Search Documents

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

Jan 1, 1923

By Willard L. Hunter

Four solvent extraction systems were studied to determine their efficiency jor extraction and separation of tantalum and columbium. Aqueous feed solutions of varying HF-HCl concentrations and metal content were contacted with equal volumes of cyclohexanone, 3-methyl-2-butanone, and 2-pentanone and solutions of varying HF-H2S04 concentrations were contacted with equal volumes of 2-pentanone. One multistage continuous test was made in a polyethylene pulse column using cy clohexanone as the organic phase. In each system studied, columbium and tantalum purities in excess of 95 pct with respect to each other were obtained in single-stage tests at low acidities in the feed solution. Separation factors ranging from 1700 to 2400 were obtained when rising HF-HCl mixtures in the aqueous phase. Best results were obtained when a solution of HF-H2S04 was used as the aqueous phase and 2-pentanone as the organic phase. A separation factor in excess of 6000 was obtained in one stage with aqueous solution concentrations of 2 _N HF and 2N H2S0,. When acid concentrations were increaszd to 52 HF and 10 _N H2S0,, 99.9 pct of the tantalum and 98.2 pct of the columbium initially present in the feed solution were transferred to the organic phase. The separation of columnbium and tantalum obtainable by means of the solvent extraction systems presented in this paper was found to corn -pare favorably with other systems, including the HF-H2SO4-methyl isobutyl ketone system currently used by most producers for the extraction and separation of these metals. TANTALUM and columbium are always found together in minerals of commercial significance, although the proportion of the two metals in ores varies within broad limits. Columbium is estimated to be 13 times more abundant than tantalum. Five methods generally employed for the separat:ion of these metals are: 1) fractional crystallization (the Marignac process),2 2) solvent separation, 3) fractional distillation of their chlorides, 4) ion exchange, and 5) selective reduction. Of these methods, the one currently used by industry to the greatest extent is that of solvent separation. One of the early technical developments in solvent separation of tantalum from columbium was reported by the Bureau of Mines: the HF-HC1-methyl isobutyl ketone system; data were presented for both laboratory and pilot-plant experimentation.3 Of twenty-eight organic solvents tested for their ability to extract tantalum from an HF-HC1 solution of columbium and tantalum, 3-pentanone (diethyl ke-tone), cyclohexanone, 2-pentanone, and 3-methyl-2-butanone were chosen for further study. Data on the HF-HC1-diethyl ketone system has been published4 and data describing the use of cy clohexanone, 2-pentanone, and 3-methyl-2-butanone as the organic phase are included in this report. RAW MATERIAL The source of tantalum and columbium oxides for this study was ('Geomines" tin slag from the Manono Smelter, Cie Geomines, Gelges, S.A., Congo. In order to extract the valuable Ta-Cb content, the slags were carbided, chlorinated, and the sublimate from chlo-rination was hydrolized and washed free of chloride with water. The washed material was air-dried and stored in a stoppered container. Throughout the paper, "feed material" refers to this mixture of hydrated oxides which was employed because of its high solubility in aqueous solutions. Typical analysis of the hydrated oxides is shown in Table I. I) HF-HC1-CYCLOHEXANONE SYSTEM Batch Separation. Effect of Acid Concentration. To determine the effect of varying the acid concentration upon the transfer of tantalum and columbium, a series of tests was made in which approximately 2.5 g of feed material was added to 25 ml solutions of 2, 4, 6, 8, and 10 N HF and 0 through 5 N HC1. Tantalum pentoxide concentration of the solu%ons was approximately 21 g per liter and columbium pentoxide was 14 g per liter. These starting solutions were shaken with equal volumes of cyclohexanone in 100 ml polyethylene bottles for 30 min. The phases were carefully separated in 125 ml glass separatory funnels. The time of contact of the solutions with the separatory funnels was kept at a minimum to reduce silica contamination. The measured phases were separated into 400 ml polyethylene beakers and the metal contents of each were precipitated by addition of an excess of ammonium hydroxide. Precipitate from each phase was filtered on ashless filter paper, ignited at 800" to 1000°C for 45 min, weighed, and analyzed by X-ray fluorescence.5 Data tabulated in Table I1 and illustrated in Fig. 1, show that maximum separation of tantalum from columbium for each HF concentration was obtained with no HCl present. The purest tantalum product was obtained with some HCl present. The highest separation factor was obtained at 2 N HF and

