Search Documents

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

By R. L. McCarron, G. R. Belton

The diffusivities of oxygen and sulfur in liquid iron have heen determined hy a capillary technique in which the surface concentrations of the solutes were established by means of appropriate H2/H2 and H2S/H, gas mixtures. Total diffusate and concentration profile results are shown to be in good accord, yielding for- 1560 and Supporting results at 1660°C are also presented. The conditions necessary to avoid gas transport control in this type of experiment are discussed. IN spite of their importance in understanding the kinetics and mechanisms of refining reactions, the dif-fusivities of oxygen and sulfur in liquid iron are not well established. Accordingly, as a first step in studies of rates of solute absorption from the gas phase into liquid iron, new measurements of these diffusivities have been made and are presented in this paper. The only published results for the diffusion of sulfur in pure liquid iron are those of Kawai.' He used a diffusion couple technique in which two cylindrical specimens, one containing sulfur and the other with negligible sulfur concentration, were joined together and held in a refractory capillary. After an experiment, the sample was quenched and the concentration distribution of the solute determined. Kawai recognized that significant changes in solute distribution occurred during melting and freezing and he attempted to correct the concentration profiles for these effects to give a sulfur diffusivity of 4.6 x 10-6 sq cm per sec at 1560°C. The method of correction, however, was not rigorous and the uncertainty in this result cannot be easily assessed. Koslov et a1.2 have reported the diffusivity of oxygen in iron as 7.8 x 10"3 sq cm per sec at 1660°C. This value appears to be unreasonably high but, unfortunately, details of their experiments are not available. Shurygin and Kryuk have used the rotating disc method for a study of oxygen diffusion in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was determined by measuring the decrease in weight of the disc. On the assumption that the rate of dissolution was controlled by the diffusion of oxygen in the iron, the diffusion coefficient was computed to be 5.2 x sq cm per sec at 1550°C. However, the Levich equation, which was used to interpret the rate data, was originally de- rived for the case of mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich's equations. Recently, Novokhatskiy and Ershov, using an identical experimental method to that of Shurygin and Kryuk, obtained a diffusivity for oxygen in liquid iron of 1.22 x 104 sq cm per sec at 1550°C: no reasons were offered for the disagreement. Schwerdtfeger5 has also recently studied the diffusivity of oxygen in liquid iron. He reacted shallow melts of liquid iron, 0.5 to 1.0 cm deep and contained in high-purity alumina crucibles, with appropriate H20-HZ-He mixtures. The total sample was analyzed, without sectioning, to obtain the average concentration of diffusate. A value at 1610°C of D = 12(3) x 10-5 sq cm per sec was obtained from the results of twenty experiments.= Oxygen profile measurements, which were carried out in three additional experiments using long capillaries and the semiinfinite boundary conditions, indicated a diffusivity about half that computed from the shallow bath experiments. Possible sources of error in Schwerdtfeger's study will be discussed later in this paper. EXPERIMENTAL TECHNIQUE The essential arrangement of the diffusion cell is shown in Fig. 1. The liquid iron was contained in an alumina capillary, 3 to 4 mm diam and 3 to 9 cm long, which was supported by a hollow alumina pedestal and this whole assembly was held within a movable alumina reaction tube. This tube, which was about 7 mm in bore

