Search Documents

By K. Heindlhofer

ESTIMATES of the "plasticity" of a metal are commonly deduced from three types of test-tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this differ-ence in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and there-fore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of tem-peratures, or for a series of metals at one temperature, because the propor-tion of the total resistance of the metal to the test contributed by the

Jan 1, 1934

By S. M. Matthews, D. J. Maconochie, L. G. Alexander, V. H. Tillmann

Case studies of the behaviour of large open stopes at the New Broken Hill Consolidated Mine, Broken Hill and the CSA Mine, Cobar, N.S.W. are considered. Deformations were measured by multipoint rod extensometers in sufficient detail to note the phases of rock behaviour, from intact through to rock-fall. In one case readings were obtained from a zone of stress failure in which two bumps, felt as ground tremors, occurred. In this case noise and stress were also monitored. Deformations were analysed in relation to previously measured in situ rock stress, and conclusions drawn about the degree of conformity to, and the areas of departure from, elastic model behaviour. Attempts to describe the growth of instability utilize reduction factors of the apparent modulus, a magnification factor for the apparent Poisson's ratio, and a correlation between progressive noise count and displacement. Monitoring itself is seen as an aid in determiing the final dimensions of stopes and pillars. One large stope, of intermediate dimension 80 m, was mined essentially without change of plan, whereas a change in mining plan was necessary in other stopes. Aspects of interest to mine planners, and areas where futher research is needed, are indicated.

Jan 1, 1981

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By John Henry Harden

With imperfect instruments it is impossible to make accurate surveys; the results are inaccurate maps, with their attendant consequences. The design of the writer is to describe an improved form of tripod head, and certain defects in an English transit and a miners' dial, with the method taken to remedy the defects of the transit. When the present transit superseded the surveyor's compass, there was one special objection brought against it, and with some show of reason ; namely, that the tripod of the compass with its ball and socket motion, allowed a quicker levelling-up (and, consequently, more work) than mas possible with the transit. To this objection it was replied, that the ball and socket would not allow the instrument to be levelled with the same degree of precision that could be attained with the levelling screws, and that if time was sacrificed greater accuracy was attained. Nevertheless, it is a wellknown fact that in this country, and especially in England, the compass or miners' dial holds its ground solely from its rapid adjustment. Ever since the introduction of the transit, efforts have been made to give to this instrument the same facility of levelling possessed by the compass or dial, and the same means have been tried, i. e., a ball and socket motion, since a modification of this in some form was the only method that would answer. The upper part of a transit is, however, much heavier than the corresponding parts of a compass, and, therefore, requires more binding power, which cannot be obtained with an ordinary ball and socket joint. It has been a study with instrument-makers to combine the facility of these two tripods —the quickness of the ball and socket with the steadiness and accuracy of the screws; but in all attempts in this direction the ball and socket of the compass has been literally followed, the entire stability of the instrument depending upon the friction of the ball in its socket. There is great need for a tripod that can be more easily manipulated than the present form, for it rarely happens that an engineer has a level surface on which to set his instrument, and very often

