Search Documents

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By Joseph S. Young

During 1975, the Reclasource Corp. constructed and started up a plant for the recovery of mill scale, coke breeze, blast furnace dust; blast furnace sludge; and TOC dust, at the site of Crucible Steel, Inc., Midland, Pa. The Reclaform Process was employed as the criteria for plant design. This process takes the solid wastes (as listed above) which are commonly found in integrated steel mills, sizes them, forms them through the use of a carbonaceous binder briquetting system, and fixes the binder through a final heat treating step. Blast furnace tests have been performed on 15,000 tons of Reclaform briquets. This paper gives a brief history of the program, and describes the process and the raw materials involved. The blast furnace campaign and its major conclusions are discussed.

Jan 1, 1977

There's a right way and a wrong way to store diesel electric systems and similar equipment for generating on-site power, according to James Frankow, service manager for Allis-Chalmers Corp's Engine Division. In any event, the less storage the better. Many generating sets are stored before installation, especially when new construction is underway. Improper storage, or mothballing, can create initial reliability problems. Therefore; arrange for inside storage with no drastic extremes in temperature or humidity. If engines and alternators are stored in areas other than inside a dirt-free and temperature-controlled building, the unit or engine should be completely covered and protected against the environment. Before covering it with a canvas or with plastic, the unit should first be sealed at the following critical engine openings:

Jan 3, 1978

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.'. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"' * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By Hugo L. Johnson, Robert Wallace

THE Midvale plant of the United States Smelting Refining and Mining Company consists of a flotation mill for concentrating sulphide ores of lead and zinc by differential flotation to produce three separate concentrates, one of lead, one of zinc, and one of iron pyrite; and a lead smelter for smelting ores and concentrates to produce base lead bullion, The plant, including its shops, laboratories, office, railroad yards which serve both mill and smelter, and areas reserved for tailing ponds and slag dumps, covers 646 acres on the right bank of the Jordan River at Midvale, Utah. It is twelve miles south of Salt Lake City and sixteen miles east of the West Mountain mining district at Bingham Canyon from which is drawn a large part of its ore supply. Custom ores are treated as well as the product of Company mines.

Jan 1, 1948

By W. Ivanick, Frank W. Glaser

ORDERING reactions of Fe-Si compositions in the a region have been mentioned in a number of review articles.7-8 However, little is known in regard to the critical temperature, T at which this transformation takes place. Greiner and Stoughton,' in a study of the constitution of iron-rich Fe-Si alloys below 800°C, placed the onset of order at a composition of about 4 to 5 wt pct (7.5 to 9.5 atomic pct) Si. They observed that at this composition the ductility and strength begin to decrease sharply and brittleness develops. During X-ray studies they observed only the appearance of superlattice lines for compositions containing 12.5 atomic pct Si. More recent X-ray diffraction studies- etected the appearance of superstructure lines (corresponding to the calculated positions of [Ill] and [ZOO] reflections) for alloys containing 9.5 atomic pct. This fact confirms Greiner and Stoughton's original hypothesis in regard to the onset of order at compositions containing about 7.5 to 9.5 atomic pct Si. The physical properties.of Fe-Si alloys containing more than 10 atomic pct Si have been studied only to a limited extent. Their extreme brittleness and difficulties of sample preparation render them of little industrial use in comparison with alloys in the 0 to 10 atomic pct Si range. The properties of Fe-Si alloys reported to date are mostly properties measured at room temperature on ordered compositions It appears that because of experimental difficulties fully disordered alloys could not be produced in the critical composition ranges and their properties could therefore not be reported. In Figs. la, lb, and lc, a summary of physical properties of Fe-Si alloys, measured during recent investigations of the influence of silicon additions to iron, is presented. No mention of determination of the critical temperature, T for disorder could be found in the literature. The following is an account of work done in an attempt to: 1) produce the disordered state of various Fe-Si alloys and establish the critical temperature, T for disordering, and 2) compare the electrical and thermal conductivity characteristics of the ordered and disordered phases as functions of composition. Materials, Preparation of Test Samples, and Testing Methods Fe-Si alloys with high silicon contents (about 10 atomic pct) are usually prepared using powder metallurgy techniques. This method insures accurate compositions and high purity through the use of protective atmospheres during solid state diffusion alloying of the mixed powders."" Iron and silicon powders were mixed in the desired proportions, cold or hot pressed, and then homogenized at 1150°C for periods ranging from 6 to 12 hr under a protective getter and in a hydrogen atmosphere. Fully homogenized samples were quenched in water from various and successively higher temperatures to establish the critical temperature for disorder. Temperatures were determined using Pt—Pt-Rh thermocouples in contact with the test samples. Test bars were approximately 0.6x1.25x7.5 cm. Electrical measurements were made at room temperature by determining the potential drop over a 1.5 cm span for a current of 10 amp. Densities of the samples were determined by immersion. High temperature electrical resistivities were measured using previously described techniques.'" Specific heat conductivity up to 200°C was measured by heating one end of the test bar and water-cooling the other; heat conductivity was then obtained by subtracting the rate at which heat entered the water from the

