Search Documents

By J. W. Borough

THE electrical conductivity of pure copper is markedly decreased by small amounts of impurity in solution. The magnitude of this effect has been very carefully determined by numerous investigators who studied a wide variety of impurity elements. Much of this work is summarized in an excellent review by Pawlek and Reichel.' The case of zinc impurity in copper is an exception to the above in that there has been no well-documented study of the effect using high-purity starting materials. The values for the effect of zinc on conductivity, which are usually taken from unpublished work by Skowronki, indicate that zinc in low concentration has no effect whatever in lowering the conductivity of pure copper. This effect, if true, is unusual since it is generally known that even in lowest concentration, impurities exert an effect on conductivity which is proportional to the amount dissolved. It is more reasonable to suspect that in the original work on the effect of zinc some of the zinc was oxidized out of solution during specimen preparation. The following experi- and calculated d-spacings based on the unit cell dimensions of Baenziger et al. Since the single crystal studies of Baenziger et al. were limited to (hk0) and (hk 1) data, it was not possible to Compare all the intensities of the powder and single crystal patterns. However, the strongest reflections of both studies, the (321) reflection, agree very well when the appropriate multiplicity factor is used. Good agreement was also found in a number of other reflections of lesser intensity. Despite the precautions taken in annealing the U6Fe powder, an appreciable amount of UO, was detected in the powder pattern after heat treatment. The powder pattern reported by Groganoand Clews is given in Table I. Except for the 3.15A line, which is the strongest line of UO,, their pattern, as far as it goes, compares favoEably with the data from this study. Gordon and Kaufmann have reported a diffraction powder pattern purported to be U, Fe but it bears very little resemblance to the patterns of Table I. ments were carried out to redetermine the effect of zinc on conductivity using high-purity starting materials and processing conditions capable of producing oxygen-free alloys. Materials used in the experiment were ASR 99.999 pct Cu and Cumingo 99.999 pct Zn. Four 1 lb melts were prepared with identical procedure in argon atmosphere with crucibles made from Speer No. 580 graphite. The compositions were 0.0, 0.1, 0.3 and 1.0 pct Zn. Standard No. 14 wire (0.064 in. diam) was made from these melts as follows. The 1 pct Zn sample was first reduced 94 pct by cold swaging with five annealing treatments of 800o for 10 min in hydrogen between swagings, and then reduced 94 pct to the

Jan 1, 1962

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By C. Gatlin, M. E. Chenevert

The effects of bedding plane orientation on the elastic constants and the yield strengths of three laminated rocks (one sandstone and two shales) and one isotropic rock (a limestone) were studied. The directional dependence of the elastic properties of these rocks was experimentally evaluated using a triaxial compression cell and auxiliary stress-strain measuring equipment. Symmetry of Poisson's ratios within the bedding plane suggested that horizontal isotropy exists, but the bedding planes do give rise to an appreciable difference between properties in the horizontal and vertical directions. For the three bedded rocks studied, Young's modulus was lower normal to bedding than along bedding. Yield strengths were determined at confining pressures from 0 to 12,000 psi in a triaxial compression cell. The rocks studied showed strength reductions as high as 40 per cent when the test specimen was oriented at 20°-30° to the bedding planes. The mechanical behavior of these rocks suggested that the rock properties of shear strength and/or coefficient of internal friction can vary with direction, depending on the particular rock tested. Tensile strengths were also measured and found to be lowest when failure occurred along bedding. This work shows that bedded formations exhibit sizable directional variations in both their elastic constants and yield strengths. It is suggested that these variations may be accounted for by using the "elastic laminate" model and the "variable coefficients" failure model. INTRODUCTION The nature of rock deformation at elevated pressures has been studied by many workers; papers by Handin,l,2 and Robinson3 illustrate the present state of knowledge. Most investigators have either chosen rocks which were as isotropic as possible (in order to avoid complications of data interpretation and analysis) or they have oriented their samples so that the effects of anisotropies (such as bedding planes) have been avoided. Of the studies performed, few were concerned specifically with mechanical anisotrop-ies. Griggs4 has presented limited data for specimens cut parallel, normal, and 45° to the bedding plane; he relates the strength anisotropy observed to the fabric (bedding) anisotropy. His tests were primarily concerned with large deformations (20 per cent strain); thus, no directional values of the elastic constants were reported. Handin has reported the results of similar experiments. Bott5has discussed rock strength anisotropies due to faults, cleavage, or bedding. He was concerned primari ly with determining the shear stress on such planes and did not mention the effect of friction. Jaeger6 later generalized Bott's work by taking friction into account and presented a limited theory for the failure of rocks having a "single plane of weakness", and also for rocks having a constant coefficient of friction, and a shear strength which varies with bedding plane orientation. Donath and Cohen,7 and Donathg have evaluated rock strengths from shale and slate specimens cut normal and parallel to bedding. A dependence of cohesive strength (7,) on the specimen orientation was also shown. Adler9 has also studied this problem and lists similar results. He assumes that all bedded rocks behave according to Jaeger's single-plane-of-weakness theory. Kalinin and Belorussov10 list results for strength tests parallel and perpendicular to bedding and use this information as a basis for hole deviation analysis. From the literature it is apparent that sedimentary rocks have been tested under widely varying conditions of stress; however, the assumption of isotropy is generally, but not always, made. Since geologic sedimentation often deposits sediments in very definite lavers.,. it seems that more svstema tic attention should be given to the possible effects of this natural bedding. Bedding, as used here, refers to visible regularities of grain size or orientation resulting from depositional processes. The mechanical strength anisotropies, which bedding may present, is not the only anisotronic property to be considered, since the elastic

