Search Documents

By Earnshaw Cook, H. S. Avery, J. A. Fellows

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By E. S. Fisher, L. C. R. Alfred

The elastic anisotropy factors, c4,/c6,, c3,/cll, and c12/cl,, for hcp metal crystals vary significantly among the dgferent unalloyed metals. Significant variations with temperature are also found. The effects of elastic anisotropy on the dislocation in an elastic continuum with hexagonal symmetry have been investigated by computing the elasticity factors for the self-energies of dislocations in fourteen different metals at various temperatures where the elastic moduli have been reported. For most of the metals the effects of the orientation of the Burgers vector, dislocation line, and glide plane are small and isotropic conditions can be assumed without significant error. Significant effects of anisotropy are, however, found in Cd, Zn, Co, Tl, Ti, and Zr. The elasticity factors have been applied in the calculations of dislocation line tensions, the repulsive forces between partial dislocations, and the Peierls-Nabarro dislocation widths. It is predicted that the increase in elastic anisotropy with temperature in titanium and zirconium makes edge dislocations with (a), (a + c), and (c) Burgers vectors unstable in basal, pyramidal, and prism planes, respectively. The probability of stacking faults forming by dissociation of Shockley partials in basal planes also decreases with increasing c4,/c6, ratio, when the stacking fault energy is greater than 50 ergs per sq cm. The widths of screw dislocations with b = (a) in titanium and zirconium increase very significantly in prism planes and decrease in basal planes as c4,/c6, increases. The effects of elastic anisotropy on various dislocation properties in cubic crystals have received considerable attention during the past few years. In the case of cubic symmetry the departure from isotropic elasticity depends entirely on the shear modulus ratio, A = 2c4,/(cl, —c12); i.e., the medium is elastically isotropic when A = 1. Foreman1 showed that an increase in the ratio A produces a systematic lowering of the dislocation self-energy for a given orientation and Poisson's ratio. ~eutonico~, has shown that large anisotropy can have a marked effect on the formation of stacking faults by the splitting of glissile dislocations in (111) planes of fcc and (112) planes of bcc crystals. ~iteK' made similar calculations for (110) planes of bcc metals. Both studies of bcc metals showed that the large A values encountered in the alkali metals tend to reduce the repulsive forces between Shockley partial dislocations. In fcc metals, however, A does not vary over the large range encountered in bcc metals; consequently, the effect of A on the forces between Shockley partials is masked somewhat by the differences in Poisson's ratio between metals. The effect of A on the line tension of a bowed out pinned dislocation has also been investigated for cubic crystals, first by dewit and Koehler5 and more recent- ly by Head.6 In both cases the line energy model is applied and the core energy is not taken into account, thus making the conclusions somewhat tenuous with regard to the physical interpretation. Nevertheless, the fact that a large A decreases the effective line tension is clearly evident and the tendency for large A to produce conditions that make a straight dislocation unstable (negative line tensions) also seem evident. Head, in fact, shows visual microscopic evidence that stable V-shaped dislocations occur in 0 brasse6 For hcp metals the definition of elastic anisotropy is more complex and, furthermore, significant deviations from an isotropic continuum are found among a number of real hcp metals, especially at higher temperatures. The present work was carried out to survey the effects of elastic anisotropy on the elasticity factors, K, that enter into the calculations of the stress fields around a dislocation core. Some isolated analytical calculations have previously been carried out for several hcp metals but they are restricted in the dislocation orientations and temperature.8'9 The present computations are based on single-crystal elastic moduli that have appeared in the literature and consider various orientations requiring numerical computations. The results are then applied to survey the effects of temperature on the dislocation line tension and dislocation splitting in hcp metals. PROCEDURE Anisotropy Factors. The degree of elastic anisotropy in hcp crystals cannot be described by a single parameter, such as the A ratio in cubic crystals. The following three ratios must be simultaneously equal to unity in order to have an elastically isotropic hexagonal crystal: The magnitudes of these ratios at several temperatures, as computed from the existing data for the elastic moduli of unalloyed hcp metals, are given in Table I. There are no cases of complete elastic isotropy, but the large anisotropy ratios encountered in the cubic alkali metals are also missing. There are, however, several significant differences among the hcp metals, the most notable being the relatively small A and B ratios in zinc and cadmium and the differences in the magnitudes and temperature dependences of A. It has been noted that the temperature dependence of A has a consistent relationship to the occurrence of the hcp — bcc tran~formation. For cadmium, zinc, magnesium, rhenium, and ruthenium, A is less than unity at 4'~ and, with exception for rhenium, decreases with increasing temperature. In the case of rhenium, A has essentially no temperature dependence between 923' and 1123"~, so that it is clear that A does not approach unity at higher temperatures. Cobalt is similar to the above-mentioned group of metals in that it also does

