Search Documents

By H. Pew, J. H. Field

To alleviate pollution more restrictive legislation is being enacted, either limiting emission of pollutants or the type of fuel that can be utilized. The nature and magnitude of air pollution problems affecting the mining, preparation, coking and combustion of coal are described. Methods for combatting particulate emissions by use of mechanical separators and electrostatic pre-cipitors are discussed. Proposed methods to meet the problem of gaseous emissions currently receiving considerable attention are described, with special emphasis on methods to decrease pollution by sulfur oxides. Concern about air pollution goes back several centuries, but until very recently most effort has been aimed at coal smoke and other visible pollutants. The classic example of a 'successful' campaign for smoke abatement and control is the fruitful combined effort of the city of Pittsburgh and its surrounding Allegheny County, which eventually led to the reconstruction of downtown Pittsburgh at an estimated cost of one billion dollars. Historically, the city's downtown Golden Triangle district had been afflicted by pollutants evolving from steel mills, from a variety of other industries, and from railroad locomotives. Efforts to alleviate the situation prior to 1943 were virtually ineffective. In 1945, however, a comprehensive redevelopment plan was prepared and backed by state authority. Within a few years a clean, modern metropolis has evolved where once stood America's famous 'smoky city.' But the victory in Pittsburgh, as in various other American cities, has not solved the national problem. Current estimates indicate that 133 million tons annually of air pollutants from all sources still are emitted annually into the atmosphere above the United States. About 10% of this annual effluent is particulate matter so that most of the remaining pollution problems will be solved only when other effluents are reduced. Essentially, these are sulfur oxides, nitro- gen oxides, hydrocarbons, and carbon monoxide. Over the years, both states and local communities have tended to increase the restrictions on smoke and fly ash — problems mostly of concern in the combustion of coal. Prior to the middle 1950's, ordinances sometimes permitted emissions of smoke equivalent to as much as No. 3 on the Ringlemann scale. Since 1956, no ordinance has been passed which allows smoke of greater than No. 2. Under today's conditions of improved fuels, equipment and practice, a few communities have passed laws prohibiting emission of smoke of any density darker than Ringlemann No. 1. The majority of existing laws on fly ash emission in the U.S. limit emissions equivalent to 0.85 lb of fly ash per 1000 Ib of flue gas. In recent years, however, regulations which have been adopted give cognizance to the higher level of performance now obtainable with improved equipment. A comparison of the restrictions of five codes adopted since 1960 is given in Table I. The most stringent of these is the one for New York City which provides for a maximum emission of 0.6 lb fly ash per million Btu heat release (equivalent to roughly 0.51 lb/1000 lb of flue gas). The first comprehensive effort to restrict the emission of SO2 resulted from the passage of a 1937 law in St. Louis. This regulation stipulated that coal containing in excess of 23% volatile matter and 2% sulfur must be washed, thereby presumably producing some effective reduction in the input sulfur content. This was followed in 1949 by a Los Angeles County law which prohibited the emission of SO2 in concentrations greater than 0.2%. Most SO2-restrictive legislation passed since that date has been based on this limiting 0.2% SO2 by volume, although modifications are occasionally permitted under selected conditions, sometimes based on the fact that certain limiting ground concentrations are not exceeded — such as in the rules adopted by the San Francisco Bay area. To date, no legislation has been passed in the U.S. to limit the generation of nitrogen oxides from the combustion of fossil fuels. However, such oxides are considered to be of potential importance in air pollution control because of their possible detrimental effects on health and their reported role in the formation of photochemical smog. Interest in reducing oxides of nitrogen from powerplant and auto exhausts is increasing and regulations limiting their quantity can be expected in the future.

