Search Documents

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By John Lohrenz

Consider an investor who, knowing future costs and revenues, can choose how rapidly to produce from a given mineral source. If the investor elects to make that choice to maximize present value of future profits, how do policies affect the choice? Various alternative policies are examined. Some, such as higher royalty rates, lead to slower production rates than would otherwise obtain. Clearly, the chosen rates of production are policy-dependent. One is wisely counseled to consider how mineral policies affect the rate of production from given sources when analyzing current and alternative policies.

Jan 1, 1982

Aamot, Olav Crone, Chem. Engr., Elektrokemisk Raadhusgt..23, Oslo. Norway. '29 Abadilla, Quirico A., Dir., Bureau of Mines Manila, P. I. '3S Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L.. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '2S Abel, Walter D., Div. of Corporations Los Angeles, Calif. '32 Abele, Louis T., U. S. Corps of Engrs 7211 Glen Oak Ave., Baltimore. Md. '31 Abel], Leo M., Research Met., Mount Morgan Ltd Mount Morgan, Queens.. Australia. '31 Abenius, Hakan V c/o Falu Gruva, Falun, Sweden. '37 Abernathy, G. E., Geol., Kansas State Geol. Survey Pittsburg, Kan. 3S Aborn. Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abrams, Charles Jackson 1624 17th St., Denver, Colo. '3 t. Abstein. Henry T., Engr. & Mgr., Profile-Tamarack Mines CoYellow Pine, Idaho. '27 Acker, E. O'C., Met L28 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Assoc. Prof. of Met., Purdue Univ Lafayette, Ind. '35 Ackerman, E. Dumont, Sub-Surface Geol., Temblador Camp, Standard Oil Co. of Venezuela, Caripito, Venezuela. '3S Ackerman, George F.,. Div. Foreman. The Fresnillo Co Fresnillo, Zac., Mexico. '36 Adami, A. F., V.P. & Prof. of Min. Engrg., Montana School of Mines Butte, Mont. '19 Adami, Charles J., Min. Engr 99 S. Downing St., Denver. Colo. '12 Adams, Army, Cons. Engr 714 W. Main St., Grass Valley, Calif. .'37 Adams, Clyde B.. Geol.. Socony-Vacuum Oil Co., Inc 26 Broadway, New York, N. Y. '39 Adams, Ernest C., 6th Engrs Fort MacIntosh, Laredo, Tex. '35 Adams, F. J., Gen'l Agent, Gulf Production & Pipe Line Cos Fort Worth, 'lox. '29 Adams, F. S., Supt., Power Dept., Anaconda Copper Min. CoAnaconda, Mont. '37 ADAMS. FRANK DAWSON, Hon. Mbr., 1913; Logan Prof. of Geology and Dean, Faculty of Applied Science. McGill Univ., Montreal, Que., Canada. '13 Adams, Gale L., Supervisor, Process & Dev. Lab., General Pet. Corp. of California, Higgins Bldg., Los Angeles, Calif. '18

Jan 1, 1939

In the examination of an undeveloped prospect a decision must be arrived at from an inspection of the outcrops and the exposures in a few shallow pits. Prospects that are offered for sale rarely expose any important quantity of good ore, work having usually been stopped when the immediate exploration no longer yielded favorable results. It should be borne in mind, furthermore, that a great majority of prospects have been examined many times, and if of conspicuous promise, would have been acquired-for development. In most cases the problem for the engineer, therefore, is to discover the traces of a valuable mineralization that has disappeared through solution, or the conditions that indicate the possibility, or probability, of underlying secondary enrichments. The available data being meager, every feature should be the subject of careful study-the condition of the outcrop, the structural relationships, the associations of minerals, the alterations of wall rocks, the chances for underlying enrichments, and so forth, as well as the actual assay value of the material exposed. It is frequently advisable to spend the time and money necessary to have trenches dug at various significant points along a promising outcrop; such exposures, even if the depth attained is slight, often disclose conditions that are not apparent at the actual surface, as for example, the existence of soft minerals and the distribution of the various minerals through the mass of the deposit. Trenches also permit samples to be taken from points that were not accessible during former examinations. Strong, persistent outcrops of uniform width may be taken to indicate the probable size and character of the underlying vein,

