Search Documents

By K. R. Weller

The Ardlethan Tin Ltd. concentrator typically recovers 55% of the tin in a gravity concentrate at 51% grade from fresh ore assaying 0.5% Sn. Coarse gravity concentration is performed in a complex circuit involving Reichert cones, spirals, shaking tables and two regrind mills. The paper describes how flow and size-by-size sample data from a steady-state survey were used to construct a computer model of the plant involving 46 process streams. The data reduction involved a computer- aided mass balancing technique, recovery-size modelling of gravity concentrators and the use of a mineral dressing flowsheet simulator. The model was used to simulate possible rearrangements of the available equipment. Early simulations indicated that improved performance could be obtained by using spirals to-treat cone middlings or tailings rather than cone concentrates. A test spiral rig was used at Ardlethan to determine typical performances for all cone product streams and the results were incorporated in new simulations. A revised circuit was recommended and implemented by Ardlethan Tin as far as physical restraints within the plant would allow. Production figures show that a substantial increase in tin recovery and 10-15% increase in milling rate were achieved following the circuit changes, and these improvements were sustained over a six month period.

Jan 1, 1984

By J. P. Norris, W. T. Pettijohn

The Mufulira Copper Mine, Ltd., is in Northern Rhodesia, ten miles from the Belgian Congo border, and is one of the group of four operating mines comprising the Northern Rhodesian Copperbelt. The ore deposits at Mufulira are on the limb of a large syncline striking NW.-SE. and dipping NE. at about 45 deg towards the Congo border. The host rocks are well-consolidated, highly-silicified, felspathic quarzites of the lower part of the pre-Cambrian Séries des Mines of the Katanga. The ore rocks are underlain, unconformably, by the older "Muva Series," in this case hard, green, metamorphosed quarzites. There are three superimposed orebodies, the first, or upper, orebody averaging 40-ft true thickness with a strike length of about 5000 ft, the second, or middle, orebody of about 50-ft true thickness with a strike length of about 6000 ft, and the third or lower orebody of around 60-ft true thickness with a strike length of 8000 ft. The orebodies are separated by varying widths of waste, or very low-grade ore, from a few feet up to 50 ft. The middle and lower orebodies are so close together for a strike length of 3000 ft that they are mined as one orebody. In all, the mineralized zone is about 200 ft in true thickness.

Jan 6, 1950

ASIDE from the John Fritz Medal, in which the Institute partici¬pates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as fol¬ lows the Robert W Hunt Medal and Prize, the J E. Johnson, Jr , Award, the James Douglas Medal, and the William Lawrence Saun¬ders Medal ROBERT W HUNT MEDAL AND PRIZE The partners of Robert W Hunt established a fund which was, presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded tinder the following rules¬ 1 The award shall consist of two prizes first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member' over 40 years of age, but under unusual circumstances, both prizes may be allotted to one per son provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on non and steel The scope of the term "iron and steel" shall be determined by the sub-committee consideing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main con¬ti ibutions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

By Clifford J. Lewis, James L. Drobnick

Vexed with competition from relatively high grade foreign orebodies, perplexed by marginal, low grade domestic orebodies, and ironically faced with the fact that practically every metal needed in our economy is available domestically in ample quantity in the ground, our mining industry awaits the advancements in beneficiation technology that will bridge the gap between the ground and the market place for our presently unexploited mineral reserves. Among the vast number of research and development projects underway in the metals mining industry, there are a few chemical techniques in metals winning that, with further development or wider application, could have a profound effect on the industry. These techniques include the Imperial Smelting and Refining Process for complex lead-zinc ores, chlorination and fused salt procedures, the liquid ion exchange process, and the field of non-aqueous leaching. IMPERIAL SMELTING PROCESS The Imperial Smelting and Refining Process is of interest because it offers a possible economic route for the processing of complex zinc-lead-copper ores. The process represents the outcome of the combined efforts of metallurgists and engineers of Imperial Smelting Corporation. Ltd., the United Kingdom Subsidiary of the Consolidated Zinc Corporation, Ltd., and is the subject of patents throughout the world. This process is essentially the employment of the blast furnace for the production of zinc. Zinc has always resisted blast furnace technology, primarily because of the difficulty of condensing zinc vapor from dilute gases. The Imperial Smelting Process employs a blast furnace working at ordinary pressures and in a system which is able to con- dense a blast furnace gas of a very low zinc content.

