Search Documents

By R. A. Generes, H. C. H. Darley

Laboratory tests showed that at elevated temperatures a reaction takes place between all metal hydroxides and clay muds, which results in a thickening or solidifying of the mud, the extent of which depends on the nature of the ingredients. Calcium hydroxide gave the strongest solidification whereas barium hydroxide only caused a mild thickening, indicating that the use of barium hydroxide muds instead of lime muds would be a good way of preventing high-temperature solidification. It was found possible to prepare barium mud in the laboratory with caustic soda and a thinner in the same manner as lime muds, and these barium muds had the same or better toleration of high solids content, resistance to salt contamination, and low gel strengths as the corresponding lime muds. Three field trials have been made with barium mud. The principal difficulty encountered was in determining the correct proportions of the tourly treatments required to maintain low gel strengths. A satisfactory systern was finally developed, and low gels were maintained throughout the third test. The wells on which the trials were made were not carried deep enough to test the resistance to solidification adequately, but oven tests at 350°F were made periodically and no tendency to solidification was noted except immediately after severe cernent contamination had introduced excessive amounts of calcium into the system. Although barium hydroxide costs considerably more than lime, the total mud costs were as low, and on the last well significantly lower, than the average cost of lime mud wells drilled in the vicinity. INTRODUCTION The advantages of repressing dispersion and hydra-tion of clay cuttings carried in the mud, particularly when drilling through thick clay formations, are well recognized. This repression is generally achieved by the use of lime, and lime muds have in consequence the desirable characteristics of high toleration of solids, low thixotropy, and good resistance to contamination. They have, however, the disadvantage of high-temperature solidification. This phenomenon has been described in detail by Gray et al, who have shown that it is the result of a chemical reaction between the hydroxides and the clay minerals. The work described in this paper was undertaken to find a substitute for lime which would not cause this solidification. LABORATORY EXPERlMENTS The principal positive requirement for a substitute for lime is that it should repress the hydration and dispersion of clay. It is well known that monovalent cations promote hydration while polyvalent cations repress it. Therefore, a few representative polyvalent salts and hydroxides were tested to determine whether they could be used as substitutes for lime. Their efficiency at repressing hydration and dispersion was measured by means of the clay-volume test. It has been shown elsewhere' that this test is a good measure of degree of dispersion of clay in suspension and that hydration accompanies and correlates with dispersion, so that measuring one measures the other. The test is made by centrifuging a 1:100 mixture of mud and 1-N NaCl and observing the volume of sediment—the greater the volume, the greater the dispersion. The tendency to caux solidification was measured by heating the muds in pressure vessels for 16 hours at 150°F and 370°F. An approximate quantitative

Jan 1, 1957

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By W. A. Backofen, G. Mayer

Single crystals of iron, copper, and a Cu-7 wt pct A1 alloy were pulled through conical dies to simulate the constraint in a polycrystalline aggregate undergoing axisymmetric reduction. With Taylor-type hardening, dependence of the drawing stress, od, on the Taylor orientation factor, M, is predictable from the polycrystal stress-strain curve; in particular, for a power-law relationship, it should follow that d log od/d log M = (1 + n). A first-order agreement with analysis was found in the data from iron. For copper, the implied n from the observed d log od/d l°g M was -0, while for Cu-7Al it was negative. The trend was in the direction of random polycrystal behavior. Thus the idea of hardening only in response to the amount of prior slip loses validity as stacking fault energy (SFE) is lowered. Two possible explanations have been suggested: as stacking fault ribbons are widened, barriers from dislocation reactions become increasingly effective in dispersing slip and reducing the orientation dependence of the total glide strain dm that appears in alternatively, or conjointly, the polyslip shear stress, 7, acquires an orientation dependence of a kind which has the same leveling effect on M. The problem of relating the strain hardening of polycrystalline material to that of an isolated single crystal is still largely unsolved. In a new experimental approach from recent work, single crystals of different orientations have been deformed under the constraints found in an aggregate while measuring their deformation resistance. Procedures have involved drawing cylindrical crystals through conical dies1 and compressing slab-shaped crystals in plane strain.2&apos;3 Predictions for the outcome of such experiments were made first by Taylor~ and later, in more general form, by Bishop and Hill.5&apos;6 Taylor&apos;s example was the axisymmetric extension of an fcc crystal slipping on the usual {111}(110) systems or, equivalently, a bcc crystal undergoing &apos;kestricted" slip on {110}(111). In his solution, the deformation work supplied was equated to that dissipated internally in slip on all active systems. With o the single applied tensile stress, dc the resulting axial strain, and dyT the total glide strain on systems operating at resolved shear stress, 7: The orientation dependence of M was found by minimizing dyT for each orientation while activating five independent systems, Fig. l(a).? The Bishop and Hill analysis, based on a principle of maximum work, leads to essentially the same conclusion; the need for at least five active systems is recognized in the finding that either six or eight are actually brought into operation. The mean value from the entire stereo-graphic triangle in either case is M - 3.06. More recently, Hutchinson8 made a Taylor-type analysis for pencil glide in a bcc structure, from which piehlerg prepared Fig. l(b) as the counterpart in Fig. l(a); here M = 2.75. The obvious weakness in such analyses is the indifference to slip-system interactions. A condition of what might be termed "independent"