Jan 1, 1932

By Molly Gleiser

The standard free energies of formation of some gaseous metal oxides together with those of their condensed oxides have been plotted against temperature. The heats of formation of the gaseozcs oxides are tabulated. An explanation is given of the use of the data to predict the importance of the gaseous metal oxides at high tenzperatures. RECENT mass spectrometric work1 has resulted in the detection of several hitherto unknown gaseous oxides and the measurement of their free energies of formation. Of especial interest is the fact that several of the refractories in common use either as crucibles or furnace tubes, and metals used in Knudsen cells and in furnace windings, have been found to have one or more stable gaseous oxides. In view of the present emphasis on high-temperature techniques, the development of vacuum metallurgy.z heating by electron bombardment and plasma jets, and the resultant shift to ever higher temperatures, it is no longer possible to plan experiments without taking into consideration the significance of the presence of these gases in the system, the reactions they undergo. and their contribution to the vapor pressure. A good example of what went wrong in earlier work, when the existence of these gaseous molecules was not yet known, is presented by the work of Hoch, Nakata, and Johnston. Hoch and coworkers attempted to measure the vapor pressure of solid ZrO2 by letting the vapor in equilibrium with zir-conia effuse from a tantalum Knudsen cell. The free energies of formation of solid zirconia and tantala are such that a short calculation showed that the reaction

Jan 1, 1962

By J. E. Clennell

It is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although .a good deal of study land research has been devoted to the chemical problems [involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. Part I. Advances in the Chemistry of Ore Treatment by Cyanide In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved. Other efforts have been directed to improving extraction by electrolysis of working solutions, and by addition of various chemicals with or without electrolysis; to the diminution of cyanide consumption by "re-

Jan 1, 1916

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reason- able expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In a bulk tonnage product such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: 1 (I) by screening or sizing, (a) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing,

Jan 1, 1943

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800' C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By Robert Archer

IT is now well known that the structure of aluminum-silicon alloys can be refined in a rather remarkable manner, with consequent improvement of physical properties, by certain treatments applied to the molten metal shortly before casting. The differences between the treated and the untreated alloys are so marked that special terms are used to distinguish them, the untreated alloys being referred to as "normal" and the treated alloys as "modified." The first practical method of accomplishing this result was that of A. Pacz,1 which consists in treating the molten metal with a, salt flux of which the, active ingredient is sodium fluoride. The result can also be brought about, and in a more economical manner, by the addition of small quantities of metallic sodium (or potassium) to the molten alloy shortly before casting.2 The action of the Pacz flux evidently consists essentially in the production of free sodium by the reaction of sodium fluoride with aluminum. The changing of a normal alloy to a modified alloy is referred to as "modification' and any process for accomplishing this result is a "modifying" process. Modified aluminum-silicon alloys were introduced several years ago, and it has been demonstrated both in the laboratory and in commercial practice that it is no simple matter to produce castings having the maximum or nearly the maximum properties which under favorable circumstances can be obtained. The alloys are rather sensitive to small changes in chemical composition, and the modifying process must be carried out in a very particular manner to obtain the best results. Extensive experimental work has been carried out in the laboratories of the Aluminum Company of America with the object of determining the conditions that must be observed to make these alloys of the greatest possible

Jan 2, 1926

By T. S. Blair

I feel a certain sense of responsibility in bringing before you the subject of the direct process in iron manufacture. I am aware that, in such a body as I have now the honor of addressing, there are few who are not already so well informed upon its past history that it would be a weariness to them to listen to anything else than an account of practical success. Yet, to claim that success involves so much that, if I do not make good my claim, I deservedly expose myself to severe criticism. The whole literature of the art, so far as it relates to the direct process, is, up to this time, but a history of failure. It is safe to say that more money, time, and talent have been fruitlessly spent in the pursuit of this object than in all the other unsuccessful efforts in the whole line of iron metallurgy. A distinguished authority in patent law has remarked that " the invention records of the United States and of foreign countries are filled with the waifs and abandoned relics of these abortive struggles." Dr. Percy, whose great work may be taken as an epitome of all that was worth mention, whether useful or curious, in pig-iron metallurgy, up to the date of its publication (1864), after giving elaborate accounts of various attempts at the direct process, condenses his own opinion of all that had been then effected, into a brief but summary comment upon a pamphlet of one of the sanguine inventors who had said: "It is evident that the present mode of working iron

