Search Documents

By E. C. Wright

The bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth edition of "The Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after I9I0 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blastfurnace capacity complementary to bessemer operations, combined with the availability of the' necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the -exense of besskmer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made, in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Re-phosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complee discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By F. N. Rhines, W. S. Pellini

In many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummerl have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium of experimentation. New values obtained in this way are believcd to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by X. S. Dean2 and by E. E. Schumacher and F. C. Nix. Their points are represented in Fig. I. In their work the solidus was not located at antimony collcentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228OC.; J. E. Stead,7 24g°C.; Campbell,8 228°C.; W. Gontermann,9 245' to 252°C.; R. Loebe,lo 245°C.; E. Heyn and 0. Bauer,ll 245°C.; H. Endo,12 250°C.; R. S. Dean,= 247' to 258°C.; E. Abel, O. Redlich, and J. Adier,13 245°C.; W. Broniewski and L. Sliwowski,14 250' to 252°C.; H. Seltz and B. De Witt,4 25o°C. A temperature of 247°C. appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 247°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1943

By W. S. Pellini, F. N. Rhines

In many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummerl have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium of experimentation. New values obtained in this way are believcd to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by X. S. Dean2 and by E. E. Schumacher and F. C. Nix. Their points are represented in Fig. I. In their work the solidus was not located at antimony collcentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228OC.; J. E. Stead,7 24g°C.; Campbell,8 228°C.; W. Gontermann,9 245' to 252°C.; R. Loebe,lo 245°C.; E. Heyn and 0. Bauer,ll 245°C.; H. Endo,12 250°C.; R. S. Dean,= 247' to 258°C.; E. Abel, O. Redlich, and J. Adier,13 245°C.; W. Broniewski and L. Sliwowski,14 250' to 252°C.; H. Seltz and B. De Witt,4 25o°C. A temperature of 247°C. appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 247°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1943

During the past 60 or 90 days, the metropolitan newspapers have published much concerning unemployment throughout the nation and the efforts of the Army and various other bureaus for finding work for the returning soldiers. The United States Employment Service has 2000 bureaus throughout the country, which Nathan A. Smyth, Assistant Federal Director, states have placed more than 2,400,000 persons in employment. The Engineering Societies Employment Bureau, which, since December, 1918, has been endeavoring to put all returning engineers in touch with employers who need efficient men, has produced results that are very gratifying to the Secretaries of the four Founder Societies under whose direct management the Bureau operates. During this period, 1615 men have registered at the Bureau's office in the Engineering Societies Building; not all of these, however, are unemployed. Many are ex-army and navy men, who in passing through New York on their way home, look over the field in the hope of making a change for their own benefit before returning to their former positions. During this period, 427 positions vacant have been filed, 2300 of which positions have been filled from the men registered. The letters mailed by this Bureau amount to about 1000 a month and the number of personal calls at the office, 1600. The lowest number of positions filled has been in mining, but the lowest number of registrations is also from mining men. While in February idleness throughout the nation was increasing at the rate of 35,000 a week, under date of Mar. 7, Arthur Woods, a special assistant to Secretary of War Baker, states that there is a material improvement in the unemployment situation and that the problem is no longer a serious one. It is recognized that' the improvement wrought in each individual by his military training and experience has so increased his value that it is 'not only unfair, to ask these men to accept their old jobs at the old wages, but it is probably very unlikely that they will be willing to do so. This plain statement of improvement may not carry conviction to everyone but a concrete example will show its validity. Take the example of a young man under 21, bright and intelligent, with only a high-school education who was employed, before being drafted, on purely manual labor. He shows up well under military training and is made a corporal; he makes good and is appointed a sergeant; and finally becomes top sergeant, which requires him in many ways to handle the entire company of 250 men. The result is; even if he has not been tried by the fire of battle, he comes out of the army with a feeling of self-confidence and capacity that was entirely lacking when he went in and he has had actual experience in handling a larger body of men than the average mine foreman at twice his age, and he has had twice the average amount of detail work to take care of.