Jan 1, 1969

By J. A. Bailey, J. H. Tundermann

The dihedral angles of the solid-liquid interfaces were measured at various temperatures above the solidus and the interfacial energies calculated when small additions of copper, indium, lithium, magnesium, antimony, and silicon were made to an aluminum alloy containing 3 pct Sn. When the results were compared with those of the Al-Sn alloy some differences were found which could be interpreted in terms of the ability of the added element to enter into solution or form intermetallic compounds with the aluminum and tin. It was shown that in some cases considerable changes in the shape of intergvanular liquid films can be brought about by comparatively small compositional changes in the alloy. DURING the melting or solidification of an alloy a temperature range is usually found where the presence of a liquid phase may be detected at the grain boundaries of a solid. It is believed that the presence of this liquid phase is responsible for hot tearing in castings and welds and hot shortness in the working of some alloys at elevated temperatures. Rosenberg, Flemings, and Taylor1 in a study of the solidification of aluminum castings have indicated the importance of intergranular liquid films and shown that their shape and distribution at the end of solidification effect the hot tearing characteristics of the material. The shape of such intergranular liquid films are determined largely by the ratio between the solid-liquid interfacial energy (yLS) and the grain boundary energy (ySS). A measure of this ratio (yLS/ySS , relative interfacial energy) is the dihedral angle 8. The dihedral angle 0 is related to the relative interfacial energy by the following expression: Rogerson and Borland 2 have also suggested that the shape of the intergranular liquid is an important factor in determining the susceptibility of a material to hot shortness. They showed that on a comparative basis materials having the lowest dihedral angles at a given temperature gave the greatest severity of cracking. They stated that liquid in the form of globules should be less harmful than liquid in the form of extensive films as more intergranular cohesion should be possible. Rogerson and Borlland 2 also showed that the susceptibility of an A1-Sn alloy to hot cracking can be reduced by small additions of cad- mium. It was found that the cadmium gave an increase in the dihedral angle at all temperatures. Ikeuye and smith3 investigated changes in the dihedral angle and relative interfacial energy with temperature for a number of ternary alloys formed when small additions of bismuth, cadmium, copper, lead, and zinc were made to an A1-Sn alloy. They found that in most instances changes in the dihedral angle were caused by compositional changes in the liquid phase; as the composition of the liquid approached that of the solid the dihedral angle decreased. They noted that the addition of a third element which was soluble in both the liquid and solid phases at a given temperature may decrease the dihedral angle (e.g., the addition of copper or zinc) but otherwise the ternary alloys formed exhibited dihedral angles between those of the A1-Sn binary alloy and those of the binary alloy of aluminum with the added element. Dwarakadasa and Krishnan4 investigated the changes in dihedral angle and relative interfacial energy with temperature when small additions of magnesium, iron, silicon, manganese, sulfur, cobalt, and silver were made to a copper alloy containing 3 pct Bi. They found that in all cases the added elements gave an increase in the dihedral angle and relative interfacial energy when compared with the values obtained for the simple binary alloy at the same temperature. It was noted that an increase in temperature gave a decrease in dihedral angle and relative interfacial energy in each of the ternary alloys studied. Similar results have been obtained by Ramachandran and Krishnan5 for the addition of small quantities of lead. This paper describes the application of dihedral angle measurement to the determination of the shapes of liquid phases at various temperatures above the solidus when small additions of copper, indium, magnesium, lithium, antimony, and silicon are made to an aluminum alloy containing nominally 3 pct Sn. An attempt is made to correlate the measurements with the relative solubility of the added elements in tin and aluminum. The work was undertaken to provide more data concerning the effects of temperature and composition on the shape of liquid films above the solidus. EXPERIMENTAL PROCEDURE In the present work ternary aluminum alloys containing nominally 3 pct Sn and small additions of high-purity copper, indium, lithium, magnesium, antimony, and silicon were made. The alloys were melted in a graphite crucible under an inert atmosphere of argon and cast into ingots 6 in. long by 0.5 in. diam. The ingots were then cut into rods 1.5 in. long, given a 50 pct cold reduction, and machined into test pieces 0.5 in. long by 0.5 in, diam for heat treatment. The alloy samples were annealed at the various test temperatures between the liquidus and solidus for approxi-