Jan 1, 1969

By Robert Forsyth

IN working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remark- able when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

Jan 1, 1876

By Stuart St. Clair

In view of the great interest shown in the oil possibilities of Kentucky, one is impressed with the paucity of reliable literature on the oil fields of the state. A few brief reports by the Federal and State Geological Surveys are about the only reliable data available. When the estimated production figures, for 1918, are published by the U. S. Geological Survey, they will show a revival of the oil industry in the Blue Grass State during the past half decade. There will also be an increase in the production for 1919 and 1920, at least. Although as an oil-producing state Kentucky is small, compared with some of the other oil states, the present production and the area of undrilled proved territory is large enough to classify it as one of the important oil states of the Union. This paper will be confined to the Irvine District and the immediately adjoining areas which have been prospected with varying success. The Corniferous limestone or Irvine sand is the oil-producing formation in the area discussed. In my divisional nomenclature, the Irvine District includes the Irvine field, which extends from the town of Irvine eastward toward Campton; the Big Sinking area, which joins and lies to the south of the eastern part of the Irvine field; the Beattyville area, which lies to the north and northeast of the town of that name and joins the Big Sinking area; and the Ross Creek pool, which lies to the southwest of the big production and across the Kentucky River. Except for the Ross Creek pool, the main producing area is bounded on the east by the L. & E. R. R. and on the west and south by the Irvine Branch of the L. & N. R. R. Winchester and Lexington form the gateways and Torrent on the east, Irvine on the west, and Beattyville on the south are the principle entrances to the main fields. Evelyn, on the L. & N. R. R., south of Irvine, is the point of entrance to the Ross Creek area. Geology The geology of the Irvine District is very simple. The rock formations with which the oil man should acquaint himself lie between the lower measures of the Pennsylvanian sandstones and shales and the Devonian or Corniferous limestone, or Irvine formation. Only a very brief description of these formations will be given, as they have been described fully by E. W. Shaw.&apos;

Jan 1, 1921

By C. A. Heiland

The following summary is written for the benefit of the practical operator in the nonmetallic field who wishes to know what geophysics has done and may be expected to do in his line of work. His problem is quite different from that of the geophysicist who has operated with various or all methods and has followed the literature, and who is assumed to be familiar with the geologic possibilities and limitations of each method. This article is not written for the latter, although he may be interested in the four or five hitherto unpublished surveys described. To the operator, on the other hand, geophysics is only secondary. His problem is to determine which geophysical method is best suited to his special needs. If he wanted to know, however, which method could be used to locate a certain material of given physical properties, building stone, for instance, he would have to wade through a tremendous amount of geophysical literature, bibliographies and articles, before he could find what he wanted. Therefore, the purpose of this summary is to present the geological problems first and then to discuss the comparative merits of the geophysical methods that can be, or have been, applied. Choice of Geophysical Methods in Oil, Civil and Mining Engineering In the first two of these fields, the geological problems are not nearly so complex as in the metal and nonmetallic mining fields. The selection of the correct geophysical method in these fields is not nearly so difficult for the operator. For oil prospecting, his problems have been discussed exhaustively by E. DeGolyer.(1) † In civil engineering (foundation and ground-water work), the usefulness of electrical methods has been so well established that there is hardly any choice of other methods at present. The situation may be changed in the future with the perfection of the seismic reflection method for shallow depths. In the mining field the operator and often the geophysicist himself finds difficulty in determining which method is best suited for a given