Jan 1, 1968

By Lawrence H. Van Vlack, Otto K. Riegger, Gerald I. Madden

The microstructural variations of periclase (MgO) in the presence of oxide liquids are examined under the steelmaking variables of: 1) temperature, 2) liquid composition, and 3) FeO additions under different oxidation levels. Attention is given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. Silicate liquids penetrate more extensively between individual periclase grains than do liquids containing high percentages of Fe2O3 Higher MgO solubilities in the liquid and lower MgO contents of the solid favor more rapid grain growth. The presence of a second solid phase reduces the periclase grain growth rate and increases the amount of the solid-to-solid contact within the oxide microstructures at high temperatures. The service suitability of a refractory depends on many factors. Two are of major importance and include 1) the thermal resistance to melting, and 2) the mechanical resistance to loads at service temperatures. Neither is a simple consequence of the service temperatures because service conditions will alter compositions, produce partial melting, and induee phase changes. Consequently, the equilibrium phase relationships have been rather thoroughly studied and give a knowledge of the thermal resistance to melting, but do not give full information about the mechanical properties because two refractories with the same types and quantities of phase may have different microstructures. Although variations of microstructures with time, temperature, and composition have been subjects for extensive investigation in metals, only a limited amount of comparable microstructural work has been performed for refractory materials.' This study was an attempt to evaluate some of the consequences of service parameters upon the microstructures of refractories so that bases may be established for the analyzing of high temperature mechanical properties. Periclase (MgO) was chosen as the refractory oxide; variables included those which are encountered under steelmaking conditions such as 1) temperature, 2) liquid composition, and 3) FeO additions under various oxidation levels. Specific attention was given to the distribution of the phases, both liquid and solid, and to the growth of individual crystalline grains. The most closely related work on microstructures of polyphase materials is that of Van Vlack and Rieg-ger2 on the microstructure of magnesiowüstite [(Mg,Fe)O] in the presence of silica. In that work which pertained to solid solutions with less than 40 pct MgO, most of the quantitative work was performed on FeO microstructures. The chief conclusions concerning these relatively low-melting oxide solids were as follows: 1) the rate of crystalline grain growth is inversely proportional to the grain diameter, 2) grain growth proceeds more rapidly at higher temperatures but is slightly retarded by additional liquid content, and 3) a Silicate-containing liquid penetrates as a film between the individual magnesiowüstite grains independent of time, temperature, amount of liquid, or the MgO/ FeO ratio. The above observations are in contrast to prior work3 on the microstructure of silica in the presence of iron oxide-containing liquids where the liquid does not penetrate as a complete film between solid grains. The phase relationships for the compositions of the present work are shown in Fig. 1 which is a summary of the work of several investigators.4 Of importance is the fact that CaO forms a more stable structure with SiO2 and Al2O3 than do either MgO or FeO. The oxygen potential has little effect on periclase unless iron oxide is also present. The iron oxide is ferrous at moderately low oxygen levels, changing to ferric as the Oxygen potential is increased so the spinels, magnetite, and magesioferrite are formed.5 These two phases are relatively stable in air at steelmaking temperatures. I) EXPERIMENTAL PROCEDURE ractory were made with reagent grade Oxides. The magnesium oxide used was 99 pct MgO after ignition, and the iron oxide raw material had a minimum content of 99 pet Fe2O3. The CaO, SiO2, and A12O3 were also reagent grade raw materials. After mixing, the required compositions were pressed into pellets at a minimum pressure of 5000 psi to insure compaction of the raw materials and prevent excess void content. A silicon carbide element tube furnace was used with thermocouple control for sin-

Jan 1, 1963

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By J. C. Sarace, S. M. Sze, C. R. Crowell

Thin films of tungsten 077 n-type germanium, silicon, and gallium arsenide were obtained by reacting tungsten hexafluoride with the semiconductor surface in an argom atmosplrere at temperatures between 325° and 400° C. Capacity-voltage, current-iloltage, and photoelectric measurements were used to investigate the characteristics of the tungsten -semiconductor diodes thus Produced. The junctions are shown to he very close to ideal Schottky barlp/ers with barrier heights measured with respect to the Fermi energy of 0.18, 0.65, and 0.78 1.1 jar W-Ge, W-Si, and W-GaAs, respectively. The electrical properties of the W-Si interface show no deterioration when heated to 1000°C in dry forming gas for 5 min. A theoretical value of the Richardson constant, A, appropriate to the semiconductor-hand structure has been used in evaluating the current-voltage characteristics. ThE W-Si surface-barrier diode was initially proposed for investigation because the eutectic temperature with silicon (1400°C) is much higher than that in the Si-Au system 1370°C).1 This would permit more flexibility in heat treatment and possibly provide greater reliability at elevated temperatures. The lower work function of tungsten (4.54 ev)2 compared with that of gold (4.78 ev)3 also suggested that a lower barrier height would be obtained with tungsten and hence a lower forward bias and lower minority carrier injection ratio for a given current density. The investigation was extended to include the characterization of W-Ge md W-GaAs surface-barrier diodes. The tungsten films have been produced by reacting WF6 with germanium, silicon, and GaAs surfaces in an argon atmosphere at temperatures from 300° to 500°C.4 This process is a very satisfactory alternative to the relatively difficult process of evaporating tungsten films in vacuo. To ensure an adequate electrical characterization of the tungsten-semiconductor interface, three types of barrier-height measurements have been performed. The mutually consistent results obtained lead to the conclusion that the tungsten-semiconductor junctions are indeed of the Schottky type. EXPERIMENTAL PROCEDURE The apparatus used for producing tungsten films is shown schematically in Fig. 1. It consists of an argon carrier gas line to which metered amounts of tungsten hexafluoride can be rapidly added. The mixture passes through a heated reaction tube containing the semiconductor slices and is exhausted to a hood. The argon is purified by passage through a 6-in. column of titanium turnings maintained at 800°C. The tungsten hexafluoride dispensing arrangement was designed by V. C. Garbarini and W. R. Bracht.4 A measured amount of liquid tungsten hexafluoride is injected into the argon stream and vaporizes. The mixture passes through a sodium fluoride absorption cell to remove traces of hydrogen fluoride, then into the nickel reaction tube. The tube is 12 in. long with an inside diameter of 1/2 in. The center section is heated by a furnace of the self-supporting wire-filament type. It was chosen for its rapid heatup and cooling. The wall thickness is 10 mils except for a 3-in. hot zone which is 30 mils thick to reduce thermal gradients along the length. The samples to be coated are placed on a sapphire plate and centered in this section. The tungsten is deposited with the following sequential steps: the loaded reaction tube is flushed with argon at a rate of 500 cu cm per min and heated to 370°C. Then 0.45 g of liquid tungsten hexafluoride is injected into the argon stream. The samples are held at this temperature for 2 min. The tube and samples are then cooled to room temperature and the samples removed. Tungsten films were grown on (111) faces of silicon and germanium polished with Linde A abrasive and lightly etched with HF-HNO3. The GaAs surfaces were (100) faces chemically polished with a H2SO4-H2O2 solution. The films have typical sheet resistances of 0.2, 8, and 15 52/0 when grown on germanium, silicon, and GaAs, respectively. After the tungsten deposition, ohmic contacts were alloyed on the back surfaces of the wafers. Ohmic contacts to the germanium and silicon were obtained by alloying Au-Sb at 370°C, ohmic con-