Jan 1, 1966

By F. F. Craig

Many full-scale waterflooding operations are preceded by pilot floods, one purpose of which is to provide an estimate of recoverable oil. A laboratory model study was made to determine the influence of the producing wells' effective productivity on the oil recovery efficiency of single five-spot pilots, as well as single injection well pilot floods. The effective productivity is indicated by the value of Condition Ratio, defined as the actual well productivity to that of on undamaged and non-stimulated, normal-sized well in the same formation. The effects of initial gas satrcration and mubility ratio on recovery eficiency were also investigated in this model study. Model test results skowed that at favorable mobiliry ratios, a five-spot pilot flood can provide a direct quantitative estimate of the recoverable oil in the pilot area. If the pilot producer's Candition Ratio is 2.2 or more, upwards of 90 per cent of the recoverable oil in the pilot area is recovered from the inside producer, regqrdless of the mobility ratio or initial gas saturation. This Condition Ratio can be achieved with preyent fracturing techniques. Model studies also showed that over the range of imposed injection pressure differences and regional pressure gradients normally encountered in field operations, there was no effect on the recovery efficiency of a five-spot pilot waterflood. Model studies of single injection well pilot waterfloods showed that with no initial gas saturation, the total oil recovery at the offset producing wells can indicate the oil recovery possible by full-scale waterflooding. It is essential that the Condition Ratios of the offset wells be above 1.4. If an initial gas saturation exists prior to water injection, the recoverable oil cannot be directly evaluated by a single injection well pilot flood. However, the production per formance of such a flood can be used to provide information on volumetric sweep efficiency. INTRODUCTION Oil reservoirs are conlplex structures and cannot always be fully studied in the laboratory. Therefore, many operators consider it prudent to evaluate a waterflood prospect by means of a pilot flood. Pilot waterfloods generally involve one of two well arrangements: a single five-spot pilot waterflood, involving four injectors and an internal pilot producing well; and a single injection well pilot flood (sometimes called an inverted five-spot pilot) having one injector and four sur- rounding pilot producers. Some pilot floods are composed of multiple five-spot pilot patterns. To yield information applicable to field-wide performance, the pilot must be located in a representative portion of the reservoir. Pilot floods generally are conducted for one or more of the following reasons: (1) to determine whether water could be injected at desirably high rates, (2) to determine whether an oil bank or zone of increased oil saturation is formed by water injection, and (3) to estimate the oil recovery by waterflooding. Many of the early pilot water-floods were conducted for only the first two reasons. As soon as a buzz in oil production was obtained in the pilot, water injection was initiated throughout the entire lease or field. A number ot laboratory studies have been directed toward determining conditions under which a pilot flood could yield a quantitative estimate of the oil recovery possible by full-scale pattern flooding. One of the early studies of single five-spot pilot flooding' showed that well damage to the inside pilot producer could reduce the total amount of oil recovered. In a study of the single injection well pilot flood pattern,' the results indicated that if the model boundaries were no closer than a half-well spacing beyond the pilot pattern, the pilot performance in the laboratory is unaffected by these boundaries. In another study,? he effect of initial gas saturation and mobility ratio on the ratio of production to injection rate for various groupings of five-spot patterns was defined by mathematical and analog methods. In a study4 involving both potentiometric and flow model experiments at a mobiliry ratio of unity, four different pilot patterns were studied. These included a single five-spot, a single injection well pilot, a cluster of four single injection well pilots and six inverted five-spots. In this study the ratio of well diameter to the distance between injection and producing wells was held constant at 1:1000. The effect of the 7 ratio-—the ratio of the pressure drawdown at the producing wells to the pressure build-up at the injection wells on the pilot performance-was studied. The values of 7 ratio ranged from 0 to 0.34. Results showed that both the total oil recovery and the total fluid production from the pilot relative to the cumulative injection increased with increasing values of the 7 ratio. The effect of both the ratio of injection to producing rates and mobility ratio on the oil recovery performance of a liquid-saturated single five-spot pilot flood was studied in a series of flow model tests.5 Rate ratios ranged from one to four, and mobility rates ranged from 0.1 to 10. Resulls of these tests showed that at low rate ratios, the pilot producers may recover up to four times the recover-

