsen" investigated the relation between dissolved oxygen and silicon in liquid iron covered with silica-saturated slags containing varying concentrations of MnO and FeO. The deoxidation products obtained by their method scatter considerably, and their chosen average values of 1.34x10, 3.6x10-5, and 10.6x10-5 1550°, 1600°, and 1650°C, respectively, represent the best experimental results which were available until quite recently. Darken&apos;s10 plant data from a steel bath agree approximately with their data at 1575° to 1625°C. Zapffe and Sims" investigated the reaction of H2O and H2 with liquid iron containing less than 1 pct Si and obtained deoxidation products varying by a factor of more than 20. Inadequate gas-metal contact and lack of stirring in the metal bath should require a longer period of time than the 1 to 5.5 hr which they allowed for the attainment of equilibrium. Furthermore, their oxygen analyses were incomplete and irregular and confined to a few unsatisfactory preliminary samples. Their results did indeed indicate that the activity coefficient of oxygen is decreased by the presence of silicon, although they made no such simple statement. They chose to attempt to account for their anomalous data by the unlikely hypothesis that SiO is dissolved in the melt. Hilty and Crafts" investigated the reaction of liquid iron with acid slags under an atmosphere of argon, making careful determinations of silicon and oxygen contents at several temperatures. Despite erroneous interpretation of the data at very low silicon concentrations, their data represent the most dependable information on this equilibrium that has been published. In the range 0.1 to 1.0 pct Si, their data yield the following values for the deoxidation product: 1.6x10-5, 3.0x10- &apos;, and 5.3x10 at 1550°, 1600°, and 1650°C, respectively. The purpose of the work described herein was to study the equilibrium represented by eq 1 as well as the following reactions, all in the presence of solid silica: SiO2 (s) + 2H2 (g) = Si + 2H2O (g);

Jan 1, 1953

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well&apos;s results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. &apos;This means that careful measurements of surges occurring in actual field operations must be made.

By S. Floreen, R. M. Pilliar, H. W. Hayden

The fracture behavior of a 50 pct Cu-50 pct Fe mi-croduplex alloy, laminated composites of copper and iron and an extruded 50-50 Cu-Fe elemental powder composite was studied. Very low ductile-brittle transition temperatures were achieved in all cases, but for different reasons. In the microduplex alloy both the initiation and also the propagation of cleavage fractures appeared retarded by the very small in-terphase distances. In the composites, crack propagation through the sumples was prevented in most cases by delamination fractures perpendicular to the advancing cracks. These delaminations occurred at different regions and by different mechanisms in the various composites. In the extruded powder composite, de-lamination appeared to take place along preexisting flaws. In the crack arrest geometry of the laminated plates, delamination took place by localized shear fractures within the copper near the Fe-Cu interfaces. In this case delamination was enhanced by thicker laminate layers, and by having the resistance to shear failure of the copper sufficiently low compared to the toughness of the iron. BRITTLE fracture in engineering materials has long been a problem, and many different ways of preventing it have been considered. One method that has been of growing interest lately is to prevent crack propagation by the introduction of mechanical discontinuities into the structure. These discontinuities may act in several ways. They may simply act as crack stoppers. They may introduce secondary fractures such as de-laminations that deflect the initial crack into new, less damaging directions. Alternatively, they may subdivide a fairly large bulk sample that would have been loaded in plane strain, for example, into a number of subunits that are individually loaded in plane stress and thus are more resistant to fracture. Other mechanisms, or combinations of mechanisms, are also feasible. A number of methods exist for introducing mechanical discontinuities into a structure. Composites by their nature have discontinuities in structure, and numerous studies have shown that fracture propagation in materials of this type can be radically changed by suitable control of the composite parameters. Of particular significance to the present work are recent investigations of layered composites made by joining high strength steel sheets by various means.&apos;-4 These studies have shown that through proper control of the mechanical properties of the bonds joining the sheets it was possible to introduce delamination fractures that markedly improved the overall toughness of the composites and in some cases completely prevented through-the-thickness fractures. Another technique for introducing structural discontinuities is simply to use a two-phase alloy. It has been recognized for many years that a small amount of a second phase may improve toughness either by homogenizing plastic flow and thus preventing localized stress concentrations that nucleate fracture, or by interacting with an advancing crack. In most of these studies of two-phase materials, the decreases in ductile-brittle transition temperatures produced by the second phase were relatively small. More recently, work on two-phase stainless steels having a very fine grain microduplex structure has shown that the presence of on the order of 40 to 50 pct of a tougher second phase may lower the ductile-brittle transition temperature of the brittle phase by approximately 300°F. 5-7 In these alloys delaminations were seldom observed. The tougher second phase appeared to minimize the ease of both the initiation and the propagation of cleavage fractures. These results show that both the composite approach and the microduplex alloy approach are effective methods of preventing brittle fracture. Therefore, it was of interest to compare the fracture behavior of a microduplex alloy with composites made from the two-phases that were present in the alloy. To simplify this comparison the 50 pct Cu-50 pct Fe system was selected for study. At low temperatures the equilibrium tie line phases in this system are essentially pure ferrite and pure copper. A 50-50 alloy was cast and hot worked to produce a microduplex structure. Two types of composites were studied; laminated structures prepared by roll bonding iron and copper sheets of the tie line compositions, and an extruded powder composite made from high purity elemental powders. The fracture behavior of these materials was then compared. EXPERIMENTAL PROCEDURE Alloy Preparation. The 50-50 Fe-Cu alloy and the components for the roll bonded composites were prepared by vacuum induction melting 30-lb heats using electrolytic grades of iron and copper as charge materials. A carbon boil was used to deoxidize the melts. Small additions of copper and iron were made to the iron and copper heats, respectively, to approximate