Jan 1, 1879

By O. B. Hopkins

There was no noteworthy development in the oil industry in Peru during 1933 and all activities were restricted to the producing fields. The output of the country increased above that of previous years but there still remained a substantial shut-in production at the close of the year. The total production during 1933 is estimated at 13,259,891 bbl., of which the International Petroleum Co., Ltd. contributed 11,205,-362 bbl. A relatively small amount of new drilling was undertaken during the year. The International completed only one new well although a number of the old producers were reworked and deepened. Comments on Tables There are four oil districts in Peru, as shown in Table 1, although only three of these are now being operated. The exhausted Pirin field was abandoned eight years ago. La Brea-Parinus.—The La Brett-Parinas fields are on the property of the International Petruleum Co., Ltd. in the westernmost part of Peru. These fields include a number of producing districts that are defined by complex fault blocks associated with anticlinal folds. Data covering all the items listed in the table are not available on these fields but can perhaps be supplied in part in the future. Lobitos and Restin.—These two fields belong to the Lobitos Oilfields Limited and are near the coast, 10 to 20 miles north of the La Brea-Parinas fields. According to the Department of Mines and Petroleum of Peru, 311 wells at Lobitos and 197 at Restin had been drilled to the end of 1927. Since that date there has been enough drilling to increase moderately these figures. The depth of wells is not available but it is believed that their average depth is slightly greater than in the La Brea-Parinas area. The productive horizons are of Eocene age. zorritos.—The Zorritos field is the northernmost in Peru and is operated by the Establecimiento Industrial de Petroleo de Zorritos. The field is on the coast about 70 miles north of Lobitos. The number of wells drilled in this field to the end of 1927 was 343, according to the Department of Mines and Petroleum of Peru. The depths of these wells are reported to range from 300 to 700 ft. The largest wells do not produce

Jan 1, 1934

By Edward W. Parker

At the Cleveland meeting of the Institute, October, 1912, I had occasion to call attention to the general though erroneous impression that the principal mining activities of the United States lie west of the 100th meridian of longitude. Few, I believe, realize that the States east of the Mississippi river, which comprise only 28.8 per cent. of the total area of the United States, exclusive of Alaska, contribute about two-thirds of the total mineral production, computing by values. In 1910 the percentage of the production credited to the Eastern States was 67; in 1911 it was 65. When I have, with becoming modesty, ventured to speak of these comparisons, I have usually been met with the rejoinder, " But you include coal." I surely do, for whereas coal (m petroleum, as natural gas, as limestone) is not in the strictly technical definition of the word, a " mineral," it is legally mineral, is certainly a mineral substance, and contributes by far the largest tonnage and approximately one-third of the total value of all mineral products. The production of coal-mines in 1911 weighed approximately 500,000,000 tons. In 1912 it exceeded that record by nearly, if not quite, 50,000,000 tons. According to H. D. McCaskey, of the U. S. Geological Survey, the total weight of all the metallic ores mined in the United States in 1911 was 105,000,000 tons (a little more than one-fifth that of coal). In 1910 Mr. Lindgren estimated the total weight of all metallic ores at 120,000,000 tons. The products of the quarries, clay-pits, oil-wells, phosphate-mines, and other non-metallic products, taken all together, did not in 1911 weigh in excess of 300,000,000 tons, so that the output of coal exceeds by 25 per cent. the combined tonnage of all other mineral products. The coal-mines give to

Jan 1, 1914

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By Herbert Clark Hoover, Lou Henry Hoover

We give the following brief notes on early works containing some reference to mineralogy, mining, or metallurgy, to indicate the literature available to Agricola and for historical notes bearing upon the subject. References to these works in the footnotes may be most easily consulted through the personal index. GREEK AUTHORS.-Only a very limited Greek literature upon subjects allied to mining or natural science survives. The whole of the material of technical interest could be , reproduced on less than twenty of these pages. Those of most importance are : Aristotle (384-322 B.c.), Theophrastus (371-288 B.c.), Diodorus Siculus (1st Century B.c.), Strabo (64 B.c.-25 A.D.), and Dioscorides (1st Century A.D.). Aristotle, apart from occasional mineralogical or metallurgical references in De Mirabilibus, is mostly of interest as the author of the Peripatetic theory of the elements and the relation of these to the origin of stones and metals. Agricola was, to a considerable measure, a follower of this school, and their views colour much of his writings. We, however, discuss elsewhere1 at what point he departed from them. Especially in De Ortu ct Causis does he quote largely from Aristotle's Meteorologica. Physica, and De Coelo on these subjects. There is a spurious work on stones attributed to Aristotle of some interest to mineralogists. It was probably the work of some Arab early in the Middle Ages.[ ]