Jan 1, 1965

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge' in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole's time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a 'complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By Martin Weinstein

A technique is described for preparing finegrained lead telluride by ultrasonic agitation of a solidifying melt. Material prepared by this technique is dense and chemically homogeneous. N-type PbTe, containing 0.03 mole pct PbIz, has been made and its thermoelecCric Properties have been measured as a function of temperature. For comparison, the properties of similarly doped PbTe made by cold pressing and sintering, and by extrusion, have also been measured. The ultrasonically prepared material compares favorably with the others in its thermoelectric-efficiency factor. Comparison of compressive-flow curves for the three kinds of PbTe show that the ulhasonically prepared material has much superior ductility. The cleavage strength of the ultrasonic material is related to the grain size, D, by the Petch relation:Extrapolation to infinite grain diameter yields a fracture strength of 5000 psi for single-crystal PbTe. WHEN metals and semiconductors solidify in a mold they normally assume one of three cast structures illustrated in Fig. 1.' Solidification in a casting starts at the mold walls where a large number of fine crystals of random orientation can be nucleated to form the chill zone. Because of the anisot-ropy of the growth rate, those crystals whose direction of maximum linear growth is parallel to that of the heat flow grow faster and crowd out the crystals of less favorable orientation. A second zone, having a preferred orientation, called the columnar zone, thus forms adjacent to the chill zone. The speed of growth of the columnar grains will depend, in the case of limited undercooling of the melt, on the rate at which heat can be abstracted. The columnar zone can extend to the center of the casting, Fig. l(a), but it is frequently followed, in solid-solution alloys, by another zone of equiaxed randomly oriented grains in the central portion of the casting, Fig. l(b). The equiaxed structure in Fig. l(c) represents the completely grain-refined case where the equiaxed grain size is small. The third type of structure is the most desirable because it imparts a somewhat higher strength for all except high-temperature applications, it reduces segregation of the doping constituent, and it reduces the possibility of hot tearing (the separation of grains due to the melting of a low-melting point constituent in the grain boundaries). In order to obtain fine-grained castings, the nu-cleation frequency must be increased and grain growth must be restricted. Various techniques have been employed for obtaining this end, namely: rapid cooling, vibration, and inoculation of the melt. The success of these techniques depends upon the characteristics of the metal species and on factors controlled by heat transfer through the crucible walls. Recent studies2" have shown that the application of ultrasonic energy to the solidifying ingot is an extremely powerful tool in the improvement of the crystalline structure of metallic castings. Both the mechanical properties and homogeneity of the ingots are improved. Ultrasonic oscillations may affect the crystallization process by 1) permitting subcritical nuclei to agglomerate and thus form nuclei of sufficient size to cause crystallization, 2) changing the state of surface adsorption of various catalysts found in the liquid melt, 3) breaking pieces of solid from the solidified surface near the supercooled region thereby increasing the number of possible nuclei, 4) causing temperature fluctuations to occur in certain parts of the melt thereby increasing the supercooling at specific points in the liquid, and 5) decreasing the critical nucleus size by increasing the pressure at specific points in the melt.' Various investigators have concluded that the effectiveness of the ultrasonic oscillations results from cavitation which disrupts the growing solid-liquid interface The present paper describes the application of ultrasonic oscillations to the crystallization of the semiconductor N-type PbTe. The purpose of this study is to prepare crystalline