Jan 1, 1970

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..&apos; and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young&apos;s modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen&apos;s5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By D. L. Kelley

High-viscosity water injection has been proposed for use in reservoirs containing high-viscosity crude oils. Previous publications have largely ignored the possible effects of the connate water on the proposed process. This paper describes experimental work which indicates that the connate water will be forced ahead of the injected water to form a bank of low-viscosity water. This decreases the oil recovery which would be expected if such a bank were not formed. These effects are shown for a range of fluid mobilities and connate-water saturations for a five-spot injection system. In general, oil recoveries using viscous water are significantly greater than for untreated water even though they are less than would be expected if no connate water bank were formed. INTRODUCTION The effect of mobility ratio on the oil recovery of wa-terfloods has been known for many years. Muskat first pointed out that the fluid mobilities (k/µ) in the oil and water regions would affect the performance of the water-flood, and he estimated the general effect of these variables.&apos; Since this early work, studies of the effect of mobility ratio on secondary recovery have been reported where mathematical,&apos; potentiometric3 and scaled flow models&apos; were used. These studies have shown that a reduction in the mobility ratio between the oil and the displacing fluid would cause additional oil recovery when water-flooding reservoirs containing viscous crude oils. Studies reported by Pye- nd Sandiford 8 have indicated that chemicals to increase injection water viscosity are now available and can be used to reduce the over-all mobility ratio of a waterflood. Where mobility ratios are controlled by the injection of viscous fluids, the connate water of the reservoir can play an important part in the displacement of the reservoir oil. The purpose of this study was to determine the effect of the connate-water saturation in waterfloods where viscous waters are used for injection. DISPLACEMENT OF THE CONNATE WATER Russell, Morgan and Muskat7 were the first to recognize the mobility of connate waters in waterflooding. They conducted waterfloods on oil-saturated cores containing 20 and 35 per cent irreducible water saturations, and found that from 80 to 90 per cent of the "irreducible" water was produced after only one pore volume of water was injected. However, their experiments were conducted at rates of flow significantly higher than those ordinarily occurring in waterfloods. Also, the cores were only from 4.0 to 8.5 cm long. Brown 4 studied a 100-cm linear sand pack which had been prepared to contain connate water and oil. He used 140- and 1.8-cp oils with injection water of essentially the same viscosity as the connate water. He found that all of the connate water was displaced by the injection water in both cases. However, the injection volumes required for complete displacement of the connate water were considerably higher in the case of the more viscous oil. To verify the results of the foregoing experiment, a 10-ft-long linear model was constructed by packing 250-300 mesh sand in a 1/2-in. diameter nylon tube. The model was evacuated, saturated with a brine of 1-cp viscosity, and flooded with a 41-cp mineral oil to the irreducible water saturation of 10.9 per cent. The model was then waterflooded by the injection of a water solution which had an apparent viscosity of 42.6 cp. The solution consisted of 0.5 per cent methylcellulose in distilled water. The viscosities of the oil and connate water were measured with an Ostwald viscosimeter. The viscosity of the polymer solution was calculated by Darcy&apos;s law using pressures measured during actual flow conditions. The ratio of the mobility in the oil region to the mobility in the inject ion-water region was approximately 0.32. The mobility ratio of the oil region to the connate-water bank was approximately 14. The mobility ratio between the connate-water bank and the injection water region was 0.024. Approximately 84.5 per cent of the recoverable oil was produced before water breakthrough. Immediately following breakthrough, oil and connate water were produced at an increasing water-oil ratio until the viscous injection water broke through. At viscous-water breakthrough, 96 per cent of the original connate water had been produced. After breakthrough of the viscous water, there was no additional production of connate water or oil. The near-

