Search Documents

By Cyril Stanley Smith

Although not of the same importance as electrical conductivity, the capacity for conducting heat is nevertheless a very important property of metals and alloys. A knowledge of thermal conductivity is of value in selecting alloys for many purposes and in the calculation of the efficiency of apparatus which is being designed. Unfortunately, the determination of thermal conductivity is extremely slow and tedious, consequently few data have been obtained. A further reason for the lack of information is that there has long been an impression that the thermal conductivity of an alloy is directly proportional to the electrical cónductivity and that it can therefore be calculated from the latter. The Wiedmann-Franz-Lorenz law of constant ratio of the two conductivities holds with a considerable degree of precision for all the pure metals, but appreciable deviations occur in certain alloys—particularly those containing nickel—and it seems difficult to predict exactly what the ratio will be. Therefore direct determinations of thermal conductivity should be made whenever the results are needed with any accuracy. This research is intended eventually to cover all the alloys of copper that are of commercial importance, including the binary alloys of copper with zinc, tin, aluminum, nickel, silicon, manganese, cadmium and phosphorus, and the ternary alloys copper-nickel-zinc, copper-nickel-silicon, copper-manganese-silicon, copper-zinc-tin, etc. Most of these alloys are customarily used in the wrought condition and therefore were tested in the form of annealed rods. A limited number of sand castings were also obtained and examined. This paper contains a complete review of all the previous work that has been done on copper alloys, and includes a detailed description of the apparatus and method of procedure used in the present research, together with the new results obtained on the copper-zinc series, which is the only one completed at the present time. Subsequent papers describing the other alloys will contain the experimental results and discussion only. Previous Work Copper The conductivity of copper has been studied by many observers since the pioneer work of Wiedemann in 1859. The majority of these measure-

Jan 1, 1930

By John Brown

As a part of a symposium on the relations of structure to ore deposi-tion, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replace-ment deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifica-tions, to mineralization in unmetamorphosed limestone. In metamorphosed forma-tions, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a lime-stone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone-is of little or no importance.

Jan 1, 1940

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By Wm. D. Owsley, R. E. Moeller

In the petroleum industry, the process known as oil well cementing is the equivalent of pressure grouting in the mining and construction industries. The science of oil well cementing has been known and practiced for many years. At the present time it has been brought to a high degree of perfection in the handling of many different types of jobs, all of which are known as oil well cementing. In order to understand more easily these processes, we will discuss briefly several different types of oil well cementing jobs, the purposes for which they are performed, and the methods of their accomplishment. It is believed that some of .these procedures, in a modified form, can be applied to pressure grouting projects in general. Originally, oil well cementing consisted of placing a neat cement slurry about a steel casing set in a bore hole. Cement is used about these casings to protect them from the corrosive effects of ground waters, to protect the oil and gas zones from encroachment of undesired water from other levels, to prevent the blowing out of high pressure oil and gas zones from shallow levels, and to strengthen generally and support the casing being placed in the bore hole. After the bore hole is completed to the desired depth, casing is run into the well, pumps are attached to this casing and circulation of the mud fluid in the hole is established; this circulation being from the inside of the casing into the annulus about the casing, and thence back to the surface. Next, a cement slurry is mixed and pumped into the inside of the casing string, A plug, which acts as a piston within the casing, is placed above the cement slurry. This is to separate the top of the cement slurry from mud or water which is used to shove the cement down through the casing and out into the annulus. This plug further serves the purpose of shutting off against a baffle in the bottom end of the casing string, thus stopping the flow of cement out of the casing and leaving the shoe, or lower end of the casing, surrounded by cement and also filling the annulus there above. Casing strings cemented in the above described manner may vary in length from a few feet of large diameter pipe to very long lengths of smaller pipe. As of the present date the longest string of casing which has yet been cemented is some 16,600 ft deep. As a general rule, the deeper the well and the more cement slurry used, the higher the pressures which are required to place the slurry. In parts of West Texas, it is not uncommon to use 4000 sacks to cement a single string of casing in place. Machinery used to mix the cement and place it into the casing is mounted on heavy duty, powerfully equipped trucks which are capable of negotiating any type of highway or country roads. These trucks

Jan 1, 1949

By C. E. Lesher

COAL has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads .of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. NEED FOR COAL RESEARCH To utter "Research" is to use the modern magic word; to conjure up the miraculous-rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privately financed research is just started in the Pennsylvania, anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 25 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200, 000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By Robert P. Roberts

In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows: The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was determined with a stop-watch, and this figure, combined with the in-

