Search Documents

By E. T. Turkdogan, P. Grieveson

Molten silver is equilibrated with silicon nitride at 1400°C in nitrogen + hydrogen gas mixtures, and from the solubility data the activity coefficient of silicon is found to be 1.76 at silicon concentrations below 1 pct. Using this value, and that available from the silicon cmbide solubility measurements, together with those derived from the phase equilibrium diagvam, the activities of silver and silicon are estimated for the entire composition range. The main feature of the activity data is that there is a pronounced positive deviation from ideality. The activity of silver in molten silver containing up to 5 pct Si was determined by Schadel, Derge, and Birchenall1 by measuring the vapor pressure of pure silver and of the alloy over a temperature range of 850º to 1050°C. They deduced from their results that there is a positive deviation from Raoult's law and that the activity coefficient of silver increases with decreasing temperature. However, as pointed out by Kubaschewski and Catterall,2 their activity coefficients are much too high, giving silver activities greater than unity. At a later date McCabe and Birchenal13 showed that the previous vapor pressure data on silver4 were high by a factor of about 1.3; presumably a similar error must have occurred with the vapor pressure measurements on the Ag-Si alloys. The activities of silicon and silver calculated by tager' from the phase diagram and by Gibbs-Duhem integration, respectively, show a positive deviation from Raoult's law for silicon activity and positive and negative deviations for the silver activity. According to these computations, at infinite dilution of silicon ygi = 1.12 at 1420°C. d'Entremont and chipman6 measured the solubility of silicon carbide in molten silver at unit carbon activity; the equilibrium silicon content is found to be Nsi = 0.017 ± 0.002 atom fraction for 1420°C. Using the data of Grieveson and Alcock7 for the free energy of formation of silicon carbide from pure silicon and graphite, the activity of silicon for unit activity of carbon and of silicon carbide is asi = 0.0308 at 1420°c; therefore for the above solubility data on silver, YSi = 1.81, which is somewhat higher than that given by Hager. Use is often made of silver alloys in the measurements of activities of solutes in metals where silver has a very low solubility; in fact, Ag-Si and Ag-A1 alloys have been used in the past for such purposes. In an attempt to gain more thermodynamic data on molten Ag-Si alloys, measurements have been made in the present study on the solubility of silicon nitride in molten silver; the results on these solubilities are given in this paper together with a detailed discussion of activities of silver and silicon. SOLUBILITY OF SILICON NITRIDE The standard free energy of formation of silicon nitride is known with a reasonably high degree of accuracy. According to the measurements made by Hincke and Brantle8 and by Pehlke and Elliott,' the following are the free energy data for the standard states of solid Si3N4, liquid silicon, and Nz at 1 atm pressure:

