Search Documents

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By J. C. HEILMAN

THE Tri-State district, named from its situation in three States, lies in the northeast corner of Oklahoma, the southeast corner of Kansas and the adjacent part of Missouri east of the common corner of the above States. Production in the past eighty years has come from scattered mines within an area of some 35 miles east and west, by 25 miles north and south, although the actual area of the mined ground is but a small fraction of this territory. The land is leased from the individual land-owners, and the size of the tracts varies from 4.0 to 200 acres, the smaller sized tracts predominating. The leases usually call for a royalty of 7% to 15 per cent of the gross receipts of the concentrates, continuous operation during the life of the lease and specifically set out that no ores can be brought in from a foreign lease for custom milling nor can any ore be removed from the lease for milling. The ownership of the tailings remains with the land-owner.

Jan 1, 1931

By F. Louis Grammer

The difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace ga,s is higher in CO2 and lower in hydrocprbons and hydrogen, as is shown in Table I. Table I.— Volume-Composition of Producer-Gas and Blast-Furnace Gas. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO......22 to 33 25.5 CO2........ 6 to 3 13.0 H...13 to 7 1.5 CH4........ 3 to 1.5 0.0 N..54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydrocarbons and hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur—namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the mine-products which are specially high in sulphur-content. An advantage would be gained if the coal were coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Jan 1, 1909

By E. D. Gardner

IN 1947 the metal-mining industry . passed through a year of readjustment; catching up on development work has caused production to suffer. Skilled labor has been short in most mining districts, notwithstanding the highest wage rate paid in the history of the industry. The trend has continued toward increased mechanization and refinements in practices and methods to increase the tons produced per man-shift. Improvements in procedures, however, have not kept pace with rising labor rates; and, in general, labor costs per ton mined have steadily increased since the war years. Prices of base metals have been the highest in a generation, but most producing companies can afford to pay the high wages. Capital expenditures have been approved for improvements to increase the output per man, both to reduce unit labor costs and to increase output. Surveys indicate a continuing

Jan 1, 1948

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By P. R. Bradley

NO thought had been given to deep level mining at the Alaska Juneau mine prior to 1930, but in that year a prospect winze was started and continued for 1000 ft. vertically below the main haulage or adit level. The point at which this winze was started was selected entirely by the prevailing physical conditions, such as proximity to established workings, convenience, and the presence overhead of a substantial pillar of dimensions sufficient to lo¬cate the sheave wheel and loading pocket. It was, therefore, with some surprise that the unusually high-grade ore found just below the collar of the winze persisted, with certain vari¬ations, to a full depth of 1000 ft. vertically. Likewise this unusually high-grade ore was found to persist on the various crosscuts driven on levels at 200-ft. vertical intervals. To be brief, this deep level work found richer ore than any yet found in the mine over like areas, and inasmuch as the area was sufficient to plan for extensive deep level mining, plans for such work were given extended consideration.

Jan 1, 1936

Harry HaRkness Stoek, whose sudden death on March 1,1923, was a great shock to his friends in all park of the country, was a man of remarkable personal characteristics and mental ability. Through an acquaintance with him of nearly 35 years, during 12 yeam of which I was intimately associated with him both in business and socially, I learned to appreciate his many high qualities, his strict adherence to high professional and social ideals, and his lovable traits of character. In this appreciation I was joined by every one who was thrown in close personal contact with him. He was a conscientious student, not given to hasty judgments, but when he formed an opinion he was positive in upholding it. At the same time, he was most courteous and kindly in combatting that which he believed was erroneous. In fact, I never knew a person of his attainments more modest, forceful and kindly, or one who had a keener sense of clean humor. In his private life,he was a devoted husband and father, a consistent communicant and worker in the Episcopal Church, and was charitable in all things. In fact, his whole life was marked by helpfulness to others and a determined and successful effort to "make the world better by his having lived in it." Doctor Stoek was born in Washington, D. C., Jan. 16, 1866. His early education was obtained in the public schools of that city and he graduated from the Central High School in the first class to graduate from a high school in Washington. He entered Lehigh University in 1883, graduated in 1887 with the degree of Bachelor of Science, and after a year of post-graduate study in mining and metallurgy he received the degree of Engineer of Mines. During the summer vacation in 1885, he served as an assistant in the Department of Mineralogy in the National Museum at Washington, and during the summer of 1887 acted as U. S. Government inspector of dredging on the Tharnes River, Connecticut. From June, 1888, to January, 1900, he was assistant engineer for the Susquehanna Coal Co., at Wilkes-Barre, Pa. From January, 1890, to June, 1893, he was Instructor in Mining, Metallurgy and Geology at Lehigh University, and had charge of all courses in mining and metdlurgical design, and the visits of students to mines and metallurgical

