Search Documents

By J. Blodget Britton

Six different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285° F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530° F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212° F., and .58 more than at 285° F. Tests were afterwards made by placing other fresh portions of the

Jan 1, 1877

By E. R. Funk, H. Udin, J. Wulff

The surface tension of solid silver is measured by a refinement of the Udin, Shaler, and Wulff technique. The tests were made in a purified helium atmosphere at four different temperatures and various times. The average of the results is y = 1140 + 90 dynes per cm for the range 875° to 932°C. A SUCCESSFUL measurement of the surface tension of solid copper was reported by Udin, Shaler, and Wulff.' They performed experiments on copper held in vacuum within 100°C of the melting point. At these temperatures, the creep rate in 5 and 3 mil copper wires was sufficient to permit determination of a balance between the contractile force of surface tension and the extending force of small copper weights joined to the end of the wire specimens. By suspending a series of variously weighted specimens and measuring the change in a gage length during the test, the balancing applied load could be found. This point of zero strain is a measure of the surface tension. The mathematical formulation of this gives: w = r y [1] where w is the weight for zero strain; r, the radius of the wire; and y, the surface tension. A subsequent note by Udin pointed out that eq 1 applies only to single-crystal specimens. Since the specimens used revealed a "bamboo" structure upon

Jan 1, 1952

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By H. J. Levinstein, W. H. Robinson

A method of chemically polishing silver for metal-lographic examination has been developed. The samples are prepared by polishing on 0, 2/0, and 3/0 paper. They are then polished on 600 micro-cut paper, followed by a final mechanical polish on a cloth containing 5µ diamond paste. The samples are then chemically polished in a solution of 100 cc of saturated chromic acid and 5 cc of a 5 pct HC1 solution. The chemical polishing is performed by swabbing with a cotton ball saturated with the solution. During the chemical polishing, the sample is rinsed frequently in running water. Polishing in this manner for 5 min is sufficient to remove the strained material from the previous polishing operations. The amount of material removed is approximately 4µ/min. The surface obtained is flat and free of pits. Fig. 1 is an interference micrograph of a silver surface polished by this technique. If the solution employed is of improper HC1 content, an interference color film will form on the sample. This film can be removed either by swabbing with a cotton ball saturated with ortho-

Jan 1, 1962

By F. J. Budin

Steel supports are increasingly used in metal mines for junctions, chambers, and other wide openings and for semi-permanent areas such as haulageways, shaft stations, and pump rooms. Steel lasts longer-especially in wet mines and where foul air is present-and is procurable in different sizes that will carry heavier loads than any timber of equivalent cross section. The chief advantage of steel supports is that less excavation is needed than with timber support of the same strength, so that faster progress can be made. Since there is no possible way to calculate the exact weight on supports, sizes must be chosen by experience. Any adjustment and cutting of steel supports underground would be costly and time-consuming, and it is therefore advisable to cut sets beforehand at the surface workshops. This requires standardization of sets. All these problems have been recognized at Bawdwin Mines, Burma, where mining is difficult, slow, and very expensive. The lead-silver ore is very brittle, with hanging and footwall rock of unconsolidated rhyolite tuff. During the rainy season from May to October water penetrates into the mine, and where soft rock is present disintegration into a loose mass around openings can be expected. For this reason heavy 10x10-in. timber caps break quickly in drifts and crosscuts, and timber rots in a very short time. An average increase of 50 pct in both maintenance work and costs could not be avoided.