Jan 1, 1950

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By J. O. Nomland

Bahrein 'Island.—In 1936 the Bahrein Petroleum Co. continued drilling additional wells to further increase production. In all, 39 flowing wells have now been finished and five others are drilling. A second well has been deepened for prospecting the deeper horizons but has not been successfully completed as a commercial producer. In addition, a well has recently been drilled near the eastern limit of the producing area for edge-water observation. The present system places wells 3000 ft. apart in a rhombic grid, or about one well to 179 acres. The total production for the year was 4,644,635 barrels. It is expected that refinery capacity of 20,000 bbl. per day will have been completed by July, 1937. A new permanent and enlarged camp with office buildings is being built. A new hospital has been constructed and two additional medical men have been added to the staff. Saudi Arabia.—In eastern Saudi Arabia, the California Arabian Standard Oil Co. has continued with the program of prospect drilling started in 1935. After the gas encountered in Dammam well No. 1 had been successfully shut off, it was completed as a small flowing well of 51" gravity oil. Dammam No. 2, which had been started in 1935, tested 3840 bbl. of approximately 50" gravity oil from a depth of 2175 ft. Dammam No. 5, before being deepened for prospecting lower productive horizons, encountered a gas zone producing 30 million feet. Five other wells on the Dammam dome are in various stages of drilling or completion. Most of these have been located principally to outline the productive area and the various producing horizons of the structure. An extensive program of geological work is being continued. In June, 1936, a well was started on the El 'Alat structure about 25 miles northwest of the Dammam development. Although various tar showings have been reported, the well has not yet, at 2518 ft., reached the depth at which it has been thought that productive horizons might be encountered. A prospect well is being drilled by the Kuwait Oil Co. (jointly owned by Gulf and Anglo-Iranian Oil Companies) in the Sheikdom of Kuwait. The well is near Bahra, a few miles north of Kuwait Bay and about 240 miles northwest of El 'Alat. To date no favorable results at depth of about 6000 ft. have been reported.

Jan 1, 1937

By Oliver C. Ralston, Foster Fraas

Electrostatic methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to bene-ficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollas-tonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. The Separator The separator used in these tests is of the nonhomogeneous field type shown in Fig Ia. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll."

Jan 1, 1949

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,' from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

By Tribhawan N. Srivastava

The Henderson Mine started production in 1976 utilizing a unique, push-pull, mine ventilation plan. As the mine expands in size, the mine ventilation requirements will increase and a more comprehensive system for maintaining ventilation will be needed. A computer simulation study was completed and has resulted in a revised, systematic, mine ventilation plan which is being implemented as mine development proceeds. Based on the computer simulation study, the new ventilation plan takes into account mining of the orebody simultaneously from both the 8100 and 7700 production levels. Present experience and empirical data indicate that volumes of air needed to adequately ventilate both production levels cannot be obtained utilizing the existing mine layout. The total volume of air needed for the mine excluding haulage tunnel will increase from 708 m3/s (1 500 000 cfm) to 1652 m3/s (3 500 000 cfm), thus a new No. 5 exhaust shaft and connecting drifts are being developed to expand the mine ventilation system to service both production levels. The original ventilation plan for the 7500 haulage level was to bring air from the No. 2 and No. 3 intake shafts and exhaust it through the 94X raise to the 8035 exhaust level and then through the No. 1 exhaust shaft to surface. Control of air volumes in loading drifts was initially planned to be achieved by air doors and air curtains. Air doors on the 7500 level require large cutouts, expensive installations and constant maintenance. The computer simulation study indicates that air- flow in the 7500-level production drifts can be con- trolled exclusively by air curtains which are less expensive to install and more effective in regulating airflows than air doors. Air from the 7500 level can be exhausted through a new raise to the new 7635 exhaust level and then through the new No. 5 exhaust shaft.

