Search Documents

By Carel Robinson

MECHANIZATION of coal mine, is radically changing the requirements for under-ground transportation. It has increased materially the need for reliability and belt conveyors are the most dependable means of moving coal away from the place where it is mined. Their record of freedom from delays is almost 100 per cent. Why then are- not belt conveyors in more general use. Part of the answer lies in the pour records made at some of the earlier installations, and in the fact that belts have so long been identified as a type of equipment suitable, in the main, only to thin seams. Another reason is lack of knowledge of the full potentialities of belt transportation.

Jan 1, 1941

Jan 1, 1903

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice this ideal situation is not possible. Several basic methods of equipment scheduling, with an infinite number of minor variations, are used. The first approach is the use of a "minimum equipment fleet," of which all items or equipment are scheduled each working shift.

Jan 10, 1967

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foothills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today. The Heath gypsum mine was developed by the Northwest Gypsum Co. in 1916. The products of the small mill built by this company were plaster, agricultural gypsum, and raw gypsum for cement manufacturing. The United States Gypsum Co. prospected the adjacent property in 1916 and 1917 by means of two adits and some exploration drill holes. During World War I, the company abandoned operations at Heath, but again became active in this area in 1928 hen it purchased all the property of the Northwest Gypsum Co. A long range program of expansion was begun with the building of a block plant and the purchase of additional land and mineral rights. A modern wall board plant was built in 1936. When the old wooden mill purchased from the Northwest Gypsum Co. burned in 1937, an all-metal calcining plant located at Blue Rapids, Kansas, was dismantled, moved to Heath, and erected on the site of the mill. In August 1951 a new mine was opened 3000 ft north of the mill. Rock is conveyed from the mine to the mill by an 18-in. belt conveyor. The Heath gypsum deposit lies at the base of the Ellis formation of Jurassic Age. The Ellis at Heath lies unconformably on the black fissle shale of the Heath formation of the Big Snowy Group, which is Mississippian in age. The strike of the gypsum bed is N45°E and the dip approximately 3" NW; the regional strike and dip of the area. The gypsum lies in a series of six layers separated from each other by thin seams of shale. The lower layer is composed of' gypsum and shale intermingled and is not of commercial grade. The upper five layers are high in purity, but only the middle four layers are mined on the advance, as the top layer is left for roof support. This top layer is mined on retreating operations at the same time the pillars are robbed. Total thickness of the gypsum layers varies from 12 to 14 ft. Fig. 2 shows the average thickness and arrangement of the layers. Mining Methods The mine was originally developed by driving an adit into the gypsum horizon. The Northwest Gypsum Co. mined in the top four layers, the top layer being split, leaving about 12 in. for roof support. A modified room and pillar method was used: entries were 15 ft wide and rooms varied between 20 and 30 ft and were turned on 90" from the entries. Crosscuts between the rooms left pillars from 10 to 20 ft square. The rock was loaded by hand into 1-ton mine cars and pulled to a central gathering point by mules; from the gathering point, mules or horses were used to pull the string of cars to the mill tipple. This method was continued by the United States Gypsum Co. from 1928 to 1937.

Jan 1, 1954

By AIME AIME

THE Coal Division holds its fall meeting in the Pocahontas coal field, at the West Virginian Hotel, Bluefield, W. Va., Oct. 9 and 10. The first day will be a busy one-two sessions for the presentation of papers and a dinner in the evening. Hon. E. Fudge, Assistant Undersecretary, Mines Department, and R. V. Wheeler, head of the Mines Research Board of Great Britain, will be the guests of the Division. Mr. Wheeler will discuss the British Mining Act as relates to the coal industry. George S. Rice, Chief Mining Engineer, U. S. Bureau of Mines, will present an account of the recent meeting at Buxton in England, of representatives of England, Germany, France, Belgium and the United States to formulate a plan and to correlate research work now in progress in the various countries. The second day the members will be the guests of the operators on a trip through the Pocahontas field. The work of preparation for the meeting is being actively pushed by committees headed by T. H. Clagett, R. M. Lambie and H. D. Smith, and a good attendance, both local and from the general membership of the Division, is anticipated. Because many will make the trip by car the principal automobile as well as rail-road connections to Bluefield are given here. The program for Friday, Oct. 9, follows:

