Search Documents

By R. V. Ramani, T. S. Kovach

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas that have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development, and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1985

By T. W. Healy, M. S. Moignard

The use of electrokinetic or zeta-potential phenomena in studies of the properties of mineral sulphides has increased greatly over recent years. This review aims to examine and discuss the body of literature on the subject of electrokinetic properties of sulphides in a comprehensive and critical manner. Although the review covers the period from 1925 to 1975, it is only in the past ten years that researchers have been fully aware of the implications and problems of chemical reactions, notably oxidation and precipitation reactions, on the surface properties of sulphide minerals. These papers are discussed in more detail than the earlier publications. A table containing a list of determinations of iso-electric- points and points-of-zero-charge of mineral sulphides, and the methods employed in obtaining these results, is presented.

Jan 1, 1976

By R. D. Reiswig, D. J. Mack

THE use of pyrophoric alloys in ignition devices dates back more than fifty years to a German patent granted to Carl Auer von Welsbach in 1903.' This patent named a composition essentially the same as that used in most present-day cigarette lighter "flints:" 70 pct mischmetal, 30 pct Fe, referred to here as "Auer alloy." Among the few current exceptions to this composition are those "flints" based on titanium or zirconium. The rare-earth metals of which mischmetal is composed are so similar chemically and physically remarkable similarity in their alloying behaviors would be expected. Comparison of the binary phase diagrams2 of these elements with nonrare-earth metals shows that this is true to a striking degree, so much so, in fact, that it appears that a mixture of these elements may be treated as a single component of alloys without fear of serious error. In considering alloys containing mischmetal, therefore, the mixture of rare-earth elements will be referred to merely as "cerium," the predominant element in mischmetal. In polishing cerium alloys for metallographic examination, it was soon discovered that aqueous polishing media were highly corrosive. Free cerium in the alloys acts similarly to calcium (though not quite so rapidly) in evolving bubbles of hydrogen at the metal-water interface; thus, special metallographic techniques are required. The simplest polishing technique found to be satisfactory consisted of slow hand grinding on dry emery papers through

Jan 1, 1956

By T. A. Rickard

The question of the original extent of the anthracite-beds of Pennsylvania has often been raised; and even discussed with reference to the probability of their present existence under the New Red, a matter of immense practical importance. So high an authority as my revered master, J. P. Lesley, Honorary

Jan 1, 1903

By G. R. Fritterer

INVESTIGATORS in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial tempera-tures; i. e., 1000° to 1800° C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree.

Jan 1, 1933

By John J. Howard

WE are approaching the depletion of our principal source of iron ore-the Great Lakes deposits, which have provided 85% of the nation's requirements for the past fifty years. This situation presents a threat to our standard of living and our position as a world power. Fortunately, in the Great Lakes region there are still tremendous quantities of potential iron ore in the form of the low iron, high silica rock called taconite. The economical extraction of iron from taconite will insure our future steel supply if no new deposits available to the United States even in time of war are discovered. In the new process presented here, the iron is reduced directly by a simple method and then separated from the silica. The product is "feed," not to the blast furnace, but to the steel plant. This process requires very much less plant, less physical and chemical treatment, and less fuel and auxiliary materials than the conventional ore concentration-blast furnace method. In my opinion, this new, fundamentally different approach offers a better hope for the solution of the iron ore problem.

Jan 5, 1950

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By M. Muskat, H. H. Evinger

A METHOD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous- fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permeability data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should have significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast.

Jan 1, 1942

By Earl A. Gulbransen, Kenneth F. Andrew

DRY oxidation of zirconium has been studied by several groups.'" The present work extends our early study1 to the high-temperature studies of Cubicciotti2 and Belle and Mallett.8 ulbransen and Andrew1 showed that the parabolic rate law fitted the 2-hr experiments between 200" and 425°C after an initial deviation. An energy of activation of 18,200 cal per mol was calculated. Cubicciotti,' in a study between 593" and 880°C, showed that the parabolic rate law fitted the data and an energy of activation of 32,000 cal per mol was calculated. In contrast to these studies on sheet specimens, Belle and Mallett3 studied the oxidation reaction on rod specimens and found a cubic rate law to fit the data.

Jan 1, 1958

By L. B. Lindemuth

TO those who are in a position to carry the thought to a conclusion, I would like to present a theory of the cause of blisters in ' galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered, because the reason for their formation is entirely obvious. Blisters that periodically occur, with no apparent system of location, number, size or grouping, and then disappear with no apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pres-sure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots, were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or wash-ing, and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening which it entered as moisture. The pressure so generated forces the sheet apart along those lines of lamination that may be found in practically all flat sections of steel rolled comparatively cold.

Jan 5, 1927

Expect Labrador Iron Ore Shipments by 1954 Iron ore shipments from the Quebec-Labrador area are a "definite expectation" by late summer, 1954, according to William H. Durrell, general manager of the Iron Ore Company of Canada. About $120 million have been invested in the project, with a total of $200 million expected to be reached before a ton of ore is shipped, Mr. Durrell said. According to the general manager approximately 418 million tons of open pit highgrade ore have been proven in the project. Deposits lie several hundred miles north of the mouth of the St. Lawrence River in territory which was without transportation of any kind. Construction of a railroad from Seven Islands to Knob Lake, about 360 miles, is an important part of the development plan. The railroad will be the first to adopt complete roller bearing applications. Construction is on schedule with 215 miles of the route graded. Completion involves two tunnels through rock, one of almost half mile length, a 700-ft bridge and several smaller spans.

