Search Documents

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man's dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives: 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1964

By A. Ross Rornmel

ABILITY to speak effectively is one of man's most longed for and coveted abilities. It is the ability to stand on one's feet, transfer knowledge and thoughts to others, to reach an objective professionally or otherwise by leading groups through a channel of planned thought. Each day group speaking plays an important part in making or marring success, and the engineering profession often provides this opportunity and requirement. An ability to speak effectively develops courage, poise, confidence, and prestige for the speaker. The technical man cannot be reluctant to face an audience. He is often called upon to do this in presence of employees, supervisors, and other groups. His ability to speak effectively is as much a requirement as the fundamentals of his profession. The three fundamentals of effective speaking are: (1) Enthusiasm and Confidence. These are joined because of their close relation. (2) Preparation. This includes knowledge of the subject. (3) Presentation. By this is meant the features of delivery.

Jan 1, 1946

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By J. F. Wolff

J. G. WOLFF, Duluth, Minn. (communication to the Secretary*).-In raising the question (" Newly Discovered Fossil Remains in the Cretaceous Shale," p. 1784) as to the possibility of the so-called Cretaceous remnants found on top of Mesabi Range orebodies really being Jurassic, the writer was acting under a wrong impression. In speaking of the matter with different geologists of note who have visited Northern Minnesota during the past year, lie understood one of them to refer to Jurassic shales existing quite extensively in Northwestern Minnesota. This apparently was entirely a misunderstanding. In answer to an inquiry in regard to this matter, Prof. W. H. Twenhofel, paleontologist at the University of Wisconsin, said that the known Jurassic nearest to Northern Minnesota is in Western Dakota. From the reproductions of fossils shown on p. 1785, Prof. Twenhofel tentatively correlated them as "middle-upper Cretaceous."

Jan 2, 1917

THREE regional meetings are planned for this summer and fall following the spring meeting held under the auspices of the Iron and Steel Committee and the Ohio Section at Cleveland in April and in lieu of a general fall meeting of the Institute. Plans for all of them are maturing rapidly. Excellent programs and. interesting visits to points of local tech¬nical interest are already assured. THE SALT LAKE CITY MEETING This meeting will be under the auspices of the Milling Committee and the Utah Section. It will be one of the features of the joint convention held the week of August 22 to 26 with the Western Division of the American Mining Congress. The Congress will be responsible for the general arrangements and for the program on the first day. The following general committees have been appointed:

Jan 7, 1927

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918 A preliminary program, for the New York Meeting was printed in the January Bulletin, and a more detailed program was mailed to all members early in January. The following schedule is the outcome, of sundry committee meetings up to the middle of January. Committee on Arrangements J.` E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman RALPH W. DEACON MRS. S. J. JENNINGS E. M. SHIPP J. V. N. DOER A. R. LEDOUX G. D. VAN ARSDALE L. `V. FRANCIS . . F. T. RUBIDGE ARTHUR L. WALKER Summarized Program MONDAY, FEBRUARY 18 9 a. m. to 5. p. m. Registration at Institute Headquarters. 10 a. m. Sessions on Coal and Non-Ferrous Metallurgy. 12.30 p. m. Luncheon at Engineering Societies'. Building. 2 p. m. Visit to Subway Workings.

Jan 2, 1918

Jan 1, 1924

Jan 1, 1924

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.' " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By George A. Morrison

THE Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Barberton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITE The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 250 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. GEOLOGY The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft, are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946