Jan 1, 1931

By AIME AIME

THE statements quoted below range widely over the field of contact between education and industry. 'Their sources are as indicated. True Education "Education must escape from its traditional warped and narrow views as to what constitutes life and preparation for life. It must train young men and women for vigorous, wholesome development of every important element of personality. It must build physical and mental health. For each student it must inform and discipline thinking in literature, in physical, bio- logical and social sciences, and in philosophy. It must awaken appreciation of beauty.

Jan 1, 1929

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By David J. Mack, Dennis R. O’Boyle

The mechanical properties of three polycrystalline intermediale Phases that have the y bvass structure were measured in compression between 400° and 900°K. At the lower testing temperatures— termed Region I— no plaslic deformalion occurred prior to brittle fracture. A1 higher temperatuves— lermed Region III—the three phases deformted plaslically for all strain rules from 1.5 to 36.0 x 10-4 sec-1. The homologous temperature for the inilialion of plaslic flow increased in the same order as tile atomic size difference between atoms in each plmse (0.50Tmp for y AgZn, 0.62Tmp for y CuZn, and 0.76 Tmp for y CuCd). The increased flow resistance oj. y CuCd above 0.50Tmp is explaitzed in terms of the more random arrangement of copper and cadmiwn atoms on the laltice sites of&apos; the y bvass slrilctlire. Plaslic deformation of the three intevmiediate phases in the smooth plaslic flow region appears to be controlled by oacancy-induced dislocation climb. RESULTS are reported in this paper on the mechanical properties of three binary intermediate phases having the complex cubic y brass structure (D82, 143m) containing fifty-two atoms in the unit cell. The structure of the prototype y brass phase, y CuZn, was first analyzed by Bradley and Thewlis&apos; based on the X-ray work of Westgren and Phragmen.2 The y brass structure can be visualized as an arrangement of twenty-seven body centered cubes (3 by 3 by 3) into a unit cell containing fifty-four atoms. From this cell the center atom and the four corner atoms are removed and the remaining fifty-two atoms are slightly displaced, resulting in the y brass structure. Approximately thirty-five binary intermediate phases that have an electron to atom ratio of 21:13 have been reported to form the y brass structure. The three y brass intermediate phases selected for this study are formed from elements in groups IB and IIB of the first and second long period. Each compound exists over a composition range that includes the stoi-chiometric composition A5BB (Cu5Zn8, Ag5Zn8, Cu5Cd8). y CuZn (a0 = 9.944A) has solubility limits extending from 57 to 67 at. pct Zn at 500°C apd melts peritecti-cally at 834°C; y AgZn (a0 = 9.326A) has a solubility range from 58 to 63 at. pct Za and melts peritectically at 661°C. y CuCd (a, = 9.596A) melts congruently at 563°C and has a maximum range of solubility extending from 58 to 64 at. pct Cd. In order to minimize coring and microporosity during solidification, the composi- tion of the compounds that form peritectically (y CuZn and y AgZn) was chosen so that the temperature difference between the liquidus and the solidus is only a few degrees centigrade. In selecting y brass compounds for this study, phases were avoided that contained a transition element or that had an electron to atom ratio greater than 1.70. Hume-Rothery et a1.3 has observed that, when the electron to atom ratio of y brass intermediate phases exceeds 1.70, atoms begin to drop out of the unit cell to maintain a constant electron to unit cell ratio. EXPERIMENTAL PROCEDURE Each of the three intermediate phases was prepared from elements having a purity >99.999 pct. Only trace quantities of impurities (<0.0001 pct) were detected by spectrographic analysis of the four elements. A master alloy of each compound weighing approximately 130 g was prepared by melting the elements in evacuated sealed quartz tubes heated in an electric furnace. Specimens having the desired diameter for the mechanical property measurements were obtained by remelting the master alloy in a Vycor tube under argon and drawing specimens from the melt into 4-mm-diam quartz tubes. To obtain a smooth surface on specimens drawn from the melt, the inside of the quartz tube was coated with a thin layer of graphite formed by thermally decompositing acetone. All specimens were imbedded in sealing wax and cut to the proper length with a diamond-impregnated cut-off wheel. The individual specimens (4 mm diam by 8 mm long) were then sealed in evacuated Pyrex tubes and homogenized at 500°C for 72 hr. Chemical composition, variations over the length of the rod (10 cm long) were generally less than 0.2 pct and the analyzed composition differed from the desired composition by less than 0.5 pct.4 Metallographic evaluation of the specimens after homogenization showed no evidence of a second phase in any of the compounds. The average grain size of the specimens after homogenization was 1 to 2 mm. All mechanical property measurements were carried out in an argon atmosphere using a compression apparatus described previously.5 Prior to applying the load to the specimen, the test apparatus was evacuated, back-filled with argon, and heated to the test temperature for 20 min to establish thermal equilibrium. EXPERIMENTAL RESULTS Mechanical properties measured as a function of temperature and strain rate for each of the three y brass phases were similar. From room temperature to the ductile-to-brittle transition temperature, only elastic deformation was observed prior to fracture.

