Search Documents

By W. B. Gogarty

With flow of non-Newtonian fluids in porous media, effective viscosities are needed for use in the Darcy equation. These viscosities depend on the rock parameters and flowing conditions. In this investigation, rheological and flow results were correlated to develop an expression for calculating effective viscosities. Surfactant-stabilized dispersions of water in hydrocarbon were used with consolidated sandstone cores of different permeabilities. The average shear rate in a core was related to the permeability and porosity of the core and the frontal velocity through the core. By using the correlation obtained for determining effective viscosity, experimental and theoretical values were compared for each fluid system by determining average and maximum errors. For the fluid system showing the largest average error, the correlation fit 38 experimental points with an average and maximum percentage error of 4.3 and 14.8, respectively. For the fluid system showing the least error, average and maximum percentage errors of 1.8 and 4.3, respectively, were calculated using 29 experimental points. INTRODUCTION Use of non-Newtonian fluids in the petroleum industry is not new. Fluids of this type have been used for many years as fracturing agents and drilling muds. Recently, attention has focused on the use of high molecular weight polymer solutions for secondary recovery. Results have been reported on studies relating to the flow behavior of polymer solutions in porous media.1-4 Each study gives the viscosity in the Darcy equation as a function of the rheological properties of the fluid, the characteristics of the porous medium and the pressure gradient. The functional forms of the reported expressions differ somewhat in each study. The first three studies used unconsolidated porous media while the fourth used a single consolidated core. Because of the limited information available on the flow of non-Newtonian fluids in porous media, further investigation was undertaken in this area. We selected non-Newtonian fluids that did not contain high molecular weight polymers in order to minimize core plugging. The over-all objective was to gain a better understanding of the flow behavior of non-Newtonian fluids in consolidated porous media. Specifically, our goal was to determine the relationship between the average shear rate in a core and the frontal velocity. Because of this goal, it was necessary to determine the effect of permeability on the shear rate-frontal velocity relationship. We wanted to replace the viscosity in the Darcy equation with an expression relating to the average shear rate in the core and the rheological properties of the non-Newtonian fluid. THEORY For a time-independent, non-Newtonian fluid, the apparent viscosity is a function of the shear rate. This relationship is given by µ = F(v')...........(1) With Eq. 1, a single value of shear rate determines the apparent viscosity at that shear rate. With flow in porous media, a spectrum of shear rates occurs at any average throughput. An average shear rate v' can be used to represent the spectrum of shear rates that exists within the core. By using v' and the rheological data given by Eq. 1, an effective viscosity is determined for the flowing fluid. If v' is the correct average, µe becomes the appropriate viscosity for use in the Darcy equation. Under these conditions, flow rate-pressure drop relationships can be determined for non-Newtonian fluids. HOW the correct average shear rate might be related to the frontal velocity through the core and the characteristics of the porous media will now be considered. Later, the experimental data are presented that indicate the validity of these

By John Hower, Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of greensand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8% ), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of, slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of greensand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace-element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base-exchange; however, the base ex-

Jan 1, 1983

By John Griffen

The modern anthracite breaker or washery uses almost exclusively a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids—coal, slate, pyrite, and clay—and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, requires finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely, and to store, and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,' from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite have been deposited in the rivers draining the coal fields is made evident by the fact that over a quarter of a million tons are recovered annually from the river beds by coal-washing operations.