Jan 1, 1963

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-In phase diagram has been determined by thevmal, filtvation, micrographic, and X-ray diffraction methods. This alloy system is characterized by 1) limited solubility of indium (-2 at. pet) in 6 and e plutonium, 2) one eutectic, and 3) fizte intermediate phases. Of the latter, PuIn and PuIn3 melt con-gruently, and Pu31n, Pu31n5, and the high-temperatuve 7 solid solution are formed peritectically. The n phase decomposes eutectoidally into Pu3In and PuIn at 865°C. Although the 6 phase can readily be retained to room temperature, it is not thermo-dynamically stable below 300°C. The Pu-In system has been investigated at Los Alamos as part of a study of the alloys of plutonium with the group 111-B elements. Constitutional studies of the Pu-A1 and Pu-Ga systems have been reported earlier.&apos;9&apos; To date, published information on the constitution of Pu-In alloys covers only the identification of the intermediate phases Pu3In and PuIn3.3,4 EXPERIMENTAL The alloys were prepared from five different lots of plutonium and three different lots of indium. The principal impurities in the plutonium differed from lot to lot within the following limits (in ppm): iron, 30 to 80; nickel, 30 to 60; aluminum, 15 to 30; silicon, 20 to 145: thorium, 50 to 300; carbon, 75 to 335; and oxygen, 20 to 135. Spectroanalysis of the indium showed that two of the lots were 99.9 wt pct pure, and the third was 99.98 wt pct pure. The alloys, in the form of about 5-g buttons, were prepared by arc melting in conventional equipment. The components for each alloy were weighed to the nearest 0.1 mg. In most instances the weight losses during melting were negligible; therefore confirmatory chemical analyses were usually not made. A few results are given in Table I. Density measurements of the arc-cast buttons were made by the liquid displacement of bromoben-zene. Heat treating was done in muffle furnaces controlled to +2°C. The alloy buttons were wrapped in tantalum foil before being enclosed in evacuated clear silica capsules. As a precaution against breakage, each capsule was in turn placed in a silica tube closed with a refractory wool plug prior to being charged into the furnace. For a moderately fast quench of the alloys, the outer protection tubes containing the capsules were plunged into cold water. Differential thermal analyses (DTA) in racuo were performed at heating and cooling rates of about 1.5°C per min. Tantalum crucibles having inverted thermocouple wells were used for most of the analyses. It was found micrographically, however, that the liquid alloys containing more than about 35 at. pct In reacted with the tantalum, resulting in contamination of the surface of the alloy. A search for a more satisfactory crucible material was not successful: tungsten and yttria behaved comparably to tantalum; thoria, vitrified magnesia, and vitrified alumina severely contaminated the alloys. So as to minimize the contamination by the crucible mater-

Jan 1, 1965

By W. M. Phillips

Processing kaolin clays from the sedimentary deposits of Georgia and South Carolina is described in this article. While the major processing steps are touched on briefly, emphasis is given to the dewater-ing of the clay-water slurries (slips) formed in the processing of kaolin clays. The dewatering steps discussed include gravity settling, centrifugal dewatering, vacuum filtration and thermal drying. Particular attention is given to vacuum filtration and the variables affecting filtration of these kaolin clays. Kaolin consists essentially of the mineral kaolinite, which is a hydrated aluminum silicate (Al2O3 . 2SiO,). Commercial deposits of kaolin occur in several areas of the U. S., but approximately 90% of the kaolin produced in this country comes from Georgia and South Carolina. These deposits are of sedimentary nature and occur in a geological fall line in the Tuscaloosa formation at elevations between 300 and 450 ft above sea level. Over two million tons of kaolin clays are used by industry in the U. S. each year. A big percentage of this tonnage is used in the paper industry for coatings in making glossy and high quality grades of printing papers. In addition, large tonnages are used as pigments; as fillers for rubber, plastic and fertilizers; and in ceramics. Properties of kaolin that make it widely used in the above applications are its particle size fineness, natural whiteness, chemical stability and non-abrasiveness. In addition to these desirable properties, it is relatively inexpensive. The finer coating grades of clays range in price from $15 to $28 per ton while the coarser filler grades sell within a range of $7 to $13.50 per ton. Pure kaolin particles are small hexagonal flat platelets. Above the 2-p size, the particles usually consist of stacks of plates, while below the 2-p particle size they occur as individual flat, hexagonal plates. Since these individual platelet particles provide the most desirable coating and flow characteristics, major importance is given to particle size fractions of 2 p and smaller. Generally, coating grade clays are those with all particles smaller than 15 p and at least 70% of the particles less than 2p. These coating grades also have 50% or more of the particles smaller than 1 µ in size. The extremely fine grades of coating clay currently being produced approach the range of 100% smaller than 2p. The filler grades of kaolin have 100% of the particles passing 325 mesh but have less than 70% of their particles below the 2-p range. Fig. 1 is a schematic representation of the major processing steps involved in preparing kaolin clays for marketing. MINING All kaolin mining is open pit. The ratio of overburden to clay will average 3:1, but this ratio can, of course, be much higher depending upon the grade of the clay and the size of the deposit. Most of the commercially mineable deposits occur from 20 to 120 ft below the ground surface. Both draglines and pans are used in removing the overburden and mining the clay deposit itself. After mining, the most common method of transporting the clay to the processing plant is by blunging or re pulp-