Jan 1, 1967

By A. M. Johnson, M. M. Singh

The mechanism of failure under a drill bit is still improperly understood in spite of several investigations of the subject. Generally, the cratering process under static loading conditions is considered to be similar to that achieved dynamically by impact. This paper attempts to indicate that, although the sequence of fracturing in the two cases appear to be identical, at least some dissimilarities exist. For example, the width-to-depth ratios of the craters vary to some extent, and the amount of energy consumed per unit of volume of craters is unequal for the two different loading conditions. Prevalent rock penetration processes are dominated by methods utilizing mechanical attack on rock. It is, therefore, generally accepted that a better comprehension of the mechanism of rock failure under a wedge would prove beneficial towards improving present drilling techniques. Several attempts have been made in recent years to explain how craters are formed under a drill bit, but the mechanism of failure beneath a bit is still improperly understood. 1-11 Most investigators, to date, have inferred the sequence of events occurring during crater formation from analyses of force-time diagrams,1"6 from theoretical considerations,7 or from a study of the configurations of final craters.8-l0 These analyses have led to the presentation of widely divergent models for rock failure beneath a drill bit, ranging from brittle to viscoelastic. The cratering process under dynamic loading commonly is regarded as being similar to that obtained under gradually applied, or &apos;static&apos;, loads. But the effect of rate of loading on the action of a bit is still disputed. Some investigators11-12 maintain that there should be no such effects, whereas others have demonstrated experimentally that these exist.13-17&apos; The purpose of the investigation reported in this paper was to examine petrographically the damage done to rock under the action of a chisel-shaped wedge, both with &apos;static&apos; and dynamic loading, and to determine if rate-of-loading effects could be detected. Significant quantitative differences in crater volumes and depths were found to exist for a given consumption of energy. On the basis of this data, an attempt was made to indicate some of the rheological properties that a proposed model should possess. All the work reported herein was conducted at atmospheric pressures. EXPERIMENTAL APPARATUS AND PROCEDURE Two types of rocks were employed for most of the experiments reported in this paper, viz. Bedford (Indiana) limestone and Vermont marble. The mechanical properties of these rocks are given in Appendix A. Actually two types of Vermont marble were used, but since no marked difference could be discerned between the two varieties (as seen in Fig. 10) the data was used collectively for the analysis. Stronger rocks were not employed owing to difficulty in generation of observable craters without damage to the equipment. Six-in. diam cores were drilled from the rock samples and embedded in 8-in, diam steel pipe with 3/8-in. wall thickness, using hydrostone to fill the annulus between the core and the pipe. This procedure was adopted to confine the rock specimen so that fractures would not propagate to the edges of the cores. This goal was achieved satisfactorily for these tests because no cracks were observed to extend into the medium surrounding the rock, even when craters were formed only 1 in. from the rock core periphery. Three to four craters were formed on a core face, because the rock damage from any one crater generally did not appear to extend into the others. Whenever, interference between damaged areas around adjacent craters was suspected, the data was rejected for purposes of the analysis. The limestone and marble samples were tested with a 60-degree, wedge-shaped bit, 1 5/8-in. in length, made of tool steel. The bit shank had two SR-4 type electrical resistance strain gages, mounted axially, to record the force-time history during the loading operation. The static indentation tests were conducted using a 50-ton capacity press fitted with an adapter for drill bit attachment. See Fig. 1. The force exerted by the bit at any instant was measured with strain gages affixed to the bit shank. An aluminum cantilever, with two SR-4 strain gages mounted near its clamped end, was employed to measure bit displacement. Both sets of gages were included in Wheatstone bridge circuits,