Jan 11, 1963

By D. W. Fuerstenau

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed, and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped down, a period of 1 hr or so is required. When a disturbance in the feed rate was made, the transient period extended to more than 1% hr (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content

Jan 1, 1983

By A. F. Frederickson

A MINERAL can best be defined as a phase,' where the term "phase" is described as a homogeneous,* physically distinct, and mechanically sep- arable portion of a system. If one phase develops from another, certain nuclei must first be available.2.394 The manner in which new material is added to these nuclei, and the subsequent structural and other characteristics of the phase, is often markedly influenced by factors other than its temperature, pressure, and gross compositional environment. Rates of growth, presence of impurities, the availability or lack of oxygen, the pH of the system, and percentage of completion of the often determine which modification will develop. Many transitional phases develop when a relatively insoluble precipitate is formed from solution. Different modifications are formed, depending on the speed and percentage of reacting solution added. Some of these "forms" are stable and do not "age" or transform into the so-called stable modifications. These modifications are difficult to treat in terms of equilibrium diagrams for the simple reason that these minerals do not represent an equilibrium situation described by only two (temperature and composition) or three terms (when pressure is considered). Many crystals exist as stable or meta- stable phases in nature in environments much different from those indicated by certain equilibrium diagrams. Cristobalite octahedra grow on zeolite needles in vugs, diaspore develops from a medium that does not appear to have been subjected to high pressures and temperatures, authigenic feld-

Jan 1, 1952

By James Gardner

IN 1923, Oklahoma took second place as an oil-producing state; whereas in 1922 it was the leader. California surpassed it, in 1923, by nearly 100,000,000 bbl. In 1923, Oklahoma produced, according to statistics of The Oil & Gas Journal, 165,013,685 bbl., or an increase of approximately 10 per cent. over the preceding year; the increase in California was approximately 90 per cent. The number of wells drilled in Oklahoma and the results of the two years are contrasted in the following table from data published in a preliminary bulletin by the U. S. Geological Survey. 1922 1923 Oil wells 4,149,68%. 3,515, 60% Gas wells 571, 9 %u 587, 11% Dry holes 1,428,23% 1,731,29% Total wells 6,148 5,833 The initial production from wells drilled in Oklahoma in 1923, according to The Oil & Gas Journal, was the largest in the history of the state, being 1,277,936 bbl. It has been 32 years since oil development began in the state, last year being the largest in the amount of production. The production of the past year would have been considerably greater were it not for the shutdown order in the Burbank field and curtailment of production in the Hewitt and Tonkawa pools.

Jan 3, 1924

R. B. BRINSMADE, Puebla, Puebla, Mexico (communication to the Secretary*) :-As I have previously considered the general equations for mine-valuation,1 I will here discuss only that part of Mr. Finlay's paper criticized by E. E. White, along with some of the general principles of mining taxation, under the following six topics: 1. Rate of interest earned by sinking-fund. 2. Rate of interest earned by investment. 3. Place of royalty item in valuation. 4. Place of taxation item in valuation. 5. Calculation of future ore-prices. 6. Valuation of undeveloped mining land. 1. Rate of Interest Earned by Sinking-Fund.-Mr. Denny's quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer war. The great destruction of liquid capital by the great wars and catastrophes since 1897, along with the flood of gold and consequent rise in the average index of commodity prices, has undoubtedly increased the rate of interest at least one-half per cent. In the United States sound savings banks now allow 4 per cent. on deposits, while safe bonds are quoted at prices which yield even 5 per cent.. 2. Rate of interest Earned by Investment.-Gold-mines with uncertain and scanty ore reserves, the objects of Mr. Denny's quoted remarks, are quite different from iron,. copper, or coal mines with definite mineral reserves blocked out ahead by drilling or driving. While 10 per cent is often all inadequate yield from gold-mines, the latter class of mines are often, as safe as city real estate and resemble it as an investment in more ways than one.

Jan 10, 1913

By E. M. Wise

IT is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. CONCLUSIONS 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportional limit, very low; elongation, 37.5 per cent in 2 inches. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545° and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or no grain growth resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times.

Jan 1, 1940

By Robert Poole

On June 20, 1974, delegations representing the governments of 150 nations convened in Caracas, Venezuela. The occasion: the Third United Nations Conference on the Law of the Sea. (As this article goes to press, the conference is still in session-Ed). Of all the many issues to come before the conference, none is of greater long-term consequence than the issue of jurisdiction over the seabed-the "land" at the bottom of the world's oceans. On the agenda, with widespread support from a majority of UN members, is a proposal to declare seabed resources "the common heritage of mankind," under the sole jurisdiction of the United Nations. Any would-be miner of seabed minerals would have to apply to a UN seabed authority for a permit, and would be forced to pay the bulk of his profits to a UN fund to aid the underdeveloped countries.

