Search Documents

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By O. W. Ellis

THE question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,1 Iwasé,2 Lobley and Jepson3 stand preeminent. SOLUBILITY OF . GASES IN. COPPER Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate-possibly 30° to 60° C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1928

By Virgil Kirkham

NORTH AMERICA has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers. The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of , the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By Henry M. Howe

The striking features of American Bessemer practice aré its large output and its low initial silicon and initial temperature. These are interdependent. Large outputs implies short blows and short intervals between blows. Short blows imply low silicon and fast blowing. Low silicon implies short intervals and fast blowing. Our blows are short because we have little silicon to remove, and because we remove it fast by supplying blast rapidly. We get enough heat even with little silicon, because our blows and the intervals between them are so short that relatively little heat escapes from our vessels. Were we to lengthen our intervals, or to blow more slowly, we would have to meet the increased loss of heat from our vessels, either by using more silicon, or by melting hotter, i.e., by burning more coke, in the blast-furnace or in the cupola. Finally, our short intervals imply powerful machinery, efficient organization, and extreme specialization and subdivision of labor, which can be profitable only when the output is large. Let, us now take these points up in more detail, first glancing at some examples of our large outputs, given in Table I., and of the composition of our iron. Output.—On presenting such results to some foreign metallurgists, I have been told, " Oh yes, we quite understand that. You really turn out no more steel than we do. As a matter of personal pride, your manager gets up a tremendous spurt for a day, or even a week, crowds on men wastefully, rushes through great quantities of metal, and then for months afterwards has to recuperate. The machinery has been strained ; the owner's money has been wasted ; the men have been prostrated—all to gratify the manager's vanity. Your average output is no larger than ours." Personal pride has, doubtless, played its part; without it we would still be savages, or apes, or mollusks, if you prefer. These baser motives are the mudsills of progress, the soiled roots of that growth of which civilization is the flower. Great outputs were made

Jan 1, 1891

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

By George J. Clark

One of the major problems of operation in the anthracite industry is the disposal and handling of refuse—not because of its complexity but because of the quantity and type of material involved. It is the purpose of this paper to describe the kinds of refuse, methods of disposal, quantities of material to be handled and equipment used, together with present day application at specific operations in the Northern, Eastern Middle, Western Middle and Southern anthracite fields. For the purpose of this paper, refuse is considered to be any material that has no present or foreseeable future value and that must be handled and disposed of in the process of mining and preparing anthracite for market. Included in this classification are tunnel rock, mine rock, cleaner plant refuse, breaker refuse, old timber, ashes and silt. Disposal Methods Old timber is disposed of either by burning or by depositing on the refuse bank. Burning is preferred because timber on the refuse bank is a potential fire hazard. Ashes are deposited on a separate bank, mixed with other refuse, or flushed into old mine workings. In many places, the latter practice has caused considerable difficulty in preparation of coal mined from these areas. In depositing ashes on the surface, it is wise to refrain from mixing them with material containing coal as such contamination may prevent reclamation of the coal in future years. Tunnel work, mine rock, cleaner plant and breaker refuse compose the bulk of the material to be disposed of and handled, and are referred to collectively as "refuse" in this paper. Waste material in or adjacent to the coal beds may be removed at the working face wherever possible. This can be done in flat or lightly pitching beds, and in the Northern field represents a sizable percentage of this type of refuse handled. In the other three coal fields, this method of disposal cannot often be used. Refuse not removed at the working face is taken to the surface and generally is deposited on banks; occasionally it is crushed and flushed into old mine workings. Breaker refuse often is used for constructing berms for silt-retention basins. Disposal Problems The problem of handling refuse is different for each operation, owing to topographical conditions, quantity of material to be handled, anticipated requirements and types of equipment in use elsewhere at the operation. Preparation plants with limited refuse-disposal areas, excessive grades to reach the required elevation and long hauls to disposal areas not readily accessible require the selection of equipment to best meet the conditions. The quantity of refuse to be handled from a given amount of raw material varies considerably throughout the four fields. In mine coal, this varies from a low

