Search Documents

By T. Turner, C. L. Zimmerman, U. Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 km north of Atlanta, GA. The project consists of: a 28-m high dam, a 0.9-m diam outlet conduit, an emergency spillway, and a 4.0-m diam hard rock transbasin diversion tunnel. This flood-water management system was part of Cities Service Co. mine safety program for the Cherokee ore body, which is partially located within the creek channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1981

By R. W. Braund

THE Tracy mine is within the corporate limits of Negaunee, Mich. The tract of land comprising the Tracy group lies on the east end of the Marquette Iron Range between adjoining mined-out properties on the north and south. Since acquiring the Tracy lands in 1921, Jones & Laughlin Steel Corp. has completed about 115,- 000 ft of surface diamond drilling, partially outlining five orebodies. Now that mining has started, one or more underground drills are in constant operation to obtain information that will aid mine development planning. Some 20,000 ft of underground drilling have been completed to date.

Jan 1, 1958

By M. L. Jeremic

The massive Pb-Zn-Ag sulfide ore body is originated at the contact between the porphyry (footwall) and volcanic (hanging wall). The ore zone is folded and refolded, which results in two different structural geometries of the individual ore bodies. This requires both shrinkage and cut-and-fill mining methods. Strong bedrock resists caving after shrinkage stope completion, so high stress zones are developed below and above the mined area. The cut-and fill system has a limited destressing mechanism, where the stope walls with a backfill exhibiting stress close to a primitive one. This results in closure deformation of the open stope walls, yielding deformations of crown pillars and roof falls of the wide stope backs.

Jan 1, 1985

By W. A. Hustrulid, N. A. Ross

An analysis of the design of medium to hard rock tunneling machines is presented. The developed equations are used to compare performances and machine requirements using kerf and fixed pick cutters to bore a given rock. With the use of pick cutters, required thrusts can be greatly reduced and still achieve the same boring rate as with present day tooth or kerf cutters. It appears that the cutting coefficient, which for most boring machines is of the order of 0.1, should be increased to one or larger to facilitate rock removal by cutting rather than grinding. The depth of cut and the indexing distance should be greatly increased to make use of inherent rock weakness.

Jan 1, 1971

By B. Yu, H. M. Lee, R. P. Gardner

Some preliminary results are given on the use of radioactive tracers for implementing the mechanistic approach to flotation. The process studied is an industrial one for the cleaning of sand for the production of glass. The radioactive tracers employed are those produced from intrinsic elements in the sand by neutron irradiation in a nuclear reactor. The results indicate that the technique will be useful for the determination of flotation simulation mechanistic model parameters on operating industrial processes without interruption of their normal operation.

Jan 1, 1980

By R. E. Sheppard, A. O. Martel

Zinc sinter plant fume is roasted to selectively sulfate the cadmium. Water leaching of the roasted fume recovers about 80% of the contained cadmium and produces solutions containing about 40 grams per liter cadmium and 10 grams per liter zinc. The solution is treated with sodium bichromate for lead removal. Cadmium sponge, precipitated with zinc dust, is briquetted, melted, and cast into commercial shapes. The residue from the water leach is acid leached with waste acid, solubilizing the zinc and residual cadmium. Impure cadmium sponge, precipitated with zinc dust, is separated from solution with cyclones and dewatered in a centrifuge. Air-oxidation- acid leaching of the impure sponge resolubilizes the cadmium. The resulting solution is neutralized, clarified, and treated for cadmium recovery with the water leach solution. The residue from the leached fume is water-washed and recovered in a centrifuge-thickener circuit. This residue contains lead sulfate and significant quantities of gold and silver. Manpower requirements are held to a minimum by automating operations within the Leach Plant.

Jan 1, 1973

Jan 1, 1900

By Raymond Dugdale, Fathi Habashi

There has been a recent interest in studying the action of anhydrous sulfur trioxide on ores to convert the metal values into a water-soluble form as a substitute for leaching by sulfuric acid. For example, Svenke1 converted the small amounts of uranium in slate ash into a water-soluble form by treating the material with SO, at about 600°C. Chao and Sun found that a variety of aluminum-bearing minerals could be sulfatized by SO, in the temperature range 400° to 600°C usually in the presence of a catalyst such as sodium sulfate. Kruse3 patented a process for beryllium recovery from the low grade ore in Utah by first reacting it with SO, at 560° to 750°C then leaching the product with water. In the present report, the action of SO, was examined in the temperature region 100°-300°C which was not investigated by those workers. Experimental Tests were conducted on a beryllium ore sample from Utah, the analysis of which is given in Table 1. It corresponds closely to a saponite ore type as given by Crocker et al. It was in powder form 45% passing a 400

Jan 1, 1973

By A. J. Lynch, N. W. Johnson, D. J. McKee

The behavior of nonsulfide gangue in chalcopyrite flotation circuits has been investigated. Plant and laboratory tests were conducted on five different ores. Linear relationships between the recovery rates of free nonsulfide gangue and water were observed. From pilot plant tests, there was evidence that the linear relationship was actually a linear approximation to a parabolic relationship. There was evidence that free nonsulfide gangue is transported from the pulp to the froth in the water and that the gangue is subjected to hydraulic classification in the froth column. A classification matrix has been proposed to define this behavior. This matrix is suitable for inclusion in a mathematical model of the process.