Jan 1, 1966

By J. M. Oblak, W. A. Owczarski

A cellular appearing recrystallization product formed by annealing a cold-worked nickel-base super-alloy at 1800°F has been studied by electron nzicroscopy. Prior to deformation, an equilibrium micro-structure of fcc matrix y and cuboidal ,,', Ni (Al, Ti), precipitates of CuzAu structure had been established by an age at 1825°F. The strain-free recrystallization cells consist of very large rodular y' particles in a y matrix. They precipitate is oriented and coherent both before and after recrystallization. The results showed that y' coarsening accompanies recrystallization at 1800°F. However, it does so as a secondary effect and does not necessarily take place at lower temperatures. The structural similarity of this reaction to cellular precipitation in other systems indicates that lattice strain may also play a significant role during some cellular precipitation reactions. THERE have been numerous microstructural investigations of recrystallization in single-phase materials but two-phase systems have received much less attention. The second phase can either remain inert or be altered along with the matrix during recrystallization. If the second phase is an oxidelm3 or a relatively inert pre~ipitate,~, recrystallization is retarded when the interparticle spacing is less than 1 p. Prior to the onset of recrystallization, these materials show a well-polygonized substructure with the subgrain size limited by the interparticle spacing. Since recrystallization by the motion of preexisting grain boundaries6 is not observed, retardation has been related to particle pinning of the subboundaries. This pinning prevents coalescence' or growth8 of subgrains to a critical size (formation of a high-angle boundary) necessary to initiate recrystallization. In a material such as a nickel-base superalloy both y matrix and y' precipitate are altered by the recrystallization reaction. Haessner et al.' studied the recrystallization of a cold-rolled Ni-Cr-A1 alloy by electron microscopy. The material was initially cold-rolled in the supersaturated condition. upon annealing at 750°C, immediate precipitation of 7'occurred. Presence of this 7' greatly retarded the onset of recrystallization which eventually took place by the development of randomly oriented, strain-free grains. The original •/ was dissolved at the recrystallization interface and reprecipitated as oriented, coherent par-tiles in the new grain. Recrystallization caused a refinement of .)' particle size. Recently ~hillips'' investigated recrystallization of Ni-12.7 at. pct Al. Reduction by cold rolling presumably elongated the p' precipitate into lamellae that remained coherent with the matrix. After recrystallization at 600" to 750°C, there was no unusual change in y' particle size al- though there was a tendency toward clustering along the prior rolling direction at 750°C. Above 750°C, the recrystallized grains were generally free of precipitate. Studies in the somewhat analogous Cu-3.23 wt pct CO" and Cu-2 wt pct'2 systems demonstrated that the coherent cobalt-rich fcc precipitate in these alloys obstructed softening, initiation, and completion of recrystallization. The precipitates were deformed into lam~llae during rolling and those of diameter less than 250A remained coherent. Recrystallization took place by the growth of new grains into the recovered or poly-gonized material. In the first study," both matrix and precipitate reoriented in the same manner upon passage of the recrystallization interface. There was no change in particle size or morphology. Tanner and ~ervi,~ on the other hand, observed that motion of the recrystallization fronts was strongly hindered by the pinning action of coherent precipitates in the deformed material. Particles in contact with a pinned boundary coarsened and coalesced leaving a denuded zone in the unrecrystallized region. When the number of pinning points was sufficiently reduced by coalescence, the boundary swept past these particles and through the denuded zone. The authors1' considered