Jan 1, 1963

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

By D. H. Gieskieng

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely Werent materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected capacity data. Recording instruments are connected to crushers in such a manner that a continuous record is produced which discloses the inherent maximum capacity of the crusher and shows capacity decreases caused by hangups. The capacity effects of various crushing conditions are made more evident by this arrangement. The recording instruments were first applied to a standard sized 10 by 7 in. Blake-type jaw crusher in the laboratory. Suficient tests were run on this with various combinations of setting, throw, speed, feed sizing, shapes of jaw plates, and other operating features, to establish the individual effect of each on the capacity. The instruments later were applied to much larger crushers in the field, through the excellent cooperation of the managements in the Mesabi Iron Range, and data were obtained which closely corroborated the established trends. The capacity equation resulting from the test work is made up of a series of factors, each representing the contributing effects of setting, speed, width of chamber, nip angle, feed density, type of jaw plates, stroke, and the overall operating technique. Fortunately, most of these factors were revealed to be in direct proportion to the capacity for straight plate chambers. This equation is also applicable to chambers using curved plates, with slight modifications resulting from the capacity limitation of the upper portion of the crushing chamber. The equation has been derived from tests covering a very wide range of feed density and hardness. It has been found valid, providing that the feed material is either nonpacking in character, as is usual, or allowance in designing the crushing chamber shape has been made to accommodate this characteristic. Preliminary investigation has shown that the equation is also applicable to single-toggle jaw crushers. Conditions of this are that the top of the flywheel rotate towards the top of the crusher opening, and that the horizontal motion of the swing jaw relative to the stationary jaw at the discharge opening be considered as the stroke. The relatively large upper chamber jaw motion would probably result in realiza-

Jan 1, 1950

By W. Rostoker, D. W. Levinson, A. Yamamoto

The influence of carbon on tensile strength, tensile ductility, transformation kinetics, and grain growth characteristics of selected Ti-Mo base alloys was studied. No systematic influence of carbon in tensile strength or significant deleterious effect on tensile ductility was observed. There was a marked increase in transformation rate due to carbon. Dispersed carbides exert a marked inhibiting effect on grain boundary migration, and thus effectively prevent grain coarsening during solution treatment in the ß phase field. AS part of a research program directed toward the illumination of factors governing modes of transformation, transformation kinetics, and mechanical properties obtainable through these transformations by heat treatment, Ti-Mo base alloys were selected for study. The binary system is a characteristic phase diagram type which has been studied in some detail&apos;, &apos; in relation to transformation kinetics and mechanical properties. Although carbon bearing alloys have acquired a bad reputation, the possibilities of melting titanium under conditions which occasion some carbon pickup are very attractive. It is therefore of considerable importance to know whether carbon, present as a dispersed carbide phase, is actually deleterious when all other detrimental factors are minimized. Basic alloy compositions containing nominally 3, 5, 7, and 11 pet Mo were prepared with systematic carbon addition up to 1 pet by weight. Various of these alloys were subjected to a series of critical and definitive experiments to delineate the effect of carbon on the transformation behavior and associated mechanical properties. Experimental Procedure Alloys were prepared from 115 Bhn magnesium-reduced sponge titanium. This sponge analyzed ap- proximately 0.05 pet C. Ti-Mo and Ti-C master alloys were made by arc-melting the sponge with high purity (99.9 + pet) molybdenum and spectro-scopic grade graphite, respectively. Alloys were then prepared from the master alloys and sponge by double are-melting. One kg ingots were prepared by melting in a nonconsumable electrode furnace. These ingots were forged at 1000°C to &apos;/z in. rods, and cleaned and processed into electrodes for the second melting operation. The final ingots were ground to remove surface defects, then forged again to 1/2 in. or 3/8 in. diam rods for processing to test samples. It is significant that all of the alloys at all carbon levels forged satisfactorily. For convenience, the alloys will be referred to throughout the text by their nominal analyses. Samples for the study of transformation rates were prepared from 1/2 in. diam round stock. They were then solution treated in a helium filled tube furnace at 1000°C for 30 min prior to the isothermal transformation treatments in lead bath furnaces. Temperature control in both cases was within ±3oC. Following the isothermal transformation treatments the samples were water quenched. These experiments were carried out before the general adoption of the resistometric procedure for kinetic studies. The data were therefore obtained entirely by metal-lographic analysis. M, temperature was also determined by the metallographic method. Shoulder-type tensile test pieces were machined from heat treated, 1/2 in. diam slugs to provide a 0.252 in. test diam and a 1 in. gage length. The isothermal-type heat treatments were chosen from previous data&apos; to provide three levels of strength and ductility.