Jan 4, 1919

By H. R. Nelson, Martin S. Maier

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1' and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By Martin S. Maier, H. R. Nelson

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1' and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By L. Burris, G. A. Bennett, P. A. Nelson

Staznless steels ave rrzuch less seuel-ely attacketl by zinc lapov than by molten zinc systems. To determine the applicubility of stainless steels fov equipment items which would be exposed only to zinc vapor, the corvosion resistance of several stainless steels to zinc vapor was investigated in 500-hr- exposuves at 900° C. Two austenilic stainless steels, Types 304 and 3-17, suffered severe intergranular attack. Loss of nickel from these steels and micro-probe crnalyses indicated the probable formation of low-melting zinc-rich phases. Good vesistance to attack by zinc vapor, as determined by metallo-9-rpaphic excr)rtination and physical testing, Loas exhibited by Type 405 stainless steel, a jevvitic steel. Type 440C stainless steel, a tnartensitic steel, although suffering considevable loss in weight, was not structurally weakened. At Argonne National Laboratory liquid zinc and zinc-rich alloys are being employed as solvent media in pyrometallurgical processes under development for recovering and purifying discharged reactor-fuel materials.' Because of the high solubility of most metals in liquid zinc,' there are few metals which can serve as container materials for liquid zinc at temperatures much above the melting point. The poor corrosion resistance of the common metals and alloys to molten zinc has been discussed by Eldred.3 DeKany, Lavendel, and Burris4 tested some of the less-common alloys of the nonrefractory metals and found that they also have poor resistance to attack by liquid zinc and Zn-Mg solutions. Of the metallic materials, only some of the refractory metals such as tantalum, tungsten, and molybdenum and their alloys have shown resistance to attack by liquid zinc.4-7 In the process-development work at Argonne National Laboratory, tantalum and tungsten vessels have been used to hold liquid-zinc alloys. These vessels are housed in stainless-steel equipment, principally to permit maintenance of an inert atmosphere and operation at various pressures. In this experimental work, it has often been observed that Type 304 stainless steel suffers little attack by zinc vapor at temperatures up to about 800 °C. In contrast, severe attack occurs in areas where zinc condenses as a liquid. The extent of attack by zinc vapor on several stainless steels was investigated because there are possible useful applications of stainless steel for equipment items which would be exposed only to attack by zinc vapor. These applications include, for example, housings around processing equipment as indicated above and vapor lines leading from zinc stillpots or retorts to condensers. EXPERIMENTAL EQUIPMENT AND PROCEDURE The experimental procedure consisted in exposing stainless-steel test coupons to static zinc vapor for 500 hr at a temperature of about 900°C. The apparatus, shown in Fig. 1, consisted of a 12-in.-long closed tantalum tube jacketed in Type 304 stainless steel to prevent oxidation of the tantalum. A Zn-10 wtpct Mg* alloy charge of 293 g in the bottom of the

