Search Documents

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By C. R. Ince

THE term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalcopyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggart1 has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls .dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This-is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 lb. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 lb. per ton were added to the thickened pulp and the whole

Jan 1, 1929

By K. E. Starling

Phase equilibria data were used to develop an equation-of-state correlation for complex hydrocarbon mixtures, thereby circumventing difficulties associated with use of pressure-volume-temperature data. Equilibrium phase data for two condensate reservoir fluids were used to determine equation-of-state parameters for hydrocarbons as heavy as C22H46 in a modified form of the Benedict-Webb-Rubin equation of state. Comparative tests of K-values from the resultant correlation were made with data for condensate reservoir, separator and gas plant absorber mixtures. Generally, for temperatures above OF and computed liquid densities below 0.55 Ib-mole/cu ft, the modified BIVR equation predicted K-values in close agreement with the experimental data. INTRODUCTION Accurate predictions of thermodynamic behavior for complex hydrocarbon mixtures are necessary for many calculations in the petroleum industry. Because of the relatively high cost of extensive experimental data, many correlations for prediction of phase behavior have been developed. Some of these, such as the correlation of K-values presented in the NGAA Equilibrium Ratio Data Book, are totally empirical.l Others, such as the Benedict-Webb-Rubin (BWR) equation-of-state method, are semitheoretical.2-4 Unfortunately, published correlation methods often do not accurately predict the phase behavior of complex hydrocarbon mixtures, principally because of inadequate representation of the effects of components heavier than decane. This paper presents a new approach to this problem in which basic equation-of-state relations including heavy hydrocarbon effects are applied. Equilibrium phase data for two condensate reservoir fluids containing hydrocarbons as heavy as C22H46 are used to correlate component K-values. The BWR equation was chosen as the prototype equation of state for this study because of its proven capability for accurately predicting phase behavior and thermodynamic properties of light - hydrocarbon mixtures? Research was directed toward development of BWR parameters for the heavy hydrocarbons and modifications of the mathematical form of the BWR equation for application to complex hydrocarbon mixtures. The new equation-of-state approach presented differs considerably from previous methods in that phase equilibria rather than PVT data are used for determination of equation-of-state parameters. It is an explicit approach since the parameters are determined directly from mixture data. As such, it does not encounter problems inherent in the implicit method used by Benedict, Webb and Rubin 2-4 and numerous other investigators—one in which mixture parameters were postulated to be functions of the pure component parameters. The pure component BWR parameters, in turn, were determined from experimental PVT data. This method has been limited to mixtures containing components lighter than decane because of lack of vapor phase PVT data. Studies have been reported in which BWR parameters have been determined explicitly from PVT data for binary mixtures.6-8 However, since small concentrations of heavier components have only a minor effect on PVT behavior, it is doubtful that these explicit methods would yield useful results for condensate systems. Ellington and Eakin9 have shown that the accuracy of K-values predicted by an equation of state developed from mixture PVT data probably would be more than an order of magnitude lower than the accuracy of the PVT data. On the other hand, an equation of state utilizing parameters developed from phase equilibria data should predict K-values with accuracy comparable to the accuracy of the experimental phase compositions. This work applies this explicit approach with the objective of improving hydrocarbon mixture phase behavior predictions. Results are evaluated by comparing predicted and experimental K-values at reservoir, separator and gas plant

Jan 1, 1967

By Frederick Prime

The first catalogue of Geological Reports of the United States was prepared by Prof. 0. C. Marsh, and published in the American Journal of Science and Ark for 1567, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought clown to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen : The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. R. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va.; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College; Mr. Sanderson Smith and Prof'. J. J. Stevenson, of New York; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers.

Jan 1, 1879

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

If problems are opportunities in disguise, the mining industry certainly had plenty of "opportunities" in 1975. Considering the industry's generally lackluster 1975 profit record, and in view of the slowdown in inflation, there's some hope that 1976 might be a better year in spite of the increasing risks and uncertainties that plague the mining industry.

