Search Documents

By D. Turnbull, J. E. May

THE (110) [001] texture in silicon iron is of considerable interest both from the technological and scientific points of view. Its occurrence was reported more than 20 years ago.1-4 The texture develops by means of secondary re crystallizatjon5 and can be very strong, that is, greater than 90 pct alignment even thouh the primary re crystallization texture is weak or complex. This behavior is in contradistinction to the face-centered metals which develop their strong secondary recrystalliza-tion texture from a strong primary recrystalliza-tion texture.', The microstructural changes accompanying the (110) [001] texture formation in silicon iron are as follows: When properly prepared cold-rolled sheet (i.e., 0.015 in. thick) is annealed at about 800°C, primary recrystallization occurs and a fairly stable fine-grained primary recrystallized matrix of about 0.02-mm-diam grain size is produced. The material at this stage does not have the strong (110) [110] texture. As the temperature is raised to about 900°C, relatively large grains appear in the finegrained matrix and they grow at the expense of the smaller grains to many times the sheet thickness. In time the complete sample is consumed by these large grains. This process of the growth of relatively few grains (about one in 105 primary grains) at the expense of many grains is called secondary recrystallization. Since all the secondary grains are of essentially (110) [001.] orientation, the strong texture is developed by this secondary recrystallization process. Theories of the (110) [001] texture in polycrystal-line silicon iron have been proposed by Decker and Harker and by Dunn.Decker and Harker have shown that grains initially in the (110) [001] orientation will upon annealing after cold-rolling, re-crystallize back to the initial orientation. To account for the sharp texture in silicon iron they propose that (110) [001] grains become more highly strained than grains in other orientations and therefore recrystallize first. They are then the lowest energy grains and can consume their higher energy neighbors. Grains in orientations other than (110)

Jan 1, 1959

By J. F. Smith, J. R. Ogren, N. J. Magnani

The uapor pressrcres of magnesium over binary alloys of magnesium with twelve of the yare-earth eletnetzts have been measured by the Knudsen effuion method in the temperature range 675° to 910°K. These vapor-pressure measurments were combined with data concerning the tevtrlitzul magnesium solubility and the vapor pressure of pure magnesinm to evaluale the standuvd free energies of pluase jormation. These free-etzergy values indicate that the CsCl structures of the heacy rave earths tend to be somewhat less stable than those of the light rare earths. This dif-]eying- behaviov covrelates with differences which have been obsevz~ed in other alloy systetns wherein a phuse appeurs, disappeavs, or changes crystal stvucture as the atomic number of the rare-earth com-ponent is changed. This behauior also appears to correlate with the struclurul rariations within the rare-earth elements themselves, and it is speculated that cariations in the spatial extent of the 4f orbitals are responsihle. STUDIES of the phase relationships and crystal structures in the binary systems between rare-earth metals (lanthanons) and magnesium are extensive but far from complete. However, the currently available information1-10 does produce a rather interesting pattern. This is illustrated in Table I. If one excludes europium and ytterbium from consideration because of their generally atypical behavior, it can be seen from the table that the phase relationships in the magnesium-rich regions show a distinctly different pattern for the lighter lanthanons as compared to the heavier lanthanons. For the lighter lanthanons, LnMg2 phases occur from lanthanum to gadolinium with the cubic MgCu2 structure, LnMg3 phases occur from lanthanum to terbium with the BiLi3 structure, and magnesium-rich phases occur from lanthanum to gadolinium with stoi-chiometries between Ln5Mg42 and LnMg12. In contrast, for the heavier lanthanons, those LnMg2 structures which have been examined have the hexagonal MgZn2 structure, LnMg3 phases have not been observed beyond terbium, and the magnesium-rich phases occur with the a manganese structure near a stoichiometry of Ln5MgZ4. The heavy lanthanon-magnesium systems thus appear to be analogous to the Y-Mg system""2 wherein YMg has the CsCl structure, YMg2 has the MgZn2 structure, and the region Y4Mgz5-Y5Mg24 has the a manganese structure, and no other intermediate phases are observed. Similarity in alloying behavior between yttrium and the heavy lanthanons occurs commonly, and on this basis it seems likely that LnMg2 phases will be found with the MgZn2 structure in the binary systems of dysprosium, thulium, and lutetium with magnesium when the appropriate investigations are made. In the case of the magnesium-rich phases of the lighter lanthanons, only the Ce-Mg phase relationships have been investigated thoroughly and in detail, and until similar investigations are made for the other systems there will remain questions as to which magnesium-rich stoichiometries represent equilibrium phases and what systematic variations occur in the sequence from lanthanum to gadolinium. Thus the data in Table I show that only the LnMg phases occur with the same crystallographic structure throughout the sequence from lanthanum to lutetium. It was speculated that the relative stability of these LnMg phases might vary from one lanthanon to the next in such a way as to presage the differences which occur among the more magnesium-rich lanthanon-magnesium phases. On this basis the present investigation of the thermodynamics of phase formation was Gndertaken for the LnMg phases. PROCEDURE AND RESULTS A generalized phase diagram for the lanthanon-rich portion of a lanthanon-magnesium alloy system is shown in Fig. 1 where ß represents a high-temperature bcc

Jan 1, 1968

By J. Absil, H. Dreissen

Upgrading low-concentration ores is of increasing importance today. The heavy medium cyclone process, due to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses separation efficiency, assessment of that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants, each handling a different mineral, are reported.