Jan 1, 1923

Harry HaRkness Stoek, whose sudden death on March 1,1923, was a great shock to his friends in all park of the country, was a man of remarkable personal characteristics and mental ability. Through an acquaintance with him of nearly 35 years, during 12 yeam of which I was intimately associated with him both in business and socially, I learned to appreciate his many high qualities, his strict adherence to high professional and social ideals, and his lovable traits of character. In this appreciation I was joined by every one who was thrown in close personal contact with him. He was a conscientious student, not given to hasty judgments, but when he formed an opinion he was positive in upholding it. At the same time, he was most courteous and kindly in combatting that which he believed was erroneous. In fact, I never knew a person of his attainments more modest, forceful and kindly, or one who had a keener sense of clean humor. In his private life,he was a devoted husband and father, a consistent communicant and worker in the Episcopal Church, and was charitable in all things. In fact, his whole life was marked by helpfulness to others and a determined and successful effort to "make the world better by his having lived in it." Doctor Stoek was born in Washington, D. C., Jan. 16, 1866. His early education was obtained in the public schools of that city and he graduated from the Central High School in the first class to graduate from a high school in Washington. He entered Lehigh University in 1883, graduated in 1887 with the degree of Bachelor of Science, and after a year of post-graduate study in mining and metallurgy he received the degree of Engineer of Mines. During the summer vacation in 1885, he served as an assistant in the Department of Mineralogy in the National Museum at Washington, and during the summer of 1887 acted as U. S. Government inspector of dredging on the Tharnes River, Connecticut. From June, 1888, to January, 1900, he was assistant engineer for the Susquehanna Coal Co., at Wilkes-Barre, Pa. From January, 1890, to June, 1893, he was Instructor in Mining, Metallurgy and Geology at Lehigh University, and had charge of all courses in mining and metdlurgical design, and the visits of students to mines and metallurgical

Jan 1, 1923

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By H. N. Lawrie

Introduction. THIS study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility-two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten ' and Levol,2 using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleabilitytests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi2O3, on the copper protoxide, CuO. Hampe's conclusions of the influences of these two latter compounds of bismuth on copper are as follows "If the protoxide of bismuth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Sep 1, 1909

Jan 1, 1966

By James Bowron

CONSIDERING the importance of the steel trade and the strategic position occupied in it by the Birmingham District, it may be surprising to many to realize that even the first pig iron smelted with coke was made in Alabama on Feb. 28, 1876, although merchant pig iron had been produced in Rockwood, Tenn., in 1867, a plant which is still in active operation. The heavy deposit of Clinton ore extending from Pennsylvania into Alabama, varying greatly in accessibility on account of geological changes such as erosion or anticlinal upthrow, varies equally as much in thickness and in quality. The brown ores extensively scattered through the South also vary materially in quality, some being relatively low in phosphorus and high in manganese, and vice versa. The red ore varies materially in phosphorus, but the iron produced from these ores was always considered to be too high in phosphorus for treatment by acid Bessemer or open hearth and did not contain sufficient for the basic Bessemer process. Under these conditions there remained only the basic open hearth as a possibility, and for many years it appeared impossible to use it, because, with coke smelted iron, the silicon was too high to permit its use in basic lined furnaces.

Jan 1, 1924

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By H. R. Wheeler

CREATION of a "committee on promotion of student interest in coal mining" has an encouraging implication for the coal industry. It is indicative that mining men, both in the field and in the educational centers, realize that the problems of the industry require the best talent available. Young men are being invited into coal on the premise that it needs them, that it offers opportunity for creative work and the realization of their objectives. In initiating a movement which purports to meet the objectives of any young man who spends four or five years of his life in college, the industry does so with a full realization of its obligations.