this as a variation of discontinuous precipitation with both chemical driving force and deformation strain energy contributing to recrystallization. Preliminary observations by the present authors had revealed that recrystallization in Udimet 700, a nickel-base superalloy, occurred in an entirely different manner. Optical metallography showed that the recrystallized product formed as cellular colonies containing coarse y' particles elongated in the direction of cell growth. In this investigation the structural features of this reaction were investigated by transmission electron microscopy. EXPERIMENTAL PROCEDURE As-received I$-in. rounds of Udimet 700* were (wtpct) 18.4 15.2 4.95 4.42 3.43 0.06 0.031 0.14 Bal. solution-annealed for 4 hr at 2150" and then fast air-cooled. An initial y-~' structure was established by a 4-hr age at 1825°F followed by a fast air,cool. Essentially the equilibrium volume fraction of ?' at 1825°F is precipitated within 4 hr. Microstructural examination showed no measurable increase in the amount of precipitate after longer aging times. Deformation consisted of swaging to 52 pct RA with 6 pct reduction per pass at room temperature. To reduce the precipitation potential to a negligible amount, recrystallization anneals were conducted at 1800"~ (982"~). Microstructures were investigated by optical and transmission electron microscopy. To prepare foils for electron microscopy, the material was first sliced into 30-mil slabs parallel to the swaging direction. Discs were dimpled and electrolytically cut from

Jan 1, 1969

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By Robert M. Keeney, Jay Lonergan

The electric smelting of manganese ore and the production of ferro-manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 11/4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese orc in the electric furnace during the war and in 1920 are listed in Table 1. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferromanganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the price of ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 1, 1922

By Jay Lonergan, Robert M. Keeney

The electric smelting of manganese ore and the production of ferro-manganese did not exist as an industry, in the United States or elsewhere, previous to the outbreak of war in 1914. Ferromanganese had been produced, electrically, during times of high prices by two companies at Niagara Falls and by several European companies, but the production was spasmodic, and none was electrically produced when ferromanganese sold at from $35 to $40 per ton. Thus the electric smelting of manganese ore must be considered as a development caused by the high prices prevailing during the years 1916, 1917 and 1918, and the necessity of smelting domestic ore in order to fill the ferromanganese requirements of the steel industry of the United States, which increased from 189,088 tons in 1914 to 356,356 tons in 1918. The electric furnace is well adapted to smelting domestic ore because it can be located in small units near the source of ore supply. In 1918, the ferromanganese production of the United States was 333,027 tons, of which about 7 per cent., or 23,000 tons, was produced in the electric furnace. The electric furnace not only assisted materially in the development of a domestic-ore supply but made a considerable saving of coke, as it requires about 11/4 tons of bituminous or lignite coal per ton of ferromanganese compared with a blast-furnace consumption of 2.9 tons of coke per ton of ferromanganese. Some of the plants in the United States that smelted manganese orc in the electric furnace during the war and in 1920 are listed in Table 1. From early in 1919 to about February, 1920, little ferromanganese was produced in the electric furnace. During this period the price of ferromanganese (78 to 82 per cent. manganese) was about $100 per ton. During the first half of 1920, several plants resumed operation when the price of ferromanganese (76 to 80 per cent. grade) gradually increased to $200 per ton, delivered.