Jan 1, 1964

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By M. R. Geer, H. F. Yancey

John Grifien (Pittsburgh)—I wish to congratulate the authors on this paper, which, I am sure, will promote a clearer conception of the various criteria which have been advanced as measures of coal-cleaning performance. Their clear descriptions of the more important criteria that have been advanced and explanations of their meaning and application have been sorely needed and, if widely promulgated and followed, should remove much of the confusion which, heretofore, has been evident. I suggest that much of this confusion has also arisen from lack of common agreement as to the exact meaning of the words and terms used in our discussions of this subject. I am sure I have been equally guilty in this respect and suggest it is time that we select a committee to study vocabulary as well as criteria, so that common understanding and agreement can be had. Thus, I suggest, that the title of this paper should have used the words "coal-cleaning performance" and not "coal-washery performance." My understanding is that "washery" refers to a complete plant and it has additional functions to that of coal-cleaning, such as control of size, moisture, etc. Also, I do not agree with the authors that the formulas given in their paper, the Fraser and Yancey formulas, are necessarily the only ones that can be called efficiency formulas. When a dictionary is consulted one realizes that the words "efficiency" and "efficient" have not precise meanings but only very general ones and must be further defined for each particular use, if they are to have any precise meaning. To my mind, the first of the Fraser and Yancey formulas given should never be used as expressing "efficiency" alone but only by the fuller phrase which truly expresses the kind of efficiency it states, which is "coal recovery efficiency." For complete clarity we then need only define "coal" for the particular circumstances under which the formula is used. This would recognize the fact, fully explained by the authors, that the limits in coal qualities imposed by the market have imposed a factor—and a variable factor—which has influenced any answer obtained by this formula. Such a procedure makes it entirely practical and logical to use the values of any of the qualities of coal—ash, sulphur, phosphorus, specific gravity—or a combination of them to define what is coal for that particular use of the formula. Further, it is clear to me that the criteria to be used must be dictated by the objective in view and the use for which the data are obtained. The authors clearly point out that the Fraser and Yancey coal-recovery efficiency formula is influenced by three factors, "one is determined by the coal, one is dictated by market or use conditions, and one is an inherent characteristic of the cleaning unit itself." The formula which uses the inverse of misplaced material as a measure of efficiency is also a coal recovery efficiency formula and is influenced in like manner by these three factors. As the authors point out, both are useless in obtaining data which enables a direct and valid comparison of the performance of a given cleaning unit on two coals where the other two factors vary or of the performance of two or more cleaning units of different types unless the values of the other two factors are identical. Much of the confusion in our discussions of and literature on coal cleaning has come from failure to understand clearly this fact. Many such comparisons have been made from which erroneous conclusions have been drawn. I am, therefore, particularly glad to see the authors' emphasis on 4?-1e criteria which indicate the "sharpness of separation. I feel that these are the essential criteria

Jan 1, 1952

By Leo Horvitz

Microanalysis of near-surface soils for hydrocarbons is the basis of a method for locating gas and oil deposits. To substantiate this technique, evidence of vertical migration of hydrocarbons from petroleum accumulations is presented. Tabulated data relevant to hydrocarbon surveys conducted in several petroleum provinces are included. PEROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer' in Germany and by Sokolov in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas. Since 1936 work on petroleum exploration techniques of this type has been going on in this country. However, instead of determining hydrocarbon content of soil air collected in the field, investigators analyze samples of the soil itself for adsorbed and occluded hydrocarbons, which are released by suitable treatment and found in larger amounts than are the quantities reported for soil air. Difficulties often encountered in collecting gas samples in the field, moreover, are eliminated when soil is used as the sampling medium. Field Procedure: Sample locations are first surveyed over the area to be investigated. Care is taken to locate the stations at considerable distances from roads, pipelines, drilling wells, and other sources of contamination. The borehole pay be dug with a bucket-type hand auger or with mechanical drilling equipment. Lubricants are avoided in either case. When the desired depth is reached, a sample is brought to the surface, placed in a pint glass jar or can, and securely sealed. Sample containers are carefully labeled and delivered to the analytical laboratory. Generally a satisfactory sampling depth range is 8 to 12 ft. In some regions, however, satisfactory data are obtained from samples collected at much shallower depths. Such is the case, for example, in areas of west Texas where the limestone and caliche near the surface occlude hydrocarbons and prevent their rapid escape to the atmosphere. In carrying out broad reconnaissance surveys in search of large features, considerable time is saved by first taking samples one-fourth to one-half mile apart along profiles about one mile apart. If the analytical data indicate a hydrocarbon anomaly of interest, additional samples are taken to produce a more dense and uniform sampling pattern within the interesting area. This sampling program is particularly adaptable to areas that are sectionized. In areas covered with a network of roads, sampling along these roads facilitates the reconnaissance survey. Actual sampling density used depends upon areal extent of features expected. When flanks of piercement-type domes where accumulations may be only several hundred feet wide are sampled, stations are often no more than 200 ft apart. Analytical Technique: Of the hydrocarbons composing petroleum, only the more volatile would be expected to reach the surface of the earth. The analytical technique, therefore, was developed to determine only those constituents that exert a vapor pressure at room temperature. Actually, in near-surface soils, only a very small part of the hydrocarbons are heavier than pentane. Details of the analytical technique have previously been reported. Only a brief description of the methods will be presented here. A weighed portion of the sample, about 100 g, is first treated with an aqueous solution of copper sulphate and then with phosphoric acid in a partial vacuum. The copper sulphate prevents the reaction of the acid with carbides that may be present because the sample has been contaminated by auger particles. Such a reaction may produce spurious methane. The role of the acid is to decompose any carbonates present, thereby helping to release the hydrocarbons. The carbon dioxide is removed with potassium hydroxide and the flask containing the