Jan 1, 1970

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley' in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By G. Baralis, P. Gondi, I. Tangerini, G. Scandola

The precipitation behavior of Zn-0.5 pct A1 alloy single crystals was studied by means of electrical resistivity measurements and by optical and electron microscopy. The single crystals for the resistivity measurements were prepared by an original method in - 100-p -thick sheets. The order of the precipitation kinetics ranged between 1 and 1.5. The dislocations play a relevant role in the first-order kinetics. Precipitation always occurs both on dispersed particles and on dislocations. Statistical examinations have shown that the first-order kinetics can have two different activation energies; i.e., the precipitation can have dz;fferent mechanisnrs which could not be identified, however, in the course of the research. During the tnetallographic exanzination of the precipitation structures a specific process of dislocation decoration was obsereed. The main purpose of this work was to study the contribution of dislocations to the precipitation. A number of authors have observed precipitation on dislocations and reference might be made to several monographs on the ubject.'' The possibility that dislocations also accelerate precipitation has been considered by Turn-bull3 and Fischer et al.4 The studies described in the present paper were carried out on zinc, chosen as a base metal owing to the ease with which dislocations can be introduced into it and because of the absence of excess vacancies after quenching in conditions where phenomena of accelerated precipitation still occur. Aluminum was preferred as alloying element because of the accelerated precipitation phenomena that resulted in a preliminary reearch. EXPERIMENTAL METHODS The observations refer to a Zn-0.5 pct A1 alloy. The zinc was 99.995 pct pure; a typical spectroscopical analysis is given in Table I. As a rule the alloy was subjected to homogenization, quenching, or slow cooling and annealing. Homogenization was carried out by heating at 390" to 410°C for 24 hr. From the homogenization temperature, some specimens were quenched and some slowly cooled at a rate of 2°C per sec. At this rate no precipitate was detectable under the optical microscope just after cooling. Quenching was carried out simply by dropping the specimens into water, aqueous ethylene glycol solution at -30" c, or liquid-nitrogen baths placed close to the homogenization oven. Vaseline oil baths were used with a thermal stabilization of 10-20 for both the aging treatments and the measurements; aging was generally carried out at 90" or 130°C. To avoid oxidation phenomena during heating, the vaseline oil baths had to be frequently renewed. The precipitation kinetics were studied by means of electrical resistivity measurements, using ans potentiometric method (reproducibility ± 5 x 10 5 v, that is 0.5 pct of the total voltage decreases on the specimens during precipitation). First, various types of specimens were tested, i.e., polycrystals, single crystals grown in capillary quartz tubes, and thin single-crystal sheets prepared by means of an original method requiring no container except for the natural oxide. Even if fully annealed, the polycrystals and the capillary grown single crystals showed resistivity in -creases, most probably due to dislocations introduced in the course of the measurements. Similar resistivity increases in pure zinc were noticed by another author. Only the single-crystal sheets showed no resistivity change; thus they were chosen for the subsequent tests. As already mentioned, these single crystals were obtained by using, as a container, the natural oxide on the zinc surface; the oxide strength is sufficient to maintain the original shape during melting with sheets up to 500 p thick. An initial zone melting and subsequent zone leveling, which led also to formation of the single crystals, were thus carried out on rolled sheets of the required thicknesses (- 100 p) and shape, lying on a flat silica surface. The resistivities were first evaluated by measurements at the liquid-nitrogen temperature. This method gave poor reproducibility, however, and this was attributed to the thermal cycles which had to be operated. To avoid cycles and handling, it was therefore decided to make measurements directly in the annealing oil baths; this required thermal stabilization at ilo-' "C. In this way only the resistance changes were measured. Specimens of pure zinc and of completely annealed alloy were always examined as controls together with those under consideration; only those measurement runs were taken into account where the reference samples showed no resistance increases. Again, the main inconvenience was due to oxidation and this was avoided by renewing the oil baths; even so data reproducibility was poor and the observations were therefore carried out on a large number (many hundreds) of specimens so as to provide indications of statistical value. For the transmission observations under the elec-