Jan 1, 1922

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By P. B. Leavenworth

Twenty-six fields were found in the Texas Gulf Coast in 1940 as compared to 17 fields in 1939. Of these, 14 were oil fields and 12 were gas and distillate. About 150 wells were drilling at the end of the year. Production for the year 1940 amounted to 104,127,247 bbl. as compared to 100,-253,937 bbl. for 1939. Considerable wildcatting for Wilcox production featured the exploration, but discoveries were few and the type of fields found mainly gas and distillate. On the whole, the program was discouraging. New Fields Alta Lomu. Galveston County.—The Alta Loma field was discovered on May 20, 1940, by the Stanolind Oil and Gas Company's No. I John A. Hulen, which blew out at a depth of 9166 it. and ran wild for several days, with an estimated production of 400 bbl. per hour of 36" gravity oil from a sand in the top of the Frio. Water soon appeared but the well produced more than I3o,ooo bbl. of oil between May 20 and June 10, together with a large amount of salt water. Later the well was killed and recompleted on Nov. 23, for 276 bbl. of 34" gravity oil per day. Probably this was the most sensational discovery of the year, although development to the end of the year was disappointing. The discovery was the result of reflection seismograph work of the Stano-End Oil and Gas Co., the principal leaseholders. Bailey's Prairie, Brazoria County.— Glenn H. McCarthy9s No. I W. B. Munson was completed in a lower Frio sand from perforations 11,345 to II,349 ft. for 8 bbl. of fluid (50 per cent black oil, 27" gravity, and 50 per cent B. S. and W.) on Sept. 24, 1940. It was finally recompleted as a gas well from perforations 11,631 to 11,651 ft., on Oct. 9, 1940. The well had been drilled to a total depth of 11,860 ft. This well produced for only a short time and the area is at present inactive. Blessing, Matagorda County.—The Texas Company's No. I A. B. Pierce was completed from a Frio sand from 8265 to 8300 ft. on July 8, 1940, for an initial production of 29 bbl. of distillate, I 1/2 million cu. ft. of gas. One other gas and distillate well was completed in 1940. Borden, Wharlon County.—J. F. Hutch-ins' No. 2 A. P. Borden Estate was completed on Feb. 11, 1940, for 108 bbl. of 35,6° gravity oil, from a Frio sand at 4758 to 4771 ft. This is the second well drilled in the area by Hutchins. Two other wells in 1940 were failures and there was no activity at the end of the year. Dyersdale, Harris County.-The Dyers-dale field was opened by the completion, on Sept. 15, 1940, of H. C. Cockburn's No. I G. Burkitt from a sand in the top of the Frio, through perforations from 4067-4072 ft., for 240 bbl. of low-gravity oil. By the end of the year the field had been fairly well outlined and did not appear to be a major discovery. Duck Bay, Calhoun County.—Coronado Oil Company's No. I Welder, alter having drilled to 10,002 ft., perforated casing from 5654 1/2 to 5659 it. and was completed for 60 bbl. of 36.8° gravity oil On July 27, 1940, from a Miocene sand.

Jan 1, 1941

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By B. H. Caudle, R. L. Slobod, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.' These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.'! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

By G. L. Kehl, Emilo Jaraiz F., J. S. Brett

The transformation of eutectoid beryllium bronze has been quantitatively investigated at 550° and 592°C, the temperature region where the products of p decomposition are a fine lamellar eutectoid and a coarse lamellar aggregate which replaces the fine eutectoid with prolonged annealing. Metallographic evidence indicates that the coarse lamellar aggregate forms preferentially in the most densely lamellated regions of the fine eutectoid and favors the hypothesis that the development of the coarse lamellar aggregate in the fine eutectoid is due to the occurence of a cellular segregation reaction. WHEN eutectoid beryllium bronze (Cu-94 pct, Be-6 pct) is isothermally transformed at high temperatures in the and y region after quenching from the fl field, the principal initial decomposition process is G one of growth of approximately spherical nodules composed of a number of lamellar colonies of the a and y phases. After the initial reaction has proceeded substantially or completely, depending on the transformation temperature, a second reaction occurs wherein the fine lamellar eutectoid is replaced by a coarser lamellar aggregate composed of the same oand yphases.' This reaction is not simply a spheroidization of the initial fine eutectoid but the nucleation and growth of a coarser, structurally different, and more stable distribution of the @and yphases. Fig. 1 illustrates the replacement of the initial fine lamellar structure by a coarse lamellar aggregate. The a phase is the dark mottled constituent; the light constituent the y phase. The phase diagram for the copper-rich end of the Cu-Be system2 is shown in Fig. 2. The a phase has the face-centered cubic structure characteristic of copper-rich solid solutions. The B phase is a disordered body-centered cubic structure, while the y phase is body-centered cubic, ordered (CsC1, B2 type). A. viswanathanS investigating Debye patterns of Cu-6 pct Be discovered that a transitory phase appeared on very rapid quenching from the /3 region which was absent when the quenching velocity was moderate. The phase could be assigned a body-centtred cubic structure with a lattice parameter of 2.876. Tempering at 100°C for 2 hr after quenching resulted in complete disappearance of the phase. The work of Fillnow and Mack' is the only previously published study of the isothermal transformation of eutectoid beryllium bronze. Their study elucidated the nature of decomposition at various subcritical temperatures in an exploratory fashion. The purpose of the research reported in this paper was principally to obtain quantitative information on the isothermal decomposition of the fl phase and to clarify the relationships existing between the fine lamellar eutectoid and the coarse lamellar aggregate. EXPERIMENTAL PROCEDURE The material used in this investigation was an almost eutectoid Cu-Be alloy bar furnished by D.J. Mack. The alloy had been melted under a protective carbon cover and centrigugally cast into a graphite mold preheated to 490 "C. Segregation was minimized by violent agitation during melting and pouring. The analysis of the casting was 93.85 pct Cu, 5.60 pet Be with traces of Si, Mg, Mn, Co, and Al. To determine the minimum soaking time necessary to insure specimen homogeneity, a number of specimens were held in the P region at 788OC for times fron 1 min to 12 hr and isothermally transformed at 550°C. Specimens betatized less than 12 min exhibited partial transformation at times shorter