Jan 1, 1955

By T. S. Plaskett

A striated structure perpendicular to the growth axis was observed by the copper-decoration tech-nique in dislocation-free, .float-zoned silicon crystals. The striations, which were spaced about 100 p apart, fitted the relationship d = f/u , where d is the spacing, f is the growth rate, and u is the crystal rotation rate. Each stria was resolved into an UNDOPED silicon crystals pulled from quartz crucibles by the Czochralski technique usually exhibit a striated structure perpendicular to the growth axis.'-' This structure has been attributed to oxygen segregation, with the oxygen being introduced from the quartz crucible. If the crucible is rotated, the level of oxygen contamination has been reported as high as 10° atoms per cu cm.10 These striations are similar to solute striations commonly observed in doped Czochralski-grown crystals. The periodic nature of the striations is caused by a periodic variation in the growth rate",12 which is attributed mainly to thermal gradients in the melt.13 A finer striated structure14 attributed to constitutional supercooling is sometimes observed between the coarse striae. The oxygen striations have been observed by infrared transmission techniques,' by the copper-decoration technique,' by X-ray diffraction microscopy,6-8 and by 9 p absorption measurements3 on crystals pulled from the melt both with and without dislocations. In this investigation float-zoned dislocation-free crystals were examined by the copper-decoration technique. The level of oxygen for float-zone material is less than 1016 atoms per cu cm the lower limit of detection by 9 p absorption measurement. EXPERIMENTAL TECHNIQUE The crystals were grown by the float-zone process with the rf heating coil outside of the quartz envelope containing the silicon. All float zoning was done under an atmosphere of purified helium. The Dash technique15 was used to grow the crystal dislocation-free. This involves growing the crystal initially with a diameter between 2 and 3 mm and at array of starlike precipitates of copper. The strucLure was not .found at the surface tor a depth of about 1.5 mm, or in a region of similar width ahead of a dislocation network. The structure is postulated to consist of vacancy clusterings or dislocation loops. very rapid rates, about 20 mm per min, for a distance of about 3 cm. The diameter of the crystal is then increased to the diameter of the source of silicon, which in this case was about 19 mm. Because of the arrangement of the apparatus, the zone was passed downward rather than upward, contrary to the standard float-zoning practice. Also, the source was rotated rather than the seed. ziegler17 has made dislocation-free crystals by a similar technique but has passed the zone upwards. The starting material was zone-refined and had a p-type resistivity of 150 ohm-cm. The major impurity was boron; the total impurity excluding the boron was reported by the supplier (Dow-Corning) to be typically less than 2 x 1013 atoms per cu cm. The crystals were examined by the Dash copper-decoration technique18'19—a method in which about 10" atoms per cu cm of copper are diffused at a temperature between 900" and 1000°C into silicon which is then quenched to room temperature. On quenching, the copper precipitates on crystalline defects which are then visible when viewed by transmission infrared microscopy. The photomicrographs shown were taken either of the infrared image tube screen or directly on infrared film. All sections prior to decorating were chemically polished and, for some sections, given a sirtlZ0 dislocation etch-pit examination. After decorating, the samples were mechanically polished. RESULTS A photomicrograph, taken in transmission of a decorated cross section, is shown in Fig. 1. The portion of the section shown is near the surface of the crystal. The entire cross section showed no dislocation etch pits after being given a Sirtl etch treatment. It is seen that the copper precipitated randomly. Each precipitate, as has been reported by others, was found to have a starlike structure.