Jan 1, 1965

By Sidney Fischler

Large striation-free single crystals of bismuth have been grown from the melt by rapid freezing. Zone-refined bismuth, together with doping impurities if desired, is placed in a shallow flat-bottomed graphite boat and melted in air with a propane hand torch. The torch is then withdrawn in a manner which causes the melt to freeze direction-ally. Crystallization, which resuires only a few minutes, usually results in the formation of a single crystal even when a seed crystal is not used. Crys -tals of any desired orientation may be grown by using oriented seeds. Undoped crystals grown by this method have residual resistivity ratios greater than 200. THE growth of large single crystals of bismuth by either the Czochralski or horizontal zoning technique is not entirely satisfactory. Specifically, difficulties are encountered in producing single crystals of the required dimensions in all desired orientations, and striations caused by low-angle polysynthetic twins are frequently present in the crystals. In addition, both methods are time-consuming and require special apparatus of some complexity. A simpler method has now been developed for growing large striation-free bismuth single crystals of desired orientation in a short time. Fig. 1 shows a typical setup consisting of a rectangular graphite boat which contains zone-refined bismuth, a 1/8-in.-thick flat quartz plate which covers the entire inner bottom of the boat, and three additional quartz plates about 1/4 in. thick which are used to separate the bismuth from the graphite everywhere except at a small area at the left of the boat. The graphite boat is 1 in. high, and its sides and bottom are about 1/8 in. thick. The quartz plates should be smooth and clean. The graphite boat is heated from the right with a propane torch, as shown in Fig. 1, until the bismuth is completely melted. The melt has the shape of a triangle with a narrow neck at the apex farthest from the torch. The melt is frozen direc-tionally by gradually moving the torch toward the right, away from the boat. The bismuth in contact with the graphite, at the left end of the neck, freezes first. The freezing interface then moves down the neck into the main bulk of material, where it develops a convex shape ideal for the continuation of single-crystal growth. The interface continues to move through the melt until the entire bulk is solid. The entire procedure may be completed, in air, in a matter of minutes. The technique described almost always yields a single crystal whose basal plane is nearly perpendi,cular to the bottom of the graphite boat. In earlier experiments, in which the bottom of the melt was in direct contact with the graphite boat, single crystals were grown with basal planes parallel, perpendicular, or at some intermediate angle to the bottom of the boat. At times the orientation of the bulk of the material differed from the orientation of the material in the narrow neck. In these cases, a nucleation site initiated the growth of a differently oriented crystal, and the thermal conditions favored the new orientation over the initial one. The thermal conditions depend on a number of factors, including the heating technique, the placement, shape, and thickness of the quartz plates, the thickness of the walls and bottom of the graphite boat, and the quantity of bulk bismuth employed. All of these factors, plus the initial orientation and the presence and effectiveness of nucleation sites, will determine the orientation of the final large single-crystal slab. When a crystal of specific orientation is desired, an oriented section of a rapid-freeze crystal is shaped by spark cutting and grinding for use as a seed. To grow a doped crystal, the desired impurity is placed in the graphite boat together with the bismuth chunks and seed. Crystals doped with mercury, cadmium, lead, and selenium have been grown. The rate of freezing is so great that the distribution coefficient of any impurity approximates unity. On a gross scale, therefore, impurities should be more homogeneously distributed in rapid-freeze crystals than in Czochralski or zoned crystals. Because of the possibility of constitutional supercooling, however, it is quite possible that impurities are not homogeneously distributed on a microscopic scale in the rapid-freeze crystals. Generally the single crystal slabs which have been prepared are initially 5 to 7 mm thick. Thicker crystals may be obtained by using one of these slabs as a seed. The slab is placed in a graphite boat resting on a large aluminum block, either air- or