Jan 1, 1967

A mine that staggers the imagination is Chuquicamata, the granddaddy of them all. In 1968 production exceeded 300,000 tons of copper. Production began in 1915 and mining proceeded solely on oxide ores until 1953 when the first treatment of sulfides began. Today the company has mined about 1.2 billion tons of all types of material since inception. The accelerating rate of output can be gauged by the comparable 1946 figure of production-to-date which was 350 million tons. No single mine comes close to touching Chuqui for productivity at its high annual metal yield mining only 90,000 tpd of ore at the luxurious waste-to-ore ratio of 0.6 to 1. However, the complexity of the operation is enormous and the experience required to synchronize the various processes is masked by normal operations and only becomes apparent in times of emergency such as when the slide took place in the pit in February.

Jan 11, 1969

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

We remember him as a messmate, as a roommate, and when we rubbed shoulders with him on the square, for his kindly thought and unassuming manners. The Spanish grippe has claimed many from our depot. As we read down the names we pause here and there to recall some incident to establish permanently in our memory as a link to bind us, the living, with the dead. "And there's one name we cannot pass So we pause, and ponder awhile. And recall all his cheery words, And his smile—his perpetual smile." Men detained in the Quarantine Camp will have cause to remember him too, for he displayed his gentlemanly bearing and courtesy to all he came in contact with. Lieutenant Norman Lloyd Ohnsorg First Lieutenant Norman Lloyd Ohnsorg died in Nashville, Tenn., on Oct. 11, 1918. He mas born in St. Louis, Mo., Jan. 10, 1889, and lived in that city until he was 11 years of age when his parents removed to Iron Mountain, Mo., where he spent the next 6 years. On Jan. 10, 1906, he entered the Missouri School of Mines and Metallurgy at Rolla, Mo., and graduated from that institution in 1910, receiving both the Bachelor of Science in Mining Engineering and the Engineer of Mines degrees. In 1912, he received the degree of Bachelor of Science in Metallurgy, and in 1916, the degree of Metallurgical Engineer. After leaving college he wae connected with the following companies: Noble Electric Steel Works, Heroult, Shasta Co., Cal.; Mammoth Copper Mining Co.. Kennett, Cal.; St. Joseph Lead Co., Herculaneum, Mo.; Granby Smelting & Mining Co., Neodesha, Kans.; The Phosphate Mining Co., Nichols, Fla. While with the last company, he volunteered, in April, 1917, for service in the engineering corps of the U. S. Army. He passed an excellent examination, was accepted and called to Washington and placed in Division T. of the Ordnance Department where he was engaged in research work pertaining to nitrogen. He was then ordered to Sheffield, Ala., where he was second in command of the construction of the Government nitrogen plants at Muscle Shoals. After the completion of the plants, he was ordered to Buffalo, N. Y., on Sept. 28, 1915, to inspect and report on a government plant. After completing this work, he was called back to Sheffield. He left Buffalo on Oct. 6, but delayed trains caused him to miss connections in Cincinnati where he had to wait 12 hours. He had not beedfeeling well for