Jan 1, 1982

By F. Z. Schellenberg

Systematic exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam's perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65' to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent. at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the dip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins—the general rise northeastward at 20 ft. per mile, from 100 ft. below sea-level at the low point near the SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant's charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jan 1, 1911

By Edwin C. Eckel

The title of this study may fairly lead to misunderstanding unless its basal viewpoint is explained at the start. There is of course no chance of misunderstanding the term strategic minerals-for some years past it has been rather generally used to cover those mineral supplies, important for war use, which do not occur in adequate amount on the territory of the Power under consideration. Even here, however, I might add a note of warning. It is commonly understood that the list of strategic minerals will vary, according to what country we are considering; but it is rarely understood, even in Staff studies, that it varies equally according to the particular adversary we happen to be considering. In the present study I have stated the definition in the broadest possible terms, and have at this stage purposely avoided limiting it to any one country or war situation, with the express purpose of being free to bring out certain implications which are commonly, if not always, overlooked. The more important opportunity for misunderstanding is, of course, that my views on the phenomena war and peace do not coincide with those currently fashionable, particularly in advanced intellectual circles. For we must face the fact that for a decade past the natural reaction from war conditions has shattered the public mentality so completely that our public discussions of such questions have very little relation to fact; they are excursions into ideal rather than Realpolitik. And as such they serve merely to prevent public discussion or accept-

Jan 1, 1932

By Theo B. Comstock

In the summer of 1877, the writer led a party of four young men from Cleveland, Ohio, by way of the Great Lakes, to Prince Arthur's Landing (now Port Arthur), at the northwest corner of Lake Superior, thence, via the Dawson route and side journeys, as far as Cross Lake. It was the original intention to pass down the Pigeon river to its mouth, but the loss of one member of the party for six days in the forest, added to other obstacles, made it necessary to turn back. A well-filled note-book, together with illustrative collections, were sunk beyond recovery at the head of the Maligne rapids by the breaking of a tow-line, and two of our number (including myself) narrowly escaped drowning. I had, probably, obtained information of considerable economic value, but the necessity of travelling nearly 125 miles for provisions (excepting a meagre supply kindly furnished us by a Canadian government gang whom we fortunately met), rendered further note-taking impossible. Until now, such results of this expedition as could be recorded . from memory have gone unpublished, because of my inability to make them serve any useful purpose. The trip of the Institute to Vermilion Lake, only a few miles south and east of our turning point, gives some little excuse for presenting the following lines at this time. The ridge back of Port Arthur, Ontario, which follows approximately the course of the Lake Superior shore line, brings up the slates and accompanying strata through which the silver and gold veins of that region have penetrated. The interior district, hack from the lake, may be briefly described as a glaciated area, having its general drainage less modified by erosion than by the original structure. This statement, however, must be somewhat qualified with reference to minor details, which all bear the unmistakable impress of the ice-flow and its recession. In many respects there is much in this tract to remind one of the Sault Ste. Marie topography, excepting that the granitic character of the rocks is here largely replaced by fissile strata. The Kaministiquia river cuts through several of the parallel folds,