Jan 1, 1914

By Seymour Fiekowsky, Alvin Kaufman

Taxes are compulsory charges levied by a government for its support. They are usually paid to support the general services provided by government rather than special services (such as safety inspection). The latter are normally supported by user charges often called license fees. Taxes are used by national governments not only to raise money but also as a part of fiscal policy. As such, taxes are used to stimulate or deflate the economy, as an incentive to save or invest, as a means of allocating national resources, and as a means of redistributing income. In our discussion, we will deal only with those facets of the subject that relate specifically to the mineral industry. In doing so we will deal with taxes levied on all industry in a generalized way and only insofar as it affects our industry, but at some length on those portions of the tax system related directly to the mineral industry. It is not our intent to provide a "cookbook" for computing taxes, but rather to present some of the policy issues that bedevil those who must develop our tax policies. MINERAL TAXES The mineral industry is subject to the full range of taxes levied by governments. These include taxes on income, property, and sales, as well as excise and severance taxes. The latter are somewhat similar to a royalty in , that such taxes are levied either ad valorem or per unit of output. Severance taxes most commonly are charged to oil and gas output, although coal, salt, sulfur, and iron ore production also have been taxed in this manner. The major governmental advantage of the severance tax is the administrative ease of collection. On the other hand, it poses an addition to cost independent of profitability. As a consequence, the severance tax can cause premature abandonment if mineral product prices do not rise sufficiently to cover it. Such a rise may not occur if differential tax rates are levied by the various states. Property taxes normally are levied on all property owners, including mineral owners. The major difficulties in this kind of tax, in so far as mining is concerned, are erratic valuation coupled to the inherent problems involved in assessing a property where the extent and richness is chiefly unknown. The impact of these taxes, including state income taxes, is reduced somewhat, as they are usually deductible from gross income as a business expense with a consequent lowering of national income taxes. The net cost of severance, property, sales, and state or local

Jan 1, 1976

By W. C. Winegard, E. L. Holmes

The effects of the solute elements lead and bismuth on grain growth in zone -refined tin have been investigated. At low temperatures, viz. below 160°C. or at high concentrations, viz. greater than 0.03 at. pct, the temperature dependence of grain growth was found to be constant. A correlation was found to exist between the rates of grain growth in the presence of solute impurities and the factor [C Ir - 1]2 , where C is the solute concentration, r is the radius of solvent atom, and r' is radius of solute atom. It is shown that the Liicke and Detert theory does not give a satisfactory explanation of the results obtained. INVESTIGATIONS of grain growth in zone-refined lead and tin and some effects of solute elements on grain growth in these metals have been reported by Bolling and winegardly2 and Holmes and winegard? The present investigation is an extension of the previous work, and was undertaken to provide additional results which might make it possible to discover the mechanism whereby the rate of grain growth is affected by the presence of foreign solute atoms. The experimental procedure was exactly the same as that described previously.3'4 Figs. 1 and 2 show the results obtained with lead and bismuth additions over the same temperature range, viz. 167" to 220°C, as that used for the investigation of grain growth in zone-refined tin.3 Fig. 3 shows the results obtained for zone-refined tin and for this tin with lead solute additions over an extended temperature range. DISCUSSION OF RESULTS As mentioned previously,3 the character of grain growth in the particular zone-refined tin used in these experiments appears to change as the temperature of annealing falls below about 160°C. The grain growth became somewhat irregular and was characterized by a jaggedness of many of the grain boundaries. The reason for this change is not known, but may be due either to residual impurity effects or possibly an oxide precipitation. It was obvious that normal grain growth only occurred in the zone-refined tin through the high-temperature range 167" to 220°C, and so the effects of solute atoms on grai11 growth over the two temperature ranges will be discussed separately. a) Effect of Impurity on Grain Growth in the Temperature :Range Above 167°C. It is apparent from Figs. 1 and 2 that, for low concentrations of solute, the rates of grain growth tend towards a common value as the melting temperature of tin is approached. As the concentration of lead is increased, the rate of grain growth close to the melting temperature is also reduced, and at high concentrations the temperature dependence of the rate of grain growth appears approximately constant. It should be noteil that the effect of bismuth is greater than that of the same concentration of lead, but both these solutes have a smaller effect on the rate of grain growth than silver, as seen from an earlier investigation of Holmes and Winegard. It should

Jan 1, 1962

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By G. Sherburne Rogers

One of the features of oil-field work that puzzles operator, chemist, and geologist alike, is variation in the gravity of the petroleum produced on neighboring leases or even from adjoining wells. Few fields in the United States yield oil that is of uniform gravity throughout; in some fields the different grades are produced from different sands, in a few from different formations, and in many from different areas in the same sand. In a few cases, perhaps, a common assumption—that the heavier oil is derived from the lighter through the escape of the more volatile constituents—is valid, but many cases can not be explained in this way. Although in the California fields the specific gravity of the oil generally decreases with depth, there are numerous exceptions to this rule; and, as in many other regions the light oil is found nearest the surface, it is evident that evaporation underground is generally an unimportant factor. It is generally recognized that the great differences between petroleum from widely separated fields are due largely to differences in age and degree of metamorphism and to variation in the composition of the original organic matter; but in the writer's opinion some of these broader differences, as well as most of the minor variations in the character of the oil from any one field, are due to the local action of natural reagents such as sulphur or oxygen. This is particularly likely to be true if the oil has migrated from one formation to another, as in the California fields; and in some arcas it appears that variation in sulphur content may even afford a rough index of the extent or distance of the migration. It is the purpose of this paper to call attention to the chemical action of sulphur and oxygen on petroleum, to show that the gravity of the oil from any one field is intimately related to its sulphur content, and to discuss the possi-

