Search Documents

By Svend Rordam

THE development of a cement that will resist the destructive action of sea water and other corrosive waters is a problem that has occupied cement chemists for the past one hundred years. It has been found that of the various salts that commonly occur in corrosive waters, sodium sulphate, magnesium sulphate and magnesium chloride are most destruc-tive to cement. Many investigations have been carried out in the United States, in Canada, and in Europe to solve the problem of what constitutes a sulphate-resistant cement, and during the past 10 years some of the findings give definite information in this respect. COMPOSITION OF CEMENT Portland cement is composed of four major compounds: 1. Tricalcium silicate 3CaO.Si02 (C3S) 2. Dicalcium silicate 2CaO.Si02 (C2S) 3. Tricalcium aluminate 3CaO.Al203 (C3A) 4. Tetracalcium aluminoferrite 4CaO.Al203.Fe203 (C4AF) The two calcium silicates are the main contributors of strength. The tricalcium aluminate contributes some to the early strength of the cement but has the least resistance of the four compounds toward the attack of sulphate waters. The tetracalcium aluminoferrite does not contribute very much to the strength, but is far more resistant to sulphate waters than the tricalcium aluminate. When hardened cement is exposed to water containing sodium or magnesium sulphates, these salts will react with the hydrated tricalcium aluminate in the cement and form compounds that will cause a swelling, disruption and crumbling of the hardened cement.

Jan 1, 1939

By Milton E. Wadsworth, J. Brent Hiskey

Galvanic interaction between particulate chalcopyrite (CuFeS2) and copper results in the rapid conversion of chalcopyrite to chalcocite. The effects of temperature, surface area, concentration of sulfuric acid and agitation were systematically evaluated. The kinetics were found to be controlled by a steady-state current flow controlled by the effective anodic and cathodic surface areas involved in the galvanic couple. The experimental activation energy was 11.5 and stoichiometric data and reaction products have been characterized. The overall kinetic system has been evaluated based upon an electrochemical model.

Jan 1, 1974

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

Each spring most secondary schools select their best student science exhibits, prepared during the preceding academic year, and send them to regional "Science Fairs", which now number over 220. Winner-finalists of these regional contests are then sent to the annual National Science Fair, conducted by Science Service, a non- profit institution for the popularization of science, for final judging. (The Fair is now known as the "National Science Fair-International" because of participation by finalists from Japan, Thailand, Germany, France, Sweden and Canada.) For the first time since the Fair was started in 1950, AIME participated in the awards presentation. Held this year in Baltimore, Md., from May 5 to 9, five members of AIME's Washington, D.C., Section consented to represent the Institute as judges. They were: Marlin J. Ankeny-Director, Bureau of Mines, U.S. Department of the Interior. Kenneth N. Weaver-Director, Maryland Department of Geology, Mines, and Water Resources. William Harper-American Petroleum Institute. Vice-Chairman, Washington Section, AIME.

Jan 7, 1964

For a nation whose mining industry has generally been floating through history in the shadows of major mining developments elsewhere in the world, Australia has in the decade of the Sixties made a convincing bid to be one of the world's great "store- houses" of minerals. In fact, at the rate things are developing Down Under and Out Back, what with professional prospecting teams crisscrossing the continent under the direction of professional exploration management, Australia may one day find itself as the world's greatest storehouse. Whereas Necessity may be the Mother of Invention, Consumption is surely the Mother of Exploration. At least this is true in Australia of today. First, the forecasted shortage of iron ore in the world led to the fabulous discoveries in the Pilbara district of Western Australia. Now, the demand for nickel has generated even more interest among mining companies in the vast, untapped potential of Australia.

Jan 10, 1968

The Industrial Minerals Div., of the AIME meeting scheduled for Nova Scotia Sept. 8-12, 1953, promises to be one of the outstanding gatherings ever attended by the group. Complementing the educational value of technical sessions will be the superb fishing, boating, golfing, and tennis facilities. [ ] Sponsor of the meeting is the Nova Scotia Mining Society. The Canadian Institute of Mining and Metallurgy and Industrial Minerals Div., AIME have been invited to participate. The land immortalized by Longfellow's poem, Evangeline, still contains much of the forest primeval-enough to make it a wonderful vacation spot for delegates and their families. Its scenic beauty is almost unmatched in the area north of the border. Quoting from the Nova Scotia tour book; "Nova Scotia, once known as Acadia, is 374 miles long, from 600 to 100 miles wide ... Excepting the Isthmus of Chignecto, 17.5 miles wide, the province is entirely surrounded by water, no portion being more than 50 miles from the sea . . . has 4625 miles of coastline, guarded by 356 lighthouses and fog alarms. The province is renowned for its picturesque coastline, its harbors dotted with islands, its deep valleys and multitude of beautiful lakes." A progress report on the plans for the meeting will be made monthly. Thus far, technical sessions will be held at Keltic Lodge, Ingonish, N. S. The lodge will also be the starting point for many of the field trips and social events which are in various stages of planning and development.