Jan 1, 1957

By M. C. Flemings, P. J. Ahearn

Dendvite morphology of unidirectionally solidified Sn-12 pct Bi alloy was determined with the aid of X-ray and macroetch techniques. Columnar growth direction (growth direction of primary arms) in this alloy is [110]; secondary arms grow in the [lii], [111), and [112] directions. Interstices between [112] dendrite arms fill in during early stages of solidification so that well-defined (110) planes are seen in the final structure (parallel to the heat-flozo direction). Similarly, interslices betweex the [111] secondary arrlls fill in to form (112) planes, and interstices between [1111 ] arms fill in to form (112) planes. DENDRITE morphology in alloys is conveniently studied in unidirectionally solidified castings. In this type of solidification, heat is extracted from a single chill surface of the casting while other surfaces are insulated. Solidification progresses from the chill and results in cast grains that are columnar with the long axis of the grain perpendicular to the chill. Dendrite morphology is conveniently studied by examination of etched surfaces parallel and perpendicular to the chill, as previously described.&apos;" Experimental studies on the growth direction for tin are in general agreement. The major growth direction is [110]:-&apos; although this is altered somewhat by supercooling. In one study, tin dendrites pulled from a supercooled melt had a growth orientation 12 deg away from the [110] direction toward the [002] direction.&apos; This orientation could be changed back to the [110] or close to the [110] direction by changing the tempera- ture gradient in the melt. In a study using autoradio-graphic techniques, (111) directions were shown to be directions of preferred growth in addition to the [110) direction.7 PROCEDURE The samples employed in this study were cut from 12 pct Bi-88 pct Sn castings, 1.5 in. in diam and 3.5 in. tall. The casting procedure consisted of heating the charge to 390°C and then pouring the molten alloy directly into a gypsum sleeve mounted on a massive copper chill. Specimens were cut from the ingot, mounted, polished, and etched with Taffs reagent [FeC13 .6H2O, 2 g; HC1, 5 cu cm;H20, 30 cu cm; CzHaOH (95 pct), 60 cu cm].&apos; The dendritic pattern was clearly visible after etching. Photomicrographs at about 8 and 35 times were taken on surfaces parallel and perpendicular to the chill. Laue back-reflection patterns were obtained from three different columnar grains in a singIe polished face 2 in. from the chill. The cut face was polished and positioned in the beam of a Laue camera, so that diffraction occurred from a single dendritic grain. The resulting diffraction pattern was interpreted to determine crystal log raphic orientation in relation to the heat-flow direction and in relation to microstruc-ture of the given grain. RESULTS Fig. 1 shows a horizontal and vertical section of the columnar structure, at low magnification. Light regions are rich in tin, and darker regions tin-poor; the primary phase is tin-rich a phase. The two sections shown were taken orthogonally from the same metallographic specimen. It is readily seen from Fig. 1 that the dendrites have

Jan 1, 1968

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12&apos;3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By Lauren A. Wright