Jan 1, 1965

By Wallace W. Wilson

The Cook Ranch Field produces from a very permeable lens of Cook Sand of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The field was discovered in 1926, and has been operated with low pressure gas injection since July, 1927, one of the first such projects in Texas. Cumulative recovery to Dec. 31. 1950, was 14,701,131 bbl of crude oil, an average of 1,013 bbl per acre-ft of oil rection. and 72.5 per cent of the oil originally in place. Analysis of the reservoir performance indicates that grav-ity drainage has been an important factor in the producing mechanism. The high permeability and uniformity of the reservoir were extremely Favorable tor this type of operation. INTRODUCTION The Cook Ranch Field is the largest of a number of relatively small, shallow producing areas near .Albany, in Shackelford County, Texas. This field is one of the first to be operated by gas injection in Texas, and probably is the most successful low pressure gas injection project ever attempted. The field is owned entirely by Koeser and Pendleton, Inc., and Continental Oil Co., and has been operated by Roeser and Pendleton, Inc., since it was discovered. This study has been made possible through the cooperation of Roeser and Pendleton, Inc.. in making availahle a remarkably complete set of records covering all phases of their operations. The purpose of this paper is to present a summary of the history of the operations through Dec. 31, 1950, and to analyze some of the factors which appear to be responsible for the success of the project. Information concerning the physical plant and the early gas injection history has been presented in an earlier paper.' RESERVOIR CHARACTERISTICS production in the Cook Ranch Field is from a large lens of Cook Sand. of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The average dip of the sand body, as shown in Fig. 1. is only about 50 ft per mile to the northwest. The reservoir has an area of 930 acres and contains 15,512 acre-ft of Sand, consisting of about 14.512 acre-ft of produc-tive oil zone. and an estimated 1.000 acre-ft of primary gas-cap. The iso-pachous map (Fig. 2) was prepared from drillers' logs. Recent coring in the field has proven these logs to be quite accurate. The productive limits of the field are defined by shale on all sides but the southwest where a small zone of edgewater was encountered. This water does not appear to have encroached into the reservoir, and water production has been small. A smaller producing area to the south of the Cook Ranch Field also produces from the Cook Sand. but is separated from the reservoir under consideration by a band of shale. The sand consists of well sorted, coarse grained. rounded and subangu-lar quartz fragments. very poorly cemented. The analysis of 46 chip-core samples from two recently completed test wells indicates a range of porosity values between 12.5 and 28.2 per cent. wit11 an arithmetic average of 24.0 per cent. Air permeability values range between 50 and 2,300 md, with an arithmetic average of 1.200 md. The reservoir where cored is a Solid sand body. with no discernible major shale breaks or impermeable streaks. Vertical permeability appears to be of the same magnitude as the horizontal permeability. A core of the Cook Sand was cut ill the smaller field to the south, using lubricating oil as drilling fluid. The connate water content of the sand in this core was found to average about ten per cent, and the porosity and permeability were comparable with the values reported above. No analysis was made of subsurface or recombined hydrocarbon samples,