Jan 1, 1970

By T. Seldenrath

In the development of a fluid -operated hammer drill' for accelerated penetration of hard rock formations in oil wells, a research investigation was conducted to evaluate the percussion effects obtained with different design characteristics and to determine the possibilities of percussion in the low frequency range. Tests were conducted on granite blocks and comparable impact forces were measured with a load cell under selected test conditions. These full-scale laboratory tests provided an evaluation of the effectiveness of percussion which was further supported by actual downhole field performance. While much pertinent data have been presented by other investigators the method of evaluation described in this article resulted in good correlation between laboratory and field performance and may be applicable in other low frequency percussion developments. EXPERIMENTAL METHOD For these tests the bit was held stationary and the test block was rotated and forced upward against the bit by a hydraulically-lifted rotary table. "Weight on bit" was calculated from pressure readings on the fluid system of the lifting cylinders—corrected for tare and friction. Percussion was obtained with several tubular hammers of different weights up to 320 lb. These were lifted mechanically and allowed to drop by gravity from various heights onto a slidably-mounted bit sub or "floating anvil" for calibration of the load cell response with known kinetic energy of the hammers. During evaluation of percussion effects, the hammers were hydraulically operated to provide a range of percussion frequencies up to 1,020 blows per minute delivered to the anvil. To obtain comparable test readings, the load cell of the strain gauge type, was attached to the bottom of the anvil or bit sub in place of the bit. The load cell rested on a typical granite test block mounted on the drilling table. The latter was hydraulically supported as in the actual drilling operation. The effect of support resistance was the same for all tools when calibrating. Impact forces so determined werethusdirectly comparable with one another for the purposes of this investigation. When a roller bit was substituted for the load cell for actual drilling, the impact force would probably be reduced due to the resiliency of the bit body, legs. cones and teeth and the penetration of the teeth into the rock. However, since the bits and rock specimens were uniform in these tests, an evaluation of actual tool performance, in terms of parameters previously determined with the load cell at the selected standard conditions of calibration, proved satisfactory. Throughout these tests, 8¾-in. standard tricone, hard rock toothed roller bits and carbide-insert roller bits were used. Rotary speeds were 50 and 100 rpm; static weight on bit was applied up to 40,000 Ib, and percussion frequencies up to 1,020 blows per minute were available. During this investigation it was found that toothed bits on which the teeth had developed flat ends about 3/16 in. wide did not change appreciably for the duration of a test. Hence, all toothed bits used in this study were in this condition. Conventional reference curves obtained in these tests show that increasing weight on hit by 2:1 yielded an increased penetration rate of approximately 2.7:1, while an increase in rotary speed of 2:1 netted an increased penetration rate of roughly 1.7:l. Results are thus of the same order as those reported for hard rock drilling by other investigators." CALIBRATION Under the selected standard test conditions previously described, with the lifting table hydraulically supported, and the anvil interposed between hammer and load cell, the hammers were dropped from known heights. Thus, with the kinetic energy of the hammer known, the corresponding maximum impact force shown by the cell was determined. (It may be of passing interest to note here that special drop tests with the hammers showed that no appreciable reduction in impact force resulted from introduction of the anvil or hit sub.) From these calibrations, it was possible to determine the theoretical kinetic energy available in the hammer from the maximum impact force shown by the load cell while operat-

By D. A. Elgillani, S. Atak, D. A. Rice, M. C. Fuerstenau, R. B. Bhappu

Quartz and feldspar cannot be floated with sulfonate at any pH; spodumene floats over a narrow acid pH range, while beryl responds moderately over a broad pH range. After wet-grinding in a steel mill, beryl, quartz, and spodumene float well with sulfonate below about pH 7, whereas the improvement in the response of feldspar is not so marked. A mechanism by which iron can be adsorbed on these minerals is presented. Also, the responses of leached, natural, and wet-ground beryl to amine, sulfonate, and oleate flotation are shown and related to the measured zero-points-of-charge of these materials. Earlier work with leached beryl showed that good flotation could be obtained with alkyl aryl sulfonate over a rather wide pH range using a Fagergren flotation cell.' When a similar response was observed with leached quartz, it was decided that unintentional activation was being obtained from the metallic components of the Fagergren cell. To obviate this difficulty, a microflotation cell was designed, and an experimental technique was devised. These have been described elsewhere. Experiments conducted with the small cell showed that leached quartz could not be floated at any pH with any sulfonate addition,3 which is in agreement with the observations of Kraeber and Boppel.4 Similarly, it was also found that leached beryl responded to sulfonate flotation only over a narrow pH range rather than the broad range reported earlier.1 This early work,1 however, revealed the important effect that wet-grinding in a steel mill has on the flotation response of certain silicates. That is, it was found that quartz and especially beryl floated well over an unusually wide pH range after wet-grinding in a steel mill. Microcline, however, floated poorly below pH 4, even though wet-ground under the same conditions. The work of Eigeles6 on adsorption of oleic acid on leached quartz and iron-contaminated quartz at constant pH is in agreement with these flotation data. Other research has shown that ferric iron, added as a salt to the system, functions as an activator in the narrow pH range in which Fe +++ iron hydrolyzes to its hydroxy complexes.3,5 These phenomena indicate that iron functions differently in flotation systems depending on its method of introduction. The object of this paper is to determine the mechanism by which iron is adsorbed on certain minerals, the mechanism of collector adsorption after iron abstraction, and the role that Fe++ and Fe+++ assume in the selective separation of these minerals. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate, mol wt 450,7 pure potassium oleate, and pure dodecylamine were used as collectors. All other chemicals were reagent grade in quality, i.e., n-amyl alcohol as frother; HC1, H2SO4, and KOH for pH adjustment; and ferric chloride as activator. Conductivity water, made by passing distilled water through an ion exchange column, was used in the experimental work. All minerals used in the investigation were hand-picked specimens. Sample Preparation: Each of the minerals was crushed through 8 mesh, and the product was divided into two groups, one to be ground dry and the other wet. Dry grinding was accomplished with an alumina mortar and pestle. The product was dry-screened to 48 x 150 mesh, cleaned magnetically, deslimed in conductivity water, and dried. Preparation of the samples by wet-grinding involved grinding a 200-g charge of the mineral (-8 mesh) at 60% solids with natural water in a mild steel rod mill for four minutes. This charge was then wet-screened immediately with natural water to 48 x 150 mesh, dried, and cleaned magnetically. Some experiments were also conducted with leached beryl and quartz. These products were prepared by leaching the sized sample (48 x 150 mesh) with concentrated HC1 with a percolation technique until no iron could be detected in the leach liquor. Following this step, the sample was rinsed with conductivity

