Search Documents

By A. Faber du Faur

At the request of some of the members to whom I have shown a collection of specimens of sulphur from southern Utah, I herewith present some notes relating to the mines and the method of extracting the sulphur from the ore. In preparing these notes I have borrowed from a paper by Prof. G. vom Rath, published in the Neue Jahrbuch fur Mineralogie, vol. i., 1884, dated Salt Lake City, December, 1883. The Cove Creek sulphur-bed, now worked by the Dickert & Myers Sulphur Co., is in Beaver county, near the line of Millard county. It was first discovered by Mr. Ferdinand Dickert in 1869 ; other beds in the same neighborhood mere found by him from 1872 to 1875, making altogether 22 mining claims. The want of railroad communication prevented the early development of these claims; but in 1883 Mr. F. Dickert put up a plant for extracting sulphur from the ore, which proved a perfect success; and in 1885 the property was transferred to a stock company organized under the laws of Utah. The railroad station nearest to the Cove Creek mines is Black Rock, on the Utah Central Railroad, 204 miles south from Salt Lake City, and about 26 miles west of the mines. The road from Black Rock to the mines passes through desert and lava-bed, to the road leading from Kanosh to Beaver, which latter road it joins near Cove Creek fort, a square stone enclosure, erected by the Mormons for protection against the Indians. Cove Creek fort is situated near the eastern limit of a plain bounded on the west at a distance of about 12 miles by the Mineral range, and on the east by the Sulphur mountains, forming part of the Tushar mountains. To the northwest the plain runs into the Sandy desert. About 3 miles from the fort rises a solitary hill about 1000 feet above the

Jan 1, 1888

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Staff

Concentrates at the rate of 1000 tons a day are being smelted by International Nickel Co.&apos;s new commercial flash smelting furnace. Developed by Inco, the process is a radical departure from the former practice which involved conventional smelting in coal-fired reverberatory furnaces. In the new process copper flotation concentrate and flux are injected horizontally with oxygen into a specially designed reverberatory furnace, and smelting temperature is maintained solely by the flash combustion of iron and sulphur while the particles are in suspension. The major benefits of this new process stem from two sources: 1)-Substitution of energy from local resources for imported coal; and 2)-Production of liquid sulphur dioxide, replacing equivalent imported sulphur. A measure of these benefits is afforded by considering the saving, in 1954, of 60,000 tons of coal and the production of 70,000 tons of liquid sulphur dioxide, equivalent to 35,000 tons of sulphur.

Jun 1, 1955

Low metal prices prevailing at the beginning of 1950 stimulated the search for improved mining methods. More experience was gained during the year with such new developments as the jackleg drill, millisecond delays as applied underground, trackless mining, and Diesel powered equipment. One of the outstanding innovations in mining practice was the starting of the Round Mountain "dry land gold dredging operation." The Government is now inviting the mining industry to open up every available source of new metal supply and this circumstance will undoubtedly speed the development of new machines. New methods will also result but it is doubtful if economic efficiency will be at its peak.

Jan 2, 1951

By E. N. Cameron

Graphite has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey. The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs.

Oct 1, 1956

By A. E. Nehrenberg

IN an earlier publication&apos; it was shown that the.. shape assumed by a volume of growing austenite is inherited from the prior structure. The matrix grains of pearlitic microstructures are equiaxed, and austenite grows in an equiaxed manner in these prior structures. Martensite and bainite, on the other hand, have an acicular grain structure, and the austenite produced in such structures grows in an acicular manner. In the discussion of this paper&apos; it was pointed out that in cold-rolled tempered martensite, austenite grows in an equiaxed, rather than an acicular manner. The results of an experiment carried out to arrive at an understanding of this behavior are illustrated by the micrographs. Fig. 1 shows the acicular microstructure produced by heating tempered martensite to a temperature within the Ac1-Ac3 range, 1350°F. When tempered martensite is cold rolled, then heated to the same temperature, the equiaxed structure shown in Fig. 2 is produced. A sample of cold-rolled tempered martensite heated at 1350°F just long enough for the formation of a small amount of austenite is shown by Fig. 3 to have an equiaxed (recrystallized) ferrite grain structure. The small particles of. austenite which formed at 1350°F in the equiaxed ferrite matrix are likewise equiaxed. Thus, the equiaxed growth of austenite in cold-worked tempered martensite is not a contradiction of the principles described in the previous paper, for the growth pattern reflects the matrix grain structure existing at the time of austenite formation. References A. E. Nehrenberg: The Growth of Austenite as Related to Prior structure. Trans. AIME (1950) 188, pp. 162-174; Journal of Metals (January 1950). 2 J. R. Vilella and R. A. Grange: Discussion of ref. 1. Trans. AIME (1950) 188, pp. 1378-1381; Journal of Metals (November 1950).

