Search Documents

By James A. Barr

THE writer's first experience with flotation was during World War I, in the beneficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added. The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals Separation mechanical flotation machines were used in another graphite mill. Pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"[t] using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the Phosphate Recovery Corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for beneficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., subaeration types, with weir control of pulp between cells. The sand bleeders were very small-about 1 ¼ -in. diameter. As the feed contained 15 to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. I and details of the cascade construction in Fig. 2. The cascade installation in plant No. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1945

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949

By Wallace F. Lovejoy

The conservation of mineral resources as a public policy question has received a great deal of attention in the area of petroleum and practically no attention in other mineral areas, except, of course, soil and water. Some insights into mineral conservation problems and how these problems can be approached in the social decision-making process are significant. THE MEANINGS OF CONSERVATION Conservation means many things to many people .2, 11 Too often it is a label attached to a proposed program or policy to add respectability and to gain public acceptance. It is a term applied to specific resources in some contexts and to resources generally in other contexts. The oft-quoted comment of President William Howard Taft that conservation is something everybody is for, no matter what it means, succinctly illustrates the confusion over both the meaning of the concept and the policies required to implement a conservation program. This confusion goes quite deep and is more than a matter of semantics or emphasis. For example, the efficient exploitation of a mineral deposit which might be applauded as good conservation in terms of that mineral, might well result in destruction of or harm to the environment which might be viewed as bad conservation. Economics provides some tools to help solve this sort of problem, but there may be fundamental differences in value systems among groups in this society, so that ultimately society must collectively make a subjective political choice as to what is good or bad conservation policy.a An Economic Definition of Conservation The economic concepts of conservation have more relevance and are more easily applied to minerals than to many other natural resources. This does not mean that economics goes all the way in understanding mineral conservation, but at least it provides a framework for analysis which later can be altered to include noneconomic variables. Perhaps the greatest confusion in discussing mineral conservation arises in attempting to relate purely physical concepts with economic concepts. An economist is interested in maximizing or conserving values; he is not interested in maximum physical recovery or utilization. He wants to know the costs and benefits of using, or not using, resources. The economic theory of mineral-resource conservation can be labeled variously as the theory of exhaustion, the theory of resource exploitation, the theory of resource utilization, or simply as a special case of the broad theory of capital.4,28 Consideration of these labels illuminates the concerns of the econo-

Jan 1, 1976

By P. C. Badgley

The purpose of this paper is to demonstrate the usefulness of systematic analyses of weakness patterns. The term weakness here includes structural features such as fractures, foliation planes, lineaments and bedding. Many of these features are mapped by geologists in the field, but analysis of the field date is frequently overlooked. Examples are presented to show the value of such studies in petroleum and mineral exploration, in dam site selection, and in regional tectonic interpretations. Numerous theories have been presented to account for the mechanics and time of origin of fracturing. This is an extensive subject and cannot be reviewed in detail here. The reader may wish to refer to other papers.*"5 It is sufficient to say that most fracture patterns can be related to one or more of the following force mechanisms: compression, tension, torsion and fatigue (inheritance by upward propagation of pre-existing fractures). Fractures generally occur in sets in a district. The angular relationships and other characteristics of the individual sets frequently help in determining the force mechanism and movement history of the deformation. From a geometric point of view fractures are commonly referred to as longitudinal, cross, or diagonal (shear), depending upon their orientation relative to other major structural features such as anticlinal axes and so forth. These terms will be used from time to time and are illustrated schematically in Fig. 1. FIELD PROCEDURE AND TREATMENT OF DATA In fracture studies it is very important to collect adequate field data. Fig. 2 illustrates a notebook sheet for recording significant field observations in sedimentary rocks. Slight adaptations have to be made for igneous and metamorphic terrains. Fracture density and persistence are very important factors in petroleum exploration for fractured reservoirs and mineral exploration. The density for each joint set is recorded in terms of number of joints per linear yard. The total number of joints at any one

Jan 1, 1962

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;' this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.' Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.' The effect of stress on M, (2°C per kg mm-') was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-'. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). 'A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. 'C. Crussard: Comptes Rendus (1953) 237, p. 1709. ' G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By C.A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By C. A. Zapfee, C. E. Sims

An investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. Apparatus The apparatus is shown in Fig. r and the system is shown by diagram in Fig. 2. Furnace, A lmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In this furnace fres oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1943

By R. Taggart, J. W. Barton, G. R. Purdy, J. G. Parr

The constitution and mechanical properties of heat-treated alloys containing up to 10 pct* Ni in Ti have been investigated. The effects of quenching and of various isothermal treatments ale described, and C-curves are presented. The production of the precipitated and the martensitic hexagonal phases on quenching is discussed. MARGOLIN, Ence, and Nielsenl have determined the titanium-nickel phase diagram. A study of the transformations in gas-quenched and tempered powder specimens was made by Polonis and Parr.' Some isothermal transformation work was carried out by Margolin and ~unshah, who determined transformation curves for 4 and 6 wt pct alloys, while Robinson et al.investigated the formation of the w phase in a quenched and tempered alloy, Margolin and Bunshah showed that while a martensitic transformation could be obtained on quench- ing thin sections of a 4 wt pct alloy, a 6 wt pct alloy precipitated a nonmartensitic phase. The present investigation was undertaken to obtain more information on the transformations in quenched, quenched and tempered, and isothermally transformed lump specimens of alloys containing up to 10 pct Ni. Isothermal transformation curves have been determined for 7 and 10 pct alloys and cooling curves have been obtained for quenched alloys containing up to 7 pct Ni. The mechanical properties of 2, 5, and 10 pct alloys were studied, with the object of relating properties to microstructures. EXPERIMENTAL METHODS Alloys containing up to 10 pct Ni were prepared from sponge titanium and spectrographic standard nickel by levitation-melting and chill-casting in a split copper mold. The 5 and 10 pet alloys were prepared from sponge Ti having an as-melted hardness of 115 Vpn. The other alloys were made from a sec-

Jan 1, 1961

By G. E. Murray

Lead blast-furnace work at Trail is unique in that this is the only plant in the world where blast-furnace smelting on a large scale for both lead and zinc recovery is carried on under one management. On this account the factors that determine economic practice differ from those of other lead smelters. In addition to this different metallurgical outlook, a great deal of structural investigation has been carried on, which has resulted in the development of a furnace which should prove of interest to all who are faced with similar problems. This description may be conveniently divided into various heads as follows: (1) General—make-up of charge, etc.; (2) structural—(a) hoods and charging methods, (b) shaft construction, (c) crucible construction; (3) handling slag; (4) handling bullion; (5) metallurgy. The Charge The Trail plant is an old one, on a congested site. As with most old plants, this limits the method of charge preparation. In general, lead metallurgists will agree that sinter when it reaches the blast furnace should contain as small an amount as possible of actual fines. There would be some difference of opinion as to the maximum size as well as of the minimum required, but to obtain the optimum condition some form of screening is indicated. This screening should take place immediately before the blast furnace if possible, and because sinter deteriorates in storage there should be as little as possible. There should also be the minimum amount of handling between the sinter machines and the furnaces. Unfortunately, at Trail the sinter must be handled considerably before it is charged to the furnace, and no feasible scheme of screening has yet been devised. Trail practice, then, demands that the sinter be a strong one physically. Dependent upon the amount of lead in it, it has been found advantageous to incorporate granulated slag into the final sinter, the amount varying inversely as the lead content. The addition of this slag makes a harder sinter, which arrives at the blast furnace in a better condition, but it entails some lack of efficiency, because desulphuriza-tion is not so rapid nor so complete.