Jan 1, 1961

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

THE subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for 10 years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. I). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, nonmetallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to 100 mg. per sq. cm. per day, the corrosion rate of high-purity magnesium is 0.15 ± 0.05 mg. per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in combination, in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called "tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable. In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0.001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. While the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1941

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,' Zr-Si,' and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies' and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.' Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,' was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By D. J. McAdam

As shown in three recent papers by the author, in two papers by McAdam and Mebs, and in a paper by McAdam, Mebs, and Geil," the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stressest as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strength1 nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. rb and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses. with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. ib shows stress combinations with Sz equal to The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. u shows stress combinations with S2 equal to St. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-II In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1945

By A. Berghezan, E. Bull Simonsen

A simple and general method is described for melting and zone refining refractory metals by induction heating on a specially shaped water-cooled copper crucible. The crucible is the essential part of the apparatus and is placed horizontally. It consists of either a copper plate, or a flattened tube, or of several parallel small diameter tubes all water cooled. The charge lies on the crucible, or whenever possible, is suspended above it. This assembly goes into a transparent quartz tube and the whole is passed through the coil of a radio frequency generator. Vaarious atmospheres can be used. No contamination is detected from the copper crucible. purification is obtained both by selective evaporation of impurities and by zone refining. METHODS of melting and refining relatively large ingots of all reactive and refractory metals as well as some semiconductor materials have been developed in this laboratory during the past several years using induction heating and cold crucibles. These methods are simple and permit the use of a variety of starting materials in preparing ingots of suitable shapes. Among these methods, two are of particular interest. One deals only with the problem of melting without contamination. In this method the induction coil has a specially designed shape and acts simultaneously as heating element and crucible. The second goes one step further, being designed for both melting and further purification of the refractory metals. The aim of this paper is to describe the second method which is of more general interest and of greater applicability to metallurgical problems. A) THE PRINCIPLE OF THE MELTING AND PURIFICATION METHOD As originally proposed by one of us1 the method consists of heating a charge of any refractory metal or semiconductor material to the melting point on a water-cooled copper crucible by passing both the charge and the crucible through the induction coil of a radiofrequency generator. Although both are subjected to the same induction field, one achieves the melting of a refractory metal on a copper crucible even when the refractory metal has a melting point of more than 2000°C above that of the crucible. This seemingly "odd" method works effectively for the following reasons. Because of its high electrical and thermal conductivity as compared with the material being melted, copper can be used as the crucible and kept at a low temperature while the material is heated by induction to its melting point. With water Silver and other highly conducting materials can also be used. If a nonconducting material is contemplated, e.g. SiO or a high polymer, a very thin wall should provide efficient cooling. cooling through ducts in the crucible its temperature can be kept between 40" to 70°C; thus its electrical resistivity is kept low, while the resistivity of the charge increases rapidly as its temperature is increased. B) APPARATUS The crucible is the essential part of the apparatus. It has been designed in various shapes depending on the atmosphere used, whether vacuum or an inert gas or hydrogen. In all crucible designs an effort was made to reduce its volume to "nothing but the cooling water" in order to avoid shielding the ingot from the induction field. In practice it is either a

Jan 1, 1962

By R. Al-Hussainy, H. J. Ramey

Previous gas well test analyses have been based mainly upon linearizations of ideal gas flow results, although a method for drawdown analysis based upon real gas flow results has been proposed. Linearizations based upon ideal gas flow require estimation of gas physical properties at Tome sort of average pressure, and implicitly involve the assumption that pressure gradients are small everywhere in the reservoir. A new real gas flow equation has been developed by means of a substitution which couples presTure, viscosity and gas law deviation factor. This sub-stitution has been called the real gas pseudo-pressure. Use of the real gas pseudo-pressure leads to simple equations describing real gas flow which do not contain pressure-dependent gas properties, and which do not require the assumption of small pressure gradients everywhere in the flow system. Equations required to determine flow capacity, well condition and static formation pressure from pressure drawdown and build-up tests with the real gas pseudo-pressure concept are presented. Also shown are applications of the real gas pseudo-pressure to back-pressure testing, the gas materials balance and rigorous determination of average gas properties for previous gas flow equations. Included are sample calculations for well test analyses. INTRODUCTION A recent study' of the flow of the transient flow of real gases in ideal radial systems showed that it is possible to consider gas physical property dependence upon pressure by means of a substitution called the real gas pseudo-pressure. The substitution has the advantage that it enables engineering solutions for steady and transient flow of real gases that are more accurate and general than those previously available. The solutions are particularly important for the case of gas flow in tight, high-pressure formations under large drawdowns. Even for more ideal flow conditions, the real gas pseudo-pressure concept leads to important rules for finding average gas physical properties pertinent for older well test analyses. Ref. I provides a detailed study of the theory behind the real gas flow correlations to be used in this paper. The purpose of this paper is to provide necessary engineering forms for use of the real gas flow results, and to illustrate applications. The following considers flow of real gases in an ideal radial flow system. It is assumed that: (1) formation thickness, porosity, water saturation, absolute permeability, temperature and gas composition are constant; (2) gas compressibility and density are functions of pressure as described by the gas law pv = znRT; (3) gas viscosrty is a function of pressure; (4) effective permeability to gas may be a function of pressure to account for liquid condensation; (5) condensate is immobile; and (6) the formation has no dip.