Jan 1, 1934

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-&apos; had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.&apos; Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By R. F. Krueger, L. C. Vogel, P. W. Fischer

Previous studies have shown that the permeabilities of sandstone cores are markedly reduced following exposure to drilling fluid and subsequent clean-up with oil at high-pressure gradients. Laboratory experiments reported in this paper indicate that permeability damage from drilling mud or water can be substantially avoided through use of an initial low-pressure gradient followed by gradually increasing gradients during clean-up by reverse oil flow. On the other hand, attempts to improve the permeability of damaged Berea and oil formation cores with high-rate oil backflush (simulated well stimulation) and low-rate clean-up gave erratic results. Essentfully complete permeability repair was achieved in most of the fresh water-damaged cores from Miocene and Pliocene oil-producing formations; only minor improvement was noted generally in tests with both water-and mud-damaged Berea sandstone. Field well stimulation treatments using high-rate back-flush resulted in long-term productivity improvement when production was brought in at gradually increasing production rates and then restricted to a steady value less than the maximum possible rate. Wellbore plugging at high production rates correlated with increasing solids content in the produced oil. Observations and results from these tests agree with current concepts that formation damage in water-sensitive rocks results from movement and bridging of formation fines, rather than from clay swelling alone. INTRODUCTION Many laboratory studies1-g have shown that the permeabilities of sandstone cores are often markedly reduced following exposure to fresh water or water-base drilling mud filtrate. However, work with cores in the restored state has demonstrated that, although permeabilities to water may be very low for sandstones containing hy-dratable clays, flow of oil can often restore a substantial portion of the effective permeabilities to oi1.Neverthe- less, water invasion into water-sensitive sandstone cores results in varying degrees of permanent reduction in permeability to oil.24&apos; Based on field data, Wade&apos;s statistical study" of well completion effectiveness also indicated a correlation between productivity damage and water invasion during completion. Similar damage can result from fluid invasion during workover. Nowak and Krueger&apos; and Bertness4 observed in their early work (1951-53) that formation damage in water-sensitive sandstones was associated not only with swelling of expandable clays but also with movement of dispersed particles. Subsequent work by Monaghan et al." (1959), Atwood&apos;&apos; (19641, Mungan" (1965) and Gray and Rex&apos;" (1965) has led to general acceptance of the hypothesis that permeability damage in water-sensitive formations is caused by migration of finely dispersed minerals and bridging in "brush heap" arrangements at pore constructions. In laboratory studies, Monaghan et al.&apos; found the use of chemicals to be of only minor value for repairing formation damage. Atwood? however, was successful in substantially repairing damage in a number of low-permeability cores using an n-hexanol flush. In the field, except for treatments with acids, the use of chemical washes to reduce wellbore damage has had limited and sporadic success and generally is unpredictable. A statistical analysis of stimulation treatments in silt-blocked wells has shown that physical manipulation of wash materials is more important than chemical composition." The recent work reported on formation damage in water-sensitive sands brings to mind the results of some unpublished exploratory work done in 1954 in connection with drilling fluid studies.&apos; This laboratory work and subsequent field stimulation treatments indicated a beneficial effect of controlled pressure drawdown and the associated production rate on formation clean-up. This paper reports the results of this work and more recent supplemental experiments on the clean-up of water-sensitive sandstones damaged by water or filtrate invasion. PERMEABILITY RECOVERY AFTER DAMAGE BY DRILLING MUD APPARATUS AND TEST SAMPLES A drilling mud circulating system was used to expose cores to simulated wellbore conditions. The mud flow system is the same as that described by Krueger and Voge17 except that no provision was made for scraping