Jan 1, 1975

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By Colin G. Wilson

This paper considers the heavy liquid laboratory tests used to determine the amenability of a potential ore to the heavy media process. The results of the laboratory testing are correlated to actual plant performance and establish design parameters for the heavy media process. These parameters are used in the development of the metallurgical flow sheet and in the sizing of equipment in the metallurgical plant design.

Jan 1, 1978

By A. Sainato, E. Baker, J. Cervik

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the US is limited to a few plow operations in the deeper parts of the Pocahontas No. 3 Coalbed. The technology for infusing water into retreating longwalls is described and results of a recent Bureau test in the Lower Sunnyside Coalbed demonstrated dust reductions ranging from 47% to 64%. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 2.5 m/s (500 fpm) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23% reduction in operating costs when coal production is increased by changing from unidirectional to bidirectional mining with water infusion.

Jan 1, 1986

By B. R. Coil

One executive writing on capital equipment re- placement stated: "We keep extremely close watch over repair costs and when we reach the point of uneconomical operation, we replace the machine." This, of course, is most elementary, but a very basic premise. However, it seems advisable to set forth several equally obvious principles, so that all discussion will start from the same point. The subject is intended to deal with the point of uneconomical operation due to high operating costs in general and high repair costs in particular. This is not concerned with a similar problem of high costs because of an insufficient number of machines, be they trucks, shovels, or dozers.

Oct 1, 1955

By Geoffrey Purcell

Although the extractive metallurgist has not yet tackled the problem of getting blood out of a stone, he must, when faced with the mini- metal values of today's ores, believe that this ultimate miracle will soon be expected of him. Even assuming that some plausible professor at one of the few remaining minerals industry schools could persuade the National Science Foundation to sponsor such a sanguine research project, the funds might have to go begging for want of a graduate metallurgist. Falling enrollment in fields devoted to nonrenewable mineral resources, long a matter of grave concern to educators, is now recognized as a problem of great national consequence urgently needing a solution. While the law of supply and demand might eventually be expected to right the imbalance of engineers, time is not on our side and action to correct the shortage is required now.

Jan 1, 1970

By W. M. Morris

THE volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrell1 measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0° to 130° F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70° to 250° F. The specific volume in the gas and liquid region was determined at pressures up to 3000 lb. per sq. in. ? throughout this temperature interval. In addition, the vapor pressures were measured at 30° intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0° and 250° F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100° and 460° F. was carried out with apparatus that has been described in another paper (A.I.M.E. Tech. Pub. 1127).

Jan 1, 1939

By T. C. Rao

Oil agglomeration experiments were carried out on coal fines to study the effect of process variables such as pulp density, bridging oil dosage and intensity of agitation on (i) size distribution and (ii) yield of agglomerated product. It has been observed that the growth of agglomerates follows a self-preserving behaviour and using this, a characteristic curve has been derived. This curve has been found to be independent of the process variables. It has also been noted that the growth of agglomerates follows second order kinetics. In an attempt to model the process for predicting the size distribution and yield of agglomerates at different levels of the variables, the cumulative 50 percent of the agglomerates passing size (d50) has been correlated with the variables (i) through the kinetic equation and (ii) directly. These equations, coupled with the characteristic curve can predict the size distribution of the agglomerates at any levels of the variables tested. The yield of agglomerates has been found to follow a definite relationship with d50.

Jan 1, 1984

By Donald K. Weaver

Eight different oil zones have been identified and produced at Santa Fe Springs, of which three or four are in turn divided into two or three parts. These zones, from top to bottom, are the Foix, Bell, Meyer, Nordstrom, Buckbee, O'Connell, Clark and Hathaway, or third Clark. While there has been some difference of opinion over this nomenclature with reference to the different zones referred to as Clark, it has no particular bearing on the water problems. Each of these oil zones has had waters of varying salinity associated with it, either within or at the bottom of the zone. Table 1 is a tabulation of the zones, their maximum thicknesses, salinity and heads of various waters. Surface waters are fresh, and of high head, giving artesian flow in some instances.

Jan 1, 1931

By G. N. Panagiotou

SIMPTOL, a computer simulation program written in FORTRAN IV for use with Cyber 171/8 System at the National Technical University of Athens, describes the mining operations in an opencast lignite mine operating Bucket Wheel Excavators, Conveyors and Stackers. The central objective of the program is to aid management in the selection of a BWE-Conveyor-Stacker System for a given lignite deposit and equipment layout. Much information can be gained from the program with proper manipulation of the input data, which refer to mining profile, soil characteristics, equipment specifications and availabilities and time study data. The other objective of the program is to aid production scheduling in terms of forecasting production rates of the system. The program has been applied to Kardia lignite mine to evaluate its usefulness to represent the actual situation of the system being simulated.

Jan 1, 1983

In situ mining is no longer a "last ditch" approach for recovery of uranium, but a proven and competitive method of exploiting sedimentary deposits. Today, in any feasibility study of uranium properties, the project manager would be prudent to compare the economics of in situ methods with conventional surface and underground techniques. In this comparison of in situ and open-pit mining, John J. Borkert and Carl E. Gerity of Occidental Minerals Corp., evaluated a group of hypothetical uranium deposits using the three most sensitive depositional characteristics of depth, size, and grade. Their conclusion: in situ is generally the better method to maximize total net profits and return on investment. At uranium values of $40 per pound, their analysis found open-pit mining to he unprofitable, generally, when stripping ratios were greater than 30:1, the deposit grade-thickness (GT) was 0.5 or less, or the ratio of depth to GT was greater than 200.

Jan 10, 1978

By Joseph Pogue

THE prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry.

Jan 3, 1924