Jan 1, 1922

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year's symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. 'It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved') and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

By James Terry Duce

The symposium on production for the year 1941 contains few papers on the foreign situation. Rigid censorship prevails in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even truer than in the last war, owing to greater mechanization of armies. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to AutHORs In order to facilitate interpretation of the data in this chapter, we print the fol-lowing excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir.. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1942

By Winthrop P. Haynes

The symposium on production for the year 1943 contains few papers on the foreign situation. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. A noteworthy feature of the reports on Texas this year is the map on page 469, which shows the districts covered by the statistics. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author's best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determina-tion. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are suficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on ''Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can be calculated by those interested from the figures given. In classifying wells as to producing methods, enter all wells that are not "flowing" in the column headed "Artificial Lift." If possible, add footnotes to indicate whether the lift is "pumping," "gas lift" or "air lift."

Jan 1, 1944

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

THERE has been a lot of talk about the shortage of engineers and we have done our share of it; but recently we heard a spot radio commercial-between broadcasts-urging high school seniors to study engineering. We think this is going too far. Engineering is an exacting profession requiring the highest personal qualifications. Publicity for the purpose of interesting capable young people in choosing courses in engineering should emphasize qualification. The opportunities for a career in a great constructive profession which is the basis of our high standard of living should be properly evaluated. Although there is a need for more engineers today, nobody knows what the employment potential is going to be four years hence. The profession may do itself a grave disservice by attempting mass recruitment in the face of an unpredictable national economy. The mining and metals industries are in a special position as fewer engineers are needed in these fields. Only 10 pct of all engineers are mining and metallurgical engineers. Today's shortage is not so much in recent graduates, but in trained practicing engineers. The shortage has served the profession to good effect because it directed the talents of engineers into more productive channels. In some areas high school graduates have been put into routine jobs such as, surveying. If there is one thing the mining profession does not want, it is an oversupply of graduates which would relegate college men to years of work and discouragement in routine jobs. The public has a clear cut picture of the legal and medical professions and thus the respect knowledge imparts. But the engineer is variously thought of as a man who pulls the throttle lever on a locomotive, tends a furnace, or builds a bridge. The term engineer is too loosely used. For instance we have heard of "crowd engineers" and "exterminating engineers." In some unions an engineer designation has been established to describe a person doing routine checking or other control job. We do not disparage these positions but they are different from the work done by the man qualified by years of experience and study. Many of these so-called engineers are not engineers at all. The engineering profession has cooperated closely on a program of recruiting high school graduates for engineering study. It should start a cooperative public relations program to enlighten the public on the accomplishments and work of engineers. This type of publicity need not be of the bombastic type. It can be educational and dignified. Radio, television, and the periodicals can be used to convey information. It is time that laymen and interested young people learn to make a distinction between the true engineer and the technician. Such a program would instruct parents and high school students and thereby interest the right type of people in the engineering profession. The Centennial of Engineering sponsored by the American Society of Civil Engineers is a step in the direction of instructive public relations. This fine start should not be allowed to remain as a one pass venture. The engineering profession as a whole should follow this exposition with a sustained, well directed effort to inform the public of the engineer's work and the possibilities it holds for a constructive career.