SINCE the early nineteen-thirties the production of talc* in California has increased five-fold to a yield in 1947 of about 76,000 tons (fig. 1); conse- .&apos; Unless otherwise qualified, the term "talc" in this paper will imply a mixture of the pure talc with such related minerals as commonly occur in the commercial material. quently the state is now one of the nation&apos;s three principal talc producers. The 1947 output, which represented about one-sixth of the national total for that year, was approximately equal to production from Vermont, and was second in value to that from New York. New York has an annual output of about 130,000 tons. Three factors have been mainly responsible for the expansion of talc production in California. (1) Technical advances and innovations, particularly in the ceramic industry, have increased the demand for certain California talcs. The nation&apos;s high-qual- LAUREN A. WRIGHT, Junior Member AIME, is Associate Geologist, California Division of Mines, San Francisco, Calif. Los Angeles Meeting, October 1948. San Francisco Meeting, February 1949. TP 2622 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscripts received Dec. 7, 1948; revision received Aug. 29, 1949. This paper is Contribution No. 508 of the Division of Geological Sciences, California Institute of Technology, Pasadena, Calif. the industry, mainly through demand for the urgently needed steatite. Fibrous talc, used as a paint extender by the armed forces, also was produced in quantity. (3) Expanding western industry has continued to draw heavily on California talc deposits, and has extended the upward production trend into the postwar period. Considerably more than half of California&apos;s current talc output is used as ceramic raw material. The paint, rubber, paper, and textile industries are the more important consumers of the remainder. Smaller amounts are used as insecticide carriers, and in cosmetics, and various minor industrial applications. During World War I1 the principal steatite deposits were studied in detail by members of the U. S. Geological Survey; other sources of commercial talc in the state have in the past received but scant geologic attention. The following discussion is essentially a preliminary report based on research currently in progress by the California Division of Mines, and includes a brief outline of previous steatite studies by the U. S. Geological Survey. Distribution of California Talc Deposits: The principal talc resources of both California and Nevada are confined to an elongate belt that extends from the vicinity of Baker, in north-central San Bernardino County, northwestward to include the southern Death Valley region, the Inyo Range, and the Palmetto-Oasis district of western Nevada (fig. 2). This belt, of which all but the northernmost tip lies in California, is approximately 200 miles long and 30 miles in average width. Included in the belt are four contrasting areas. The deposits within each area are geologically similar and yield talcs that have characteristic properties and applications. Three of these local "talc provinces" lie within California&apos;s portion of the talc-

Jan 1, 1951

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state&apos;s conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company&apos;s gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state&apos;s conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company&apos;s gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By J. T. McGrath, G. B. Craig

Tensile tests on aluminum single crystals, grown from the melt, revealed that the yield stress of these crystals was raised as the amount of striation substructure was increased. The number of striation-type boundaries was varied by changing the rate of growth of the crystals. The results are interpreted in terns of a blockage of dislocation movement by striation boundaries. IMPERFECTIONS are known to have a large effect on the mechanical properties of metals. Teghtsoonian and Chalmers 1 studied a block or striation-type substructure in tin and found that the formation of the striations depended upon rate of crystal growth and orientation. They found that the angular misorienta-tion between neighboring striations varied between 15 min and 5 deg. Atwater and chalmers2 investigated striations in tin and lead, and found that purity was another factor which influenced their formation. There was a limiting purity above which the striations were straight and regular. There is little information in the literature concerning how substructures in melt-grown crystals affect strength. washburn3 introduced small-angle boundaries into zinc by a shear process and found a subsequent increase in yield stress which he attributed to the presence of these boundaries. Lauriente and pond4 found the critical resolved shear stress in aluminium crystals grown from the melt, to increase with etch pit density. The etch pits were used as an indication of growth imperfections. In Hibbard&apos;s5 work on lineage structure in copper crystals grown from the melt, he tested one crystal containing interlineage boundaries, and found a 50 pct increase in the critical resolved shear stress. Fleischer and Chalmers6, in a recent paper, mention briefly that, in the production of aluminium crystals from the melt when the growth rate was raised from 1.2 to 18 cm per hr, the yield stress increased 50 pct. They felt that the increase in yield stress with rate of growth might be attributed to a higher concentration of impurities in the gage length and also might be affected by the increased number of small-angle boundaries (striations). The present investigation was undertaken to determine the effect of the striation substructure on the strength of aluminum single crystals. EXPERIMENTAL PROCEDURE Aluminum single crystals of 99.9992 purity were grown from the melt using a technique described by Chalmers.7 The growth rate was varied from 0.6 to 20 mm per min, thus producing crystals with varying numbers of striation boundaries. To avoid prior deformation, the crystals were chemically cut to the desired length with a saturated solution of cupric chloride. They were then annealed at 580°C for 24 hr and allowed to cool slowly in the furnace. Finally, the specimens were electropolished using an electrolyte of 5 parts ethyl alcohol and 1 part perchloric acid. Each specimen was approximately 5 in. in length and 0.125 sq in. in cross section. The average orientations of the 5 series of crystals studied are shown on the stereographic projection of Fig. 1. The crystals were strained approximately 2 pct in a soft tensile machine. The strain sensitivity was 3.6 x 10-4 cm over a 5-cm gage length.

