Search Documents

By Robert L. Voss, Richard D. Hagni

Sparry dolomite from all of the operating mines in the Viburnum Trend of Southeast Missouri have been found by cathodoluminescence microscopy to reveal a systematic pattern of banding resulting from a growth zoning within individual dolomite rhombs. Four principal bands have been recognized throughout the entire Trend and each of the major bands contain even finer internal banding. Minor bands a few microns in width can be correlated in specimens collected ten's of kilometers apart along the trend. The first three principal dolomite bands decrease from south to north. This feature, together with the fact that the white sparry dolomite crystals decrease in abundance from south to north in the Trend, suggests that a major source for the fluids was from the south. The application of cathodoluminescence microscopy to crystalline dolomite demonstrates a strong correlation between ore grade and the intensity of internal banding and dissolution textures.

Jan 1, 1985

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has-been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1 volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 904 volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

By W. H. Emmons

INTRODUCTION THE deposition of metalliferous lode systems takes place at considerable depths and no one may observe the process. We see only the end results of the process and from these we seek to construct a theory that will account for them. Because there is an obvious relation between many lode systems and intrusive igneous masses, it is a natural inference that they have formed by fluids that were expelled from such masses. The metalliferous lode systems have been deposited by ascending thermal fluids that have risen mainly from great irregular bodies of intruding magmas which are called batholiths. Probably 95 per cent of such lode systems have formed in connection with acidic or "granitic" batholiths and probably less than 5 per cent have formed in connection with basic intrusives. The study of lode ores, therefore, should include the study of the intrusion and differentiation of the batholith. It was noted long ago1 that certain tin-bearing deposits are commonly associated with small stocks. That small stocks are cupolas of larger intrusive masses has generally been recognized. Butler,2 in his studies of the ore deposits of Utah, showed that the chief deposits in Utah are in and near the stocks; that is near the "apically truncated

Jan 1, 1933

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By Horace H. Emerich

PrePatory Note.—The first part of this paper was sent to me by Mr. Emrich nearly nine months ago; and I held it, waiting for the second part, which he had promised to forward soon, so that I might submit the whole to some of his former professional associates, and advise him of their criticisms and suggestions before off'ering his work to the Institute. But, five days before the second part reached me, I received by telegraph the news of Mr. Emrich's sudden death. The paper has therefore not had the benefit of such a revision by the author as might have made it ill some respects clearer and more cornplete. Nevertheless, I believe that experts in the branch of metallurgy with which it deals will find it both original and suggestive.—A. Eilers. I. Partial ReFining iN the ANode-Furnace. During my connection with one of the large New Jersey copper-refineries, and probably before that period, from 15 to 30 per cent. of the copper-bullion received was the very foul, leady blister-copper produced from lead blast-furuace matte. It had been customary to mix a small part of this blister with each charge of purer pig-copper, in the effort to dilute it as much as possible before casting into anodes; but tank-house conditions were such that I was led to try making entire furnace-charges of this blister, and refining it as much as possible in the furnace—afterwards casting to anodes and refining elec-trolytically, in tanks and solution separate from the main bulk of the purer copper. In making this experiment, notes were made, for several furnace-charges, of everything thought to have a bearing on the question, and some interesting facts were brought out, both in the furnace-working and afterwards in the tanks.

Jan 1, 1913

By Marshall D. Himes

The Pima mine, Pima County, Ariz., a 53,500-tpd copper mine, is located 17 miles south of Tucson, Ariz. The mine is in a sequence of Paleozoic and Mesozoic sediments striking east-north-east and dipping southeasterly. These sediments are intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian (?) dolomites, limestones, and sandstones have been altered to calc-silicate skarn, marble, and quartzite. The overlying Mesozoic Triassic (?) clastic sediments have undergone some recrystallization and hydrothermal alteration. The clastic metasediments are divided into three distinct lithologic units: lithic arenite, arkose, and interbedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite, and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar, quartz, and sericite, with or without chlorite and calcite). The porphyry has undergone potassic alteration. Dominant structures are an east-west postmineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. The two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast, and the other striking northeast, dipping northwest. Economic mineralization is prediminantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are less important amounts of magnetite, hematite, sphalerite, galena, tennantite, and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1974