Jan 2, 1976

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By T. D. Yensen

IN the investigation of the magnetic properties of iron-nickel alloys,1 it was found necessary in order to make the alloys forgeable, or malleable, to add small quantities of some other element. Iron-nickel alloys have been known for nearly a century, but have been made in commercial quantities only since 1885. Their remarkable mechanical properties were disclosed by Riley in 1889 and from that time on a large amount of research work has been done both to discover new properties and to correlate the results obtained.2 Lately the Bureau of Standards has collected the published data in a special circular3 giving in compact form an account of the properties of the iron-nickel alloys. It also contains a clear historical sketch of the development as well as a selected bibliography. The chief difficulty with the development of iron-nickel alloys was that the "pure" alloys do not forge readily. The addition of small amounts of manganese, however, made the alloys forgeable, and manganese has therefore come to be regarded as a necessary constituent of nickel steels. The present paper shows to what extent manganese is needed for various nickel contents and also what is the effect of other alloying elements on the forgeability. It also touches upon the cause of forgeability but refers to other sources for more exhaustive treatises, on the subject. The alloys were prepared by melting electrolytic iron and electrolytic nickel with of without other alloying elements in the desired proportions in a magnesia crucible in a vacuum furnace under a. pressure of 1 mm. mercury. The ingots weighing about 2 kg. were allowed to cool in vacuo. If pipes or blowholes were present, the ingots were cut in such

Jan 1, 1920

By Thomas Cox

The following compilations are made from a series of investigations and are used to present the subject in an unbiased manner, as the writer does not represent any company or financial interest. The present situation is complex. The producers are hard pressed by reason of the low price of crude, while the independent refiner is little better off, because of the corresponding cut in price of refined products, except on occasional contracts. If the real costs are analyzed, it will be seen that the land speculators and the lessors—royalty owners—make the larger profits and not the struggling legitimate operator or independent refiner. The present-day (October, 1922) posted prices per barrel for crudes are Kansas, Oklahoma, Mexia, Gulf Coast, and Louisiana..... $1.25 Healdton............................................. 0.75 Northern Texas and Central Texas...................... 1 . 50 Pennsylvania......................................... 3.00 Wyoming, Elk Basin.................................. 1.25 Wyoming, Salt Creek................................ 0.70 California Base..................................... 0.60 These prices are at the well. In addition, crudes must be gathered and transported to refinery (by pipe line or tank cars), refined, and the refined products marketed. These crudes are of various gravities, ranging within a narrow margin for each field or district, so that averages are not difficult to deduce, and it is these averages that really determine the average operating conditions. In order to show the present realizations, the prices and costs now obtaining are listed against the average yields; the figures are also adjusted VOL. urn.----71

Jan 1, 1923

By C. L. Clark, J. Russ

FOR many years attempts have been made to develop a laboratory test that would serve to indicate the proper temperatures to be used in the various hot-working applications to which metals may be subjected as they are being processed from the cast ingot to the desired finished products. That these attempts have not been very successful is indicated by the fact that most of the temperatures in use today in these operations have been developed over a period of years by trial and error. In other words, the selection of the proper temperatures for the hot-working of metals is generally an art rather than a science. Our knowledge with respect to the behavior of metals at elevated temperatures has been greatly extended during the past several years. While most of the work in this field has been done at proposed operating temperatures of equipment, rather than at processing or fabricating temperatures, one outstanding fact has been developed, which is applicable to the entire high-temperature range; that is, that the rate of deformation to which the metal is subjected is of the same order of importance as the temperature. The failure to properly recognize this fact has greatly retarded the development of a suitable laboratory test for determining hot-working temperatures. INFLUENCE OF RATE OF DEFORMATION ON HIGH-TEMPERATURE PROPERTIES It is not the intent of this paper to survey all the work that has been done on the effect of deformation rate on the properties of metals. The importance of this factor, however, was shown by Zay Jeffries1 as early as 1919, when he called attention to the existence of the so-called equicohesive temperature and to the effect of certain factors on the location of this temperature. Fig. I is a diagrammatic sketch showing the effect of temperature on the relative strength of the crystals and grain boundaries and the type of fracture that will result, depending on the location of the test, or working temperature with respect to the equicohesive temperature. Since the type fracture varies, it also follows that at temperatures below the equicohesive temperature the major deformation occurs in the grains; while at temperatures above, the deformation results either from the movement of the grains with respect to each other or recrystallization of the strained material occurs almost instantaneously, producing new crystals at the fracture. As previously indicated, it is an established fact that the position of this equicohesive temperature for any given metal is dependent on the deformation rate. For example, in 0.15 per cent plain carbon steel the location of this temperature under