Jan 1, 1957

By E. J. Efsic, C. M. Wayman

The fcc to bcc y to a transformation in an Fe-24.5 at. pct Pt alloy was studied and found to be martensitic. Large martensite plates are formed in this alloy which are ideal for crystallographic studies; the Ms temperature is about -5°C. Ordering of the parent phase prior to transformation to martensite causes a pronounced lowering of the Ms temperature. For the first time in the case of alloys of iron, measurements of the habit plune, orientation relationship, and magnitude and direction of the shape stvain have been obtained on preselected martensite plates. It is shown that by measuring the initial and displaced (as a result of the shape strain) positions of three or more non-parallel fiducial scratches on one reference surfice the maguitude and direction of the shape strain and the state of distovtion at the parent-mavtensite interface can be determined with a reasonable degree of accuvacy. The agreement between the phenomenolog-cal crystallographic theory of martensitic transformations and the experimental results habit plune, orientation relationship, and nlagnitude and direction of the shape strain) is essentially perfect, and is thought to be the best reported to date for iron alloys. THE comparatively few investigations on binary Fe-Pt alloys have been concerned with magnetic properties, ordered phases, and the equilibrium diagram itself. Various investigations have shown that the equilibrium diagram is of the open y field type; in addition there is a peritectic transformation, a minimum melting point, and three ordered phases: Fe3Pt, FePt, and FePt3. The results of a number of investigators1-6 have shown that the temperature dependence of the y to a (and reverse) transformation in iron-rich alloys is reasonably well-established. The Fe3Pt phase was first noted by Kussman and Rittberg,7 and its existence was later confirmed by Franklin et al,8 Steijn and Donahoe,9 and Berkowitz et al.10 The FePt phase was reported by Isaac and amman' and later confirmed by a host of others.3,6,7,12,13 Kussman and Rittberg7 noted the existence of the superlattice FePt3. Prior to 1956, the 1 to a transformation in iron-rich Fe-Pt alloys was termed "irreversible". In 1957 Klokholm and Donahoe" termed this transformation martensitic, presumably because of its occurrence at temperatures well below those where diffusion normally takes place. This observation served as a point of departure for the present investigation, and in the very early stages of the work to be discussed it was readily verified that the y to a transformation in iron-rich Fe-Pt alloys is indeed martensitic. Quite large martensite plates exhibiting the well-known surface tilt were observed. These plates are ideal in the sense that the boundaries between the parent and product phases were usually very straight. It thus appeared that Fe-Pt martensites would be ideal for crystallographic studies, and this was the purpose of the present investigation. Details of the crystallography of martensitic transformations (particularly for iron alloys) and the phe-nomenological crystallographic theories15-l7 have been discussed many times and thus will require very little elaboration here. The end result of these theories, given in matrix form, is

Jan 1, 1968

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a [?] line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and [?] lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz," This would require many data to prove, but no proof is given; any considera¬tion would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.¬Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg8 have ground

Jan 1, 1941

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling, It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.-Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystal-line solids. Andreasen and Berg8 have ground

Jan 1, 1941

By P. S. Roller

P. S. ROLLER,*College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should he defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. x between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.," Cambridge, Mass. Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids., Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg' have ground

Jan 1, 1941

By Arthur F. Taggart

MR. CHAIRMAN: Congratulations! Your four-ring milling show this year was a dandy. It cleared our minds, for a few hours at least, of what Hitler, Hirohito, the New Deal, and the tribe in the Treasury are trying to do to strangle American enterprise. We mustn't forget this, but it's a relief to get our thoughts away from it occasionally. GRINDING-There was a further contribution to the excellent work that the Allis-Chalmers laboratory staff has been doing for the grinding fraternity in compiling-and publishing-a carefully quantitative list of comparative resistances of ores and other materials to comminution (T.P. 1579, Bond-Maxson). A diagnostic accuracy of ± 10 per cent was claimed for estimates based on these figures. Are they really that good? How about some of you men in the field writing M&M about it?

Jan 1, 1943

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By William Fink

NICKEL is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting proper-ties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investiga-tions of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available.

Jan 1, 1934

By AIME

Annual production of more than 4,000,000 tons of 0.74 percent copper ore and coincident handling of over 5,000,000 tons of waste at the open-pit mine of Castle Dome Copper Co. near Miami, Ariz. takes a lot of power. Manufacturers have ever co-operated with mining companies in providing the required equipment to suit the problem. Power equipment suppliers have done much to make possible the economic and profitable production of copper from low-grade ores. In the future, as mining operations will necessarily handle even lower-grade ores, the ability of the manufacturer to supply the power and mechanical equipment to produce more metal at a fair and reasonable price will be the good right arm of the miner. About 27,000 tons of concentrate is produced from the 4,000,000 tons of ore.

Jan 1, 1948

By Charles B. Dudley

In view of various papers and discussion.;, at recent meetings of the Institute, upon testing, methods of testing, inspectors, inspection and specifications, it has occurred to me that my experience of some fifteen years, in the making and enforcement of specifications, in connection with the Motive Power Department of the Pennsylvania Railroad, might give some value to the few suggestions offered in this paper. There is friction, not to say antagonism, between the producers and the consumers of structural materials. On the one hand, the producers complain of the severity of inspection, or the lack of knowledge and want of good judgment on the part of inspectors, and, indeed, have gone so far as to suggest the abolition of the whole scheme of inspecting and testing materials. On the other hand, the consumers are, apparently, more and more relying on specifications

Jan 1, 1893

By Raymond A. Bradbury

The first diesel-powered Scooptram has now been in service for 21/2 yr at the I-C mine of Martin County Coal Corp. It has become the workhorse of the operation, being used around the clock many days. The fleet of nine 20-ton capacity Teletrams used behind three Jeffrey Heliminers now have more than 1 1/2-yr experience in the Coalburg mine. They have been exposed to some difficult conditions which, include steep grades, water, mud, and rutted roadways. These units have proven to he both rugged and powerful. The safety components and shutdown systems make these haulage units very safe for underground coal mines. A clean-burning engine, a satisfactory exhaust conditioning system, and good ventilation are the keys to maintaining a safe and healthful atmosphere for the underground operators and other employees.

Jan 1, 1976