Jan 1, 1952

By H. Engelmann

The very extensive development of a brown coal formation, in the region of the Rocky Mountains, is well known to all of yon. The existence of these coals was known years ago, but they were of no practical importance until within a few years, when the mineral wealth of that country began to be developed and railroads were built. As their qualities became better known, their adaptability to domestic manufacturing and metallurgical purposes was more appreciated. They are still much undervalued, although they are mined at some points on a very extensive scale. A large portion of this coal formation is of cretaceous age, while it appears to extend into the tertiary epoch; but whatever difference there may be in the ages of these coals of different localities, they all have some common characteristics which distinguish them from our Eastern stone coals of the

By Paul C. Merritt

For more than 100 years, British Columbia has been considered a mountainous mining province, rich with potential but relatively poor in actual production. Times have changed. Today, Japanese interests and money have altered the difficult, if not once impossible, economic conditions and market factors which until recently precluded any great growth of the British Columbia mineral industry. The mining boom now underway in British Columbia has carried the total value of mineral production in the Province to a record height in 1962 as it rang up a 27% increase over that of 1961. Breaking the $200 million barrier for the first time, total value of British Columbia's mineral output reached $229- 276,385. Of this amount, metals accounted for 70%; industrial minerals, 6 %; structural materials, 9 %; and fuels, 15%. The substantial increase is attributed to the record production of copper, iron, asbestos, natural gas and petroleum, in addition to the continuing high production rate and favorable prices of other mineral commodities.

Jan 12, 1963

Shovel To further increase the efficiency in the production of their foundry sand, the American Silica Sand Co. has purchased a new and improved shovel that will be used for loading trucks at their Reynolds Pit. The [ ] new shovel will greatly facilitate winter mining operations and make possible larger winter shipments of the company's foundry sand. The Reynolds Pit is one of three sand pits in the Ottawa district owned by American Silica which produce sand that is refined for foundry use. Circle No. 1 Electric Switches The Crane Electric Co. has just announced the production of their R-1000, a new rotating limit switch designed to control the travel of any rotating device requiring interruption or establishment of electrical current after a predetermined number of revolutions. It is useful for machinery, lifts, and other power equipment. The switch is presented in a finished case, 16 gage, reinforced, with walls of sufficient strength to hold the entire mechanism and all the parts in accurate alignment. The worm gear combination has a 60 to 1 ratio, sufficient for most industrial uses. The number of revolutions can still be increased by using various combinations of driving sprockets, either on the shaft of the switch, or on the sprocket of the unit controlled by the switch itself. Circle No. 2

Jan 1, 1952

PROF. Henry Louis, Newcastle-on-Tyne, England (communication to the Secretary): I have read this paper with much pleasure. It presents a very accurate summary of a very interesting district. Like the authors, I was struck by the extreme General View, near French Co.'s Cyanide Works, Showing Horse-Whims, etc. flatness of this region, which looks strange to a gold-miner accustomed to other reef-districts. This prevailing absence_of relief in the contours is shown in Figs. 1 to 4, from photographs taken in August, 1897, some of which also show the horse-whims used here for hoisting. The flatness of contour is due, no doubt, to the fact that the rocks are similar in structure over large areas and are easily decomposed. I am quite at one with the authors in looking upon the so-called " placers " as the result of decom-

Jan 1, 1899

By Z. M. Zavodni

The stability of waste dumps depends to a great extent on the physical properties of the underlying foundation. These physical properties are evaluated through surface geotechnical surveys, subsurface exploration, and field and laboratory testing. Sufficient information must be obtained to define and assess the strength, consolidation, distribution, topographic and hydrogeologic properties for these materials. Important foundation data collected in the field include: surface infiltration rates, downhole hydraulic conductivities, ground water levels, bedrock structural parameters, soil types and soil thickness. Laboratory testing should identify the classification, strength, moisture content, hydraulic conductivity, attenuation and consolidation characteristics. Summarized in this paper are procedures and typical results of porphyry copper leach dump foundation investigations. Laboratory properties and design recommendations for potenia1 foundation liner materials are described. Back analysis and laboratory foundation strengths are compared. The topographic effect of the foundation on dump behavior is discussed and a foundation pore pressure monitoring experiment at the toe of an active waste dump is described.

Jan 1, 1985

By John A. Church

The Lake Superior blast-furnaces probably represent the maximum economy of fuel possible in this country. They smelt an ore which is very rich and easily reducible, and as the small amount of gangue present is not all silica, but in part a silicate, the amount of limestone required is a minimum. The average yield of the ore treated at six furnaces was 63 per cent., and the average quantity of limestone 179 pounds per ton of pig. The fuel used is charcoal, so burned as to retain most of the combustible volatile part, which, before the utilization of furnace-gas, was burned away. With these conditions it is not surprising that the Lake Superior charcoal practice is extraordinary in almost every respect. In any scientific discussion of American furnace work, the establishments there will be found at the head of the list, and they work under conditions which are extremely favorable for careful study. The Bay Furnace, near Marquette, has the honor of carrying "the broom" for the largest daily make. With a capacity of 1908 cubic feet it has, for months together, produced 29 tons of pig, graded at