Jan 1, 1949

By Feridun A. Albayrak

Jan 1, 1985

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design a power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanism of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived. Basic recommendations for mill speed and liner configuration are also presented

Jan 1, 1984

By D. Dever, E. S. Fisher

Measurements of the temperature dependence of the elastic moduli in single crystals of hep ruthenium, rhenium, cobalt, dysprosium, and erbium were carried out for various temperature ranges so as to investigate the correlation, suggested by prior work, between the shear anisotropy ratio, A = C44/C66, and the occurrence of the hcp — bee phase transformation. These measurements confirm the suggestion that A has a positive temperature dependence in that group of hcp metals that undergo thermally induced transfornzations to the bee structure and a negative or zero temperature dependence in the other hcp metals. It appears, from indirect evidence, that the hcp -fee transformation in cobalt is preceded by a highly negative temperature dependence of A. These results indicate that elastic anisotropy is an important factor in determining the temperatures at which martensitic phase transformations occur. Two possible roles for elastic anisotropy are proposed: 1) the shear-modulus ratio within the habit planes must be nearly similar for the two phases and 2) a large anisotropy decreases the stress necessary for the movement of the transfornzation dislocations. FUCHS&apos; calculations of the elastic moduli in the alkali metals have shown that the high shear-anisotropy ratios, c/c&apos;, in certain bee metals and alloys are the result of large negative contributions to c&apos; = (c11 - c12)/2 arising from the nearest-neighbor repulsive forces.&apos; On this basis, and following Zener,2 the association between high c/c&apos; ratios and the martensitic phase transformations that occur upon cooling certain bee metals is explained as a unique characteristic of the bee structure. Recent measurements of the elastic moduli in hcp titanium and zirconium show, however, that a high elastic anisotropy also exists in these hcp structures at the temperatures at which they transform to bee upon heating3. If there exists a direct and consistent correlation between the elastic anisotropy in close-packed structures and the occurrence of transformations to the bee phases then there is evidently a need to re-examine the conclusions of Zener theory. Elastic anisotropy may also be the result of the effects of temperature on the stability of the low-temperature close-packed structures or it may play an important role in the mech- anism of the martensitic transformations. The present measurements were aimed at establishing the phenomenological correlation between elastic shear anisotropy in hcp structures and the thermally induced hcp —bee transformations that occur in the majority of the twenty-three hcp metals, as shown in Table I. Prior to the present work the temperature dependence of the anisotropy ratio, A = c44/c66, was known at various temperatures for nine of the metals listed. The data showed a negative temperature dependence of A for cadmium, zinc, magnesium, and cobalt, which do not transform to bee, and a positive temperature dependence of A for thallium, zirconium, titanium, hafnium, and yttrium. The correlation was, however, ambiguous in that these two groups of metals are also separated with respect to the c/a ratios as noted in Table I. There remained the possibility that the temperature dependence of A is a function of c/a and not consistently associated with the transformation. The measurements of the elastic moduli in rhenium and ruthenium, in which hcp —bee transformations do not occur, were needed to help decide this question. The studies of dysprosium and erbium were undertaken to determine whether the correlation holds for the heavy rare earth metals.

