Search Documents

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (— 325-mesh) sand assaying 95.5 per cent SiO2, and a very he (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fractioh was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1947

By B. G. Bunting, D. L. Abata, J. Robb, J. H. Johnson

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during mining operations. The explosives included two semi-gelatin dynamites, three slurry explosives, and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and toxic gases produced by the detonation were trapped at the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/1bm): NO, 0.0100-0.035; N02, 0.003-0.019; CO, 0.08-0.30; SO2, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1983

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth's crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth's surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By E. A. Gulbransen, K. F. Andrew

The gas-metal reactions of zirconium are very interesting. The metal is extremely stable at room temperature to reactions with the several gases present in air and the metal will stay bright indefinitely. However, at temperatures of several hundred degrees higher the metal reacts readily with oxygen, nitrogen and hydrogen. This behavior, in addition to the fact that zirconium is one of the higher melting point metals which might have high temperature applications under the proper conditions, resulted in the work reported in this communication. There are several factors which indicate that zirconium might have good oxidation resistance at elevated temperatures. These are: (1) the high melting point of approximately 1860°C, (2) the high melting point of the oxide of approximately 2675°C, (3) the high degree of thermodynamic stability of the oxide to chemical reaction and the low decomposition pressure of the oxide and (4) the possible formation of a continuous oxide film since the volume ratio of oxide to metal is greater than unity. The unfavorable factors are: (1) the metal reacts to form nitrides, hydrides and carbides, (2) the oxide is soluble at elevated temperatures in the metal and (3) the oxide ZrO2 undergoes crystal structure transformations at high temperature. The oxidation resistance of this metal is not only a question of the rate of film formation but is complicated by the fact that the oxide and other reaction products dissolve in the metal which in turn will affect the physical and mechanical properties of the metal. The protection of the metal to nitride formation must be considered separately from the oxide problem. One unfavorable factor is that the volume ratio of the nitride to the metal is about unity. This indicates that a discontinuous film might be formed. This paper will present measurements on the rates of reaction of the metal with O2, H2 and N2 over a wide temperature and pressure range. The reaction in high vacuum and the stability of the several compounds formed will be presented. The results are correlated with fundamental rate theory and with the physical and chemical structure of the metal and film. Literature Although many papers have been published on the chemical reactions of zirconium with various gases, comparatively few are concerned with the protective nature of the metal and its reactions at normal pressures. The studies in the pressure range below 0.01 mm of Hg gas pressure are largely of interest in the nature of the adsorption of gases by hot filaments in high vacuum apparatus. The reactions of zirconium in this pressure range have been reviewed by Fast8 and by RaynOr.27 In spite of certain differences of opinion as to the maximum adsorption temperatures for various gases, the low pressure range is qualitatively understood. Some of these papers will be mentioned briefly here. 1. LOW PRESSURE Ehrke and Slack' find that oxygen reacts above 885°C and hydrogen above 760°C. Nitrogen does not react up to a temperature of 1527°C. Fast9 on the other hand observes that oxygen is absorbed above 700°C and nitrogen at temperatures exceeding 1000°C. Hydrogen is absorbed from 300" to 400°C and liberated between 500" and 800°C. It is readsorbed at 862°C and released above 862°C. Hukagawa and Nambo22 find a rather complicated picture for the absorption of oxygen. A rapid initial absorption is found between 180" to 230°C. Further oxygen is not taken up until a temperature of 450°C is reached. The optimum temperature for complete absorption is 650" to 700°C. Nitrogen is found to be completely adsorbed at 600°C. However some of the gas is evolved at higher temperatures. Their data on the absorption of hydrogen indicate some of the gas is removed at 550°C. Guldner and Wooten17 in a study of the low pressure reactions of zirconium with various gases observed that the reaction with oxygen occurs at temperatures above 400°C and that the oxide is formed. The reactions with carbon monoxide and carbon dioxide occur rapidly at temperatures of about 800°C with the oxide and carbide being formed. Zirconium reacts at temperatures of 400°C slowly and at 800°C rapidly to form the nitride and with hydrogen and water at 300°C to form the hydride and a mixture of the oxide and hydride respectively. 2. NORMAL PRESSURE DeBoer and Fast3 in a study of the electrolysis of oxygen in zirconium find that the metal absorbs up to 40 at. pct of oxygen without forming a new phase. The solubility of nitrogen in the lattice has been studied by de Boer and Fast4 and Fast10 and is found to be considerable. At higher temperatures the oxide dissolves in the lattice at an appreciable rate according to Fast10 and the zirconium surface becomes active. De Boer and Fast4 and Hägg18 have studied the solubility of hydrogen and find that at room temperature the solubility corresponds to ZrH1.95 Desorption occurs on lowering the pressure. Hydrogen is stated to be more soluble in the ß-form and the