Jan 1, 1967

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By W. A. Walker, G. W. Ostroot

An increase in the number of deep wells being drilled where extreme bottom-hole temperatures are encountered, and the anticipated drilling of wells where temperatures in the range of 500°F or higher may occur, has brought about a comprehensive investigation of cementing materials and of the techniques involved in their proper usage at these elevated temperatures. Included are developments in cements, retarders, weighting materials and other cement additives which make it possible to formulate a variety of compositions to help resolve the cementing problems of these extreme well conditions. The problems associated with the selection and testing of cements are discussed, and a resume of field results is included. Previous studies on strength retrogression indicate that caution should be exercised in the selection of a cementing composition for use in high-temperature wells. It now appears that, by the addition of silica flour as a stabilizing additive to certain cements, compositions covering a wide range of slurry densities can be designed to meet extreme well conditions without strength retrogression. Improvements in cement retarders make it possible to produce a four-hour thickening time at static temperatures up to 500°F. This temperature is considerably higher than conditions presently being encountered in drilling and completion work. Inert weighting materials, used to produce 20-lb/gal or heavier cement slurries, are reviewed. INTRODUCTION As the search for oil continues, the number of wells being drilled to depths of 10,000 ft or below has continued to increase over the past decade. During 1959, there were 50,893 wells drilled in the United States for a total of 209 million ft of hole. Of this total, approximately 4.45 per cent were drilled below 10,000 ft and 0.30 per cent below 15,000 ft, with a record depth of 25,340 ft recorded (Table 1). With the drilling of this record-shattering hole comes the question, "How deep can wells be drilled?".' Limitations with respect to equipment (surface and subsurface), cementing materials and techniques would cause some concern; however, a panel of experts have agreed that the U. S. oil industry has the equipment and know-how to drill a 50,000-ft hole. The greatest deterrent would be the 700°F temperature they would anticipate encountering at this depth. Although the number of wells drilled under what is generally considered hot-hole conditions (230°F and higher) has been relatively high, each well often presents distinctly individual problems and requires separate consideration and selection of special materials, techniques and equipment. At the present time there are over 30 additives and special cements available for use in "tailoring" a cementing composition for a specific well. It is not uncommon to use three or four different additives with the basic cement to produce the desired slurry characteristics. A generally accepted procedure is to make laboratory tests on selected cementing compositions prior to pumping them into wells deeper than 12,000 ft, or where static temperatures are in the range of 260°F or higher. In some instances, it is recommended that laboratory tests be made where less severe well conditions are encountered. Prior to selecting a cementing composition for a particular well, key personnel representing the operator, drilling contractor and service company should meet to determine that each individual is acquainted with every detail which might influence cementing results and to discuss the execution of the job. For cementing hot-holes, a number of factors must be evaluated before proceeding with the operation. Consideration must be given to the following. 1. Thickening time—The slurry must remain fluid for a sufficient length of time to allow displacement down the casing and up the annular space in a primary cementing job or, in squeeze-cementing, adequate thickening time for both the build-up of a satisfactory squeeze pressure and the reversing out of excess cement. The thickening time of standard retarded cements will often be too short under extreme temperature conditions, thus involving special formulations and requiring laboratory tests to determine the proper amount of additional retarder to obtain the desired pumpability.

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

[Cyanidation: Fresnillo, Mexico. 112. 734, 739. Abs.. YB84. 34 gold ore: before or after amalgamation. respective merita. 118, 538 high residue avoided by milling in water, 118, 542 Homestake mill, 112,607. 614 impoverishing gold ore before cyanidation justified. 118, 539 Kirkland Lake district, 112, 648, 649. Abs., YB84.32 literature prior to 1932. See Source Book. McIntyre Porcupine mines, 118, 638 mercury as an aid to extraction of gold, 118, 53 8]

Jan 1, 1936