Jan 1, 1969

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By E. M. Elkin, J. H. Schloen

All known methods of treating and recovering the various components of copper refinery slimes are discussed. The slimes treatment processes presently used by five copper refineries are described and flowsheets are given. A bibliography is appended. THE recent increase in anode copper production at the Noranda smelter placed an additional load on the Montreal East plant of Canadian Copper Refiners Limited. The consequent increase in the amount of anode slimes led to a careful consideration of the various methods of slimes treatment. A critical review of these methods is presented here in the belief that it would be of interest to copper refiners. No such review has yet been published, although a number of individual flowsheets have been described. To make the information of greater value, a questionnaire was sent to all copper refineries. While the overall response to the questionnaire was not entirely satisfactory, the foreign refiners gave much detail in their answers and expressed willingness to cooperate further if needed. Although the data below do not cover all refineries, it is thought that examples of all flowsheets currently in use are included. A comparison of these flowsheets should prove of interest. The paper is divided into two parts. One part deals with a discussion of all known methods of treating and recovering the various components of the slimes. The second describes the processes now in use at various copper refineries for the treatment of raw slimes up to the production of Doré bullion. A brief description of the two main electrolytic methods of parting Doré bullion is appended. Since the first commercial application of electrolytic refining of copper by J. B. Elkington in 1865, the treatment of anode mud or slimes has undergone many changes. The object of treating slimes has always been the recovery and separation of precious metals. With the passage of time, increasing attention has been paid to improvement in recovery and quality of byproducts, mainly selenium and tellurium. The original methods of treatment were crude, although relatively direct. For example," the slimes were fused on a dolomitic clay bed in a reverbera-tory furnace; the slag was removed and the resulting metal cupelled to silver and gold. In another process, the dried slimes were oxidized and scorified on the lead bath of a cupelling furnace. Later, these pyrometallurgical methods were modified by sulphuric acid leaching, followed by fusion with niter in a reverb eratory furnace. A preliminary oxidizing roast improved the leaching step. Straight hydro-metallurgy has not found practical application. No matter what method is employed, the result is Dorb metal—a silver-gold alloy, with or without the metals of the platinum group. Characteristics of the Slimes Anode slimes are made up of those components of the anodes which are not soluble in the electrolyte. They contain varying quantities of copper, silver, gold, sulphur, selenium, tellurium, lead, arsenic, antimony, nickel, iron, silica, etc. The color of raw slimes is grayish black and the particle size is —200 mesh. However, Baraboshkin and Gaev (Ref. 1, p. 37), describe light gray colored slimes from the electrolysis of secondary copper which are composed predominantly of sulphates and of basic salts. In anode furnace practice primary and secondary metals are not usually segregated and such slimes do not commonly occur. Copper in the slimes originates to a large extent in the cuprous oxide of the anodes and is therefore dependent on the oxygen content of the latter: Cu2O + H2SO4 + CuSO4 + H2O + Cu [I] Opinions have been expressed that some of the copper is formed by decomposition of cuprous to cupric sulphate Cu2SO4 ? CuSO4 + Cu PI The product of either reaction is very finely divided. Depending on the slimes composition, much of the copper is combined with sulphur, selenium, tellurium, etc. The balance of the copper is in the free metallic state.

Jan 1, 1951

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By D. E. Coates, G. R. Purdy, S. V. Subramanian