Jan 1, 1937

By C. O. Brawner

INTRODUCTION Tailings dams up to about 200 ft. high are proposed to store tailings for a major mining operation on Marinduque Island in the Philippines. The original design of the dam utilized a compacted laterite starter dam followed by hydraulic placement of cycloned sands to form slime retaining dykes along the outer face of the dam. The upstream method of construction was proposed. In view of the failure of numerous tailings dams in Chile during the EL Cobre earthquake (I), an investigation was performed to assess the earthquake stability of the proposed dam. This included a soil investigation on the first cycloned sand dyke, which had been built to a height of 45 ft. Results indicated that the density of the sand was much lower than existing empirical criteria consider to be necessary for resistance to liquefaction. As a result, the dam was redesigned. The downstream method of construction was selected and a yearly construction program was developed to make use of sand available by cycloning. To increase shear strength, improve resistance to liquefaction, and to utilize steeper slopes, compaction of all sand in the dam was specified. A special underdrainage layer and toe drains were incorporated in the design. Details of the decant system and surface erosion alternatives are described. SITE CONDITIONS The mining project is located in the Philippine Islands. At the present annual rate of production, about 4,230,000 cu.m. of tailings will be produced yearly. The volume requirements for tailings storage design for the first 10 years of operation are in the order of 45,000,000 cu.m. The topography near the mine is mountainous with many gullies and canyons carved out by high intensity rainfall and runoff. The bedrock, which is generally shallow and weathered for a considerable depth, is overlain by laterite soils. Vegetation is comprised largely of palms, banana trees, and tropical shrubs and grasses. Precipitation is heavy. The average yearly rainfall over 24 years is 65.2 in. and the maximum recorded 24 hour rainfall is 9.0 in. High intensity rainfall is associated with typhoon storms, which are a seasonal threat inthe Philippines. Fig. 1 shows a summary of monthly precipitation.

Jan 1, 1972

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination ' of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

The General Committee met in the Treasury Building at Washington on Oct. 6 and 7. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary. Sub-committees were ap-pointed on Invested Capital, Mine Valuation, and Depletion and De-preciation. On Oct. 7, the reports of these committees were submitted to the General Committee and were referred to the Executive Committee. A motion was carried that the Executive Committee he constituted a permanent committee to continue the work of the Committee, with full power to acid to and increase its membership, that. as thus increased, it should constitute a permanent organization to act- and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Com-mittee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, office of the Commissioner of Internal Revenue, Wash-ington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St., New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, Engineering and Mining Journal, 10th Ave., and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, Peabody Coal Co., McCormick Bldg., Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City. William G. Mather, Cleveland, Ohio. Walter Fitch, Eureka, Utah. Arthur Thacher, 900 Security Bldg., St. Louis, Mo. John P. Gray, Coeur d'Alene, Idaho. Paul Armitage, secretary, 233 Broadway, New York City.

Jan 12, 1919

By W. S. Steele

Vermiculite is a nonmetallic mineral of the mica family, probably related to biotite mica. Its occurrence has been noted at numerous places in the United States and in some foreign countries, but it can be said that vermiculite is of only moderately wide distribution. A laboratory and field survey of over 60 deposits in the United States by F. 1;. Schundler & Co., of Joliet, Ill., indicates that the purest deposit represented in this survey is on the property of the Zonolite Company at Libby, Montana The Zonolite Company is commercially active and the vermiculite it produces is sold as Zonolite. Hereafter, in this report, the word "Zonolite " will be used to designate the vermiculite produced by the Zonolite Company. Values given herein to Zonolite are peculiar to the vermiculite produced from the Zonolite Company's deposits. References to " vermicullite," are to he interpreted as covering the broad field covered by the Schundler survey. Composition and Characteristics of Vermiculite Vermiculite is an aluminum-nmgnesium silicate. The following typical analysis is published by the United States Bureau of Standards: silica, 41 per cent; iron oxide, 7; aluminum oxide, 18; magnesium oxide, 21; calcium oxide, 1; alkalis (sodium and potassium), 1; moisture, 11. Vermiculite breaks down into platelike formation in crushing and grinding operations. Its cleavage is basal. Crude, screened, dry Zonolit,e weighs between 80 and 90 Ib. per cubic foot; its specific gravity is 2.8 and its specific heat is approximately 2. The fusion point of Zonolit'e is 2462" F. Crude vermiculite contains between 7 and 9 per cent of chemically combined moisture. The instantaneous introduction of crude Zonolite into an expansion furnace at a temperature of between 1800" and 2000" F. transforms the combined moisture into steam, which in an effort to liberate itself forces all explosive expansion of the platelike crude material

Jan 1, 1934