Jan 1, 1960

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By C. W. Spencer, Che-Yu Li, R. J. Knight

The usual reaction product for the monotectic reaction in the Bi-Se system consists of rod -shaped particles of selenium-rich liquid embedded in a single crystal matrix of At certain crystallo-graphic orientations of the matrix with respect to the reaction interface, more complex shapes are as -sumed by the liquid particles. This reaction has been examined at different growth rates and relative crystallographic orientations of the matrix with respect to the reaction interface. The uhriation in auerage particle size of the liquid phase with reaction rate has been determined at one crystallograpIzic orientation of the matrix. On a plot of logarithm of average particle diameter vs logarithm of reaction rate, data points for crystals grown at rates of 10- to 1.0 cm per hr fall near a curve of slobe -0.4. MONOTECTIC reactions in binary alloy systems are reactions of the eutectic class in which, as the system is cooled through the three-phase reaction isotherm, one liquid phase (L) decomposes to a solid phase and another liquid phase (LII).&apos; A partial phase diagram, as taken from Hansen, showing the monotectic reaction in the Bi-Se system is given in Fig. 1. This diagram specifies the monotectic point at 618°C and 72 at. pct Se, and the monotectic reaction products as the intermetallic Bi Se3 and a liquid (LII) which contains approximately 98 at. pct Se. At a lower temperature, 217°C, this liquid may undergo a eutectic reaction in which the reaction products are BizSe3 and crystalline selenium. However, under conditions of rapid cooling, or quenching, from above 217°C, this selenium-rich liquid may be partially retained to room temperature in an amorphous or glassy state. The intermetallic BizSe3 is rhombohedral, of the space group jm;&apos; however, for convenience it is usually represented by a hexagonal struture. A pronounced plane of cleavage, which lies perpendicular to the main axis of the rhombohedral unit cell or parallel to the basal plane of the hexagonal cell, exists in the structure. The usual monotectic reaction product consists of rod-like particles of LII embedded in a single-crystal matrix of BizSe3, although at certain crystallographic orientations of the matrix BizSe3 other more complex shapes are assumed by LII. A similar rod-like, or cylindrical, morphology for the carbide phase has been reported by westbrook7 in the a Cr-Crz3Ce eutectic structure. In this paper the morphological characteristics of the LII particles, as retained to room temperature, have been examined under conditions of varying growth rate and crystallographic orientation of the matrix BizSe3 with respect to the growth direction. EXPERIMENTAL PROCEDURE Alloy specimens corresponding to the monotectic composition, 72 at. pct, or 50 w pct Se, were prepared from 99.999 pct pure bismuth and selenium obtained from the American Smelting and Refining Co. The two elements, corresponding to a total specimen weight of approximately 30 g, were encapsulated in 13 mm OD Vycor tubing under a vacuum of 5 x X mm of Hg. The capsules were suspended on a fine platinum wire in a Bridgman-type furnace which exhibited a temperature gradient of

Jan 1, 1963