The morphological stability of the planar solid-liquid interface in dilute ternary alloys, undergoing steady-state unidirectional solidification, is analyzed in terms of both the constitutional supercooling principle and the perturbation methods recently developed by Mullins and Sekerka. First, various steady-state solutions for the two solute distributions ahead of a planar interface are examined. The nature of the solutions depends on the size and concentration dependence of the off-diagonal diffusion coefficients. W~thin the framework of the constitutional supercooling principle, a cumulative contribution to instability frorn the two solutes is found to exist in the absence of diffusional interaction. It is shown that the latter can produce a further enhancement of instability or can have a stabilizing influence, depending on the form of the liquidus surface and on the sign of the solute-solute interaction. A perturbation analysis, which ignores diffusional interaction, verifies the cumulative influence of lhe solute fields and demonstrates that the Mullins-Sekerka stability criterion for binary systems (with capillarity accounted for) can be readily extended for application to ternary systems. SOME time ago, Tiller et al.' calculated the solute concentration distribution ahead of the planar solid-liquid interface of binary alloys undergoing steady-state unidirectional solidification. An earlier qualitative proposal that the transition from planar to nonplanar growth morphologies is associated solely with the onset of constitutional supercooling in the liquid layer ahead of the moving interface2 was used in conjunction with this calculation to put the now well-known constitutional supercooling (C-S) stability criterion into quantitative terms. Mullins and Sekerka,3 in a recent and very elegant analysis, established a more complete criterion (hereafter referred to as the M-S criterion). Interfacial stability was investigated by determining the time derivative of the amplitude of a sinusoidal perturbation of infinitesimal amplitude which had been introduced into the originally planar shape of the moving interface. Of particular importance is the fact that capillarity was included in the boundary conditions of their calculation. The purpose of the present paper is to extend all of this earlier work on dilute binary systems for application to dilute ternary alloy solidification. The analysis is divided into three sections. In the first the two solute distributions ahead of a moving planar interface are considered. Mathematical solutions are de- termined for situations in which: a) diffusional interaction is negligible, 6) diffusional interaction must be considered but circumstances permit use of constant diffusion coefficients, and c) the concentration dependence of off-diagonal diffusion coefficients can be described by first-order dilute solution approximations. In the next section, a stability criterion analogous to the C-S criterion is developed and the influence of diffusional interaction on interface stability is analyzed. Finally, the perturbation formalism of Mullins and Sekerka, with capillarity included in the boundary conditions, is extended for analysis of ternary systems in which diffusional interaction is negligible. The study of interface stability in binary systems usually commences with the assumption that the equilibrium distribution coefficient and the slope of the liquidus line are constant at values corresponding to infinite dilution. Similar assumptions have not been introduced into the present treatment; that is, we do not assume planar solidus and liquidus surfaces joined by tie lines which yield constant distribution coefficients. The latter involves the assumption of no ther-modynamic interaction between solute species in both the solid and liquid. We consider a ternary phase diagram for which the solidus and liquidus surfaces are, in general, nonplanar and of course pass through the corresponding binary solidus and liquidus lines. These lines are not assumed to have constant slope. In the dilute regions we are concerned with, the following assumptions are made: i) The solidus and liquidus surfaces are of a form such that both the solidus and liquidus temperatures are monotonically varying functions of each solute concentration. ii) The tie lines are such that the equilibrium distribution coefficient of a given solute is greater than unity for every point on the solidus (or liquidus) surface or it is less than unity for every point. STEADY-STATE SOLUTE DISTRIBUTIONS IN THE LIQUID As will be demonstrated in the next section, a knowledge of the steady-state solute profiles is not a necessary prerequisite for the formulation of a ternary C-S stability criterion. However, in that details, such as the complete description of the equilibrium liquidus temperature profile, require an evaluation of the solute distributions, the overall treatment is enhanced if these distributions are determined. Consider a ternary system (solvent plus solutes 1 and 2) for which a planar solid-liquid interface is in unidirectional motion at constant velocity V. At this stage it is unnecessary to limit ourselves to dilute solutions. For a stationary frame of reference the generalized forms of Fick's equations are:

Jan 1, 1969

By H. Shaw

Gravitational measurements made by means of the Eotvos torsion balance over any area enable a representation to be obtained of the total gravitational effects over the surface of that area arising from the combination of all sources of gravitational disturbance. The investigation of gravitational anomalies occurring in the upper layers of the earth's crust, in this way, has been attended with considerable success, and, especially in areas in which no undesirable disturbing factors were present, it has been possible to locate geological structures and mineral deposits with remarkable accuracy and also to delineate their confines and to indicate their depth below the surface with a certain amount of precision. Before this can be done successfully, however, it is necessary to determine the gravitational effect arising from all other extraneous anomalies in order that these may be satisfactorily eliminated. Disturbing features giving rise to these gravitational anomalies may be divided into two classes, according to whether they are situated at or below the surface. The former are determined readily by a detailed leveling of the ground surface, and may be satisfactorily eliminated provided the specific gravity of the terrain material is known, but the latter are generally unknown, and can only be ascertained with difficulty. When, therefore, the observations obtained by means of the Eotvos torsion balance have been corrected for all surface irregularities, known as terrain and topographical effects, there remain residual gravitational values which are due entirely to subterranean conditions. The. task of interpreting these results consists in disentangling the various subsurface anomalies, and subsequently in computing and recombining the effects of these various masses in order to verify the interpretation. When the gravitational anomalies are due to large and comparatively simple structures it is a matter of little difficulty to arrive at a satisfactory interpretation of the subterranean conditions, but in more complex areas, where the geological conditions are more complicated and several irregular features exist, the process of disentangling the various constituents of the complex mass arrangement is more difficult and requires the expenditure of considerable time and labor. When the subterranean effects have been obtained, they are subjected to a critical examination, and an effort is made to recognize and