Jan 1, 1953

By Gordon M. Matheson, Charles V. Logie

The current state-of-the-art design of mine pillars can be grouped into empirical and numerical design techniques. Numerical design techniques are based on sophisticated computational techniques which analyze the stresses and strains through the interstices of a pillar. Empirical techniques are less exact, but have been widely used, particularly for coal mine pillar design, because of their ease of computation. Over the years numerous empirical equations have been proposed to calculate the ultimate strength of coal mine pillars. This paper presents a review of the various equations which are most frequently utilized and examines the fundamental assumptions, limitations and applicability of the design formulae. The review intends to provide the practicing mining engineer with an understanding of the assumptions and mathematical basis of each equation to aid in the selection of the criteria most applicable to his specific design problems. Recommendations are made of the empirical equations that are presently most acceptable for design.

Jan 1, 1983

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

By Ernest F. Burchard

In connection with the work of testing structural materials for the use of the U. S. government at the laboratories of the technologic branch of the U. S. Geological Survey at St. Louis, Mo., from September, 1904, to April, 1909, and since then at Pittsburg, Pa., large quantities of sand, gravel, and crushed stone have been needed from time to time, besides samples of building-stone, clays, and other quarry-products. In many instances it has been necessary to obtain single samples of sand, gravel, or crushed stone in lots of a car-load or more. For obvious reasons all these collections have had to be made by a representative of the Survey. As the work progressed it was found essential that numerous geologic data should be gathered regarding the materials collected, in order that they might be properly classified as to kind of material, source, geologic age, etc., and that they might be rated according to quantity available, accessibility to transportation facilities, approximate costs, suitability for special purposes, etc., and that notes might be taken regarding undeveloped deposits of possible value. Furthermore, it mas desired that the selection of materials for tests should be made broadly, so as to cover, first, the representative types of material, and later, if possible, the typical materials of the more important building-centers in the United States. In order to insure a certain degree of uniformity in this work and economy of effort and expense, it was decided that as much of the sampling as was practicable should be done by a member of the geologic branch, whose regular field-trips could be combined conveniently with those necessary for procuring materials for the laboratory. During parts of the last three years 1 have been engaged in field-work of this sort.

Jan 1, 1911

By D. J. Coolidge, H. L. Sheakley

This paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is cornrnonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. I). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers&apos; log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. Properties of the St. Peter Sand From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1948

BENEFICIATION AND CONCEN&apos;TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

By Richard P. Sheldon

In the last several decades, techniques of data collection have been rapidly evolving. Automated spectroscopic techniques in the chemical analysis of rocks for example have advanced to the point that we can analyze samples faster than we can grind them. Remote sensors of LANDSAT give us intensity measurements in four color bands of every acre of the U.S. every 19 days. Common depth point seismic instrumentation systems used at sea for surveying and networks of seismometers arrayed around the country for earthquake studies likewise are generating vast amounts of data. These along with many other earth science data generating systems have caused a veritable data explosion. How do we deal with these enormous amounts of geologic data presently being produced as well as those produced in the past, and to be produced in the future? There is an immediate need to acquire and utilize past and present basic data in order to address today&apos;s national earth science problems. Also data being collected and stored now must be compatible with future data in order for us to be able to undertake the wide spectrum of analysis that must be made in the future. This is a big order! In order to organize and to be able to analyze these data, the USGS has embarked on a wide ranging program of compatible data base construction and the development of computer technology, based on interactive computing, to facilitate resource assessments and analyses. These activities are analogous to two sides of a coin. One side deals with the logic, philosophy, and mechanics of information storage and retrieval; and the other side deals with the sensible application of computer technology to the treatment of data. These

Jan 1, 1977

By E. J. Fasiska, L. Zwell

PREVIOUS investigations 1,2 of Fe3P described by pearson3 and schubert4 show that Fe3P has a bct unit cell having four Fe3P tetrahedra centered around each lattice point. The space group is 14, No. 82, and all atoms occupy general positions 8(g). The cell dimensions3 are: a = 9.090, c = 4.446 kX, with an axial ratio of c/o = 0.4891. We have measured the lattice parameters of Fe3P, using a Fe as an internal temperature standard, at 23°, 414°, and 678°C and computed the thermal expansion over this temperature range. The Fe,P was prepared by melting under vacuum (after flushing with argon) a commercially pure iron and "ferrophosphor" in a high-frequency induction furnace. Part of the ingot was crushed for X-ray examination and for chemical analysis. X-ray diffraction and light microscopy indicated iron phosphide (Fe3P) present as the major constituent and a small amount (about 5 pct) of a Fe. Chemical analysis showed 0.05 wt pct Si, 0.008 wt pct N, 0.018 wt pet C, and less than 0.02 wt pct each of other metallic elements. X-ray diffraction powder patterns were obtained from a mixture of iron and Fe3P sealed in an evacuated quartz capsule using a Unicam high-temperature