By E. T. Dumble

In continuation of the geological work begun in Sonora, Mexico, a partial account of which has already been given in the Transactions of the Institute,* a similar reconnaissance was made of Cochise county, Arizona, and a part of the Whetstone mountains. The investigation resulted in the identification of beds of similar age and character to those of the Sonora region, and in the discovery of interesting deposits, which, so far as I call ascertain from the literature at my command, have not been described heretofore. Route.—Starting from Nogales, we followed the railroad to Crittenden, and then drove to the southeastern slope of the Whetstones. After a brief examination of some reported coalbeds we continued our route, following the wagon-road between the Whetstones and the Mustang mountains to Huachuca, and eastward to Tombstone. Crossing the Dragoon mountains at South Pass, we traveled south and west by way of Turquoise and Antelope Spring into the road from Tombstone to Bisbee. Our route over the Mule mountains lay through Mule Pass and Bisbee, where we stopped a day or two. Thence, crossing Sulphur Spring valley, we drove around the southern end of the Swisshelms, and N. through the valley between these mountains and the Chiricahuas, to White river. From that point our way led through Rucker canon into the San Simon valley, then northward along the eastern face of the Chiricahuas, and by way of Fort Bowie to Willcox, Arizona, from which place we returned to Nogales. It was greatly regretted that the extremely wet weather prevented us from including in our examination the Huachuca

Jan 1, 1902

By H. S. Chiang, S. S. Peng

INTRODUCTION Underground coal mining disturbs the original in-situ conditions which induces a series of strata activities and results in creating "mine pressures," the source of all ground control problems. Adoption of self advancing powered supports in modern longwall mining adds a new dimension to ground control problems and thus research. Roof stability, in general, refers to the integrity and stability of the immediate roof which is measured by the maximum exposed area and time duration without support. There are many factors that con- tribute to roof stability problems. In addition to mining height, rock property and stratum components and caving angle of the immediate roof, characteristics of joints and fissures and their degrees of development, faults and underground water, the operational techniques also play a very important role. This paper summarizes these operational techniques and methods of controlling stable and unstable roof. CLASSIFICATION OF THE IMMEDIATE ROOF There are many ways of classifying the roof (1). For practical purpose, the immediate roof in this paper is divided into three groups, i.e. unstable. medium stable and stable. Unstable Immediate Roof It has the following features (1) It consists of weak or soft carbonaceous shale, black shale, clay shale and well-jointed or fractures sandy shale

Jan 1, 1983

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. DIATOMS More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the fresh-water diatomites on the Pacific Coast are: [Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralf s Diatoma vulgare Bory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kutaing Stictodiscus niagarae Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg]

Jan 1, 1939

By D. J. Jr. McAdam

Fort the past five years, an investigation of the endurance properties of metals has been in progress at the U. S. Naval Engineering Experiment Station, Annapolis, Md. As a result of the investigations at this Station1-5 and other laboratories6-11 "endurance limits" of practically all kinds of carbon and alloy steels have been determined and have been correlated with other physical properties, especially with tensile strength. About a year and a half ago, the investigation at the Naval Experiment Station was shifted to non-ferrous metals. As a result, several papers discussing the endurance properties of numerous non-ferrous metals and alloys, especially the alloys of nickel and of copper12-16 have been published. In these papers, stress-cycle graphs illustrate. the endurance properties of each individual metal and alloy, and other graphs illustrate the effect of cold working, heat treatment, and chemical composition on endurance and other physical properties. Endurance tests of non-ferrous metals were made by the machines used in the endurance tests of ferrous metals. 1-4 The specimen for the rotating-cantilever tests, which has been described, 1,2,13 has a conical surface, with taper so adjusted that the stress is nearly uniform over a length of about 1 ½ in. Alternating torsion tests were made with the machine of the inertia types17 and usually by an accelerated-fatigue method.12 As the rotating-cantilever endurance limits of metals are about twice the alternating-torsion endurance limits, the former values are more generally useful in correlating the endurance properties of nonferrous metals. In several recent papers by the writer13-16 correlation of the endurance properties of a number of non-ferrous metals has been discussed.