Jan 1, 1968

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Ti-Mn alloys were studied in order to determine the factors affecting the mechanical properties of &stabilized titanium alloys. The principal compositional factors have been found to be solid-solution strengthening, the martensitic transformation, and instability of the P phase. Structural factors, such as grain size and shape, were found to have more influence on ductility and toughness than on strength. THE alloys of titanium with the &stabilizing elements offer the chief hope for developing useful heat treatments. Conversely, the heat-treatment response possible with the p-stabilizing elements causes difficulties such as weld embrittlement and thermal instability during service at elevated temperature. Therefore, it is of considerable technical importance to understand the factors that govern the heat-treatment responses in these alloys, so as to be able to soften the alloys if they are embrittled by an adventitious heat treatment, to render them stable in service, or to harden them while maintaining adequate ductility and toughness. The Ti-Mn system is a good example with which to demonstrate the factors that govern strength and heat-treatment response in. a P-stabilized system. The region of the a-j3 transformation, after the work of Maykuth, Ogden, and Jaffee,&apos; is shown in Fig. 1. The a solubilities are low. This means that, in the two-phase a-p field, partition of manganese between the two phases occurs practically only to the P phase. The solid-solution effects are therefore chiefly the result of solution in the ,8 phase. The eutectoid occurs at 20 pct Mn and 550°C, and proceeds very sluggishly. It can be ignored in heat treatments in hypo-eutectoid alloys, except for long-time storage at low temperatures below the eutectoid temperature. Even here, there is some question that diffusion proceeds far enough to involve eutectoid decomposition. Three compositional factors bear on the mechanical properties and structure of titanium a-P alloys. These are: 1—solid-solution strengthening, 2—mar-tensite transformation, and 3—P instability. Combined with the purely structural factors of grain size and shape, these govern the properties of the alloys. Perhaps the most important factor is solid-solution strengthening. The facts that manganese dissolves in a titanium to a maximum of only 0.5 pct and most of the manganese partitions to the p phase dominate the structure and properties of the a-/3 alloys. Because of the overwhelming preference of manganese for the ,3 phase, the P phase is harder and the a phase is softer. The relative amounts of both phases may be modified by heat treatment in the a-P field as application of the lever rule in the two-phase field clearly shows. A critical temperature in the Ti-Mn diagram is 800°C. This is the P transus temperature of the 6.4 pct Mn alloy, which has the lowest manganese content which will form all retained-P phase on quenching to room temperature. Any quench performed from below 800°C will produce a structure consisting of only a, a plus retained P, or retained p, for alloys of the compositions used in this work. For alloys containing less than 6.4 pct Mn, any quench from above 800°C will always result in structures