Jan 3, 1953

By K. Robert Dorman, F. Michael Jenkins

The occurrence of rock bursts in deep metal/nonmetal mines presents a major hazard to their safe and economical operation. As part of a Bureau of Mines program to reduce rock bursts in deep vein mining, a project was conducted in the Coeur d'Alene Mining District of Idaho to evaluate and demonstrate the mining of a destressed sill pillar using undercut-and-fill methods. A 50-ft sill pillar in a burst-prone area was preconditioned by drilling and blasting vertical holes in the ore. After raises were driven through the destressed pillar to the level above, it was mined by the undercut-and-fill method. The conclusion from this demonstration is that the combination of ore preconditioning and underhand mining resulted in greatly improved rock burst and ground control, allowing safe and efficient mining of a potentially hazardous, burst-prone pillar.

Jan 1, 1984

Jan 4, 1951

By B. C. Craft, T. J. Johnson, H. L. Kirkpatrick

Petroleum engineers are displaying considerable interest in the problems of cementing oil wells, especially in the Gulf Coast and California areas, where steep temperature gradients are encountered and where wells are being drilled to greater depths. Deep drilling, that is, at depths in excess of 7000 ft., has been undertaken in these areas only in the last few years and with this trend oil-well cementing requires more technical treatment. It is not the purpose of this paper to describe the scope and application of cement operations in the oil industry or to give the standard specifications, methods of sampling and testing of portland cement. The various testing methods have been described by the American Society for Testing Materials1, Uren2, Tickell and Wankowski3 and Rakestraw and Parsons4. The latter authors (pp. 50-58) have also described in detail the methods of cementing. The authors realize that it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist at great depths, but an attempt has been made to scale down these dimensions proportionally. The selection of problems to be studied was based largely upon the practical questions asked by several of the largest operators in these fields. All cements used in these experiments met the specifications of the American Society for Testing Materials.

Jan 1, 1935

By Harvey S. Chase

During the recent great depression in iron, little has been done in the magnetic separation of iron-ores; and previous to the present decade the art was in its infancy, so that there were few, if any, successful separators on the market, and but scanty practical data could be obtained as to the industry itself. Moreover, the recent development of the great Mesabi Bessemer beds, coincident with the intense depression in business, has discouraged active attempts to solve the problems presented in the crushing and separation of the refractory magnetites of the South. Experiments have been carried on, however, upon a practical scale in separating these ores magnetically, at the well-known Cranberry mines, in Mitchell county, N. C., with results which are encouraging. The magnetites of the Blue Ridge, in the South, have been known, and the soft ores of the region have been used in Catalan forges, since very early times. The original settlements in East Tennessee were made along the Watauga river by Daniel Boone, William Bean, John Sevier, and other stalwart pioneers; and this valley lies parallel with the " Cranberry " lead, which is undoubtedly the most celebrated and the most extensive deposit of workable magnetic ore in the Southern States. This lead I have personally traced along the outcrop, be-

Jan 1, 1896

By John D. Ridge, Robert C. Barwick

The amount of lead in concentrates that moved in international trade in 1952 was only 16 pct of the world mine production of lead and was less than 27 pct of the total of lead in concentrates and lead metal that traveled from one country to another. Because almost all lead is derived from galena, lead concentrates are high grade, with a theoretical maximum of 86 pct lead, and can be shipped as such without transporting a considerable weight of waste material. It would not be surprising, therefore, to find the large share of lead in international trade moves in concentrates (Rule 5). This is not, as has just been mentioned, actually the case. There is more than one explanation for the situation. Lead smelting is not a particularly difficult process and is one for which smelting equipment can readily be made of the best size for the tonnage to be handled. Another factor that encourages local smelting is the effort of many mining countries to see that a maximum of profit from their raw materials remains in the home country. Still another factor is the newness of large scale lead mining in two of the three largest exporters of lead in concentrates. In these countries, South West Africa and French Morocco, there has not yet been time to erect enough smelting capacity to process all of the concentrate output. Even in these countries, however, it will not be long, if present trends continue and plans are fulfilled, before most or all of the lead mined is domestically smelted.

Sep 1, 1955

Covering resources, production, uses, defense impact, and future outlook of nickle, Mining Engineering presents the third in a series of articles on strategic minerals. Preceding it are "Cobalt" in January and "Sulphur" in May.

Jan 8, 1951

By Josef Westesson

No question in the metallurgical chemistry of the present day seems to be so difficult to agree upon as the determination of phosphorus in iron and steel. To my knowledge, there are at present at least three different methods in use in the iron laboratories of the United States, viz.: The citric acid method, the molybdate-magnesia method, and the direct molybdate method,—the last-named method having been lately adopted. Each of these methods has its advocates, who take every pains to prove its advantages, and the incorrectness of the others; and much has been written for the purpose of securing the use of a standard method—as yet, however, without any result. There is no doubt, or ought to be none, that each of these methods gives correct results, when it is carefully conducted and every precaution is taken. But it is not only correct results that we want nowa-days. The demand is great, also, for getting results in the shortest possible time. I think it has been sufficiently proved that the direct molybdate method, the weighing of the precipitate, answers well in both respects. Being a pupil of Prof. Eggertz, I have myself used his method for years until quite recently, as it is described by Mr. Troilius in our Transactions, vol. x., p. 166 (but with some slight modifications), and I can safely say that the results of this method agree well with those of the molybdate-magnesia method. I have, moreover, been checked, in a few instances, by some of the

Jan 1, 1885

By R. P. King

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976