Jan 1, 1968

By P. J. Carroll, H. Colijn

Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. Feeder load, material properties, feed rate, physical layout, and environment as well as first cost determine the selection of feeder type. This paper provides a new method of calculating feeder loads with some experimental data as verification. General design criteria for belt and apron feeder, rotary table and plow feeders are discussed and a special section is devoted to vibratory feeders. Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. During the past few years various papers have been written and presented on feeders and their application.1-9 This paper will be confined to some specific bin-feeder design criteria such as feeder load and power requirements. Special attention is given to the basic design criteria for vibratory feeders. HOPPER AND BIN DESIGN Feeders must be considered an integral part of the over-all bin and feeder system. Improper design of either one of these parts will affect the performance of the whole system. A lot of effort has been devoted in the past decade to the development of functional design criteria for hoppers and bins.1,10 The integrated concept of bin and feeder design requires quantitative analysis of the bulk material characteristics before the design and the selection of components can be attempted. The design of a feeder system must begin with the proper dimensioning of the hopper outlet to prevent arching or ratholing. The hopper opening should be large enough to allow passage of the bulk solid at the required maximum discharge rate." A feeder can only throttle the flow. FEEDER LOAD DETERMINATION Over the past ten years, there have been various attempts to determine the exact load or pressure on feeders mounted directly under hopper openings. Many designers, however, still consider this pressure equal to the hydrostatic head of material above the opening, and because such pressure would be very

Jan 1, 1969

By Thomas T. Read

Jan 1, 1913

By C. S. Westerberg, C. P. Heiner

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By John H. Hollomon, C. Zener

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik&apos;s analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By C. P. Heiner, C. S. Westerberg

Observation of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging mas accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. Castle Gate D Seam Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah, and thence in semicircular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,ooo ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. I). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 60 to 80 ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed.

Jan 1, 1942

By David R. Mitchell

THIS paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual,1 it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. HISTORICAL SUMMARY The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and sizing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By P. A. Beck, S. Kohara, M. N. Parthasarathi

IT has been shown1,3 that many observed phenomena related to annealing textures in f.c.c. metals can be adequately accounted for, at least in a qualitative way, by considering the orientation dependence of the boundary mobility, without any hypotheses concerning preferred orientation of nuclei. It was noted1 that this approach is particularly successful in the common cases of primary recrystallization in highly cold-worked polycrys-talline metals, where nuclei occur in great abundance, and that in the other extreme case, where the number of nuclei is very limited, or even only a single crystal is grown, the orientation dependence of boundary mobility has only a small effect, or none at all, on the orientations resulting from annealing. Recently Dunn described examples3-6 where observed secondary recrystallization textures apparently cannot be accounted for on the basis of oriented growth alone, but also require oriented nuclei, or at least the absence of nuclei in certain orientation ranges. In general, the great difficulty in correlating the preferred orientation of recrystallized grains with that of nuclei is inherent in the fact that nuclei are by nature very small, and that they are usually identifiable as "nuclei" only after growth, i.e., after they have already been subject to growth selectivity. An investigation was carried out by Liebmann and Lücke,&apos; and also a very similar one by Graham and Cahn,&apos; to obtain quantitative information on the orientation depend- ence of boundary migration rates in the recrystallization of slightly deformed aluminum single-crystal rods or plates, in which artificially nucleated recrystallized grains of predetermined orientation were grown. Liebmann and Lücke foupd maximum boundary mobility for boundaries across which the misorientation corresponded to a rotation of 40 deg around a common [Ill] axis, in accordance with earlier conclusions.9,1 Also, they confirmed that such an orientation relationship predominates among crystals growing into slightly extended single crystals from presumably random artificial nuclei. On the other hand, Graham and Cahn found no preferred orientation among crystals grown in a similar manner. It is not as yet known how these observations may be reconciled with each other. The view has been expressed in various papers5&apos;10,21 that selective growth based on the orientation dependence of boundary mobility is not in itself sufficient to account for the formation of sharp re-crystallization textures, such as those often observed in highly deformed polycrystalline metals after annealing. The present work was undertaken to ascertain whether or not it is possible to obtain a sharp re-crystallization texture in a case where random nuclei are assuredly present in large numbers. It was previously found1&apos; that high-purity aluminum crystals rolled 80 pct on the (110) plane in the [1T2] direction, when suitable precautions are taken, may be annealed for periods of about 1000 sec at 350°C without recrystallization. It was also found that the reluctance to recrystallize in this case is due to the scarcity of material in sufficiently deviating orientations to serve as nuclei. By using such a matrix,