Jan 1, 1955

By W. F. Hower, W. Brown

Large-scale sand consolidation tests were conducted in an effort to determine the reasons for the successes and failures of this method of sand control. Several different consolidating materials were used in treating both clean and bentonitic sands that were packed in a chamber having a capacity of 3.3 cu ft. The results were essentially the same for all of the different consolidating materials, The data show that low-viscosity consolidating materials pumped at a relatively slow rate gave the best results. Where the formation has produced sand, the treating fluids can compress the formation, thus permitting the channeling of fluids to another horizon. Pressure-packing these zones before attempting to consolidate is recommended. Sands containing more than 4 per cent of water-swelling clays are not good candidates for consolidation. It is indicated that loose sand, particularly when it is bentonitic, can be fractured during the placement of the treating fluids. INTRODUCTION Sand production in oil and gas wells has plagued the industry for many years, and numerous cures for this problem have been suggested. Most methods have been successful to a certain degree, but the great variety of well conditions that exist in the different areas has magni- fied the problem and limited the successful use of the various systems. Four review papers1-4 present a wealth of information concerning the degrees of success that have been obtained by the different sand-control methods. The bridging of sand grains by the use of gravel packs and screens has been quite successful. However, these methods do not leave the casing clear for all types of multiple completions, and the cure does not last for the production life of the well in some instance:;. The control of loose sands by sand consolidation with resins has never been as successful as desired. It has always been hoped that such a treatment would eliminate all sand problems for the life of the well, but. initial applications, starting in the middle 1940&apos;s, were only moderately successful. Lott, et a1,3 reported a success ratio of approximately 50 per cent and made the following conclusions. The highest percentage of successes were obtained where: a. Consolidation of a zone was made at the time of initial completion or prior to the production of sand. b. The interval treated was less than 12 ft in length. c. Between 30 and 50 gill plastic/ft of producing interval was displaced through the perforations. REASONS FOR SAND CONSOLIDATION FAILURES Our own experiences in the field of sand consolidation point toward the following conditions as the major reasons for the failure of sand consolidation attempts. 1. Mud-plugged perforations and mud invasion of the formation. 2. Sand in the casing covering all or part of the perforations. This sand could be either formation sand or one of the coarser sands used as propping agents in hydraulic fracturing. 3. Holes in the casing. 4. Channels behind the casing. 5. Attempting to treat too long a perforated section. 6. Too high a percentage of water-swelling clays in the formation. 7. Formations that have produced sand. Recent attempts were made to treat perforated sections ranging from 10 to 30 ft, in wells that have produced sand, by using a straddle packer that was raised and lowered through the perforations as the consolidating material was being pumped. In most instances, the pressure required to pump fluid into the formation varied considerably as the tool was raised and lowered. This suggested the possibility that significant differences in permeability were present or that only part of the formation had produced sand. There were times when a sudden break in pressure indicated that a fracture was being formed. Research conducted several years ago concerning the problem of the control of water in air and gas drilling indicated that shale sections could be fractured quite easily. In addition, it was determined that it was easier to pump fluids into shale bodies by fracturing the shale itself, or the interface between the shale and sand, than to pump into a fluid-saturated formation. Formations that produce sand are usually adjacent to shale bodies and frequently have shale streaks of various thicknesses inter-bedded in the sand. Therefore, where shale is exposed to fluid pressure it