Jan 1, 1918

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946

By Clarence Zener

[ ] THE present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 27 to 30. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1946

By E. W. Shaw

Continued discussion of the paper of Roswell H. JOHNSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162. E. W. SHAW, Washington, D. C. (communication to the Secretary+). -With the word petrology-literally the science of rocks-being used primarily for igneous rocks, and with geophysics coming to mean the study of lavas and the rocks into which they solidify, contributions to the knowledge of the physical chemistry of sedimentary rocks, even though only ideas which may be used as working hypotheses, become most welcome. The forces which control the formation and subsequent history of the stratified portions of the earth's crust are so little known that no one has yet been able to settle finally the questions as to whether petroleum is of organic or inorganic origin; whether it originated far from its present position, or nearby. Yet both the chemical and physical problems of the rocks in which oil occurs seem to be more simple than those of the igneous rocks. The oil-bearing rocks of western Pennsylvania, for example, have in all probability never been subjected to a pressure exceeding 3,000 or 4,000 lb. to the square inch, nor to a temperature higher than 100° or 200° C. These pressures are considerably below the crushing strength of rocks, and the temperature far below their melting point. The igneous rocks,, on the other hand, have been affected by enormous pressures and very high temperatures and yet steady progress is being made in reproducing in the laboratory the conditions of their formation and subsequent modification within the earth. The solution of the sedimentary-rock problems would seem to be fully as important as those of igneous rocks, and yet we must content ourselves with reasoning backward and our inferences as to what has happened are oftentimes little more than guesses.1 One of the fundamental problems is the origin of the salt water in oil fields. Is the salt water fossil sea water; has it been formed by the solution o-f salts of various kinds from distinct beds, from disseminated par-ticles, and from the weathering of suitable grains in the rock; or is it of deep-seated origin? Its general resemblance to sea water points to the first, but the principles held by some concerning the free circulation of water throughout the earth's crust, and certain peculiarities of composition indicated by the few analyses available, seem out of harmony with such an explanation.

Jan 7, 1915

By Orville R. Lyons, A. C. Richardson

THE Coal Division of Battelle Memorial Institute, during the course of an investigation conducted for a coal producer, carried out extensive sampling of the fine-coal section of a preparation plant. The information obtained during the testing period was used to evaluate the overall plant operation and provided the basis for. recommended changes in the plant flowsheet. Included in the information were data for the results obtained when using a Bird centrifuge to dewater the particular coal being treated. At the completion of the investigation, the coal producer gave Battelle permission to publish the operating data for the Bird centrifuge in order to make this information available to the coal industry. The authors wish to take this opportunity to express their appreciation to this company and its officials for their willing cooperation in the matter of publication. Description of Preparation Plant: The preparation plant on which the data were obtained is primarily a jig plant. The coal being washed is a low inherent moisture, friable, Pocahontus-type. The washed coal from the jig is dewatered and sized at 1/4 in. by a Parrish-type dewatering and sizing screen. The minus 1/4-in. coal and the underflow water from the shaker screen flow to a sludge tank where, after the coal settles, the coal is conveyed by a flight conveyor into a pump sump. The pump, a 300-gpm sand pump, delivers a mixture of fine coal and water to a Bird centrifuge which produces a dewatered cake and an effluent. At the time when the investigation was made, the centrifuge effluent was returned to the sludge tank and the cake product was mixed with a coarser size of coal prior to loading into railroad cars. The semiclarified water from the sludge tank overflowed into a pump sump from which it was pumped to the jig. As originally designed, the preparation plant was intended to operate with a closed water system but it was found, soon after operations started, that for various reasons this could not be done. In order to provide for removal of excess water from the system and to aid in maintaining the desired minimum percentage of solids in the circulating water, the plant was operated to provide from the sludge tank a continuous overflow of water and fine solids that was sent to waste. The centrifuge feed represents approximately 35 tons per hour of minus 1/4-in. coal in the form of a pulp averaging 38 pct solids. Sampling Procedure: In order to obtain basic data for determining the relationships existing in the fine-coal section of the preparation plant, samples were obtained for: (1) the centrifuge feed, (2) the centrifuge cake, (3) the centrifuge effluent, and (4) the circulating water. The sampling was arranged to start on a Monday, in order to begin operations with a sludge tank full of fresh water, and was continued long enough to allow sufficient time for fine solids to build up within the water system or for a two-day, four-shift operating period. All samples were taken at half-hour intervals except when plant stoppages occurred. After a stoppage the plant was

Jan 1, 1951

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen's Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen's Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen's Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen's Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

By G. W. Maynard

In this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporay suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our owu Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in september, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith's fire, metallic iron is formed, which, on being heated to the welding-point on the same smith's hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxiug materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slog." This is the keynote of the Siemens direct process. Dr. Siemens says further: " If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, arid the fusion of the earthy matter mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, weshall rind that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonsceous matter per ton of iron contained in the ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976