Jan 3, 1960

By L. K. Jetter, C. J. McHargue

DEVELOPMENT of preferred orientation in uranium is of interest because of the strongly anisotropic properties of the orthorhombic crystal structure. Harris&apos; reported inverse pole figures for rolled uranium rods which showed <010> and <410>* to be parallel to the rolling direction after On 0.19-in. spherical X-ray diffraction specimens taken from the center of the middle section of each rod, pole distribution data were obtained by the spectrometric method described previously.4 The specimen was rotated rapidly about the axis coinciding with the rod axis in order that a large number of grains could be scanned and was rotated slowly about an axis perpendicular to the rod axis. The variation in the diffracted X-ray intensity was recorded as a function of the latter motion (angle 4). Fiber-axis distribution charts (inverse pole figures) were prepared by the method described by Setter, McHargue, and Williams." After having been corrected for background radiation, the pole distribution data (I vs ?) were normalized. A normalizing factor for each plane has been shown to be Iranaom = f I sin 4 ? 4 and was obtained by graphical integration from the data for that plane plotted as I sin ? vs ?. The axis-distribution charts deduced from the normalized pole densities are shown in Figs. 1 to 3. On these charts, the contours indicate angular positions of equal normalized axis density,

Jan 1, 1958

By R. L. Templin

THE modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 lb. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately correct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements.

Jan 1, 1930

By A. A. Venghiattis

This paper is discussed not because of its intrinsic value but because it has been related by its authors to the oilwell gun perforators. It is well known that conditions almost ever present in oilwell perforations are the overburden and the presence of the casing. Because of the lack of information in the paper on the dimensions or confinement of the target rocks, one is led to guess that they were not confined at all and, particularly, that no steel front plates were used on the impact face of the rocks to materialize the presence of the cemented casing. This situation, plus the fact that small steel balls have been used as projectiles instead of actual bullets, makes the whole thing unapplicable to oilwell perforation. When shooting is performed against target rocks confined (as shown on Fig. 1) in such a way as to give a fair image of the overburden applied to the formation to be perforated, as well as of the cemented casing, the following are found. 1. There is no cratering worthy of mention, even with bullets having 10 times higher impact energy per unit projected area than the steel balls mentioned in the article. This has been confirmed with sandstone as well as with other rocks (granite, limestone and chalk). See Figs. 2 and 3. 2. Penetrations vary closely as the logarithm of the impact velocity. On this matter I have established the relation

By E. V. Given

In speaking of the concentration of oxidized lead ores at St. Anthony, I do not wish to infer that we believe all lead ores of a similar grade can be mined and treated at a profit. Our oxidized ore is low grade, and certainly the mine under present economic conditions could not operate on this ore by itself. Because of favorable conditions we can operate the oxide circuit at a small profit although we do not allocate overhead, pumping, and certain other general charges to it. Operations in the oxidized zone were started as an essential part of the development necessary to outline and mine the sulphide ores. Nearly all of our oxidized lead ore comes from the Collins section of the mine, with the transition from oxide to sulphide ore lying between the 600 and 700-ft levels. Production from sulphide ore is much larger than from the oxide, both in tonnage handled and in grade of ore. The oxide and sulphide ores are never mixed either in the mine or the mill. The oxide mill sections have their own ore bins, grinding, and flotation departments. The lead minerals contained in the ore, in the order of their importance are cerussite, wulfenite, galena, anglesite, and vanadinite. The ratios of the different lead minerals change as the ore is pulled from different parts of the mine-total lead being approximately 50% to 60% cerussite, 20% wulfenite, 15% galena, zero to 10% anglesite, and 2% vanadinite. About 3% of the lead was unidentified.

Jan 5, 1950

By Walter Harvey Weed

(Mexican Meeting, November, 1901.) Among the many causes of that perplexing featurc of mineexploitation, the unequal distribution of the ore, the influence of the country-rock upon the vein-contents has long beer1 accepted as an important factor in certain districts, but the general application of the theory has not been proved. It is now possible to obtain trustworthy data with which to test the theory, and either to confirm or to overthrow this time-honored