Jan 10, 1925

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

By J. D. Davis, A. C. Fieldner

The older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer,' who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter"g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 1, 1925

By E. Goldin, H. J. Juretschke

THE electrical properties of porous conductors have been studied ever since such materials, usually prepared by pressing and sintering of metallic powders, obtained practical importance. In most cases, however, the results have not been easy to interpret because of the great number of independent variables such as powder size, pressure, pressing rate and temperature, subsequent thermal history, porosity, and so on, which enter into the fabrication of industrially desirable materials. In recent years an interpretation of these properties has become of interest because the electrical properties of many new substances, prepared as fine powders by crystallization from the vapor phase or by reactions in the solid state at high temperatures, have to be determined on porous samples formed from the powder. Since theoretically significant information must refer to the fully dense state of the material, it is important to relate the electrical properties measured on such porous samples to those expected for a sample of 100 per cent density. A simple theory for the porosity dependence of the electrical conductivity and the Hall effect was recently proposed by Juretschke, Landauer, and Swanson.' Their model, assuming a distribution of pores of equal size and shape, sufficiently far apart so that each pore is embedded in a region of uni-

Jan 1, 1959

By J. A. Church

I. Early Furnaces,......423 11. Experiments with the HIgh-Shaft FURnace,..... 426 III. ExperMents wIth the Wide FURnace,..429 IV. ExperEentS with Extreme BOSH,... 43.2 V. Survival of the 56 by 180 IN. Furnace,.434 VI. Recent ExpeEiments,.....436 VII. SUMMary,........438 I. Early Furnaces. Copper blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in.; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 1, 1914

By R. B. Russell

SINCE Cahn's¹ paper on plastic deformation in orthorhombic (a) uranium an increasing amount of work is to be expected on orientation of single crystals and preferred orientation in this metal. It would seem desirable to have a table of angles between crystallographic planes (hkl) and (HKL). Table I shows these angles as distances from (loo), (0l0), and (00l), and in Fig. 1 as a standard (001) stereographic projection. Only the locations of poles whose diffracting planes produce Cu Ka reflections up to 0 = 70.5" (i.e. (154) ) are given." The relative reflection of these planes are represented by circle diameters. It is hoped that the projection may also be used in making inverse pole figures, originally suggested by Harris.' Values of 4 were calculated from the expression hH kK 1L cos = hH/a²+kK/b²-lL/c² where the lattice parameters a, b, c, and the spac-ings d were taken from the work of Jacob and Warren." (They report a = 2.852 kX (2.8578 A), b = 5.865 kX (5.8768 A), c = 4.945 kX (4.9550 A).) The parameters reported by them may be subject to revision,4,5 accordingly the interplanar angles are listed to only the nearest tenth of a degree. References ¹R. W. Cahn: Acta Metallurgica (1953) 1, p. 49. ¹G. B. Harris: Philosophical Magazine (1952) 43, p. 113. 3C. W. Jacob and B. E. Warren: Journal ACS (1937) 59, p. 2588. 4J. S. Lukesh: Acta Crystallographica (1949) 2, p. 420. ³ J. Thewlis: Nature (1951) 168, p. 198.

Jan 1, 1954

By J. B. Clark, A. S. Yue

IN recent years, zone melting1 has been applied extensively to the purification of metals having a very low vapor pressure.2-4 This note describes the zone melting of a high vapor-pressure metal, magnesium, where the melting takes place inside a refractory surface skin. The effects of zone speed and the number of passes of the molten zone on the purification have been determined and the effective distribution coefficients for the principal impurity elements were calculated. A schematic diagram of the zone-melting apparatus is given in Fig. 1. The Vycor tube containing the graphite boat with its magnesium charge (an extruded rod—3/8 in. in diam, 10 in. long) is pulled through the stationary furnaces. A molten zone approximately one-fourth the length of the charge is produced under each of the two central furnaces. Two grades of magnesium were studied—electrolytic magnesium and magnesium with a very low alloy content. The spectrographic analyses of these materials, within * 5 pct of the values stated, are given in Table I. Molten magnesium will vaporize severely if protected only by an inert atmosphere such as argon. Consequently an enveloping container is required. In zone melting, a rigid opaque container surrounding the charge is inconvenient because visual control of the zone length is prevented. A more satisfactory container is a strong flexible skin on the surface of the metal charge which is capable of supporting the molten zone. SO2 reacts with magnesium to form a thin coherent surface film of MgSO, and MgO. An atmosphere of SO, of commercial purity was maintained during the zone melting. Enough oxygen was present within the system and the commercial SO, for the satisfactory formation of the protective skin, so that any rupture of the skin during the zone refining was healed immediately.