Jan 9, 1974

By G. S. Hume

ACTIVE drilling operations for oil were carried on during the summer of 1923 in various parts of, western Canada, particularly in Alberta. During the early part of the summer, interest centered in southern Alberta, in the Coutts area, just north of the producing Kevin-Sunburst field of Montana; but on Nov. 14 a strike of oil by British Petroleums Ltd. at its well near Wainwright, 120 mi. east of Edmonton, diverted public attention to a new field. According to present estimates, this well has a possible production of from 60 to 100 bbl. a day; the oil is 15° Be. with an asphaltic base and is obtained from a sand at the depth of 2019-2036 ft. The oil stands at 1700 ft. in the casing and there is sufficient gas pressure to cause it to flow when the well is opened. The oil horizon is in a sandstone in rocks of Colorado age. It is known that there is a terrace structure of which the western edge extends in a northwesterly direction from the vicinity of Hardisty to Viking, where it probably swings more to the north. At Viking a small dome-like structure on this terrace gives rise to an important gas field. Wainwright lies directly northeast of Hardisty. The exact structure in the Wainwright field is unknown. At Fabyan, 6 mi. northwest of Wainwright, the Imperial Oil Co.1 last year brought 1n a large gas well estimated at 14,000,000 cu. ft.; the escaping gas sprayed a small amount of heavy black oil over the derrick. The gas was obtained at a depth of 2727 ft., deeper drilling encountering a water sand. The results of drilling in the Wainwright field are encouraging for future development.

Jan 3, 1924

By W. R. Hibbard

T has been proposed1 on the basis of slip and flow I- that the ideal deformation texture of cold rolled face-centered cubic metals is (110) [112]. As pointed out recently by Brick,' this theory does not account for the difference between the pole figures for cold rolled copper and 70-30 alpha brass, which develop strikingly different spreads from the ideal orientations. It does suggest that the pole figures might be similar for these two metals if they are rolled sufficiently. This has been found to be the case for cold drawn wire.' Experimental Procedure: Four inch sections of cast cakes of copper and 70-30 alpha brass were obtained through the courtesy of the Bridgeport Brass Co. Pieces from these cakes were cold straight rolled 99.993 pct reduction in thickness with the assistance of the Remington Arms Co., Bridgeport, Conn., and by the use of pack rolling. Pole figures were made using the X ray camera and techniques described by Brick.' These pole figures were not significantly different from those previously published for the same materials rolled 98 pct. Eight thicknesses of this strip were then pack rolled. This material failed completely and extensively in tension as shown in fig. 1, developing wavy transverse fractures and bulges. No further work could be done on these samples. Summary: Within the range of this experiment, no attainable amount of cold rolling would cause the pole figures of cold rolled copper and 70-30 brass to become similar, in spite of the fact that such a similarity is predicted by theory.' References W. R. Hibbard. Jr. and M. K. Yen: Trans. AIME (1948) 175, 126. Met. Tech. Feb. 1948. TP 2334. ²R. M. Brick: Trans. ASM (1949) 41A, 99. 3W. R. Hibbard, Jr.: Trans. AIME (1949) 185, 598, Jnl. of Metals, Sept. 1949. "R. M. Brick: Trans. AIME (1940) 137, 193. 'R. M. Brick, D. L. Martin and R. P. Angier: Trans. ASM (1943) 31, 675.

Jan 1, 1951

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.' , Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1953

By V. N. Antaki

ELEMENTAL phosphorus (referred to as P,) is a true mineral product that has developed, in the relatively brief span of a century, from a laboratory curiosity to a heavy chemical. Annual production now exceeds 300,000 short tons. Continued rise in production has been predicted, consistent with new applications for P, derivatives and the expected population increase. In itself elemental P, is valuable chiefly as an 'intermediate chemical. The principal end uses at present are in inorganic phosphates, both simple and complex, of sodium and potassium, used in water treatment and detergent compounds, leavening agents, food supplements, and dentifrices. Organic P, compounds are important as plasticizers, oil additives, flotation agents, and more recently as gasoline additives (TCP being the outstanding example). The increasing use of high-analysis water-soluble and liquid solution fertilizers, as well as the direct application of phosphoric acid to the soil, will probably be the most significant factors in P, production growth rate. Coke oven plants now using sulfuric acid to fix byproduct ammonia values will gradually switch to phosphoric acid in order to market a fertilizer with completely available values. Recently sponsored experiments show that phosphoric acid can be directly admixed with cattle and poultry feed to produce rapid growth. Both P, compounds and modifiers for oil well drilling mud show increasingly promising significance.