Jan 1, 1952

By D. A. Kraai, S. Floreen

The effect of 1 to 50 ppm S on the ductility of nickel at 800° to 1400°F was studied. Results at each temperature showed a decrease in the reduction of area from approximately 95 to 5 pet over the sulfur range studied. Ductility varied with grain size, but only to a minor extent relative to the sulfiw effect. The effects of sulfur were completely offset by the addition of small amounts of magnesium. The results indicate that the "hot-short" loss in ductility is not an inherent property of nickel. Some possible mechanisms which cause the loss in ductility are described. MANY metals or alloys that normally possess high ductility exhibit a ductility loss at intermediate temperatures. This loss in ductility is often called "hot-shortness". Numerous examples of this phenomenon have been reported in the literature. Much of this work has been reviewed by McLean1 and by Rhines and Wray.2 To date there is no fully satisfactory explanation of the cause of this intermediate-temperature hot-shortness. It is generally recognized that impurities, and particularly impurities that form low-melting phases, can cause embrittlement. Examples of hot-shortness have been reported, however, where there were no obvious impurities present which would lower the ductility. Thus there has been some basis for believing that hot-shortness is an inherent property, and that even the purest metal would display a hot-short loss in ductility. This latter hypothesis was recently put forward by Rhines and wray2 based on studies of nickel and nickel alloys. In the discussion of this paper, however, Guard noted that high-purity nickel showed no hot-shortness.3 Thus there is reason to doubt whether pure nickel, or by inference any other pure metal, will inherently exhibit hot-shortness. The present work was initiated to determine the extent to which hot ductility was sensitive to very small amounts of an impurity element. If it could be demonstrated that hot-shortness could be induced by only minor amounts of an impurity, then it might be argued that hot-shortness in general is an impurity effect, and not a fundamental property of pure metals. The particular impurity studied was sulfur in nickel. The deleterious effects of sulfur are well- known. It is also well-known, and will be shown below, that additions of magnesium will render sulfur innocuous. When no such refining agents are added, however, the Ni-S system is a very useful one for studying the influence of small amounts of impurities. EXPERIMENTAL PROCEDURE Two heats containing -24 ppm S were vacuum-melted and small amounts of magnesium were then added under an argon atmosphere. These alloys were used to show the effectiveness of the normal magnesium treatment in overcoming the influence of sulfur. A second series of alloys with a sulfur range of 1 to 50 ppm was then prepared by vacuum melting nickel in alumina crucibles. No elements, such as magnesium, which tend to combine with sulfur were added. The higher sulfur contents were attained by adding nickel sulfide. Lower sulfur contents were prepared using a method in which the melt was oxidized under vacuum to produce the reaction S + 2O = SO2 These heats were subsequently deoxidized with carbon. Ten- to twenty-pound ingots were cast of all of the alloys studied. The compositions are given in Table I. The ingots were forged and hot-rolled to 3/4-in. bar. They were then annealed at either 2000" or 1600°F to produce different grain sizes. One-quarter-in.-diam tensile specimens were machined from the bars. These were tested at 800°, 1000o, 1200°, and 1400°F. The specimens were held at temperature approximately 45 min before testing. The strain rates were 0.005 min-1 to yielding, and 0.05 min-' after yielding. No extensometers or gage marks were placed on the specimens because the higher sulfur heats tended to fracture at the knife-edge indentations or gage marks. The properties measured were ultimate tensile strength and reduction of area. The analytical technique for determining sulfur at low levels was that developed by Burke and Davis.4 They reported a standard deviation of 1 ppm at an average sulfur level of 4 ppm in NBS standards. A standard deviation of 3 ppm is probably more realistic for the alloys used in this investigation considering the possibility of some segregation in the ingots. RESULTS A summary of the tensile results is given in Table I. As shown in the table, both heats to which

Jan 1, 1964

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1' the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man' permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if' the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a'Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a'Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By P. B. Mee

The secondary re crystallization behavior of two vacuum-melted, nominally 3 pct Si-Fe alloys has been studied, one alloy being produced from pure electrolytic iron and semiconductor-grade silicon and the other from commercial-purity hot band. The vacuum-melted and vacuum-remelted alloys were found to develop {110}(hhl) and {lll)(hkl), respectively, on annealing in high vacuum and {100}(0kl) and {11l}(hkl), respectively on annealing in pure hydrogen of dew point, < — 60°C. H2S doping of the hydrogen or annealing in commercial argon was found to effect a reversal for the vacuum-remelted alloy from (111) to (100) secondary recrys-tallization, while prolonged vacuum annealing at 2 x 10-6 Tow resulted in a tertiary re crystallization from (111} to (110). The growth selection of the {lll}(hkl) component was found to be governed predominantly by the {111}/planar misorientation, the maximum deviation of the resulting secondaries being 5 deg. It is considered that the driving force for {111}(hkl) secondary recrystallization arises from the preferential lowering of ?111, possibly by phosphorus or nitrogen diffusion, just as oxygen and sulfur under certain conditions have been found to preferentially lower ?100. When heavily cold-rolled metals are annealed at high temperatures, primary recrystallization usually occurs rapidly and may be followed by considerable grain growth. However, in the presence of a fine dispersion of inclusions1"3 or with a strong matrix preferred orientation4&apos;&apos; the matrix may be stabilized and a secondary recrystallization may then be effected. Also, in vacuum-melted Si-Fe it has been shown possible to develop {100}(001) and {110}(001)6 surface energy driven secondary recrystallization textures. Further, it has been found that, on annealing very pure metals, grain growth normally ceases when a grain size approximately twice the strip thickness is acquired, due to the formation of V-shaped thermal grooves which result in an equilibrium being set up between surface and grain boundary stresses. If, however, a surface energy difference ??s, exists between adjacent grains (of the order of a few percent of the grain boundary energy ?b), then according to Mullins8 a secondary recrystallization may be effected, since the grains having lowest ?s would grow at the expense of their higher-energy neighbors. For clean bee metal surfaces ?110 should be lowest; however, for 3 pct Fe-Si (100) secondary structures have frequently been developed and have been attributed by Walter and Dunn9 to an alteration of the relative surface energies due to the preferential chemisorption of oxygen on (100) planes. Kohler,10 however, indicated that this reversal may be achieved by employing minute quantities of highly polar compounds in the annealing atmosphere, i.e., sulfur compounds, in par- ticular H2S being beneficial in (100) growth. This work has been verified by Kramer" using {100)/{110} bicrystals, while Mager12 demonstrated the importance of sulfur diffusion within the strip. Detert13 has intimated that carbon may be responsible for the preferential lowering of ?110 although no direct evidence has appeared yet to support this supposition. It must , be appreciated that the above-mentioned examples of surface energy driven secondary recrystallization were obtained with very pure vacuum-melted materials with oxygen contents (which is now known to be a critical factor") less than 35 ppm. During the course of a textural study on Si-Fe it has been found that under certain conditions (111) secondary recrystallization can be obtained by what is believed to be a surface energy growth selection mechanism. The purpose of the present paper is to briefly describe this result and to try and postulate the possible causes. EXPERIMENTAL Two vacuum-induction-melted, nominally 3 pct Si-Fe alloys were produced, one from pure electrolytic iron and semiconductor-grade silicon designated A and the other from commercial-purity hot band, designated B.