Jan 1, 1959

By John C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert, Russell, Le Conte, Spur, Louderback, and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea.

Jan 3, 1960

By James Douglas

At this last meeting of our Institute for the year 1899, it is appropriate that we should look back at the past. To review the century's progress in the exact sciences and the resulting arts that fall within the scope of our labors is beyond my ability. But I wish to draw your attention to some phases of that progress, almost as important, which lie within the zone of sociology, touching at so many points the domain of applied technology. One of these is suggested by the library of technical literature which this century has produced —not the least important contribution to which is our own Transactions. The nineteenth century has witnessed the beneficial spread of democracy in politics. Under the impulse, to no small degree, of the same spirit, there has grown up a brotherhood of fellow-workers and a sense of fellow-ownership in the secrets of nature. Though the Patent Office has assumed such proportions as to hare become a source of national revenue, and a multitude of inventors, great and small, are seeking through its agency to secure some pecuniary profit from their devices, there is even greater eagerness among both interested and disinterested workers in the field of technology to publish their observations, and even their discoveries, and to give them to the world without remuneration. The motives influencing the great body of writers who, without any pay, use the technical journals and such media of communication as our Transactions, in order to give to the brethren of their craft the results of

Jan 1, 1900

By Leonard Klein

Reduction of oxygen-containing copper has always heretofore been brought about with wood poles. This paper reveals the first successful, economical, and Practical substitute for poles: a gaseous reductant, of which the production and plant use are detailed herein. THE art of fire refining of copper, consisting of melting, oxidation, slag removal, and finally reduction with wood poles, has been practiced for many centuries. An authentic record, discussed in detail in De Re Metallica,* mentions that as early as 1200 A.D. workers in this field of metallurgy were already acquainted with and practiced the basic principles of copper purification. Undoubtedly, the art was well developed marly centuries before the first written records began to appear. Notwithstanding the many advantages gained by application of mechanical con. trivances and by the tremendous increase in size of operations over the centuries, the reduction phase of the process has persisted essentially the same to the present time except for a very recent breakthrough. Numerous articles have been published and many patents have been issued on the subject of substitutes for wood poling in the past half century. They have dealt with a variety of gaseous, solid, and liquid reducing agents. But to the knowledge of the writer, no procedure has ever been prosecuted to a complete success on a large operating plant scale with the single exception of gaseous reduction of oxygen-containing copper revealed in detail herein. A natural gas-air reformer with ample capacity for

Jan 1, 1962

By William H. Emmons

The problem of the metalliferous veins has always been an outstanding one in the science of ore deposits. In recent years interest has been stimulated by Spurr, who maintains that veins have consolidated from magmas that have densities as great as the densities of ordinary rocks. Lindgren published a noteworthy paper1 in 1926, in which he supports the theory that veins are deposited chiefly by hot waters. Lindgren's paper was discussed by Singewald, Spurr, Kemp, Anderson, Colony, Bateman, Porter and others. The discussion, in the main, was centered on the interpretation of fragments that are included in veins. This paper also treats the problems of fragments in veins and includes a reply to a review by Spurr2 of a bulletin by Larsen and myself3 published by the United States Geological Survey on the geology and ore deposits of Creede, Colorado. Mineral veins containing fragments of the wall rock are common. At many places the fragments are completely isolated, one from the other, and are entirely surrounded by vein matter. It has been stated that the vein matter around the fragments was heavier than the fragments and that the latter were floated in a magma. J. E. Spurr, who is the leading advocate of this hypothesis, 4 urges that normal mineral veins were deposited by solutions heavy enough to float fragments of the country rock, and it is mainly on this relation that he bases his theory that veins are deposited by solidification of magmas. If it can be shown that vein-forming solutions have a specific gravity greater than rock (2.77), one is justified in regarding them as true mag-matic solutions. It is shown later in this paper, however, that at Lead, S. D., water not more highly concentrated than ordinary drinking water is depositing vein matter around fragments of schist and of steel in such a manner that the fragments are completely isolated and completely surrounded by the mineral cement.

Jan 1, 1928