By S. F. Shaw

IN 1913, the Tiro General mine, at Charcas, S.L.P., Mexico, which had been making from 125 to 150 gal. of water per min., was allowed to become flooded, after all the pumps had been removed, and in 1918 the problem of unwatering it came up for solution. There are two vertical shafts, the Tiro General, 1390 ft., and the San Fernando, 1225 ft. in depth, with five connecting levels between them. The San Fernando shaft had been partly retimbered, while the Tiro General had been newly timbered from the collar to, 1090 ft. in depth. It had been possible to place guides in only one compartment of the Tiro General, from the collar to the seventh or 850-ft. level, to which it was necessary to lower the water before station pumps could be installed. Soundings indicated that compartments in the Tiro General were open to 1082 and 428 ft., and in the San Fernando shaft to 471, 488, and 586 ft. The water had risen to a point 140 ft. below the collar of the Tiro General shaft. PUMPING EQUIPMENT The steam plant at the Tiro General shaft includes one 300-hp., one 150-hp. and one 100-hp. Erie City water-tube boiler, and two 160-hp. Heine water-tube boilers. All but one of these boilers were supposed to be in good shape, but it was soon discovered that six years of idleness in a climate that is foggy for several months of the year had left them in poor condition. The compressed-air plant comprises one Nordberg cross-compound compressor with piston displacement of approximately 2500 cu. ft. of free air compressed to 96 lb. per sq. in.; and another Nordberg cross-compound with piston displacement of 1235 cu. ft. of free air, to the same pressure.

Jan 2, 1920

By Richard H. Terhune

The use of water-cooled breast-jackets or cinder-tap blocks is a great convenience in lead-smelting, even when siliceous slags are made. If the charges are at all basic it is almost imperative. Jackets of riveted wrought-iron or steel are expensive; those of cast-iron are liable to crack; those of bronze are costly and not durable, being easily penetrated by tapping-bars or destroyed by streams of matte impinging against them. To overcome these objections I introduced at the Hanauer works, in April, 1886, castjackets of steel, which have been in constant use since that time and are to-day as good as new. These jackets were made for us by the Chester Steel Castings Company, of Chester, Pa., at a cost of ten cents a pound at the works of that company. The metal is 5/8-inch thick, and the jackets were cored and tapped for l1/2-inch bushings, affording two large holes for the removal of dirt and incrustations. The same holes are used for feed- and discharge-water through 3/4-inch pipe. I hope the successful introduction here of cast-jackets of steel will lead to their more extended use in all branches of metallurgy where water-cooled surfaces are severely taxed, and where the size and thickness of the castings are not unfavorable to the production of a sound article, impervious to water and of high tensile strength.

Jan 1, 1889

The following communication was recently sent President Wilson by J. Parke Channing, Chairman of the Engineering Council: The transportation systems of our country are largely the creations of its professional Engineers. This statement can be made without disparagement to the statesmen, the financiers, the manufacturers, the lawers, the educators, the mechanics, the laborers and many others, who, with the Engineers, have contributed to the development of transportation. Through all stages of preliminary exploration, final survey, construction, upkeep and operation, in financial management, and in adjustment of the relations of transportation to the public, the genius and knowledge of the Engineer are essential. Not only in technical physical matters, but also in determinations of policy, his contributions have supplemented and must ever supplement those of other men. These declarations hold good for all the carriers of commerce, by rail, by highway, by water, by pipe-line, by wire, or by air. Hence, it follows that the body established by Government to regulate the commerce, the carriers and the ways of communication, embracing so many engineering features, should number among its nine members, men of engineering training and experience. Engineering Council, being aware of a vacancy on the Interstate Commerce Commission, begs leave to request the Chief Executive that in filling this vacancy, he give earnest thought to the selection of a man who, to his other qualifications, adds the training and experience of an engineer familiar with transportation problems.

Jan 9, 1919

By Henry M. Howe

Henry M. Howe, Bedford Hills, N. Y. (communication to the Secretary.)*—Mr. Johnson's explanation, that the rounding of the graphite masses in oxygen-bearing cast iron is due to their being in part reprecipitated after re-solution in forming carbonic oxide temporarily with.that oxygen, is certainly most attractive and suggestive. It remains to be shown whether this rounding occurs also when the solidification is too rapid to permit this process to go on. J. E. Johnson might easily test this by casting a single ladleful of his oxygenated iron in masses of varying size. If this present hypothesis is true, then the rounding ought to increase progressively with the size of the casting, and with the distance from the outside, that is to say with the time available for re-solution and reprecipitation. I question whether a like benefit is to be expected even on this hypothesis, from the oxygenation of steel. The spheroidizing of graphite does good because graphite itself is so weak. But the constituent which can be spheroidized in steel is its cementite, which is a source of strength. Lamellar pearlite, in which this cementite in effect forms long den-drites, is far stronger than divorced pearlite, in which these dendrites have been broken up into spheroids. Even the surfaces of contact between ferrite and cementite are probably sources of strength because of the amorphous iron which probably fills them.