Jan 1, 1969

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,&apos; is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.&apos; Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956

By M. D. Arnold, H. J. Gonzalez, P. B. Crawford

A method is presented for estimating the effective directional permeability ratio and the direction of maximum and minimum permeabilities in anisotropic oil reservoirs. The method is based on the principle that production from a well in an anisotropic reservoir results in elliptical isopo-tentials about the well, rather than circular. Bottom-hole pressure data from three observation wells surrounding a producing well are required to apply the method. The method involves fitting field pressure data to a set of general charts of isopotentials and making a few simple calculations until a solution is found. The method is based on a steady-state equation for homogeneorrs fluid pow. In addition to the method, a brief discussion of the theory underlying it is presented. INTRODUCTION The existence of a different permeability in one direction than another in oil reservoirs has been mentioned in several papers. Hutchinson&apos; reported laboratory tests on 10 limestone cores and pointed out that one-half of them showed significant, preferential, directional permeability ratios, the average being about 16:1. Johnson and Hughesz reported a permeability trend in the Bradford field in the northeast-southwest direction with flow being 25 to 30 per cent greater in that direction. Barfield, Jordan and Moore -eported an effective permeability ratio of 144:1 in the Spraberry. Crawford and Landrum4 showed that sweep efficiencies could often vary by a factor of two to four, and sometimes considerably more, due to variations in flooding direction and patterns in anisotropic media. These findings indicate that the poss&apos;bility of anisotropy may be worthy of consideration in the development of an oil field. In considering this, it should first be determined if anisotropy exists. If it does, the direction of the maximum and minimum permeabilities and the ratio of their magnitudes are quantities which can be of value in planning the most efficient well-spacing patterns. Past methods of determining these quantities have included analysis of oriented cores and analysis of flooding performance of pilot injection patterns. In recent work, Elkins and Skov5 resented an analysis of the pressure behavior in the Spraberry which accounted for anisotropic permeability. This work was based on the transient pres- sure distribution in a porous and permeable medium, with the solution expressed as an exponential integral function involving rock and fluid properties. The purpose of this study is to provide a method, based on steady-state equations, of estimating the direction and relative magnitude of permeabilities in an oil reservoir from field pressure data and well locations only. The method presented is based on work by Muskat6 which shows that Laplace&apos;s equation represents the steady-state pressure distribution for homogeneous fluid flow in homogeneous, anisotropic media if the co-ordinates of the system are shrunk or expanded by replacing x with it is desirable that data be obtained early in the history of a field because knowledge of an anisotropic condition would allow new wells to be spaced in such a manner that reservoir development and subsequent secondary recovery programs could be planned more efficiently. THEORETICAL CONSIDERATIONS A brief discussion of the theoretical basis on which the graphical solution was developed is presented in this section. Muskat&apos;s two-dimensional6 olution for the pressure distribution in an homogeneous, anisotropic medium with an homogeneous fluid flowing can be algebraically manipulated to show that the isobaric lines are perfect ellipses. The ratio of the major axis to the minor axis, a/b, is related to the permeability ratio, k,/k,, as follows. alb = dk,/k,--...........(1) It can also be shown that the pressure varies linearly with the logarithm of the radial distance from the producing well. However, the gradient along any ray is a function of the orientation of that ray, and a ..xiable is present when anisotropy exists which cancels out for a radial (isotropic) system. For a system such as that described, a dimensionless pressure-drop ratio was developed which is completely independent of the actual magnitude of the pressures. This was done by arranging Muskat&apos;s solution in such a way that aIl variables cancelled out except k,/k, and well positions. However, this solution depends on having a co-ordinate system with axes coinciding with the major and minor axes of the elliptical isobars. Thus, it was necessary to introduce a co-ordinate system rotation factor. The two unknown variables are then k,/k. and 0, and the two measured dimensionless pressure-drop ratios are related to the unknown variables as follows.

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958