Jan 1, 1920

By R. J. Wasilewski

Axial expansion has been determined by X-ray diffraction up to 600° to 760°C in a titanium and four high-oxygen alloys. Expansion data cannot be fitted to the usual quadratic expression and anomalies observed are believed indicative of the changes in the bonding configuration of the valence electrons. Furthermore, there is significant disagreement between data obtained on poly crystalline and single crystal powder specimens. The major disagreement occurs within the temperature range (-470°C) where both mechanical and electrical properties also show markedly anomalous behavior. X. HIS work forms part of an investigation of physical properties of pure titanium and its osolid solutiono alloys with oxygen and nitrogen. In view of the anomalies observed in both the electrical resistivity' and the susceptibility behavior it was decided accurately to determine the thermal expansion behavior of the pure and alloyed a titanium. PREVIOUS WORK The axial expansion coefficients reported for pure titanium are listed below. As can be seen, there is a marked discrepancy between the axial expansion and the experimentally determined coefficients on poly crystal line material. Thus, if we take the most recently reported axial expansivities3,4 we obtain perature interval of 25o to 700°C. The experimental value reported for polycrystalline metal is, however, of the order of 9.7 x 10o6 per OC. EXPERIMENTAL I) Pure Titanium. High purity titanium powder of -325 mesh was used throughout most of this work. The only significant impurities present were the interstitials, oxygen and nitrogen, which analyzed respectively 650 and 80 ppm. The purity of the ma-

Jan 1, 1962

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state's annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state's annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By E. Hoek

The stability of a rock structure depends primarily upon the extent to which fracture develops within the structure, The prediction of the extent of potential fracture, the first step in the study of fracture development, involves a knowledge of both the stress distribution in the structure and the criterion which governs rock fracture under various stress conditions. While a great deal of research effort has been devoted to the development of techniques for analyzing the stresses in mining and civil engineering structures1-3 and to the investigation of the fracture mechanism of rock 4-6 relatively little attention has been paid to the application of available knowledge to the solution of practical engineering problems. This paper describes a photoelastic technique for the determination of potential fracture zones in certain types of rock structures. A practical example, based upon a problem which might be encountered in designing the layout of deep-level mine excavations, is given as an illustration of the application of this technique. STRESS ANALYSIS AND ROCK FRACTURE In deciding upon the technique to be used for the solution of a problem involving the prediction of rock fracture it is necessary to consider: 1) What type of stress information is required to satisfy the fracture criterion for rock; anti 2) How this information can most conveniently be obtained. It has been established, both theoretically 4,7 and experimentally 5,6,8that the fracture of hard rock depends primarily upon the relationship between the algebraically greatest and the algebraically smallest of the

Jan 1, 1967

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

IN GATHERING material for this chapter on Yerington and the one to follow on Silver Bell, the A.S.& R. project near Tucson, Arizona, I was fascinated at the way the two stories paralleled each other. For example, here are a few instances: (1) The first copper mining in the Yerington district of Nevada was in the late 1860's; the first in the Silver Bell area in 1873. (2) Each district was served by a branch railroad about 25 miles long from a main line of the Southern Pacific (by quizzical coincidence); and, in each instance, the railroad was later abandoned and torn up. (3) Each district had a sizable blast-furnace smelter ten or fifteen miles from the principal mines, and in each instance the smelter was later dismantled for junk. (4) Up to 1954, the Yerington district was credited with a production of 100,000,000 lb of copper; the Silver Bell district with 80,000,000 lb. (5) In each district the entire production had come from deposits other than the low-grade ore bodies now being exploited. (6) In each instance, existence of the low-grade deposits of the Porphyry type was recognized in the period circa1910-1914 and a substantial amount of exploratory drilling had been done, on one deposit at Yerington and on two at Silver Bell. (7) In each instance, the properties containing the Porphyry ore were acquired by a strong company (Anaconda Copper Mining Company at Yerington and American Smelt-

Jan 1, 1957

By W. Rall, A. J. Birkle

The effect of fast-neutron irradiation on the micvo strcture of a common reactor pressure-vessel steel, A212 Grade B, was studied using thin-foil transmission electron microscopy. The dislocation density of the irradiated material is considerably greater than that of the nonirradiated control material. Annealing studies indicated that dislocations and hardness ill the irradiated material annealed out—as docs the radiation-induced embrittlement according to other- investigators— at temperatures STEELS in nuclear reactors are affected by neutron irradiation. In the American Society for Testing Materials (ASTM) A302B and A212B steels commonly specified by designers for reactor vessels, between 650° and 800°F. However, the dislocations and hardness in control samples cold-worked to 9 and 70 pct did not anneal out readily, and a high dis -location density was observed, even after a 1-hr anneal at 850°F. Based on the hypothesis that cllrster defects, rather than the increased dislocation density, are primarily responsible for mdicltiotz-iudziced e)nbriftlen7ent, reconzmendations are made for reducing the susceptibility to such ernbrittlement. exposures at a temperature of 550°F or lower to neutron dosages encountered during a 20- to 30-year life (-3 X 10'' nvt, >1 mev) may increase the nil-ductility transition temperature (NDT) as much as 300" or 400".'9 Therefore, to prevent brittle failures in reactor structures, extreme caution is required to reduce thermally induced stresses during all reactor shutdowns and startups when the temperature is below the NDT of the pressure vessel.