By Jei Y. Choi, P. G. Shewmon

Using a scratch smoothing technique, the magnitude and the ratio of the surface diffusion coefficients (D,) in two orthogonal directions have been measured on copper for over 100 different surface orientations. Anisotropy was found for all surface orientations except those lying near the (100) and (111); however, these anisotropies were rarely greater than 2.0. The direction of maximum D, appears to coincide with the direction of step edges on any given surface, and if no such steps exist, no anisotropy is found. Thus the jump frequency along a step edge is shown to be faster than the frequency of a jump over the step. The values of Ds and AH for the (100) and the (111) orientations agree quite well with those obtained earlier by the grain boundary grooving technique. It is proven that the directions of maximum and minimum D, (the principal axes) for any surface orientation are known if the perfectly ordered plane corresponding to the given surface orientation possesses a plane of mirror symmetry. Thus the principal axes of D, for orientations lying along the sides of the unit stereo-graphic triangle are always known independent of the extent of thermal disorder or impurity adsorption. The merits and shortcomings of King and Mullins&apos; recently published equations relating Ds to the rate of scratch smoothing are discussed. 1N an earlier paper the authors have reported the variation of the surface diffusion coefficient (Ds) with surface orientation on copper.&apos; In that study Ds was determined from the rate of growth of grain boundary grooves on symmetric bicrystals. This gave values of Ds from 850° to 1070°C in a given direction on each of the six surfaces. It was found that the activation energy for surface diffusion was essentially the same for all six surfaces. The theory developed to explain these data assumed that the free energy of any given type of surface site depends only on the number of nearest neighbors the atom has. This same theory predicted that on any given surface Ds should be independent of direction. The primary aim of this study was to check the validity of this prediction for a wide range of surface orientations on copper. The growth of grain boundary grooves is ideal for studying Ds in a given direction on a given surface over a range of temperatures, because the same specimen can be repolished and used again. However, there is considerable work involved in growing a symmetric bicrystal, and for a survey of Ds in two or more directions on many surface orientations, the technique would be arduous. A better technique appeared to be the scratch method used primarily by Mykura. 2 If a scratch is placed in a surface whose surface tension is independent of orientation, the surface will smooth out in time under the influence of surface tension. To determine D, from this flattening, Blakely and Mykura2 used an approximate solution which was assumed to describe the rate of flattening. Recently King and Mullins3 (hereinafter K and M) have given a more exact analysis of the flattening of an isolated scratch. A second aim of this paper was to check the validity of this newer analysis and compare the values of Ds determined thereby with the values obtained from grain boundary grooving techniques. EXPERIMENTAL PROCEDURE In an effort to work with a particular predetermined surface orientation, light orthogonal scratches

Jan 1, 1963

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,&apos; in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20&apos; to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200&apos; and 250°C. (392&apos; and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures&apos; The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,&apos; in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20&apos; to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200&apos; and 250°C. (392&apos; and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures&apos; The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

By H. J. Fraser

LIKE a runner catching his second wind, the mining geologist in 1944 has had some opportunity to appraise the result of three years of active and intense search for the metallic sinews of war and peace. The war period has been one of physical activity and accumulation of new data but has not so far resulted in the announcement of any profound or revolutionary theoretical concepts or techniques. Most technical publications during the year have been either descriptive or statistical. A review of accomplishments during the war years, although affording some measure of satisfaction in individual cases or regarding production of certain metals or&apos; ores, is far from justifying any feeling of complacency regarding the growth of the profession either in fundamental knowledge or in application. During 1944 an abundant supply of all metals and minerals flowed steadily to smelters and fabricating plants. Also, during this and preceding years, adequate stock piles for war needs, in view of the improved foreign and domestic supply situation, were accumulated in many metals in such quantities that the mining industry has become concerned not with the problem of supply but with the effect these accumulated stocks, if maintained, might have on the postwar market. These considerations culminated in the enactment by Congress of the Surplus Disposal Act, which, admittedly a tempo-

Jan 1, 1945

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64&apos; May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By R. A., Pallanch

SO many variations of lead-zinc ores occur in nature that it is impossible to state any rules that will apply to the concentration of ores of this type. Some have lead and zinc in approximately equal amounts; others may have pre- dominant amounts of one or the other metal. There are gradations from all sulfide to completely oxidized minerals. Some such ores carry little pyrite, others contain much more pyrite than they do lead and zinc combined. The behavior of ores in flotation is largely a function of their lead-zinc ratios. their content of pyrite or pyrhotite, the nature of existing soluble salt conditions, the character of the gangue constituents: and the speed with which the minerals float. For the purposes of this paper only those lead-zinc ores handled commonly in present-day flotation practice will be considered. These are practically all-sulfide ores with relatively minor degrees of sulphatization or oxidation.

