Search Documents

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By Luis N. Henriquez

One form of encouragement for the small copper mining sector in Chile has been the construction and management of custom mill facilities to process the ore. The paper describes an economic analysis framework for the evaluation of government custom milling opportunities. Feasible mill locations and capacities within a region are selected and the infrastructure and milling costs associated with each combination of location and capacity are assessed. For each combination, the economics of developing and operating known copper deposits in the region is evaluated, and an optimum cut-off grade and mine capacity is selected for the deposits which justify development. Since the total ore supply from mines in the region may exceed a particular custom mill capacity, mine development is scheduled to optimize the economics of the mill facility. Finally, the best custom mill location and capacity is selected on the basis of overall costs and benefits. A copper mining region in northern Chile is used to illustrate the application of the model. A mobile mill approach is examined and compared with the fixed location mill alternatives. Results are analyzed as a function of copper price.

Jan 1, 1977

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).&apos; The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f&apos;racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,&apos; have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961

By N. R. MacMillan

INTRODUCTION The Bullmoose Coal Project is part of a major development in northeastern British Columbia which comprises a new rail line, a new townsite, powerline, highway, the upgrading of the Canadian National Railway&apos;s main line, a new coal port at Prince Rupert and two new coal mines, the Bullmoose mine and the Quintette mine. The total investment by all parties is estimated to be in excess of $2.6 billion and made up approximately as follows : [Table No. 1 $ Millions - Quintette Coal Limited 950 Teck-Bullmoose Coal Inc. 275 Canadian National Railway Company 800 6 British Columbia Railway Company Port at Prince Rupert 280 Townsite, Roads 6- Power ] The new infrastructure is intended to serve not only the Bullmoose and Quintette coal projects but also eventually a number of other coal properties in northeastern British Columbia. The Bullmoose project is structured on a joint venture basis as follows : [Table No. 2 Teck Corporation 51% Lornex Mining Corporation Ltd. 39% Nissho Iwai Coal Development 1 0% (Canada) Ltd. -- 100% ] The mine has a capacity of 2.3 million tonnes of clean coal per year. In the initial years 1.7 million tonnes will be metallurgical coal and 0.6 million tonnes thermal coal. After the first three years of operations the annual production of metallurgical coal will increase to an average of approximately 2.1 million tonnes and the production of thermal coal will decrease to an average of approximately 0.2 million tonnes. At this level of 2.3 million tonnes annual production, the Bullmoose mine has sufficient reserves for at least 26 years of production. History Brameda Resources Ltd. commenced coal exploration in the Bullmoose-Sukunka area in 1969. Teck obtained an option on the Bullmoose coal licences in 1970 and started surface exploration and diamond drilling in 1971. Teck earned a 50% interest in the property, and thereafter expenses were jointly financed by Teck and Brameda. In 1981 Brameda merged with Teck making Teck the sole owner. The initial phase of the exploration program, which was completed in 1975, included 7,200 meters of diamond drilling in 35 holes. During 1976 and 1977, detailed exploration and test work were carried out on the South Fork and West Fork areas where multiple seams close to surfaces indicated the potential for large tonnages of strippable coal. In those two years, work included road construction, detailed mapping and trenching to outline the coal seam traces at the surface, 6,300 meters of diamond drilling in 80 holes, and 300 meters of underground bulk sampling from seven adits. Washability tests and analysis work were carried out on the drill cores and adit samples, and pilot plant washability studies were undertaken. In 1978 and 1979 Teck engineers prepared open pit mining plans and production schedules and Kaiser Engineering was retained to prepare a layout of the plant preparation facility. A feasibility study prepared by Teck&apos;s engineering group in January 1982 was the base document used by the Lenders in assessing the technical and economic viability of the project. Property Location The property lies some 650 kilometers northeast of Vancouver, and 87 kilometers south by road from the village of Chetwynd. The Sukunka property (British Petroleum) adjoins to the north, the Mount Spieker property (Ranger Oil Option) adjoins to the east, and the Quintette property is located to the southeast.