Jan 1, 1945

By Will H. Coghill

In this investigation, the low-grade red iron ores of Alabama were examined by the use of "heavy solutions."' Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned; but when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imlaginable conditions. Concentrating machinery has not been tested in this investigation. When the properties of the ores have been gleaned, the machinery may be used more effectively. Alabama Low-grade Red Iron Ores The Bureau of Mines has undertaken by laboratory methods to select the best means of concentrating the low-grade iron ores of Alabama. These ores constitute the parts of the ore bed left by selective mining. If more of the ore bed could be included in the current output, the mining cost would be reduced and longer life of the district would be insured. This advantage would be reflected by added permanence of churches, homes, schools and every undertaking in the commonwealth. The red ores chosen for this study of effectiveness of grinding are too low in lime to meet the requirements of the blast furnace. If lime is

Jan 1, 1927

By Sidney Powers, Alfred C. Lane

This paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Bundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Chemistry, Mines Branch, Ottawa,' all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 mm. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grams per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 1, 1916

By Samuel Shallcross

THE principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the line-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania.

Jan 1, 1936

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By J. Chipman, J. C. Fulton

Reduction of silicon from blast-furnace-type slags by carbon-saturated iron is a very slow reaction even under conditions of rapid stirring. Equilibrium under atmospheric pressure of carbon monoxide was approached from both sides, and the silica-silicon relation was established at temperatures of 1425º to 1700°C for slags containing up to 20 pct Al2O3. Silicon carbide is formed by reaction of graphite with high silica slags and the conditions for its formation were determined. Activities of SiO2 and of CaO in their binary solutions at 1600°C were determined. The effects on the activity of SiO2 were established for additions of 10 to 20 pct AI2O3 and of 10 pct MgO. STUDIES of chemical reactions between blast-*>-5 furnace slags and metal have been focussed on the transfer of sulphur from metal to slag. The important role which silica reduction plays in this process' has led to a study of the transfer of silicon from slag to metal and the equilibrium represented by the equation SiO2 (in slag) + 2C (graphite) = Si + 2CO (g). [I.] The authors2 have published an account of the experimental method employed in attacking this problem and of three series of experimental results at 1600°C. This paper contains data on some additional compositions and extends the observations to cover the temperature range 1425° to 1700°C. The data are used to determine the activity of silica in the slags. As in the earlier experiments, the atmosphere was carbon monoxide which flowed through the furnace at 150 ml per min. In certain heats designated in the tables and figures, the gas was bubbled through the melt using a graphite tube. The latter increased in porosity during a run and in some cases bubbling ceased as indicated by cessation of surging. Some results were discarded for this reason. Experimental Results The new data are shown in Tables I through V and both old and new data are plotted in Figs. 1

Jan 1, 1955

By Charles McElroy White

IT is indeed an honor to have been asked to participate in the program which celebrates the seventy-fifth birthday of the American Institute of Mining and Metallurgical Engineers. This great organization has occupied an important place in the professional and industrial life of this country-of the world. Its members have explored the far reaches of our globe and have played a great part in the discovery, extraction and utilization of the mineral resources upon which our civilization so largely depends. These engineers, together with the restless prospectors, on the one hand, and the scientists, on the other, have literally been the advance scouts of our modern way of life. As such, we owe them a deep and lasting debt of gratitude. May I, therefore, wish many happy returns to the American Institute of Mining and Metallurgical Engineers and express the hope that it may long continue to be of great service, as it has been in the past. The subject assigned to me-Iron Ore and the Steel Industry-is, indeed, important, as one considers the future of our world. I shall give as few figures as possible. Pertinent statistical data are included in the tables in this chapter, which, I think, will prove interesting. Many studies of iron-ore reserves have been -published and are available; hence I shall limit myself mainly to an interpretation of these figures. The statistics data are from standard sources, including the Lake Superior Iron Ore Association, the American Iron and Steel Institute, the United States Bureau of Mines, the United States Geological Survey, the United