Jan 1, 1968

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

By R. W. Regehr, R. A. Burmeister

Epitaxial growth of GaAs 1-xPx on germanium substrates was achieved using an open tube vapor transport system. The compositional range of 0.3 < x < 0.4 was examined. The best results were obtained with (311) orientation of the germanium substrate. The physical and chemical properties of the resulting layers were investigated using several techniques. Spectrographic analyses of the layers indicate substantial incorporation of germanium into the GaAs t-X Px layer. Evidence is presented which indicates that this incorporation occurs via a vapor phase transport process rather than by solid phase dijfu-sion. Electrical measurements suggest that the germanium thus incorporated behaves predominantly as a deep donor in the compositional range of 0.33 < x * 0.40 and has a deleterious effect upon the luminescent properties of GaAs1-x Px. The increasing technological importance of GaAs1-xPx for use in light-emitting devices has led to an evaluation of several aspects of existing growth processes. The method most commonly used to prepare GaAs1-xPx for electroluminescent device applications is vapor phase epitaxial growth on GaAs substrates.&apos;-4 In a typical electroluminescent diode structure the active region of the diode is entirely within the epitaxial layer and thus the electrical properties of the substrate are relatively unimportant since it is effectively a simple series resistance (assuming hetero-junction effects to be negligible). The use of germanium rather than GaAs as the substrate material is of interest for several reasons. First, GaAs of reasonable structural quality has been epitaxially grown on germanium4-2 and it is reasonable to expect that GaAs1-xPx could subsequently be deposited on the GaAs layer. Second, germanium substrates are readily available with both lower dislocation densities and larger areas than GaAs. Finally, single crystals of germanium are more economical than GaAs single crystals. The principal objective of the present investigation was to test the feasibility of growing GaAs1-xPx epi-taxially on germanium substrates, and to evaluate the properties of such layers with regard to electroluminescent device requirements. The approach used was to a) demonstrate epitaxial growth of GaAs1-xPx on germanium, and b) characterize the relevant structural, electrical, and optical properties of the GaAs1-xPx layers. The possibility of germanium incorporation into the grown layers was of special interest since there was some indication of this in previous studies of GaAs growth on germanium.5&apos;11,12 Although a study of the electrical properties of germanium in GaAs1-xPx was not an intent of this investigation, several features of the electrical properties of the layers grown in the present study which appear to be due to germanium are described. EXPERIMENTAL PROCEDURE The open-tube vapor transport system used for the epitaxial growth of GaAs1-xPx is illustrated in Fig. 1. This system utilizes the GaC1-GaC13 transport reaction and is similar in most respects to the larger system described elsewhere.&apos; The germanium substrates were n-type, with a resistivity of 40 ohm-cm (Eagle-Picher Co.). These were cut to the orientations of {100), {111), and (3111, and were mechanically polished and chemically etched in CP-4 (5 min at 0°C) prior to growth. In some cases, a GaAs substrate was employed in addition to the germanium. The orientation of the latter was {loo}, and they were also mechanically polished and chemically etched prior to growth. The initial composition of the deposited layer was pure GaAs. After approximately 10 microns of GaAs was deposited on the germanium substrate, the phosphorus content of the layer was gradually increased over a distance of approximately 15 microns to the desired concentration and maintained at this value throughout the remainder of the growth. Typical operating parameters used during growth are given in Table I. Selenium was used as a n-type dopant in several runs to facilitate comparison of the electrical properties of the layers grown on germanium with those of layers grown on GaAs substrates, which are usually doped with selenium. The concentration of H2Se in the gas phase was adjusted to a value which would normally yield a carrier density of 1 to 5 x 101 7 at room temperature in layers grown on GaAs substrates. The terminal surfaces of the epitaxial layers were examined by optical microscopy for structural characteristics. Laue back-reflection photographs (Cu radi-ation) were also made on the terminal surface to verify the epitaxial nature of the deposit. After these steps

Jan 1, 1970