Jan 1, 1964

By W. R. Hibbard

THE classical work on the electrical conductivity of alloys was carried out by Matthiessen and his coworkers1 in the early 1860's. He attempted to correlate the electrical conductivity of alloys with their constitution diagrams, but the information regarding the latter was too meager for success. Guertler2 reworked Matthiessen's and other conductivity data in 1906 on the basis of volume composition (an application of Le Chatelier's principle with implications as to temperature and pressure effects), and obtained the following relationships between specific conductivity and phase diagrams (plotted as volume compositions) : 1—For two-phase regions, electrical conductivity can be considered as a linear function of volume composition, following the law of mixtures. 2—For solid solutions, except intermetallic compounds, the electrical conductivity is lowered by solute additions first very extensively and later more gradually, such that a minimum occurs in systems with complete solid solubility. This minimum forms from a catenary type of curve. Intermetallic compound formation with variable compound composition results in a maximum conductivity at the stoi-chiometric composition. Landauer" has recently considered the resistivity of binary metallic two-phase mixtures on the basis of randomly distributed spherical-shaped regions of two phases having different conductivities. His derivation predicts deviations from the law of mixtures which fit measurements on alloys of 6 systems out of 13 considered. Volency (Ionic Charge) Perhaps the first comprehensive discussion of the electrical resistivity of dilute solid-solution alloys was presented by Norbury' in 1921. He collected sufficient data to show that the change in resistance caused by 1 atomic pct binary solute additions is periodic* in character. The difference between the period and/or the group of the solvent and solute elements could be correlated with the increase in resistance. Linde5-7 determined the electrical resistivity (p) of solid solutions containing up to about 4 atomic pct of various solutes in copper, silver, and gold at several temperatures. He reported that the extrapolated"" increase in resistance per atomic percent addition is a function of the square of the difference in group number of the solute and solvent as follows: ?p= a + K(N-Ng)2 where a and K are empirical constants and N and Ng are group numbers of the constituents. This empirical relation was subsequently rationalized theoretically by Mott,8 who showed that the scattering of conduction electrons is proportional to the square of the scattering charge at lattice sites. Thus, the change in resistance of dilute alloys is propor-t,ional to the square of the difference between the ionic charge (or valence) of the solvent and solute when other factors are neglected. Mott's difficulty in evaluating the volume of the lattice near each atom site where the valency electrons tend to segre-gate: limited his calculations to proportionality relations. Recently, Robinson and Dorn" reconfirmed this relationship for dilute aluminum solid-solution alloys at 20°C, using an effective charge of 2.5 for aluminum. In terms of valence, Linde's equation becomes ?P= {K2 + K1 (Z8 -Za)2} A where K1 and K2 are coefficients, A is atomic percent solute, Z, is valence of solvent, and Zß, is valence of solute. Plots of these data for copper, silver, gold, and aluminum alloys are shown in Fig. 1. The values of K1 and K2 are constant for a given chemical period (P), but vary from period to period. The value of K, increases irregularly with increasing difference between the period of the solvent and solute element (AP), being zero when AP is zero. The value of K, appears to have no obvious periodic relationship. All factors other than valence that affect resistivity are gathered in these coefficients. Because of the nature of the coefficients, Eq. 1 is of limited use in estimating the effects of solute additions on resistivity unless a large amount of experimental data are already available on the systems involved. It is the purpose of the first part of this report to investigate the factors that may be included in the coefficients of Linde's equation. On this basis, it is hoped that the relative effects of solute additions on resistivity can be better estimated from basic data, leading to a more convenient alloy design procedure. It is well 10,11 that phenomena that decrease the perfection of the periodic field in an atomic lattice, such as the introduction of a solute atom or strain due to deformation, will also increase the electrical resistivity. Thus, in an effort to relate changes in electrical resistivity to alloy composition, it appears appropriate to consider the atomic characteristics related to solution and strain hardening

Jan 1, 1955

By Martin S. Maier, H. R. Nelson

THE diffusion of metals plays an important role in many metallurgical processes, 1,2 as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystallization and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved.1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms-self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radio-activity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes-lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-10 and bismuth10 using natural radioactive isotopes, and of gold11 and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited on one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc, 14-16 silver,17 and copper.18 The second method was used for the work described in this paper. MATERIALS The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by 1/8 in. thick. Samples of high-purity copper described by Phillips and Skinner19 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By Nathaniel Arbiter

T. M. Morris (School of Mines and Metallurgy, Rolla, Mo.)—Rate studies promise to help quantify flotation operations. The author's exposition of rate studies is therefore laudable. However his exposition of a second order rate equation rather than a first order rate equation is not convincing. It is important to use the correct equation, otherwise erroneous conclusions may be drawn. The data assembled by the author and plotted according to a second order rate equation can be plotted according to a first order rate equation. As a matter of fact much of the data used reveals that a second order rate equation is not applicable. According to the method used by the author for plotting data, the reciprocal of the slope of the line is the maximum possible recovery. Physically this cannot exceed 100 pct, yet several graphs yield maximum recoveries greater than 100 pct. For example: l—Curve 2, Fig. 1 yields a value of 120 pct; 2—Curve 2, Fig. 2 yields a value of 115 pct; 3—Fig. 7 yields a value of 110 pct. The real test of the graphical method is, as the author points out, whether or not the earliest points agree with a straight line. The second order rate plot does not fulfill this requirement. Fig. 10 shows the data used by the author to obtain Curve 2 in Fig. 1, plotted according to both a second and first order rate equation. Fig. 11 shows the two rate plots made from data published by Ludt and DeWitt.19 In Fig. 10 the first order rate plot gives a very good fit and obeys the boundary condition of passing through the origin. For the second order rate plot a straight line can be drawn through the last three points but the earliest points are not in agreement with this line. The reciprocal of the slope of the straight line gives a value of maximum possible recovery of 112 pct. The maximum possible recovery according to the first order rate plot is 78 pct. In Fig. 11 the first order rate plot again fits all of the points very well and passes through the origin. The second order rate plot shows wide deviation of the earliest point, indicating that the second order rate equation is not applicable. The reason for the fit of data to the second order rate equation during longer flotation times is that R, the cumulative percent recovery, changes slowly toward the end of the flotation operation, so that when t/R is plotted against time, one is, in effect plotting t against t and one would certainly expect a straight line. The author attempts to show that the second order rate equation is correct by citing evidence which shows that recovery is a function of initial concentration. This is a debatable point especially since, in the author's original presentation of this paper at the St. Louis