By Ikuya Takase

INTRODUCTION Since the occurrence of the first oil crisis, coun-tries of the world, especially oil-importing countries have made sustained and vigorous efforts to lessen the dependency on oil as a source of energy supply. The adoption of "Principles of Coal Policy" by the IEA Ministerial Governing Board Meeting in May, 1979 was the first formal action taken by major energy consuming countries. At the Venice Summit in June, 1980, it was agreed that production and use of coal should be doubled over the next ten years. In fact, the world coal use in 1980 showed around a 10 percent increase over the previous year. Recently, we have seen an indication that the balance of oil supply and demand in the short term have eased. But I believe that it remains vital that we continue to encourage the development and introduction of alternative energy sources. Because, from the medium and long range viewpoint the recovery of the worldwide economy will lead us to increased oil requirements and thus we will be faced with the cyclical, structural tightening situation between the supply and demand of oil. Moreover, we are still convinced that the constraint of the supply capabilities of the Middle-East nations may be increasing in the long-term, since there still remains political uncertainties among these nations. Consequently, above all, coal is viewed as an alternative energy resource available for immediate expansion of use and is given as high a priority as nuclear power. In Japan, we regard coal as the most reliable alternative energy resource to replace oil. According to the "Alternative Energy Supply Targets" approved by the Cabinet in November, 1980, the level of coal imports is estimated to approximately double by 1990, while our domestic coal production will remain nearly at the same level. The transition from oil to coal is found in the recent import levels of coal---73 mil¬lion tons in 1980, a 23 percent increase over the 59 million tons imported in 1979. There was an upsurge in steaming coal imports, reflecting the transition in feedstocks---7.2 million tons in 1980, four times over the previous year&apos;s amount. Henceforth, from the medium to long range view, the demand for coal, especially that of steaming coal is forecast to continue to grow. The timely expansion of supply capabilities is our utmost concern and should be one of the most significant goals of our comprehensive policy. The Overseas Coal Investigative Committee, a privately organized advisory panel to the Director-General of the Natural Resources and Energy Agency of the Ministry of International Trade and Industry (MITI), investigated means to secure a stable supply of overseas coal. The panel presented its interim proposals in August, 1981, recommending the diversification of coal import sources, extensive use of low rank coal, as well as enhanced international cooperation between coal producing and importing countries. THE CONTENTS OF THE COMMITTEE&apos;S REPORT Four Points for Major Consideration In order to ensure a stable supply of overseas coal, Japan needs adequate policy measures consistent with the characteristics of coal resources and environmental requirements, giving consideration to Japan&apos;s status and the role she is expected to play in the areas. From the above, great importance should be attached to the following four points: All the components of the "Coal Chain" (Namely, the development of mine sites, construction of railroads, port loading facilities, coal shipping vessels, port receiving facilities, including coal centers and international transport facilities etc.) should be reviewed and reformed with steps taken to assure efficiency consistent with the entire coal chain system. The complete formation of a coal chain system requires such lengthy lead times and huge amounts of investment that necessary measures should be undertaken well in advance utilizing long-range projections of future demands and various economic surveys. Policy planning should be conducted taking into account of harmonizing stability and economics of the supply structure. For ensuring the long-term stability and expansion of the coal trade, international cooperation on a bilateral and multi-national basis should be encouraged. Mutual understanding and close relationships are essential to facilitate the formation of the supply system and to promote the extensive use of coal. Direction and Problems Related to Supply Stability Expansion of Supply Capabilities. World coal imports in 1979 amounted to 229 million tons, of which Japan&apos;s share amounted to 59 million tons, or one fourth of the entire amount. The imports of European and Asian countries accounted for 83 million tons and 7 million tons respectively. According to the examination of the Investigative Committee, Japan&apos;s coal requirement is estimated to be between 140-150 million tons by 1990, nearly the same level as announced in the Provisional Long-Term Energy Supply and Demand Outlook in 1979. This fore¬cast is-to be revised in April, 1982. Japan&apos;s demand is expected to be met through fiscal 1985; however, by 1990, the supply is estimated to fall short of demand, particulary, in the field of steaming coal. For the expansion of supply capability, first, mine development should be accelerated. The proposed

Jan 1, 1982

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

[James C. Gray, President W. B. Stephenson, President-Elect A. B. Cummins, Past-President E. G. Fox, Eastern Regional Vice-President H. C. Weed, Western Regional Vice-President Donald W. Scott, Central Regional Vice-President John Cameron Fox, Secretary 29 W. 39 Street New York 18, N. Y. After September 7, 1961 345 East 47 Street, New York 17, N. Y. D. R. Tone, Assistant Secretary Nathaniel Arbiter, Treasurer]