Jan 1, 1959

By J. Chipman, J. C. Fulton

Reduction of Si from slag to carbon-saturated iron is a very slow reaction. The rate is nearly independent of stirring but is accelerated markedly by increased temperature. In a slag containing 45 pct SiO2, 38 pct CaO, 17 pct Al2O3, the energy of activation is approximately 130 kcal. AT temperatures of 1450" to 1600°C occurring in the hearth of the iron blast furnace, chemical reactions are normally expected to proceed with great rapidity. Many of the reactions of iron making are indeed quite rapid and attain a condition corresponding roughly to a state of equilibrium before metal and slag are tapped from the furnace. The one conspicuous exception is the reaction by which carbon in the coke or metal reacts with silica in the slag to deliver silicon to the metal. From the practical viewpoint the slowness of this reaction is indeed fortunate, for if it were fast enough to reach equilibrium during the time of contact, it would be difficult to produce pig iron of the desired low silicon content. The one other reaction which under certain circumstances can also be very slow is the transfer of sulfur from blast-furnace metal to slag. In their laboratory exeriments on this reaction, Hatch and Chipman found that at least 5 hr were required for the attainment of equilibrium in a small crucible and that the reaction was not accelerated by increasing the rate of stirring. Subsequently it was shown2 that the presence of a reducible oxide MnO greatly inhibited sulfur removal, and finally that SiO2 itself3 under some conditions has sufficient oxidizing Dower to interfere with sulfur transfer. The kinetics of sulfur removal are now rather well understood,4 and it has been shown3,5 that when the silicon content of the metal is high enough to prevent reduction of SiO,, the desulfurizing process is rapid. Thus the observations of slow removal of sulfur are associated with the coincident slow reduction of SiO2, a process which transfers both silicon and oxygen to the metal phase. It is, of course, the oxygen which interferes with sulfur removal. An explanation of the slowness of the silica reduction reaction has not been obtained. The sulfur transfer process has been shown by the authors5 to be at least partially transport-controlled in the absence of interference by silica. Under the experimental conditions. 99 pct of the total transfer at 1600" was accomplished within an hour. Under similar conditions the reduction of silica may not proceed half-way to equilibrium6 in 8 hr. It is scarcely imaginable that silica reduction could be transport-controlled when the slag contains 44 pct SiO2 and the metal about 1.4 pct C. The experiments reported here show definitely that it is controlled by a slow step or steps in the chemical reaction. One might expect to find such a slow step in the breaking of SiO bonds or in the slow removal of oxygen by carbon at the slag-metal or metal-crucible interface or by bubble formation. EXPERIMENTAL PROCEDURE The experimental procedure used in this investigation was similar to that used in the study of the kinetics of desulfurization.5 A sketch of the graphite crucible and stirrer used in the current work is shown in Fig. 1. The quantity of metal and slag used was adjusted so that the slag-metal interface was located between the top and bottom blades on the stirrer; the top of the slag layer was above the top blade. The stirrer shaft was hollow down to the metal level and served as thermocouple well or optical pyrometer target. Stirring speeds of 0 to 500 rpm were used. A carbon monoxide atmosphere was maintained in the furnace by flushing the gas over the slag surface, except in run No. 220 when it was bubbled

Jan 1, 1960

By Albert F. J. Bordeaux

Alluvial gold was first discovered in Guiana in 1852, in the sands of the Arataye river, by Paulino, a Braziliaii convict. During the following years, gold was found also in the rivers Orapu, CirubQ, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Vat, and Couriege. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysee, Pas-Trop-Tot, date from 1878, and their production has been about %g5,000,000. In 1888, the Awa placers, along the boundary bet.ween the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company, the Dutch Guiana Freiich Minillg Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have produced about $18,000,000 in six years (1894-1900), but not even one-fourth of tho production went through French Quiana and

Jan 1, 1911