Jan 1, 1952

Discussion of the paper of DORSET A. LYON and ROBERT M. KEENEY, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin. No. 92, August, 1914, pp. 1791 to 1800. LAWRENCE ADDICKS, Chrome, N. J.-I read this paper for the first time this afternoon, and it is really worthy of a much more careful reply than I can make with such a short time to consider it, but I just want to say that I differ with Dr. Lyon in his premises and conception of what happens in a refining furnace. He cites steel as an instance where the production of special grades justifies the high cost of power in an electric furnace, and goes on to say the same will be true in the case of copper, for the reason that you will get a better quality of product. I don't think you will get a higher grade of copper,. or a better conductivity, as I will explain in a moment. The cost of fuel in the Eastern plants is somewhere between 30c. and 40c. per ton of copper refined, and, if my memory serves me correctly, in an open-hearth steel furnace it is something like $1.25, so it is evident that steel could be handled to better advantage than copper on the basis of fuel. Now, taking the Great Falls plant to compare with is not quite fair, because that plant operates under peculiar conditions. The furnaces are relatively small; the coal is very bad and is very high in sulphur. No one would think of using a coal with 3.6 per cent. sulphur were anything better available. Due to these conditions, the amount of slag is inordinate, it being quoted as 3.5 per cent., and it is necessary to use lime, as there is a tendency to have troubles from arsenic owing to the very high current density used. I think he has taken about as hard a case as he could pick out. Now as to the conductivity of copper, my own idea about the reason that melted copper does not give as high a conductivity as pieces drawn directly from a cathode, or native copper, is that in the latter case the impurities are present as a mechanical mixture, while after melting they are chemically combined with the copper, which is a very different condition. Further, it is necessary to take the sample from a relatively smooth and consequently pure part of the cathode, as otherwise it would not draw. The same with the mass of copper; you pick out a good solid part of the copper, which is not representative. In fact, the refiners have all found they could not take fair samples of cathodes for a chemical analysis. It is always customary to use wire-bar copper -for the purpose of sampling, and the impurities are several times as great as shown by samples taken from .the cathodes. I think if we examine all of the examples he has given of cases where copper is higher in conductivity, it will fit with that explanation. For example, the Elmore process is a direct electrolytic deposit. Incidentally, at the present time there are a number of ex-

Jan 12, 1914

By A. D. Dorenfeld

Factorial design is a mathematical method of drawing valid conclusions from a series of tests made in a predetermined pattern. It is applied to flotation ore testing using, in this case, five variables, each varied twice, requiring a total of 32 tests. Representative conclusions are checked by repeat testing. THE factorial design method of testing is particu-J- larly applicable to mill-scale plant tests because 1—the conclusions take into consideration all variabilities of the plant, 2—there are no subjective guesses as to the conclusions, 3—the number of tests necessary to check large numbers of variables are at a minimum, and 4—interactions between variables can be discerned. It is equally applicable to laboratory testing because once the variables to be investigated have been decided upon, as well as the number of levels for each variable, a well-trained assistant can run the tests, since the test work follows a predetermined mathematical pattern, leaving the conclusions to be found by the person in charge. The conclusion takes into consideration all errors of the tests. To illustrate the use of factorial design, a sample of copper porphyry ore was tested, the copper content of the batches not being uniform. Five variables were investigated, each at two levels, requiring only 32 tests. After suitable arithmetical analysis, conclusions for copper recovery and concentrate grade are arrived at. Four cases of these conclusions are checked by repeat testing. Testing Methods Reproducibility of flotation tests varies widely, depending on the experimenter, the process, the equipment, and probably a host of unknown and perhaps interacting variables. If the reproducibility of tests is good, let us say to 0.2 pct recovery of a certain metal, and the minimum difference between tests upon the variation of the interested variables is, say 1 pct, then simple averaging and inspection is ample in interpreting results. However, often such a happy situation is not the case. This is particularly true in mill-scale operations where the ores are variable, and a host of minor operating fluctuations common to most milling, and familiar to all mill operators, is the normal state of affairs. Yet, mill scale tests are run, the results averaged, and conclusions drawn therefrom. The trustworthiness of such results should be measured by comparison to the experimental error—the measure of the degree of reproducibility of the results. This comparison is a test of significance. Thus, if daily results of recoveries average 80.0 pct, and a spread of 78.0 pct to 82.0 pct, is recorded, then, clearly, on changing mill operations, an 81 pct recovery cannot be construed as significant by using averages, since it is well within the previous test limits. By using rigorous statistical tests of significance, conclusions arrived at by inspection or simple averaging may be shown to be based on inadequate evidence or even wrong. In any event, a plant super-

Jan 1, 1952

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948