Jan 1, 1961

[ ] [LOCAL SECTION CODE (Numbers indicate Sections) No. Section LI Alaska L50 Adirondack L2 Arizona L58 Arkansas L84 Balcones L66 Billings Petr. L3 Black Hills L4 Boston L76 Caracas L5 Carlsbad Potash L6 Central Appal. L60 Central N. Mex. L7 Chicago L79 CIM-AIME Calgary L82 CIM-AIME Edmonton L8 Cleveland L9 Colorado]

Jan 1, 1961

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa May, &apos;71.. 1 3 2. Bethlehem, I&apos;s Aug., &apos;71.. 110 3. Troy, N. Y Nov., &apos;71.. 113 4. Philadelphia, PaFeb., &apos;72.. 117 5. New York, N. YMay, &apos;72120 6. Pittsburgh, Pa Oct., &apos;72.. 125 7. Boston, MassFeb., &apos;73.. 128 8. Philadelphia, Pa.*May, &apos;73.. 23 9. Easton, PaOct., &apos;73.. 27 10. New York, N. Y Feb., &apos;74211] [ ]

Jan 1, 1925

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.&apos; The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--&apos;¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker&apos; on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski&apos; investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By A. J. McEvily, R. C. Boettner, C. Laird

The processes leading to fatigue failure in the low-cycle range were studied to obtain an understanding of the basis of Coffin&apos;s law. Particular attention was paid to the manner of mack nucleation and to the determination of the portion of the total lifetime spent in crack propagation. It was observed that cracks are nucleated at surface notches meated during reversed plastic deformation, Principally at grain boundaries, and that crack growth occupies greater than 75 pct of the fatigue life. When inclusions are present, they are often the primary sites of crack initiation. From consideration of the incremental distances advanced by a crack in each cycle and of the lifetimes of different materials, it appears that the universality of Coffin&apos;s law arises from the similarity of crack-tip strain for a given applied strain amplitude, irrespecti7:e of material. STUDIES of low-cycle fatigue have been particularly rewarding in that a simple correlation between fatigue lifetime and plastic-strain range has been shown to exist. This empirical relationship takes the forml,2 Nner=C [1] where N is the number of cycles to failure, Er is the plastic-strain range defined as the total plastic strain per cycle (the sum of the tensile plastic strain plus the compressive plastic strain), n, the exponent, is a constant independent of the material to a first-order approximation and often has a value of about 0.5, and C is a constant which for a number of ductile and metallurgically stable materials is approximately 0.65 for fully reversed strain.3 This relationship has been shown to be valid for a wide variety of metals and alloys and is often referred to as Coffin&apos;s law. However, it is yet not clear why so many different metals and alloys exhibit the same over-all behavior in the low-cycle range. Less is known about the mechanisms of fatigue failure in the low-cycle range than in the high-cycle range, but it is expected that the processes would have much in common. For example, an important characteristic common to both high-and low-cycle ranges is that fatigue crack propagation can occupy a considerable portion of the total lifetime. This has been shown by Laird and smith4 by a count of the number of ripples present on the fracture surface of copper specimens, each ripple corresponding to one cycle of load. On the other hand, some marked differences have been noted. For example, in copper,5 nickel, and aluminum4 there is a greater tendency for grain boundary cracking to occur as the strain amplitude is increased. The purpose of the present work was to study further the processes leading to fatigue failure in the low-cycle range and to obtain an understanding of the basis for the validity of Coffin&apos;s law. Particular attention has been paid to the manner of crack initiation and to the determination of the portion of total lifetime spent in crack propagation. MATERIALS A number of metals and alloys were tested, although more attention was focused on a particular few, once general trends had become apparent. Alloys were selected so as to investigate the effects of crystal structure, number of phases, stacking-fault energy, and impurity content. The materials in this grouping were: high-purity copper OFHC copper 1100 aluminum (commercially pure) 70-30 brass (Cu-30 wt pct Zn)

Jan 1, 1965