Jan 1, 1936

By C. T. Holland

This discussion is concerned with those com-J- paratively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth&apos;s crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities." Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.&apos; CAUSES OF ROCK BURSTS Rock bursts in coal mines have occurred in sev-eral places under diverse geological conditions, mining methods, and/or practices. A study of many such occurrences indicates that they depend on the following conditions: 1) cover thickness of 500 ft or more, 2) cover composed of strong members and having a strong member lying close to or on the coal bed, and 3) a floor that does not readily heave. The minimum thickness of cover under which coal mine rock bursts occur is based on observation. Under unusual circumstances involving very strong roof members and/or mining systems, and/or practices especially likely to induce bursts, a burst conceivably could occur under less roof. Under special circumstances rock bursts have occurred in marble quarries almost at the surface.&apos; Furthermore, under very heavy cover it is likely that controlling roof members need not be as strong and as close to the coal bed to cause bumps. Just what constitutes a strong roof or roof member is open to question. Obviously the strength of a roof member is determined by its thickness, the distance between bedding planes across which little or no bond exists, the spacing and development of joints, and the inherent strength of the rock material. Strata sections showing roofs under which rock bursts in coal mines have developed are illustrated in Fig. 2. In several instances the strength of rocks composing the roof of mines developing bumps has been tested. The tests (Table I) show that these rocks develop considerable strength in compression, bending, and shear and that in some cases the strengths are very high. No quantitative data are available concerning joints in roof members over coal beds where rock bursts have occurred, but the author has examined many mines subject to bursts and has received the impression that joints in the shales immediately over the coal beds are always present and well developed. In the main sandstone or conglomerate members themselves, however, where observed, he has yet to see a fracture system indicating well developed joints. Undoubtedly joints are present, but the evidence indicates that they are few, poorly developed, and widely spaced. In a mine subject to bumps, moreover, actual measurements of roof spans up to 225 ft between supports under a cover of about 800 ft have been made before roof failure occurred. Such spans signify strong roof. In coal beds subject to rock bursts, the bottom rock is usually a sandy shale. A few tests (Table I) have been made on the floor rock of coal beds. Observations in mines indicate that they are usually weaker than roof rocks and that under load they show more plastic effects. Observation in ground subject to bursts invariably indicates a relatively strong floor highly resistant to heaving, although some heaving may occur. Other factors listed as favorable to rock bursts are: 1) mountainous surface; 2) steeply dipping beds; 3) proximity of faults, folds, and other similar geologic structures. Many bursts have occurred in mines under mountainous country, although many bursts in mines under a surface with little relief indicate that thickness of cover, not relief, is the essential factor. In steeply dipping beds, many bursts occur in mines that are essentially flat, and rock bursts have been recorded in beds dipping as much as 35o Most rock bursts in the U. S. occur in beds that dip less than 10 pct. It is also true that most U. S. coal is produced from beds dipping less than 10 pct. Geologically, faults are regarded as providing stress relief, but in the vicinity of faults, as well as sharp folds, it would seem that residual stresses could be present. The fact that rock bursts occur in areas remote from faults and sharp folds suggests that their presence is not necessary for this phenomenon to take place. There have been many bursts close to faults and folds, and it may be assumed that occasionally such structures accentuate their occurrence3 The conditions and circumstances under which they occur, coupled with the effects produced, leave In the Crowsnest Pass coalfield, British Columbia, a rock burst is estimated to have released 1.8 million cu ft of methane.

Jan 1, 1959

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes back well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948.

Jan 1, 1949