Jan 1, 1964

By H. B. Charmbury, D. R. Mitchell

Recovery of fine coal from solids reporting to wash water has become increasingly important. These solids range from about 28 mesh to 0 and constitute 3 to 7 pct by weight of the feed tonnage to a coal preparation plant. In the past they were usually wasted to streams, but present clean stream legislation makes it necessary to remove them from the wash water and, if economically possible, recover the associated coal as a saleable product. Where these solids are not wasted to streams or to slime ponds they are recovered by thickeners and filters. Since filter cake is often high in ash or sulfur, or both, it is not readily marketed or used. Common practice is to mix it with other plant products, generally slack or cleaned run-of-mine. Uniform blending is difficult, not only because the impurity is usually high, but also because during certain operating periods it is possible to get a concentration of this filter cake in a railroad or barge. At some plants filter cake has been derived from the froth flotation clean-up of Dorr thickener underflow. The operating circuits required for a froth flotation plant make this a comparatively high-cost treatment, and in the last few years experiments have been carried out with bulk oil methods. These also are quite expensive and lend themselves only to special situations. Table I gives some characteristics of thickener underflows for plants in the Pittsburgh area treating Pittsburgh seam coal. It will be noted that there is a concentration of impurities in the -200 mesh sizes.

Jan 1, 1960

By W. C. Winegard, C. J. Simpson

BNINGESSNER et al.1 have shown that the solidification substructure in dilute cadmium alloys persisted after repeated deformation, recrystallization, and annealing treatments. On the basis of this and similar evidence, Whelan has suggested in a recent publication' that the solidification structure might affect the mobility of grain boundaries even after primary re-crystallization. This suggestion is important, since the technique used by previous investigators3-5 to fabricate grain growth specimens consisted only of casting, deforming, and recrystallizing prior to the grain growth anneal. Usually no attempt was made to homogenize samples with prolonged annealing. Experiments. To test the Whelan hypothesis, grain growth experiments were performed with samples in which the degree of solute segregation was altered by controlling the solidification rate of the alloys. The initial experiments were performed on the Pb-Ag system. Alloys containing 0.01 at. pct Ag were produced from 99.9999 pct Pb and 99.999 pct Ag. Cylindrical samples, 40 cm long and 12 mm in diam, were solidified in graphite-coated Vycor tubes by lowering them through a vertical furnace at varying rates with the furnace power settings constant. Six-centimeter sections were discarded from each end, and the 28-cm section from the center was cut into sections 25 mm long for grain growth experiments. These samples were deformed with the aid of a drophammer to a uniform thickness of 5.7 mm. After almost instantaneous recrystallization, the samples were given a grain growth anneal for various times at 260°C in a salt bath. Experimental results are shown

Jan 1, 1970

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965

By Clifford S. Wilson

ScReened pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments: a. Cossolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1933

By Charles Y. Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders % in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: CoMPressiON, Average Length, Series Pounds Inches 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series consisted of 17 specimens lettered 0, B, C, D, E, F, G, H, I, J, K, L, M, N, P, Q and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for 1/2 hr. at the following temperatures: TEmpeRa- TempeRa- Letters tuRe,° C. LettERs tuRe °C. B............................... 250 J.............................. 650 C............................... 300 K............................. 700 D............................... 350 L.............................. 750 E............................... 400 M............................. 800 F................................ 450 N............................. 851 G............................... 500 0. . :........................... 900 H............................... 550 P.............................. 950 I................................ 600 Q............................. L000

Jan 1, 1926