Jan 1, 1932

By S. A. Bradford

Internal-oxide precipitates in decarburized a iron alloys were studied by microscopic and X-ray methods. Diffusion of oxygen is primarily trans-granular, although large amounts of manganese or PhosPhorus cause preferred grain boundary dimsion at temperatures below 1450OF. Transgvanular internal oxidation follows the parabolic rate law with an apparent activation energy of 60 kcal per g-atom for decarburized rimmed steel and around 50 kcal per g-atom for higher alloy contents. The internal oxide is (Fe,Mn)0. Evidence was found for a miscibility gap in the FeO-MnO system. UNTIL very recently, the internal oxidation of metals was studied primarily as a scientific curiosity or, in a few cases, as a means of strengthening alloys by precipitation hardening. However, with the recent development of low-carbon enameling sheet steel, internal oxidation has become a problem of practical importance to the steel industry. For example, in 1961 it was reported1 that internal oxidation of steel can occur during decar-burization by open-coil annealing and will reduce the notch ductility of the sheet unless the process is carefully controlled. The present study was therefore undertaken to learn more about the rates and mechanism of oxygen diffusion and oxide formation in iron alloys. BACKGROUND The process of internal oxidation has been well-defined in the literature:',' oxygen dissolves in an alloy, diffuses inward from the surface of the metal, and reacts to form a precipitate with the alloying element that will provide the most stable oxide. he growth of the finely divided so-called subscale, i.e., the internal-oxidation zone, depends on the diffusion rates of both the oxygen and the reactive element.4 Investigators have generally found that increasing the temperature increases the size of the oxide particles, the rate of subscale growth, and the tendency to transgranular diffusion. With very few exceptions, the square of the thickness of the internal oxide layer is directly proportional to the reaction time. Given two conditions easily satisfied for iron systems— a) an oxygen solubility much less than the concentration of the alloying metal and b) an oxygen-diffusion rate to the oxide boundary much faster than that of the alloying element—then the general expression developed by Rhines and co-workers5 for the parabolic growth rate of the internal-oxide zone can be simplified to the following form: where Co and CM are, respectively, the solubility of oxygen and the concentration of the alloying element, DO is the diffusion coefficient of oxygen, O/M is the weight ratio of oxygen to metal in the precipitated oxide, and x is the thickness of the internal-oxide zone after an annealing time t. Both the oxygen solubility and diffusion coefficient can be approximately expressed as functions of temperature by Arrhenius-type equations: in which H and Q are, respectively, the heat of solution and the activation energy of diffusion. Consequently, the apparent activation energies calculated from Arrhenius plots are the sum of the heat of solution of oxygen in iron and the activation energy for diffusion of oxygen. The data, if not the interpretation, of Schenck et al.8 bear out the fact that oxygen diffuses in the atomic form. The general rate law for atomic diffusion is: the reaction rate being proportional to the square root of the pressure at low pressures. Benard and Moreau8 studied both the surface oxidation of Fe-Ni alloys and the gradual penetration of oxygen into the metal. They observed that oxide particles first form along grain boundaries and then grow to form continuous films that eventually envelop the grains. The parabolic rate law does not usually apply in these cases, especially at the higher temperatures. The oxide formed is wustite which gradually transforms into Fe3O4 and finally into Kennedy and coauthors8 examined Fe-Ni alloys with 26, 75, and 84 pct Ni oxidized at 800°C and

Jan 1, 1964

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945