Jan 1, 1967

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By V. F. Hollister

The Queen Charlotte gold deposit (also known as the Specogna, Babe, or Cinola) was discovered in late 1970 by Efrem Specogna and Johnny Trico. They were prospecting along the trace of the Sandspit fault, and they sampled jarositic material that included veins from the fault zone. Their assays included some good gold values. They located the Babe Claims in 1971 and optioned them to Kennco Explorations Ltd. Kennco conducted stream sediment and soil geochem studies, geological mapping and drilling of 55.2 m (181 ft) in two drill holes. Kennco withdrew from the property, and by 1977, Cominco, Placer Development, Silver Standard, and Quintana Minerals had each successively worked on the deposit. Consolidated Cinola Mines bought the claims in 1977 and completed exploration of the deposit ultimately in a joint venture arrangement with Energy Reserves. Energy Reserves entered in late 1979, and by 1983, a total of 200 surface and 12 underground drill holes had been completed, totaling 28 600 m (93,832 ft). In addition, a 461.9 m (1515 ft) adit was driven in the ore body. Reserves published by Cinola aggregate 34 Mt (37 million st) of 1.7 g (0.060 oz) Au per tonne. All industry geologists working in the area agree that the Queen Charlotte gold is an epithermal gold deposit in porous volcaniclastic and clastic rocks that is genetically related to a Miocene-Pliocene rhyolite plug. The geologic description here follows the oral presentation made by G. G. Richards, J. S. Christie, and M. R. Wolfhard at a 1976 CIM meeting. Additional comments by the late C. S. Ney of Kennco Explorations are included with the Richards, Christie, and Wolfhard data to complete the geologic set- ting. The attached reprint by Champigny and Sinclair (1 980) provides additional data on the deposit. The Queen Charlotte (Babe, Specogna, or Cinola) gold deposit is located on Graham Island in the northern Charlotte Islands, at the fault boundary of the Skidegate plateau and the Charlotte lowlands. The Sandspit fault marks the physiographic boundary, and it is intruded by rhyolite porphyry at the deposit. Because displaced geochem anomalies, drain- age patterns, and topography suggest dextral and east side down movement for the fault, exposed east block rocks are younger than rocks west of the fault. The east block, which included the ore deposit, is a lowland largely masked by unconsolidated Pleistocene and Recent clastic rocks. Rocks west of the rhyolite plug, on the Skidegate plateau, are Cretaceous carbonaceous and calcareous shale unconformably overlain by a thin veneer of rhyolite tuff. The deposit is about 100 m (328 ft) above sea level. GEOLOGIC SETTING At the ore deposit, the Sandspit fault is a complex structure. However, lithologies on either side of the fault-controlled rhyolite porphyry plug are distinct. West of the rhyolite, the upper member of the Cretaceous Haida formation shale is the most common rock type. The member is composed of dark grey to black, poorly consolidated, and thinly bedded carbonaceous and calcareous shale. The sequence is silicified to an argillite or a hornfels near the rhyolite. West of the rhyolite porphyry plug, but not importantly involved in the mineralization, is a thin masking cover of rhyolite tuff. The tuff unconformably succeeds the cretaceous shale, but it is largely eroded in the mine area. East of the fault-controlled rhyolite porphyry plug is a thick section of conglomerate and sandstone of the Miocene- Pliocene Skonun formation. The ore body occurs within the coarse clastics, the rhyolite intrusive as the western boundary. Ore is entirely contained within the clastics. Original permeability of the clastic rocks was a major control for ore deposition and alteration, and for that reason, the Skonun formation is described in greater detail. The Skonun formation clastics unconformably overlie Haida shale. The Skonun is at least 300 m (984 ft) thick in the mine area, where it trends northerly and dips easterly 15º to 25º. The sequence is about 62 percent conglomerate, 3 1 percent coarse arkosic sandstone, and 7 percent interbedded siltstone and sandstone. Contacts between adjacent beds are generally sharp. Stratigraphic correlations between drill