Jan 1, 1902

By Andrew S. McCreath

THE manufacture of pig iron for conversion into steel by the Bessemer and open-hearth processes, is now one of the most important industries of the United States. It is necessary that iron intended for this purpose should be very pure, and especially must it be comparatively free from phosphorus. Great care must therefore he exercised in the selection of proper ores, flux, and fuel. Only such ores as are practically free from phosphorus can be used, and pure fuel is as much a necessity as pure ores; though hitherto iron men have paid comparatively little attention to this point. During the course of my work as chemist for the Second Geological Survey of Pennsylvania, I had occasion to examine some of the bituminous coals of the State for phosphorus, and the results obtained are so interesting that I venture to present them to the notice of the members of the Institute. The coals are arranged in geological order according to the different beds, and the table shows the percentage of phosphorus in the coal and also in the coke. The greatest number of specimens have been selected from the Pittsburgh bed, because it is the principal coal-bed of Southwestern Pennsylvania, and most of the mineral fuel which is mined along the Youghiogheny and Monongahela rivers, to be used in the coke ovens of the Connellsville region and in the blast furnaces and mills of Pittsburgh and its vicinity, and to be shipped to Western and Southern markets, comes from this bed. It will be noticed that many of the specimens examined contain

Jan 1, 1880

By Frederick Prime

IN this supplementary list no titles to which an * is prefixed have been seen by the compiler; and he will be most thankful to have any omissions or inaccuracies in the list sent to him to be published as a second supplement in the next volume of the Transactions. The author is indebted to Messrs. Robert Clarke, of Cincinnati ; Thomas Macfarland, of Towanda; Professor F. W. Simouds, of Chapel Hill; and Professor J. J. Stevenson, of New York, for valuable assistance. CEDAR POINT IRON COMPANY, BALTIMORE, July 31st, 1880. ALABAMA. Geological Survey of Alabama. Report of Progress for 1877 and 1878 ; by Eugene A. Smith, State Geologist. Montgomery, 1879. 8vo., 139 pp., and 4 maps.

Jan 1, 1880

By T. E. Schwarz

The Red Mountain district, in Ouray County, Colorado, has been already referred to in the Transactions of the Institute, and notably in papers by Mr. T. B. Comstock, on " The Geology and VeinStructure of Southwestern Colorado" (Trans., xv., 218), and on " Hot-Spring Formations in Red Mountain District, Colorado—A Reply to the Criticisms of Mr. Emmons" (Trans., xvii., 261), and in the paper of Mr. S. F. Emmons, on " Structural Relations of Ore-Deposits" (Tram., xvi., 804). The district has attracted much attention from those interested in geology, because it seems to present a variety of ore-deposits rarely, if ever, met with elsewhere, and one which cannot be described by such well-understood terms as fissure-veins, bedded-deposits, or contact-formation. It will be the scope of this paper to note briefly, from the writer&apos;s experience in developing the Yankee Girl, Guston and other Red Mountain properties,—first, observed facts as to the ore occurrence and formation, and second, certain unsolved geological questions. The Red Mountain district proper occupies the headwaters of Red creek, from Iron ton to the Divide, a distance of 5 miles. Its leading properties occur on the west slope of Red Mountain. The mode

Jan 1, 1890

By R. W. Raymond

I DESIRE to call the attention of the Institute briefly, and by no means in the way of an exhaustive description, to the interesting developments recently made on the east bank of the Hudson River, in the mining of spathic iron ores. The mines to which I refer are those of the Hudson River Spathic Iron Ore Company, situated at Oakhill on Hudson, Columbia County, N. Y., five or six miles from the city of Hudson, and opposite the town of Catskill. The ore occurs in beds, constituting apparently members of the stratified series of rocks on that side of the river, coursing nearly north and south, parallel with the river, and dipping east. The principal outcrops are presented in a range of low hills, about one mile from the river, along the crest, on the western face of which the stratum of spathic ore is more or less exposed. The length of the line in this range, along which, at various openings the ore has been discovered in profitable quantity, is about two miles. To the northward, the hills are somewhat higher, and the stratification may possibly be disturbed, though the rapid examination of the locality which I made in November last did not, include any determination of this

By C. H. G. Bushell, M. Malnarich

Reagent control in flotation is more an art than a science. Operators vary the amount of re- agents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercorrection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment.