Jan 1, 1985

By MARIUS R. CIMPBELL, Edward W. Parker

DESCRIPTION. ACCORDING to the estimates prepared by the U. S. Geological Survey, the area underlain by workable coal-beds in the United States is 496,776 sq. miles. Of this total area, 480 sq. miles contain the entire anthracite coal-fields of Pennsylvania. The bituminous coal-fields are estimated to be contained in areas aggregating 250,051 sq. miles. The grade of coal between bituminous and lignite, and which is designated by the Geological Survey as " sub-bituminous," is estimated to be contained within areas aggregating 97,636 sq. miles, while the areas containing lignite aggregate 148,609 sq. miles. The coal-fields are divided, for the sake of convenience in classification, into six main provinces, as follows: 1. The Eastern. Province, containing the anthracite coal-fields of Pennsylvania and the bituminous coal-fields of the Appalachian region-namely, those of western Pennsylvania, Ohio, Virginia, West Virginia, Kentucky, Tennessee, Georgia, Alabama, and small outlying areas in North Carolina. 2. The Interior .Province, containing the bituminous coal-producing regions of Michigan, Illinois, Indiana, western Kentucky, Iowa, Kansas, Missouri, Oklahoma, Arkansas, and Texas. 3. The Gulf Province, containing the lignite-areas of Alabama, Mississippi, Louisiana, Arkansas, and Texas. 4. The Northern or Great Plains Province, containing the lignite and sub-bituminous areas of North and South Dakota, eastern Montana, and northeastern Wyoming. 5. The Rocky Mountain Province, containing the bituminous and sub-bituminous areas of western Montana and western Wyoming, Colorado, Utah, and New Mexico. 6. The Pacific Coast Province, containing-the areas of Washington, Oregon, and California.

Apr 1, 1909

Jan 1, 1910

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson&apos;s high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes&apos; iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By Heinrich Oscar Hofman

IN THE death of Professor Hofman who was born on Aug. 13, 1852 and died on April 28, 1924, the world has lost a great metallurgist and a great author of metallurgical literature. Measured in time his life was not quite seventy-two years, but measured in work accomplished it was much longer than this. It is not surprising that Dr. Hofman became a great scholar for his father, Karl Hofman, was on the faculty of Heidelberg University, and his early days were spent in these surroundings. He studied in the University under such men as Kirchoff and Bunsen and often spoke of the intimate relations he had with them. Following his course at Heidelberg, he studied at the Clausthal Mining Academy where he graduated with honors, receiving the degrees of Mining Engineer and Metallurgical Engineer in 1877.

Jan 1, 1924

By Walter Crooke

Regenerative hot-blast stoves are now in general use in all parts of the world, and are so well understood and appreciated, that I need not take up your time with an account of their history and introduction into the United States. My object in writing this paper is to give you a short description of a stove that is now being very favorably received and adopted here (see drawing). The stove was first introduced into this country in 1887 by M&apos;Clure & Shuler (now M&apos;Clure & Amsler), who have the management of the patent right in the United States. The English design had to be modified to suit the exigencies of American blast-furnace practice, which, in many respects, widely differs from our English experience. In the first place, the fire-bricks used in America expand to an extent unknown in England, and it became necessary to make special provision for this by increasing the number of cross-walls, and by leaving a space at the top of the stove through which the lining could expand. The expansion laterally was, however, more difficult to provide for, as the combustion-chamber in the center, being the hottest part of the stove, must necessarily expand more than the outer walls, and therefore tend to squeeze up the flue-openings. On first introducing these stoves to American ironmasters, a feel ing seemed to prevail that a " four-pass " stove did not utilize the whole of its surface. They also had an idea that the " two-pass " stove let the burning gas go before all the duty had been extracted from it; so that it was found neceseary to design a stove of a special character to suit their wishes. Hence the "three-pass" chimney top stove now before your notice, the advantage claimed for which is that each stove is independent, requiring no underground chimney flue or stack, and can be erected at a very light cost. The working of these stoves has proved to be very successful wherever they have been introduced.

Jan 1, 1891

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series&apos; has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By W. A. Clark

The production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl. of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. Reasons fob Gravel Packing Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b) allowing deep submergence of the pump into the oil zone. In a conventional well—that is, where the liner is set in an open hole-. even though perforation sizes are chosen according to known rules based on analysis of sand grains from samples from the zone, there is likely to be some production of sand. This may be due to the miscalculation of

Jan 1, 1940

By W. A. Clark

The production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl. of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. Reasons fob Gravel Packing Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b) allowing deep submergence of the pump into the oil zone. In a conventional well—that is, where the liner is set in an open hole-. even though perforation sizes are chosen according to known rules based on analysis of sand grains from samples from the zone, there is likely to be some production of sand. This may be due to the miscalculation of

Jan 1, 1940

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig&apos; 1. I&apos; In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig&apos; 1. I&apos; In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By P. D. Merica

MY remarks are addressed to the question whether a program of international mineral control can effectively serve as a means of maintaining world peace in the kind of world envisaged by the Atlantic Charter. They do not touch the quite different questions whether such control could be appropriately used for postwar punishment of Germany and Japan, or for other purposes. I assume also that the question relates, not to the transition period immediately following the war, but to the more normal years which we hope will succeed this. Finally, they deal primarily with metals and metallic minerals rather than with. oil or coal or other minerals, although they may be applicable also to these other nonmetallic materials.

Jan 1, 1944