Jan 1, 1917

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

By R. L. Vaughn, A. G. Moon

In 1972 a major renovation of the flotation and regrinding circuits was completed at Kennecott Copper Corporation's Chino Mines Division concentrator at Hurley, New Mexico. At that time a new lime distribution and control system was placed in operation. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of principal copper minerals, chalcopyrite and chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite, much of which occurs as intimately associated chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the desired pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. Test Work Plant test work on a lime control system using conventional pH probes gave disappointing results with high electrode maintenance and poor control characteristics. For example, the rougher flotation cells are operated at a pH between 11.4 and 11.6 and the probes required cleaning at least once a day, and occasionally every shift. These high maintenance requirements were considered unreasonable for a plant-wide system using six or more control loops.

Jan 1, 1979

Mine Transitman.-Engineer, about 30 years of age, experienced in coal mine underground surveys. Must be good draftsman and possess sufficient personality to get results from the men. Location, Illinois. No. R 419. Coal Mining Engineer: Coal mining engineer of proved ability for position of manager f high-grade bituminous coal property. Location, Canada. No. R 427. Chemist or Metallurgical Engineer.-Chemist or metallurgical engineer for special library work. Man with scientific training with the ability and education -of a young instructor in a university. Duties would consist of working out a new method of indexing scientific information, more particularly in obtaining information for use of a Committee on the Heat Treatment f Steel. Location, Washington, D. C. No. R 470. Topographical Draftsman.-Civil engineering training and topographical and surveying experience. Unmarried man, under 40 years of age. Knowledge of Spanish not necessary. Discharged army or navy man preferred. Location, oil fields, Mexico. Salary, $5 per day, living and traveling expenses. No. R 483. Mechanical Draftsman.-Engineering training, familiarity with drawings of pumps, piping, etc., need not necessarily be a designer. Unmarried man, under 40 years of age. Discharged army or navy man preferred. Location, Mexico. Salary $5 per day with living and traveling expenses. No. R 484. Engineer Translator.-Engineer of Portuguese nationality who has received his technical training abroad, and has been filling engineering positions in this country, to translate material for catalogs of an engineering character. No. R 486.

Jan 5, 1919

By William Garrett

I have heard it said that the late Mr. Holley made use of this remark: " There is an inherent, cussedness about rolls which, so far, no man has been able to find out." I think this can be safely claimed in reference to steel, as there are certain peculiarities about it that are pretty hard to account for. Previous to the introduction of the Bessemer process there was, as it were, a great chasm between iron and crucible steel; and, outside of what futile attempts had been made in puddling steel, nothing had been done to fill this gap. The Bessemer steel struck a medium between the two, the softest of it not being able to take the place of good iron, while the hardest was not suitable to encroach very far upon the crucible-steel trade. The open-hearth process made quite an inroad into the latter, but only for the lower and cheaper grades; and, beyond a doubt, for the finest grades of tool-steel, the cruciblesteel business has a long life before it. On the other side of the line comes the " basic " process, which brings us a step nearer iron ; but to fill up the gap completely, comes the Clapp-Griffiths process, which makes a grade of material—call it what you will—that is as soft as iron, welds as readily, and is in a fair way to supersede iron altogether. For fifteen years, I was in the employment of the Cleveland

Jan 1, 1886

By John S. Bell, J. M. Shepherd

pressure difference of 280 psi measured initially on opposite sides of the major fault in the Hawkins Field led to pressure determinations in the Woodbine sand throughout the East Texas basin. Considering the large area, there is unusually good correlation between pressure losses and points of major withdrawals, these losses indicating that the basin pressure has been materially reduced by withdrawals, primarily from the East Texas Field and secondarily from the old fault-line fields of Limestone and Navarro counties, with the pressure loss varying inversely with the log of the distance from these two main areas of basin withdrawals to the measurement points. Apparently faults located throughout the basin serve as local blocks to continuous pressure gradients. INTRODUCTION The pressure anomalies found in the Hawkins Field, Wood County, Texas,' shortly after discovery have led to an area-wide investigation of the pressure distribution within the Woodbine sand of the East Texas basin. These pressures were obtained by drill-stem tests made for that sole purpose while drilling wildcat wells to deeper horizons. The Woodbine sand of Gulf Cretaceous Age is or has been productive of oil and gas in 42 different fields, with the 28 oil fields currently active having produced 118,000,000 bbl of oil during 1949. With one exception, producing energy for all Woodbine reservoirs has been from water drive provided predominantly by expansion of the tremendous volume of water contained in the Woodbine sand. This producing mechanism was recognized at an early date and was described mathematically by

Jan 1, 1951