Jan 1, 1950

By THEODORE DWIGHT

Members of the Institute have already received a special pamphlet descriptive of the United Engineering Society building, and wilt doubtless be interested in the progress that has been made up to date-February 24th-in erecting this home for the engineering profession. The old buildings on lots Nos. 25 to 33 W. 39th St., New York, were,' removed many months ago, but final contracts for the new, building were not let until the summer of 1905. The size of the building is 115 ft. on 39th Street, and 88 ft. in, depth; the height from, the sidewalk to the top of the parapet is 220 feet. The cubic contents of the building from the. bottom of the basement floor, to the top of the roof, including the pent houses, is 2,290,000 cubic feet. The number of light's, in the building will be between 4,000 and 4,500. The air supply for Auditorium and Lecture. Halls will amount to nearly 10.0,000 cu. ft, per minute, and the exhaust. to 90,000 cu. ft. per minute. In excavating for cellar and foundations, the average depth where good rock was. found was 37 ft.-it varied, however,: from 27 to 65 ft., due to an old water-course having run through the center of the lot; this condition, and the presence of soft rock, which rapidly disintegrated when exposed to air and water, made the foundation-work very difficult. As two of the column-footings of the building have to sustain a weight of 3,000,000 11) each, the most substantial foundations are necessary; 13,000 cu. yd. of earth were excavated for the foundation and basement; and 1,600 cu. yd. of concrete were necessary, to build up the footings. In the completed building there will be about 3,500,000 bricks. Owing to the number of auditoriums, and their location, and the placing of the library on the top floor; where allowance will have to be made for the enormous weight of 300,000 books, the structural steel work has been unusually complicated in this building. For instance, over the auditorium there are two 60-ton plate-girders, made up

Mar 1, 1906

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By H. Tabachnick, N. Hedley

The extraction of gold and silver from ores with alkaline cyanide solutions is well known. Cyanide solutions are also good solvents for many base metal minerals, particularly most of the copper minerals. Leaver and Woolf,1 who determined the solubilities of copper minerals in 0.10 pct sodium cyanide solution, showed that malachite, cuprite, chalcocite, and bornite are readily soluble in cyanide; least soluble are chalcopyrite and chrysocolla. The Mining Chemicals Laboratory of American Cyanamid Co. has studied the possibilities of using cyanide solutions for leaching base metals. In this article the authors present the results of their experiments with cyanide leaching to reduce the copper content of a zinc concentrate from 0.050 pct to the desired specification of less than 0.02 pct. Zinc Ore Sample: The sample of commercial zinc ore used in this investigation to produce zinc concentrates was ball mill feed ranging from 1/2 in. to fines. The ore was crushed to —10 mesh and riffled into 600-g charges for zinc flotation. Analysis revealed 4.54 pct Zn and 0.005 pct Cu. Examined microscopically, the ore consisted essentially of cream-colored sphalerite and carbonate gangue. It contained a small amount of pyrite, partly tarnished. The only copper mineral identified was chalcopyrite, mostly smaller than 20µ, some of which occurred as attachments on sphalerite. Flotation Procedure: Batches of zinc concentrates were made as required according to the following general procedure. A 600-g charge of —10 mesh ore was ground for 4 min at 60 pct solids in a laboratory steel rod mill. Screen sizing showed it to be all —35 mesh with 42 pct —200 mesh. The pulp was transferred to a Fagergren laboratory flotation machine, diluted to 25 pct solids and conditioned for 5 min with 0.6 lb per ton CuSO4, . -5H2O. It was then conditioned with 0.10 lb per ton Sodium Aerofloat promoter and floated for 5 min with pine oil as frother and creosote as froth stiff-ener. The pH during flotation was 8.5. A typical analysis of zinc concentrate subjected to leaching is 44.41 pct Zn and 0.051 pct Cu. The ratio of concentration was close to 10 to 1. Leaching Procedure: Aero Brand cyanide, technical calcium cyanide analyzing 49.5 pet NaCN equivalent, was used for all cyanide leaching tests. For each test three rougher concentrates floated as described were combined (total weight close to 180 g) and the water content adjusted to 150 ml. The percent solids in the pulp was thus 55. After a weighed amount of cyanide flakes had been added, the pulp was agitated on rolls for a given period, then filtered and washed. Filtrate and washed concentrate were assayed for copper content. The procedure for ammonia leaching was similar to the cyanide process. A series of tests was run in which the effects of ammonia as a solvent for copper in the zinc rougher concentrate were investigated. In each test 180 g of zinc rougher concentrate was leached with 150 ml of ammonia solution. Various strengths of ammonia and times of leaching were investigated. The results are shown in Table I. It is apparent that ammonia was a poor solvent for copper in the zinc concentrate; 60 min of agitation with a relatively strong NH:, solution extracted only 2 pct of the copper. CYANIDE LEACHING TESTS Effect of Solution Strength: The solvent effects of 0.125, 0.187, and 0.250 pct NaCN equivalent solutions were compared for leaching periods of 15 min. Residue and filtrate were assayed for copper content. The copper content of the filtrate plus wash was calculated back to the original volume of cyanide solution (150 ml). The effects of cyanide strength are given in Table II, It will be noted that 15 min leaching with 0.25 pct NaCN equivalent solution extracted 74.6 pct of the copper in the zinc concentrate. The leached product assayed 0.013 pct Cu, appreciably below the required specification of 0.020 pct. Effect of Leaching Time: Portions of zinc concentrate were leached with 0.25 pct NaCN equivalent