Jan 1, 1940

By R. S. Wagner, W. C. Ellis

A new mechanism of crystal growth involving oapor, liquid, crnd solid phases explains many observations of the effect of implurities in crystal growth from the vapor. The role of the impuuitq is to form a liquid Solution with the crystalline tnalerial to be grown from the vapor. Since the solution is n prefevred site for deposition firorti the uapor, the liquid becorrles supersaturated. Crystal growth occurs by precipitatzon from the supersaturated liquid crt tlie solid-liquid zntevfnce. A crystalline defect, such as a screw dislocation, is not essetztial for VLS (vapor -liquid-solid) growth. The concept of the VLS mechanism is discussed in detail with reference to tire controlled growth of silicon crystals using gold, platinum, palladium, nickel, silver, or copper as an implurity agent. RECENTLY a short communication' described a new concept of crystal growth from the vapor, the VLS mechanism. In this paper we present a detailed description of the process and its application to the growth of silicon crystals and we discuss its relevance to existing concepts of .'whisker" crystal growth. Crystal growth from the vapor is usually explained by a theory proposed by Frank2 and developed in detail by Burton, Cabrera, and Frank.3 In this theory a screw dislocation terminating at the growth surface provides a self-perpetuating step. Accommodation of atoms at the step is energetically favorable, and is possible of much lower supersatu-ration than required for two-dimensional nucleation. Crystals of a unique form resulting from aniso-tropic growth from the vapor are "whisker" or filamentary ones. Such crystals have a lengthwise dimension orders of magnitude larger than those of the cross section. For most filamentary crystals both the fast-growth direction and directions of lateral growth have small Miller indices. The special growth form for a whisker crystal implies that the tip surface of the crystal must be a preferred growth site. sears4 proposed that, according to the Frank theory. a whisker contains a screw dislocation emergent at the growing tip. Such an axial defect provides a preferred growth site and accounts for unidirectional growth. The hypothesis was extended by Price. Vermilyea. and Webb," still implying the presence of a dislocation at the whisker tip. They postulated that impurities arriving at the fast-growing tip face become buried while those arriving on the surface of slow-growing lateral faces accumulate and thereby hinder growth. These considerations led to a whisker morphology. There is increasing evidence that most whisker crystals grown from the vapor are dislocation-free. Webb and his coworkers6 searched for an Eshelby twist7 in zinc? cadmium, iron. copper, silver, and palladium whisker crystals. They found unequivocal evidence for an axial screw dislocation in only one element, palladium. However, not every palladium crystal examined contained a dislocation. Observations with the electron microscope have failed to show dislocations in whisker crystals of zinc, silicon.9 and one morphology of AlN.10 Since many whiskers are completely free of dislocations, an axial dislocation does not appear to be required for whisker growth of many substances. A significant advance in understanding whisker growth has been a recognition of the need for impurities. This requirement has been clearly demonstrated for copper,11 iron,13 and silicon9-1 whiskers. For silicon, detailed studies proved conclusively that certain impurities, for example, nickel or gold, are essential. Another pertinent phenomenon which has received little attention is the presence of a liquid layer or droplets on the surface of some crystals growing from the vapor. Crystals in which this has been observed include p-toluidine,14 MoO3,15 ferrites,16 and silicon carbide.'" The liquid layers or globules were considered to be metastable phases, molecular complexes, or intermediate polymers originating from condensation of the vapor phase. The possibility has been suggested that the halide being reduced is condensed at the tip18 or adsorbed on the surface11 of a growing metal whisker, for example copper. The literature on whiskers discloses illustrations of rounded terminations at the tips. These appear. for example, on crystals of A12O3,19,20 sic,21 and BeO.22 For BeO, Edwards and Happel suggested that during growth of the whisker the rounded termination consisted of molten beryllium enclosed in a solid shell of BeO. A recent paper9 on the growth of silicon whiskers contains many observations pertinent to an understanding of the mechanisnl of whisker growth. These observations are summarized as follows. 1) Silicon whiskers are dislocation-free. 2) Certain impurities are essential for whisker growth. Without such impurities the silicon deposit is in the form of a film or consists of discrete polyhedral crystals.

Jan 1, 1965

By R. V. Norris

1. INTRODUCTION. THE anthracite coal trade, with a shipment averaging about 70,000,000 tons per year, differs essentially from other coal business, in the fact that the larger sizes, comprising about 65 per cent. of the total, are used almost exclusively for domestic purposes, principally during the winter months; and that for proper combustion close-sizing is imperative, so that eight sizes are made; broken, egg, stove, and nut, known as prepared sizes, and pea, buckwheat, rice, and barley, known as steam sizes. These sizes are made in the regular course of preparation, and but little variation in the natural percentage of each is practicable. Thus it is necessary either to work the collieries intermittently, or to dispose of all the varying sizes in their fixed proportions. Unfortunately, the market does not at all times absorb the coal in proper proportions, and rather than interfere with the regular operation of the mines it has been found economical to provide storage for the excess. While the cellars of the consumers are the great storage-plants of the country, this capacity is not under the control of the trade, except so far as reduced prices during the spring and summer months may tempt the use of this reserve. The same remark applies but with less force to the retail yards, which,, though usually small, store in the aggregate a large amount of anthracite. While every effort is made to utilize to the utmost the individual storage-capacity of the country, there still remains the necessity for taking care of the irregularities of the market by the construction of storage-plants under the direct control of the producers. Such plants are usually the property of the railroads, and are situated at points most convenient from a traffic stand-point.

Jun 1, 1911

Jan 1, 1897