Jan 3, 1957

By T. Sterry Hunt

THE essential principle of this new process, now in operation in Chili and in North Carolina, for the extraction of copper from its ores, is the dissolving of the oxides of copper by a hot solution of protochloride of iron and common salt. In the action which takes place, the protochloride of iron is converted into peroxide, while the oxides of copper are changed into protochloride and dichloride, the latter of which, though insoluble in water, is readily soluble in a hot strong brine. From the solution thus obtained, metallic iron throws down the copper in a metallic state, regenerating the protochloride of iron; which is then ready for the treatment of a fresh portion of oxidized copper ore. In the case of slimy ores, the contact of the bath with the ore is effected by agitation in tubs; but when the ores are granular, lixiviation in large vats is equally efficient and simpler. The hot solutions, charged with chlorides of copper, are digested in tanks with scrap-iron, or better, are made to flow through covered channels containing the scrap-iron, and in their passage lose the whole of their copper; the reaction at the same time evolving so much heat as to keep up the temperature of the liquid. In order to prevent a certain loss of chlorine, which otherwise takes place from the production of some basic ferric chloride in the reaction between the ferrous chloride and the oxides of copper (both protoxide and dinoxide being generally present in calcined ores), a portion of sulphurous fumes from the roasting is made to pass through the regenerated bath before adding it to fresh ore. This has hitherto been effected by injection, with the aid of a jet of steam.

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By C. E. Wethered

THE Morning mine is operated through one main working adit, known as No. 6 or 800 tunnel level. At a distance of 10,000 ft. underground from the portal is the vertical four-compartment, main working shaft, which extends to the 3050 level, a distance of 2250 ft. below the collar, or 800 level. Shaft-stations are cut and levels opened every 200 ft. of depth and the ore is stoped to the next level above. The vein is nearly vertical and the ore is usually fairly massive and brittle. Both walls are soft and slabby and much difficulty is therefore experienced in holding them. Stopes are usually carried up in short sections, approximately 200 ft. in length, that are mined as rapidly as possible in order to avoid a too great replacement or repair of stope timbers. The four-compartment vertical shaft, 110 ft. in the footwall of the vein, is the sole medium of outlet for all ore mined below the adit level. Two compartments of this shaft are used exclusively for hoisting ore, except at the time of changing shifts, when one compartment is used to handle some of the men and timber. The third compartment is equipped for handling men, tim-ber and all general supplies and is operated by a Nord-berg 300-hp. electric hoist. This hoist has a lifting ca-pacity of 14,000 lb. with an average rope speed of 800 ft. per minute. The fourth compartment is used solely as a manway and pipeway.

Jan 7, 1927

Shoveling ore cost so much at Tyrone during the year 1917 that it was deemed advisable to conduct tests to see where the fault lay. These tests were in the nature of time studies and extended over a period of very nearly a year. No data were available on this work to supply a starting point, so it was necessary to begin in a very elementary way, to find out the capacity of the average Mexican laborer. To' obtain a basis for comparison, it was necessary to determine the capacity of various types and sizes of shovels, so as to know whether the 21-1b. (9.5-kg.) load was the best load underground as well as on surface. A list of essential factors influencing shoveling was also made out during the course of a short series of preliminary time studies, and the motions involved in shoveling were analyzed and subdivided for convenience in studying. The necessary forms and record sheets were also decided upon at this time. A second short series of tests was then conducted on the surface, so as to be able to estimate the negative effects of underground work on the shovelers, and to minimize, as far as possible, the need for studying obviously poor types and sizes of shovels under the difficult conditions to be encountered in the mine. The test work underground consumed by far the greater proportion of the time and was divided into three series: Shoveling directly into a chute; shoveling into a wheelbarrow and tramming to a chute; and shoveling into a car and tramming to a chute. In each series the following points were determined for various lengths of time worked: Number of shovelfuls handled per minute, effect of distance thrown on shoveling speed, amount of rest required, amount of time consumed in tramming and dumping, proportion of working day occupied in shoveling, total tonnage handled during various working periods, effect of distance on tonnage handled during the day.

Jan 2, 1919

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The, time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued,-,and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1914