Jan 1, 1985

By P. R. Celmer, Leonard R. Weisberg

THE principle of fractional crystallization has been successfully used to prepare high-purity (99.999 pct) Ga. Hoffman and Scribnerl removed single crystals of gallium solidifying in a gallium melt, while Zimmerman2 grew single crystals from the melt by the Kyropolous technique. In contrast, attempts at purifying gallium by zone refining have been less successful. ichards, reported that despite the passage of 40 zones through a gallium ingot, there still remained 5 to 70 ppm each of Cu, Fe, Ca, Mg, Si, Al, and Ag. Previously, Detwiler and Fox4 detected only one impurity, Pb, segregating in zone-refined ingots. These surprising results prompted an investigation of the factors controlling impurity segregation in gallium. Possible reasons for this were insufficient diffusion of impurities in the melt; recontamination of the melt by its oxide film which is not affected by the passage of the zone; reaction of gallium with the boat; sudden freezing of gallium following supercooling, especially since gallium easily supercools to and trapping of impurities at grain boundaries. Impurity segregation tests were carried out by directionally freezing gallium using the Bridgman rnethd, modified in that the molten gallium is lowered out of a furnace into a slush of dry ice and trichloroethylene, thus minimizing supercooling. Since the gallium is contained vertically, the oxide film is in contact only with the tail end of the melt. It was found that Teflon makes an excellent crucible for gallium since it is quite pure, non-reactive, translucent, flexible, machinable, and is not wet by gallium. The gallium crystals could be grown at various speeds, and the melt could be vigorously stirred by a Teflon rod moving through the gallium in a vertical reciprocating fashion. Single crystals could be grown by placing a solid Teflon plug at the bottom of the melt drilled out in such a way to cause the solidifying gallium to follow a winding path. Thus, even if many crystals are originally nucleated, only one grain will predominate. The grain structure of the gallium crystals was revealed by an etchant composed of equal volumes of HC1, HNO3 and HF, diluted with water to half strength. Emission spectrographic analyses were carried out on samples removed from the front and tail ends of the resulting gallium ingots. Typical results of this study are summarized in Table I. The rate of freezing in all three cases was about 1 in. per hr. It can be seen that even though stirring of the melt does help, it is even more important to grow a single crystal of Ga in order to obtain good segregation of impurities. The effect of crys-tallinity on the segregation of impurities was previously observed6 in the directional freezing of germanium; however, in this case, the effect was much less pronounced. This dependence of impurity segregation on the crystalline perfection of Ga may be related to its thermal conductivity which is the most anisotropic of all metals.7 The anisotropic thermal conductivity can cause the solid-liquid interface to be nonuniform, thus leading to trapping of impurities during freeing, and therefore reduced segregation. In conclusion, it is indicated that zone refining of gallium would be more successful if seeding and similar precautions are taken to insure single crystal growth. The authors are indebted to Mr. H. H. Whitaker for the spectrographic analyses and to Drs. B. Abeles and F. D. Rosi for helpful advice and encouragement throughout the course of this work. This research was supported by the Electronics Research Directorate, Air Research and Development Command, under Contract No. AF33(616)-5029. REFERENCES 'J. 1. IToffmon and B. T. Scribrer: I. Research h'atl. Bur. Standards, 1935, "01. 15, p. 205. 'W. Zirnmerman: Science, 1954, vol. 119, p. 41. %J. L. Richards: Nature, 1956, vol. 117, p. 182. 'D. P. Detwiler and W. M. Fox: I. Metals, 1955, "01. 7, p. 205. 5P. W. Bridgman, Proc. Am. ilcod. Sci., 1925, vul. 60, pp. 305,385,423. "S. L1. Christian: private c ommuni cation. 'K. W. Powell: roy. Sac., 1951, vol. 209, p. 525. 'W. G. Pfann: Zone Re fining, p. 20. John Wiley and Sons, Inc., New York, L058.

Jan 1, 1962

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By Edwin H. Olson, Morton Smutz, Charles J. Baroch

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.1 The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district's gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct ThO2, 25 to 35 pet calcite, 10 pet rare earth oxides, 15 to 20 pet silica, and 30 to 40 pet barite.2 Rare earth content of the ore analyzes 50.7 pet CeO2, 4.2 pet Pr6O11, 11.7 pet Nd2O3, 1.3 pet Sm2O3, and 34.3 pet La2O3, and others.2

Jan 3, 1959

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By J. Federico Price, Joseph E. Aparicio

This paper describes the production of a specific iron oxide pellet that has given very good and consistent results as feedstock for HYC-Process Direct Reduction Plants. The sponge iron originated from these pellets has been used for the economic production of almost 15 Mt of low carbon steel via electric arc furnace meltshops. An overview of mining, beneficiation, pelletizing, direct reduction and steelmaking for this case is given with emphasis on the charactertitics of the self-fluxing oxide pellets.