Jan 1, 1982

By Carl Swartz

FOR many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By F. W. Maclennan

ORE production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods. 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which, produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane1 and the second by D. B. Scott,1 and the third, together with a general, description of the mine, by J. H. Hensley, Jr.1 The geology of the district has been worked out by. Dr. F. L. Ransome.2

Jan 1, 1930

By R. E. Head

UNDER existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes.

Jan 1, 1936

By R. M. Murray

Although blister copper has been produced at the Mount Lyell Mining and Railway Company's works since 1896, it is only during the past five years that electrolytic refining has been undertaken locally, this having been done previously at customs refineries, at first in the United States, and afterwards at Port Kembla, New South Wales. Left to right: smelter building, converter building, blower building (in which converter-generators are housed), tank house and anode dock. Wire-bar furnace building in background at center. Possessing a hydroelectric power plant capable of generating power considerably in excess of the requirements of its mines and works at the time, the company was in a favorable position to undertake its own refining work, provided this advantage was not offset by the high cost of coal, which would have to be imported from the mainland, and provided also that the capital cost of the plant would not be unduly large in regard to the relatively small amount of copper to be treated. A study of these several conditions led to the adoption of a high-density plant using blister-copper anodes and equipped with an electric boiler to provide any

Jan 1, 1934

Jan 1, 1894

By L. K. Eigenbrod, F. Notaro

Enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969) has placed new responsibilities on the mining industry. The new law, aimed at eventually solving the problem of pneumoconiosis, sets new respirable dust standards at 2 mg per cu m. Techniques employed to date have been shown to lack total effectiveness in meeting the prescribed standards. Since it is possible that even the new standards will eventually have to be lowered to effectively attack the medical problem, the need for new and more reliable methods of assuring clean respirable air will intensity. This paper presents, in a preliminary manner, both the present technical capability and growth potential of cryogenic technology for supplying miners with clean breathing air. Work with two sizes of prototype supplied-air (cryogenic-liquid) respiratiors in Union Carbide's Fawn Coal mine, will be described. Other potentially fabricable systems will be discussed and a preliminary assessment made of the potential cost of introducing cryogenic air breathing systems in coal mine service.

Jan 1, 1972

CLEAR sunny skies that prevailed all through the 175th General Meeting of AIME were not the 1east of the details that resulted from the many months and man-hours of p1anning by the Southern California Local Section. Some 2600 persons left the 1953 Annual Meeting technically enlightened, having had a choice of over 300 papers presented by 400 authors to listen to, learn from, and criticize. During the meeting, Mike Haider turned over the Presidency of AIME for 1953 to Andrew (Drew) Fletcher.

Jan 4, 1953

By Ralph W. Bailey, William B. Price

INTRODUCTION ARSENIC, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in [ ] condenser tubes. This subject has been thoroughly covered by Barry,1 who described the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 [ ] lists them as "rhombohedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By Robert H. Carpenter

Major trends in exploration geochemistry during the past year included an increased level of geochemical exploration by both government and private industry: greater sophistication in sampling, analytical and interpretive techniques: and increased activity on the part of universities and state geological surveys. The evolution of applied geochemistry in North America from a useful prospecting tool to an invaluable exploration method is largely due to efforts of the mining industry, the USGS and the Geological Survey of Canada. In the U.S., there has been a distinct reluctance on the part of universities to conduct research or to offer courses dealing principally with applied geochemistry. Most university geochemists have not been responsive to industry needs because government sponsorship of geochemical research in universities has been overwhelmingly in favor of theoretical, rather than applied research: and, because of the mistaken notion that exploration geochemistry is not sufficiently academic. A critical shortage of specialists in this field has resulted. Specialists in Exploration Geochemistry Needed Based on the response to a brief questionnaire sent to universities in the U.S. and Canada, there is some evidence suggesting a reversal in this trend. Graduate courses devoted to exploration geochemistry are currently being offered in geology departments at the following universities: University of British Columbia, Colorado School of Mines, University of Idaho, McGill University, University of New Mexico, Pennsylvania State University and the University of Utah. Other departments report that applied geochemistry is included in general geochemistry courses. A survey of recent publications suggests increased research interest in exploration geochemistry by university geologists.