Jan 1, 1961

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.'-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962

AS we contemplate the bestowal of the John Fritz medal year after year on men of wide-world dis-tinction in the various fields of engineering, men who in one way or another have given impulse and direction to the progress of mankind, the question becomes inter-esting as to what manner of man was John Fritz and what were the qualities that singled out his name to be so conspicuously associated with the world's great scientific and industrial achievements. If, as Lowell said, it is the duty of the nation to pro-duce great men, our country surely rose to her oppor-tunity when she guided and guarded the career of John Fritz. Starting life as a blacksmith with no advantages of education, without influential friends or the favor-ing accidents of fortune, he advanced steadily in use-fulness, power and respect of his fellowmen until by common consent he occupied the first place in the domain of the steel industry of this, country. The numerous honorary scientific memberships conferred upon him in this country and abroad attest the esteem in which he is held by his fellow engineers. Twenty years after his retirement from active business at the age of seventy, he lived to enjoy, as few men have been permitted to do, the fame and the friendships which he had so amply earned. His sterner qualities of industry, integrity and sterling character were re-lieved by unfailing human sympathy, humor and spon-taneous good-will toward his fellowmen. To all who

Jan 3, 1928

By G. W. P. Rengstorff

In an effort to find an oxidation-resistant alloy of molybdenum, binary and ternary alloys containing aluminum, chromium, cobalt, iron, nickel, silicon, titanium, tungsten, vanadium, and zirconium were screened. Fourteen other alloying additions were also tested. Many of the alloys were more oxidation-resistant than molybdenum, but none were entirely satisfactory. MOLYBDENUM oxidizes extremely rapidly above 1450°F in air. At 1800°F, a loss of metal at the rate of 0.1 in. in 4 hr is typical. The high speed of this oxidation may be judged by comparison with the oxidation rate of 0.1 in. per year (0.00005 in. in 4 hr), sometimes taken as the maximum permissible oxidation rate at 1800°F for a satisfactory Fe-Cr-Ni alloy. Great strides have been made in the development of coatings and cladding to protect molybdenum from oxidizing atmospheres. These developments in surface protection will undoubtedly make it possible to take advantage of the excellent hot strength of molybdellum and its alloys in many new applications. Still, even the best coating can protect molybdenum only as long as the surface layer is unbroken. Research was undertaken to determine whether an alloy of molybdenum could be found which would resist oxidation. Such an alloy would not deteriorate suddenly when the protective surface layer was destroyed in a small area. In seeking an alloy of molybdenum to resist oxidation, the physical properties of molybdenum could not be sacrificed entirely. The development of an alloy with the desired resistance to oxidation was not achieved. The information obtained on the effect of a large number of elements on the oxidation of molybdenum is, however, of value in the development of coatings. Indeed, many of the alloys tested for oxidation resistance were already known to have poor mechanical properties but were tested to aid in the development of coatings. Oxidation of Molybdenum The rapid oxidation of molybdenum is usually attributed to the volatility of Moo,,. Gulbransen and Wysong have shown that molybdenum oxidizes very slowly up to 850°F, the temperature at which the oxide film begins to evaporate. Melting as well as evaporation of molybdenum oxides promotes the oxidation of molybdenum. MoO melts at 1465°F. MOO, the oxide which is believed to form at the metal-oxide interface, combines with MoO, to form a eutectic having a melting point of 1432°F.' The liquid oxide, even if nonvolatile, could cause poor resistance to oxidation by allowing easy transport of molybdenum and oxygen ions through the oxide. Actually, a sudden increase in the rate of oxidation of molybdenum at 1460°F has been observed to coincide with the appearance of a liquid phase. The formation of a volatile oxide is not unique with molybdenum. The problem is also encountered with vanadium, tungsten, and some of the Pt-Pd group of metals. Vanadium not only forms the volatile V2O3 but, like molybdenum, forms a liquid oxide coating. Few attempts have been made, however, to prevent the rapid oxidation of these metals by alloying. Oxidation of Molybdenum Alloys At the beginning of this work, very little was known of the oxidation resistance of molybdenum alloys. It was known that molybdenum disilicide (with 37 pct Si) has extremely good oxidation resistance,' but this compound is so brittle that it has few uses. It is an effective protective coating for molybdenum when allowance can be made for its brittleness. Chromium was known to retard the oxidation of molybdenum,' but at least 50 pct Cr was necessary to have an appreciable effect. Other, unpublished, reports show that a few other alloys have been given preliminary tests, but the results have not been promising." Choice of Alloys to be Investigated An alloying element might be expected to protect molybdenum in either of two ways: Its oxide might combine with molybdenum oxide to form a stable, nonvolatile complex oxide (a molybdate); or the oxide of the alloying element might form in preference to molybdenum oxide, developing an impervious layer which would prevent the formation of a volatile molybdenum oxide. The knowledge available about the formation of molybdates was meager. Therefore, the initial study was made on alloys of molybdenum with elements having especially stable oxides. On this basis, binary and ternary alloys containing the following six elements were investigated: aluminum, chromium, titanium, zirconium, silicon, and vanadium. Nickel was also added as an alloying element. Although it does not form a more stable oxide than molybdenum, it does impart some oxidation resistance to copper and iron. Its inclusion in the study was fortunate because its alloys proved to be the most promising of those first tested. Apparently nickel formed a stable molybdate. Because nickel was effective in reducing the oxidation rate of molybdenum, the elements iron, cobalt, and tungsten were added to the list. The ten alloying elements mentioned form ten binary and 45 ternary alloying systems with molybdenum. A series of alloys was tested in each of these systems. In addition, at least one test was made on the effect of each of the following alloying elements:

Jan 1, 1957

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By Willis R. Battles, William F. Cerini, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By Fred Bond

THERE is acute need for a method that will measure the size distribution of finely di-vided materials, particularly when the par-ticle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the sam-ples produced are adequate for a consider-able amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essen-tially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the set-tling rate. The balance appears to be in-herently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have re-stricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investiga-tion might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribu-tion determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used, in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared, early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could he accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the dis-tribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By P. Nyul, S. Caplan, M. F. Lamorte, T. Gonda

Therrnal resistance is measured on GaAs laser diodes in the temperature range 77" to 300°K. These data show that typically the thermal resistance increases fifteen times from 77 to 300°K. The increase is attributed to the decrease in thermal conductivity of Gds. Nornzalized thermal-resistance experimental and calculated from published thermal-conductivity data) values are compared and good agreement shown. In many practical applications, it is desirable to obtain high average power output from laser diodes. Average power output is determined in large measure by the external efficiency and thermal resistance of the diode.'-3 The average input power with which a laser diode may be pumped is dependent on the thermal resistance. Thermal resistance has been studied over the temperature range from 77" to 300°K which is usually of interest in practical applications. This correspondence presents data on thermal resistance for GaAs laser diodes and compares them to values calculated from thermal-conductivity data. Junction heating arises from three distinct components: 1) joule heating, 2) nonradiative recombinations, and 3) reabsorption of radiation. In high-threshold lasers, joule heating predominates.4 Typically, the nonradiative recombination is not negligible and contributes significantly to junction heating. The loss caused by reabsorption may be of the order of the joule-heating loss.' The fabrication and the geometry of laser diodes have been described in other publications.5 The data presented were obtained from diodes which were fabricated from the same region of a wafer to minimize differences. Fig. 1 shows four types of heat sinks employed in this study. In types 1 and 2, the laser cavities are alloyed; pressure contacts are employed in types 3 and 4, and indium is plated on the inside faces to improve the intimacy of contact between the diode and the heat sink. The thermal resistance R is defined by the following relationship: where AT is the junction-temperature rise above the heat-sink temperature for the diode power dissipation Pd. For measurement of thermal resistance, a direct current is passed through the junction, in the range from 1 to 50 pct of threshold. The diode is placed in the laser mode by superimposing a current pulse of low-duty cycle on the direct current.3 Junction-temperature rise is obtained from the time-resolved laser spectrum at the leading edge of the current pulse.' Typically, the laser line shift is 2.5A per OK. The resolution employed in these experiments is 0.5A; therefore, the accuracy in the temperature measurement is 0.2K. Typically, the temperature rise is 2" to 20°K. The power dissipation is the difference between the dc power input, and the radiation power exiting the diode. The measurement accuracy is less than 1

Jan 1, 1968