Jan 1, 1968

By G. W. Hodges

The Basic Oxygen Process shop at Gary Works is a three vessel shop tapping 220 ton heats. The larger portion of the heats are teemed into ingot molds with the remaining heats being continuously cast in a single strand continuous slab caster. Ingot production includes a wide range of carbon, alloy, and high-strength steels in many ingot sizes for bar, structural, plate and sheet and tin products. Individual ingot weights vary with the number of ingots per heat ranging from a high of 48 to a low of five. Caster production is primarily Riband, a proprietary low carbon grade for sheet and tin applications developed by United States Steel for continuous casting; some Riband steel is vacuum degassed prior to casting. Maintaining a satisfactory level of ladle performance on both ingot and caster heats with a high production rate and widely varied product mix is a demanding and exacting job requiring the best of equipment, materials, and, most importantly, personnel. The improving trend in ladle performance in the No. 1 BOP shop at Gary is due to a combination of factors, which will be described in the following presentation.

Jan 1, 1972

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By W. P. Lass

(San Francisco Meeting, September, 1015) THE gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co.; Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About. 3 or 4 tons of this precipitate are produced monthly having a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the by-products from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 lb. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This&apos; practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high.

Jan 7, 1915

By B. B. Zavoico

Considerable progress has been made during the past year throughout the Russian petroleum industry. Perhaps the most remarkable achievement is the execution of the programs set out by the Central Planning Bureau of the Department of Commerce. These programs have been increased twice during the past operating year, necessitating drilling the richest reserves, instead of developing gradually as originally planned. The fulfillment of the set-out programs during the past few years makes therefore the present five-year plan of considerable importance to the international oil statisticians in approximating actual supply conditions up till 1933. The production of all Russian fields increased by 14,200,000 bbl. as compared with the 1927-1928 operating year, while the next year&apos;s program anticipates a further increase of 15,700,000 barrels. It appears therefore that production for 1932-33 will total 187,000,000 bbl., or approximately double that of the operating year just closed. It is also evident that the old fields are counted upon to produce only about 67 per cent. of the total, the new fields, not yet discovered, to furnish the balance of 33 per cent. The Soviet oil leaders therefore are hoping to have new fields discovered and developed by 1932-33. However, as in the past wildcatting

Jan 1, 1930

By J. A. Fulton

GOLD was discovered in the Sierra Nevada by J. W. Marshall on Jan. 2, 1848. The town: of Grass Valley soon sprang up and contained several stores in 1849; but the population of the town has always reflected the fluctuations in quartz mining. Gold-bearing quartz was found on Gold Hill in September 1850, and in the next two years most of the quartz bearing veins in the vicinity were located. At first, the quartz was crushed in mortars with spring poles; the Huff Co. took out $20,000 in this manner during the winter and spring of 1851. The first mill was put up in January, 1851. In 1866, there .were in Grass Valley 248 stamps, crushing 71,420 tons of ore with an average yield of $30 to $35; in Nevada City, there were 142 stamps, crushing 14,200, tons, with an average value of $25. But in 1918, only two properties in. this region, the Empire and the North Star, were producing. Since then, there has. been a revival of mining in the district and the following properties are being opened up: The Golden Center, Grass Valley Gold. Mines CO , Idaho-Maryland Mines Co., while the Sultana is kept unwatered and work is going on in a half dozen small properties.

Jan 2, 1926

By Brij M. Moudgil

Disposal of fine coal refuse is one of the major technical problems which could adversely affect growth and development of the coal industry. At present one of the most: common methods for disposal of fine coal refuse slurry involves impounding the slurry behind dams. However meeting new federal and state government regulations for building, maintaining and reclaiming these impoundments in addition to terrain and space considerations render this technique to be only marginally competitive with other disposal methods. The coal industry has been actively engaged in developing alternate disposal techniques which are economically feasible and environmentally acceptable. A review of coal refuse disposal problem and current refuse disposal practice both in the eastern and western coal fields is presented. Various promising techniques being developed for economical and safe disposal of fine coal refuse slurry are also discussed.

Jan 1, 1980

By P. H. Royster

On the Continent, ferromanganese has been produced in the blast furnace almost continuously since 1876, but little definite information concerning the practice is to be found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country, prior to 1904, but one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public..In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations; so the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Operating data were collected by the Bureau from eleven ferromangahese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P; the dimensions of seven of the furnaces are given in Table 1. The companies from whom this information was obtained, and to whom should go the credit for whatever value this information may possess, are the Bethlehem Steel CO.,

Jan 1, 1920