Jan 1, 1970

By Gregory Dybalski

The purpose of this paper is to illustrate the forecast capability of the econometric model of the cobalt industry1/ as utilized by the Federal Preparedness Agency. Forecasts from this model are illustrated from the premise that the leading producer continues production of cobalt. An alternate forecast is presented where the model structure is altered to reflect the condition where the leading producer leaves the market. All estimations and forecasts presented here are shown for illustrative purposes. The cobalt industry is highly concentrated; one company, owned by the Zaire government, accounts for approximately three-fifths of world production. The cobalt supply outside of Zaire is determined by the level of activity of copper or nickel markets, as cobalt is mined as a by-product of copper or nickel. The demand for cobalt reflects a diversified usage pattern; cobalt is used mainly in heat and corrosion-resistant materials, high- strength materials and permanent magnets. According to 1974 U.S. consumption data superalloys accounted for 22%, magnetic alloys 18%, cutting and wear-resistant materials 13%, and catalyst 7%. Foreign consumption is probably similar in terms of usage categories, but the relative order of the categories is in variance.2/ The Cobalt Model The cobalt model's object is to explain consumption, supply and price movements by utilizing statistically estimated equations. Central to the econometric model is the role of Zaire as the profit-maximizing "dominant firm". Zaire sets the price that is most profitable for itself. The price of cobalt depends on industrial demand, production of other firms, and net exogenous purchases, such as government

Jan 1, 1977

By John K. Kennedy

ThE basic equations describing continuous zone-melting via the zone-void method were reported by Pfann. Using these equations, a theoretical study was undertaken in this laboratory on the effect of the variation of the significant parameters of the zone-void system. These parameters are the zone length, 1, the heater length, h, and the effective distribution coefficient, k. The object of this study was to determine the effect of these parameters on and (where a = Cp/Cf and ß = Cw/Cf, Cp, C,, and Cf being, respectively, the solute concentration in product, waste, and feed) so that, in future application of this technique to the ultrapurification of materials, the effect of 1 and h would be predictable regardless of the value of k. The basic assumptions made by pfannl were, for the purposes of this study, assumed to hold. For k < 1, the steady-state solute distribution in the stripping section and the shift in this distribution brought about by passage of a void is shown in Fig. 7 of Ref. 1. In this section the definition of k and ß precludes the possibility of ß assuming values less than unity when k < 1. In the course of this investigation it was found that computations based on Pfann&apos;s equations gave values of ß less than unity in the region 1 > k > l/h for almost all values of Ls, where Further computations showed that 6 assumes negative values when k > 1 for many values of L,, 1, and h. A check of the derivation of the stripping-section equations showed that an error had been

Jan 1, 1964

By Paul A. Beck

While the recrystallization properties of most of the practically important metals are known in considerable detail, those of lead are still relatively little known in spite of some valuable contributions in recent years. This condition probably is due to the difficulties involved in applying the usual methods of investigation. The microscopic method of discriminating between the elongated deformed grains of the familiar lenticular shape and the equiaxed recrys-tallized grains is not successful with fully refined lead: lenticular grains cannot be seen under the microscope with any amount of deformation whatever. The probable cause of this phenomenon was recognized long ago. With large deformation the time of recrystallization at room temperaturc is shorter than the period of preparation of the specimen for microscopic examination; with small deformation the deformed grains arc not noticeably elongated in the first place. However, with small cleformation the migration of the grain boundaries can be observed. The only systematic investigations yet published on the recrystallization of lead, those by R. S. Russell, 1-3 make use of the conditions just described. Russell considered recrystallization completed when no further migration of boundaries could be observed. A serious objection to this method arises from the fact that there is no evidence to support the view that grain-boundary migration results only from recrystallization. If such migration does result from other sources after recrystallization is completed—after the deformed grains have been replaced by new unde-formed grains—the "time of recrystallization" as determined by Russell may be too long. Furthermore, the method is subject to the above.-mentioned limitation because of the unavoidable period of preparation of the sample. According to Russell, even with the fastest technique 5 min. clapsed before the deformed samples were ready for examination, and consequently no reearystallization time shorter than 5 min. could be measured. The lack of success in detecting the recrystallization of lead by the usual hardness or tensile tests is again caused by the time necessary for

Jan 1, 1940

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By W. Crafts, J. L. Lamont

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,&apos; as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By J. L. Lamont, W. Crafts

Selection of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of harden-ability,&apos; as-quenched hardness and tempered tensile strength.2 Ductility and toughness may also be estimated if the steel is completely hardened on quenching, 5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In finegrained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accom- panied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to. 4 in. in diameter. Procedure The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1030, 1040, 1340, 3310, 33167 4320, 43.30, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 931°, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.3; The bars were tempered as follows: 34 in., I in., and 1% in., 2 hr; 235 in., 3 hr; 4 in., ; hr. All bars were air-cooled from the tempering tem-

Jan 1, 1948

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry&apos;s annual fatality experience. In recent years workmen&apos;s compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera&apos; roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949