Jan 1, 1952

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

Alabama.1 Arizona 1 Arkansas 2 California 2 Colorado 7 Connecticut 8 Delaware 9 District of Columbia 9 Florida 10 Georgia 11 Idaho 11 Illinois 11 Indiana 13 Iowa 14 Kansas 14 Kentucky 14 Louisiana 15 Maine 16 Maryland 16

Jan 1, 1952

By Frank Gilbreth

THE problem, of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community, without placing the cripples into competition with any existing class of workers.

Jan 4, 1918

Discussion of the paper of C. W. Goodale and J. H. Klepinger, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 50, August, 1913, pp. 1935 to 2010. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Chairman, I would like to call attention to one valuable feature of the paper which may interest some: I have worked a good deal with the Pitot tube, and have always had difficulty with what is called the static end of that apparatus, so much so that I became almost hopeless of securing good results with it. I find here, however, what is stated to be a perfectly satisfactory static end for the Pitot tube, satis factory under probably all conditions. I congratulate Mr. Klepinger on the design of that tube and the consequent improvement he has made in the technical measurement of the volumes of gases. I would also like to ask if the total volume coming out of the chimney per day could not be computed by chemical analyses of the SO and SO2 in the gases, and calculation on the basis of the known weight of.. sulphur going out in a day; so that the Pitot tube measurements . could be checked by a method independent of measurements in the flues. J. H. KLEPINGER :-I think the volume of gases could be determined in that way. Those of a chemical turn of mind would go. about it so, but I am not enough of a chemist to follow that method, and consequently I always look at the mechanical way to obtain the results.

Jan 11, 1913

By Ralph H. Kress

Haulage trucks designed expressly for mine service were introduced about 35 years ago. The first models to arrive on the scene hauled about 15 tons and easily outperformed the modified highway trucks that had been used for mine haulage up to that time. The specialized trucks obviously had a greater potential for mining operations, and once this fact was recognized, competitive pressures in both the mining and truck-manufacturing industries drove the new vehicles toward ever more efficient performance. Many changes in truck design resulted, but not all were accepted for a variety of reasons. Often poor design was the reason, but in many cases progressive and promising designs were abandoned only because the truck manufacturer lacked the courage, tenacity, or vision to capitalize on them. There were also many cases where a promising new design was abandoned because the prototypes were initiated in a mine where personnel lacked the patience to prove them. Truck Startup Takes A Team Ally new truck that is to succeed and contribute to lower mine haulage costs must be well conceived and launched with good teamwork on the part of all concerned. Naturally, it is essential to have a good overall truck design at the outset to make this teamwork worthwhile. The design must include the selection of the right components manufactured by suppliers that can each do justice to their particular part of the new truck. Last, but by no means least, the mine operator where the truck is to be launched must be enthusiastic in his efforts to see the new vehicle through to successful operation.

Jan 1, 1971

By Donivan L. Gordon, Fred H. Dorheim

Often, as viewed by the public and many in the mining industry, abandoned limestone and gypsum quarries offer a simple, economic solution to the twofold problem of solid-waste disposal and land reclamation. In a state where about 75% of the existing quarries are in hydrologic connection with carbonate aquifiers the rationale for considering the storage of solid waste in them must be critically examined. Consistent with the requirements of water resources protection, criteria are suggested to evaluate the potentiality of using abandoned limestone and gypsum quarries as sanitary landfill sites.

Jan 1, 1975