Jan 1, 1982

By H. E. Cook

The Ising model for the internal energy of a binary alloy has been used to obtain a general equation for the critical resolved shear stress of partially ordered crystals. The equation expresses the stress in terms of the Warren "alphas " and can be used to estimate the variation in strength with order without the assumption, present in the original formulation of this problem in terms of domain size, that order is complete within each domain and that the domains are of ungorm size and shape. In addition, it is the general equation, according to the Ising model, for strengthening by short-range order. Two applications of the equation are considered: One is an estimate of the variation in strength of CkAu with long-range order. The other is an estimate of the variation in strength of FeCo with quench temperature. Reasonable agreement is found with the variations reported in the literature. When the internal energy of an alloy crystal depends upon the distribution of solute, the strength of the crystal will also depend upon it because a portion of the applied stress for plastic deformation will be: where V is the volume of the crystal and E(E) is the energy change associated with the solute redistribution caused by the plastic strain, E. We expect T to equal zero for a crystal having a random arrangement of solute because the arrangement would remain random after plastic deformation. Likewise, we expect it to equal zero when the crystal is perfectly ordered because the motion of paired dislocations found in such crystals does not disrupt order. However, when short-range order exists or when long-range order is incomplete, plastic deformation will decrease the amount of order and additional work, proportional to the ordering energy, will be expended. Fisher' estimated T for crystals having short-range order by assuming an interaction energy between neighboring atoms and estimating the change in the number of unlike neighbors as a dislocation moved through the crystal. (His analysis was limited and several workers2"6 have since given more complete ones.) Fisher minimized the importance of a strengthening mechanism of this type for paired dislocations in a structure having long-range order. ~ottrell,' however, pointed out that T could be appreciable for ordered crystals having antiphase domains. He attributed the strengthening to the increase in surface energy of the domains as they were cut by paired dislocations. Ardley,' in his test of Cottrell's theory, found that r for Cu3Au crystals obeyed the equation: for 1 > t where 1 is the domain size, t is the domain wall thickness, and y is the surface energy of an antiphase boundary. His experiments represent the classic confirmation of the strengthening mechanism proposed by Cottrell. However, the assumptions involved in using Cottrell's theory are valid only for large domain size in CU~AU,~"~ i.e., when Eq. [2] reduces to: For small domains, ~linn~ has questioned Ardley's assumption that order was complete, and, indeed, Stoloff and ~avies" fpnd it incomplete until a size of approximately lOOA was reached. Even when the order within a domain is complete, it is not obvious how one determines the appropriate value for I in a structure where domains vary in size and are irregularly shaped. The purpose of this paper is to estimate T without restrictions upon the degree of order and domain shape. Our major assumption will be the use of a generalization of the model proposed by Bethe" (the Ising model) for the internal energy. This will in fact allow us to combine the theories for strengthening by short-range order and by antiphase domains into a single, general formalism. We will use the results to estimate the variation in strength of Cu3Au crystals with long-range order8 and the variation in flow stress of FeCo crystals with quench temperature.12'13 INTERNAL ENERGY For simplicity, we restrict our considerations to those binary solid solutions which can be described as an arrangement of atoms on a Bravais lattice. An atom site will be indexed by three numbers (PI, pz, p3) determined by the vector: from the origin fixed at atom (0, 0, 0) to the atom site where a', an, and a, are the lattice translation vectors. We write: For the energy of the crystal where pi(p) is the probability (either zero or one) of finding an atom of type i (i = 1, 2) at site (p), which is shorthand for (pl, pz, p3) and pj(p + r) is that for an atom of type j (j = 1, 2) at the site (p + r), which is shorthand for (pl + rl, The coupling parameter, resents the energy associated with the pair Pi(p), Pj(p + r). The crystal is assumed large enough so that surface effects can be neglected; therefore, trans-lational and inversion symmetry require the coupling parameters to obey the relations

Jan 1, 1969

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By J. H. McCarthy, J. M. Botbol, R. B. McCammon, G. H. Gott

Four areas have been identified as favorable drill site locations for determining whether a suspected porphyry copper deposit exists in Rowe Canyon, NV. Favorability is bated on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for zinc, silver, aresenic, antimony, and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1983

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs' = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors' reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By A. C. Veatch

Jan 1, 1921