Jul 1, 1956

• Phelps-Dodge Corp. signed an agreement with the Defense Materials Procurement Agency to increase copper production from the east ore deposit of the company&apos;s Copper Queen branch at Bisbee, Ariz. The company agreed to undertake a $25 million expansion program, including construction of a concentrating and leaching plant at the Bisbee mine and enlargement of the Douglas smelter. The Government agreed to buy the first 112,500 tons of the first 150,000 tons produced at 22e per lb if the company could not sell at a higher price. The new facilities will have a yearly capacity of 38,000 tons and should be in production by late 1954 or early 1955. • American Smelting & Refining Co. has started construction of a new building to house the Central Research laboratory at South Plainfield, N. J. It will have approximately 75 individual laboratories and an equal number of offices and shops. Modern apparatus to be installed will include electron microscopes, electric and fuelfired furnaces, miniature copper refineries and zinc plants, wire drawing machinery, and large pilot plant laboratory. In the new building scientists study the base metals, and the development of new uses for a number of Asarco by-products, arsenic, and little

Jan 11, 1951

By K. C. Lau

INTRODUCTION The design of engineering structures such as mine openings in and foundations on rock requires a knowledge of the constitutive laws governing the behaviour of discontinuous and layered rock masses. At the present time there are two main approaches for predicting the stress distributions and displacements in such engineering structures. In one method, the whole of the rock mass is discretized. The behaviour of the components of the rock mass, that is, the joints and the intact rock are modelled using analytical techniques such as the finite or boundary element methods. Typically the intact rock is modelled as a linear elastic material bounded by non-linear discontinuities. An alternative method of analysis is to describe the load-deformation properties of the jointed, layered or even reinforced rock mass in terms of smeared or equivalent homogeneous material properties. Such equivalent material properties may then be used to compute the stress distributions around openings and in foundations using standard methods of analysis such as the finite or boundary element techniques. Once the stresses have been obtained for the equivalent material, the stresses in the individual constituent layers or discontinuities may then be determined. Each approach to the problem has particular advantages. The first method is more likely to yield results which more closely represent the behaviour of the rock mass, since the behavioural responses of both the joints and intact rock are modelled. However, for many large or complicated geologic structures such an approach can become unweildy and uneconomical. In such cases, the equivalent

Jan 1, 1984

By Frank T. Wheby

The cost of tunneling is highly sensitive to the rock characteristics through which the tunnel is to be driven. These characteristics affect in a major way the rates at which tunnels and shafts can be driven and the degree to which the openings must be supported to maintain them in a permanent stable condition. Tunnel and shaft design and cost criteria have been computerized, permitting estimates of tunnel-shaft systems to be made directly from inputs of rock mechanics characteristics and other data. Curves of quantities of steel, rock bolts, and other rock support items as related to tunnel size and rock quality designation are presented. An illustrative example of the use of the program in calculating the cost of a hypothetical tunnel system is included.

Jan 1, 1971

By E. L. Kapfer

A preliminary description is made of the field of automation and optimization of the oxygen blast furnace process. The concept of static and dynamic process control is illustrated. After a short general description of all factors concerning the optimization of this process, a learning system is derived which gives better results than models previously used. This learning or self-adaptive control system uses statistical methods with exponential aging of process data and requires derivation of multi-variable functions of the process for which measurements can be made available. The practical application of this new procedure and of additional measuring instruments are discussed, and results obtained in plants using the adaptive control system are described. A survey of European steel plant automation using the Siemens technique is presented.

Jan 1, 1969

By E. J. Bruderlin

A METALLURGICAL process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the dis-tillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working block must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort -to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retort-ing plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the- introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator&apos;s difficulties.

Jan 1, 1936