Jan 1, 1888

By E. I. Salkovitz, F. W. von Batchelder

AS Slawson1 and others have already shown, from a geometrical view twinning in the diamond structure may be considered as a reflection across a (111) plane or as a reflection across a (112) plane. An analysis by Ellis and Treuting2 showed that the twinning plane must be the (111) plane, but that a twin might have lateral boundaries along (112) planes. Earlier Slawson1 and Ellis3 had shown that only (111) twinning was present in diamond and germanium respectively. Since an ingot of silicon, 1 in. in diam and 1 1/2 in. long, prepared from Dupont silicon to which 0.2 pct Be had been added was available, it was examined for twinning. The ingot had been cooled slowly from the bottom. A section 1/16 in. thick was ground off from the bottom and then the ingot was sliced vertically through the center. Spectrographic analysis indicated only faint traces of iron and silver, in addition to the beryllium. The sample was first etched with a hot solution of 10 pct NaOH in water.and photographed. Back-reflection Laue patterns were made of the vertical and horizontal sections in the regions designated in Fig. 1. Orientations were obtained for each twin using the Greninger technique. Several regions of the same orientation were found; thus regions A and K were identical, similarly N and P, and C, G, J, and L. Knowing the angles between the traces of the twinning plane on the surface and the specimen axis, the indices of the twinning plane were deduced. In all cases the twinning plane was found to be (111); lateral boundaries, however, were found which were (112) such as the one indicated in Fig. 1. Therefore, as in the case of diamond1 and germanium' only (111) twinning occurs in silicon. We wish to thank Mr. Hino for the use of the ingot as well as for its metallographic preparation. References 1C. B. Slawson: American Mineralogist (1950) 35, p. 193. 2 W. C. Ellis and R. C. Treuting: Trans. AIME (1951) 191, p. 53; Journal of Metals (January 1951). 3W. C. Ellis: Trans. AIME (1950) 188, p. 886; Journal of Metals (June 1950).

Jan 1, 1953

By Gary P. Thomason

INTRODUCTION One may have heard about how various projects were financed or certain companies were successful in obtaining a bank loan, but there are many more projects and companies who fail to get the money they need. At least a portion of these failures, and a large percentage of the frustrations connected with even the successful financings, are a result of not understanding the process of obtaining money. Recent years have seen a proliferation of debt financing sources available to finance minerals operations (see the next Chapter 11), but these represent only a minor portion of the minerals financing market. The fundamental source of borrowed money to many minerals related companies remains the banks. Therefore, understanding the "Loan Approval Process" can easily mean the difference between getting the money or not. LOAN APPROVAL PROCESS The initial stages of the loan approval process should begin long before the bankers, and the organizations they represent, enter upon the scene. The loan approval can be broken down into six stages: 1) Generation 2) Preparation 3) Presentation 4) Evaluation 5) Approval 6) Documentation As you can see in Figure 1, the bank is only directly involved in the second half of the process. The perils in obtaining financing for the smaller minerals venture are primarily in the first three stages, not the last three. The minerals venture making application for a loan can, in almost every case, improve its chances of success by carefully planning and preparing itself and the information that will be required of it in the loan approval process. Generation This first step in the process is deciding on the need for a loan. (Earlier papers in this Book and in Chapter 11 provide some guidance.) It is surprising how many ventures confuse the need for money with the need for a loan. Suffice to say that the equity investor risks both the timing of the yield on his capital and, ultimately, his capital. The lender, on the other hand, advances temporary funds which he expects to be repaid on a specific schedule with a fixed

Jan 1, 1985

By E. H. Miller, E. J. Hall, M. J. Flak

It is well known that, with the exception of the so-called " niter-and-nails " method, all methods used for the fire-assay of salphide-ores,* especially those of iron, zinc, lead and copper, are very tedious and require the constant attention of the assayer. The objections to the niter-and-nails method are: The liability of the charge to boil over, due to the presence of the' niter; the low results in silver (uncorrected); and the frequently large discrepancy between the actual weight of the lead button and the calculated weight. In many cases the buttons are too small to collect all of the gold and silver contained in the sample, while in others they are too large for cupellation. It was thought that, if these objections to the niter method could be eliminated, it mould give a method for the crucible-assay of sulphide-ores, and especially the low-grade ores of zinc and copper, which would be superior to any method in use at the present time. The only similar methods of assay are those of Perkins,t Rhead and Sexton,$ and Mitchell. The method of Perkins requires too much litharge for it to be a commercial success; that of Rhead and Sexton, utilizing the prelimiilary assay we found to be the best;—the charge for the final assay, however, was modified by having borax-glass added to it; also, the oxidizing power of the niter mas determined by a charge which difters from either the preliminary or the

Jan 1, 1904