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975

By Robert C. Edmiston

The measurement of temperatures in exploratory drill holes yields information on regional and local geothermal gradients and mean surface temperatures. This data may be beneficial to the mining geologist interested in the occurrence and oxidation of metallic sulfide minerals or to the mining engineer interested in subsurface temperatures or water movement. Additionally, the estimation of mean surface temperatures by the projection of thermal gradients to the ground surface provides data on which to evaluate infrared imagery as an exploration tool. Temperature measurements in 30 diamond drill holes in the Silver Bell mining district of Arizona show that a regional geothermal gradient of 2.45°C per 100 m increases to 3.03°C per 100 m near the ground surface. It is also found that an anomaly in the mean annual surface temperature of 0.5°C is associated with the shallow occurrence of disseminated sulfides. Changes in the geothermal gradient due to topography, water circulation, and formation changes also occur.

Jan 1, 1976

By O. Bergmann, R. E. Lueders, R. R. Ellefson, H. M. Brennecke, D. S. Davies

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105OC. Iron is removed from the pregnant liquor as a jarosite, and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as So, jarosite, and gypsum. The process is highly versatile and can recover precious metals, molybdenum, and zinc when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1982

By George J. Simchuk

Selection of an applicable stripping method and the subsequent determination of appropriate sizes of selected equipment are discussed. The case in point is Utah International, Inc.'s Goonyella mine located in central Queensland, Australia. A detailed study of the various types of stripping methods now practiced throughout the world led to the conclusion that large draglines would be the logical choice for Goonyella. The optimal size of dragline was then determined by first designing a series of cut diagrams using an array of machine and pit geometries followed by a cost comparison of the various sizes of machines, in terms of their effective spoil radius. A dragline with a 51-cu-yd bucket was determined to be of optimum size. Further calculations, incorporating total overburden moved from both the highwall and spoil sides, required that four drag lines, two equipped with 40-cy-yd buckets and two with 54-cu-yd buckets, be used to satisfy the stripping requirements at Goonyella.

Jan 1, 1973

By Donald E. Scheck, Da-Rong Chou

The application of geostatistics to coal reserve analysis is discussed. One problem in particular, the selection of the optimum locations for exploratory drill holes, is considered in detail. A new interactive program to help the geologist determine the best locations is described and applied to a specific property. The steps in the process are described and then illustrated using a mine's actual data. First, a variogram is selected based on graphical displayed information from the known sample data. Kriging estimates are made for the region of interest and the blocks within the region. The location of future exploratory drill holes is selected based on the criterion of minimizing the region estimation variance for a given number of exploratory holes. The least number of exploratory holes required to meet a specified upper limit on the regional variance is also determined. The computer generated recommendations for the exploratory drill holes are compared to a manually prepared drilling plan. The post- drilling analysis of the results is compared to the predicted values.

Jan 1, 1983

H. H. Kellogg (Columbia University)—The accurate measurements of the equilibrium gas ratios for the reaction: Pb(1) + H2S = PbS(c) + H2 [I] reported in this paper are a distinct contribution to the literature, and the authors are to be congratulated. I wish to comment, however, on the correlation of the data which is presented. The authors show a straight line correlation of log H2S/H2 vs 1/T, Fig. 1, and are satisfied with this for calculation of ?Fo even when extrapolated to low temperature (427 °C). Heat capacity data for the constituents of this reaction are available (at least to 900°K), however, and ACP for reaction [I] is finite and positive in the temperature range studied. Simplification of the heat capacity equations yields: ?CP= 2.71 + 1.65 x 10-3T (298°-900°K) This positive value of ?CP should result in a small but noticeable curvature of a plot of log K vs 1/T. That the experimental data fail to show such a curvature may be traced to another oversimplification of the author's treatment of their data. They assume that the activity of liquid lead is unity for all temperatures, so that

Jan 1, 1961

By Moshe Sheinkin, Burke O. Trafton

This paper describes the use of a computer in analyzing the expected return on a mining venture. The computer program is designed to incorporate all aspects of a mining project, including the mine, mill, smelter, and refinery. Data input may consist of the operating variables in each phase such as the mining rate, grades, reserves at the mine, and the technical operating characteristics of the mine, mill, smelter, and refinery. Detailed tax computations are shown for a domestic operating company, for a foreign company and for a foreign subsidiary. In addition, the use of the various options that are available such as expense write-offs or deferments to create tax credits during preproduction years are considered, and its effect on the DCF. The program is also constructed to accommodate changes in metal prices, and escalation of capital requirements and operating costs. Output consists of profit and loss statements for entire projects using different methods of depreciation, cash flows, discounted cash flows, net present value and returns on investment. Returns on investment are computed for equity investment, total investment, and total investment less tax credits. Allowances are made for bank and guaranteed loans. Additional financial statements can be made for the following: a) A mine-mill segment with a concentrate selling schedule b) A mine-mill-smelter complex with a smelter product selling schedule c) Profitability of the smelter separately d) Profitability of the refinery separately

Jan 1, 1969

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928