Jan 1, 1947

By S. A. LoPilato, J. T. Smith

SEVERAL techniques have been evaluated for cooling the throat area of rocket-nozzle inserts to prevent erosion or fracture of the inserts during exposure to high operating temperatures and pressures. Self-cooled composites, such as infiltrated tungsten, have shown considerable promise for these applications. These composites can be fabricated by infiltrating the refractory matrix with a lower-melting metal or non-metal which is insoluable in tungsten. During firing, the lower-melting substance undergoes a series of continuous endothermic phase changes which absorb sufficient heat to maintain the nozzle matrix material at or below a safe operating temperature. At present, the state-of-the-art has reached a point where the refractory matrix density and microstruc-ture have been established as the critical parameters to be controlled for optimum self-cooled performance.'" Nondestructive testing has been utilized to ensure that porous tungsten billets were of uniform density and free from cracks or other defects prior to fabrication into rocket nozzle inserts. Ultrasonic-velocity techniques have been employed because of their reliability and reproducibility. The purpose of this note is to present and interpret the test data developed for porous tungsten matrices. For evaluation purposes, tungsten powders with Fisher subsieve sizes of approximately 4 and 18 p have been obtained for study from four commercial sources: the General Electric Co., Wah Chang Corp., Fansteel Metallurgical Corp., and Kennametal, Inc. Porous tungsten matrices were fabricated from the powders by hot pressing in induction-heated graphite die assemblies. Typical billets ranged from 3 in. diam, 2 in, high to 5 in. diam, 5 in. high. The ultrasonic-velocity measurement technique employed was through transmission, pulse echo at a frequency of 1.0 mc using matched barium titanate crystal transducers. The testing equipment included a pulsed ultrasonic generator, an amplifier, a specimen holder, and an oscilloscope, as shown in Fig. 1. The porous tungsten thickness was measured to i 0.0005 in, with precision micrometers while the oscilloscope achieved 0.02 psec time measurement accuracy. The time for a sound wave to pass through the billet, the bulk wave velocity, was calculated to 0.5 pct using Eq. [l]: V-} where V = bulk wave velocity, in. per psec, T = specimen thickness, in., and / = time, psec. To develop inspection standards, the bulk density of a porous tungsten billet was determined by the ASTM water-immersion technique.3 The ultrasonic-velocity measurements were completed at seventeen positions for each billet and averaged to develop a characteristic standard velocity for a particular tungsten powder at several density levels. A plot of ultrasonic velocity vs density is presented in Fig. 2 for six different tungsten powders. This graph has been established as

Jan 1, 1967

By W. H. Basssett

THE amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hamper that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen.

Jan 2, 1926

By Joseph Chalmers, E. L. Rawlins, D. B. Taliaferro

PRoblems dealing with the movement or migration of fluids through porous beds have been the subject of much research. The subject is not peculiar to the production of oil and gas, as many investigators have studied the nature of this movement and its relationship to the problems of other industries. Darcyl conducted a series of experiments relating to the percolation of water through filter beds. King2 carried on an extensive series of laboratory experiments with the object of formulating some conception of the rate of movement of water through soils and sand strata in the drainage of surface water into underground channels and subsequent recovery of this water through wells drilled into the source beds for irrigation purposes. Slichter3 undertook a study of the same problem from a mathematical standpoint, and more recently Furnas4 has investigated the flow of gases through beds of broken solids with particular reference to blast-furnace operation. With specific reference to gas production, Muskat and Botset5 of the Gulf Research Laboratory undertook an experimental study to establish quantitatively the characteristics of and laws governing the flow of gases through consolidated and unconsolidated porous materials of fine texture with a view of predicting the performance of gas in an underground reservoir. There seems to be a general agreement that many of the relationships between the numerousfactors influencing the flow of fluids through porous materials are far too complicated to be attacked by analytical methods based upon a knowledge of hydrodynamics. For gases, the laws of

Jan 1, 1932